Toshiba e-STUDIO195, e-STUDIO245, e-STUDIO225, E-Studio 182, E-Studio 212 Operator's Manual
...
MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator's Manual
for Copying Functions
Preface 1
Preface
Thank you for purchasing the TOSHIBA multifunctional digital systems.
We have provided you with this manual for the operation of this equipment.
This operator’s manual describes the following:
y How to use this equipment
y How to inspect and carry out maintenance on this equipment
y How to remedy mechanical and copying problems
Be sure to read this manual before using this equipment. Keep this manual handy and retain it
for future reference.
2 Notice to Users
Notice to Users
For EU only
After a suitable place has been selected for the installation of the e-STUDIO195/225/245, please do not
change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide proper ventilation as
the copier emits a small amount of ozone.
The unit is classified as Class 1 Laser Product according to IEC60825-1:1993, IEC60825-1:2007
including amendments.
The unit uses laser diode of output Max. 5 mW, wave length 785 nm, continuous pulse.
Caution:
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Working environment
From EMC (Electromagnetic Compatibility) point of view, the operation of this product is being restricted
in following environments:
y Medical Environments: This product is not certified as a medical product according to the Medical
Product Directive 93/42/EEC.
y Domestic environments (e.g. a private living room with TV / Radio sets in the nearby surrounding
area) because this is a so called EMC class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures!
Any consequences resulting from the use of this product in restricted working environments are not the
responsibility of TOSHIBA TEC.
The consequences of the use of this product in restricted working environments may be an electromagnetic interference with other devices or machines in the nearby surrounding area. This can result into
malfunction including data loss / data error pertaining to this product or the other devices / machines
involved in the electromagnetic interference.
Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted.
CE compliance
This product is labelled with the CE mark in accordance with the provisions of the applicable European
Directives, notably the Low Voltage Directive 2006/95/EC, the Electromagnetic Compatibility Directive
2004/108/EC for this product and the electric accessories, the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/EC for the telecommunication accessories.
CE marking is the responsibility of TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH, CarlSchurz-Str. 7, 41460 Neuss, Germany, phone +49-(0)-2131-1245-0.
For a copy of the related CE Declaration of Conformity, please contact your dealer or TOSHIBA TEC.
Notice to Users 3
For EU only
Following information is for EU-member states only:
This product is marked according to the requirement in EU-Directive 2002/96/EC.
(Directive on Waste electrical and electronic equipment - WEEE)
The use of the symbol indicates that this product may not be disposed as unsorted municipal waste and
has to be collected separately. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of this product please contact your supplier where you purchased the product.
Following information is for EU-member states only:
Disposal of batteries and/or accumulators
(based on EU-Directive 2006/66/EC,
Directive on batteries and accumulators and waste batteries and accumulators)
By ensuring that batteries and/or accumulators are disposed of correctly, you will help prevent potential
negative consequences for the environmental and human health, which could otherwise be caused by
inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of batteries and/or accumulators, please
contact your supplier where you purchased this product.
4 Before Reading This Manual
Before Reading This Manual
Lineup of our manuals
These manuals are provided for the operation of the e-STUDIO195/225/245. Select and read
the manual best suited to your needs. This manual is the Operator’s Manual for Copying
Functions.
Basic functions
Facsimile functions
The Fax Kit GD-1221 (optional) is necessary for using the Fax functions.
Printing functions
The Network Printer Kit GA-1192 (optional) is necessary for using the printing functions.
Operator’s Manual for Copying Functions (Booklet, This manual)
This manual describes the basic operations, mainly copying functions, of this equipment. It
also describes safety precautions to ensure correct and safe use of this equipment. Be sure to
read this before you use the equipment.
Operator’s Manual for Facsimile Function (Booklet)
This manual describes how to use the Fax functions. Various functions both basic and
advanced regarding Fax transmission/reception are available.
Quick Start Guide for Printing Functions (Booklet)
This manual gives basic information regarding the printing functions, such as the GA-1192
accessories, necessary environmental conditions and outline of network connections as well
as troubleshooting. Be sure to read this before using the printing functions.
Network Administration Guide for Printing Functions (PDF file)
This manual describes the operation necessary for configuring a network and using the printing functions, such as connecting to a network and setting components.
Setup Guide for Printing Functions (PDF file)
This manual consists of the following two parts.
Control panel:This part describes how to configure the printer-related settings using the con-
trol panel of the equipment.
TopAccess: This part describes how to use the co-packed utility “TopAccess”. The settings
and management of the equipment can be done using a Web browser.
Printing Guide (PDF file)
This manual describes the operation necessary for printing data from a computer, such as the
installation of the client software and the use of the printer driver.
Network Fax Guide (PDF file)
This manual describes the operation necessary for sending a Fax from a computer via a network, such as the installation of the client software, use of the N/W-FAX driver and the copacked application software “AddressBook Viewer”.
Before Reading This Manual 5
Scanning functions
The Scanner Upgrade Kit GA-1202 (optional) is necessary for using the scanning functions.
To read manuals in the PDF file format
The operator’s manual in the PDF (Portable Document Format) can be displayed/printed using
Adobe Reader or Adobe Acrobat Reader. If neither is installed in your computer, download one
of them. This can be done via the website of Adobe Systems Incorporated.
Quick Start Guide for Scanning Functions (PDF file)
This manual gives the basic information regarding the scanning functions, such as the GA1202 accessories, necessary environmental conditions and outline of network connections as
well as troubleshooting. Be sure to read this before using the scanning functions.
Network Administration Guide for Scanning Functions (PDF file)
This manual describes the operation necessary for configuring a network and using the scanning functions, such as connecting to a network and setting components.
Setup Guide for Scanning Functions (PDF file)
This manual consists of the following two parts.
Control panel: This part describes how to configure the scanner-related settings using
the control panel of the equipment.
TopAccess: This part describes how to use the co-packed utility “TopAccess”. The
settings and management of the equipment can be done using a Web
browser.
Scanning Guide (PDF file)
This manual describes the operation necessary for using the scanning functions, such as the
installation and the use of the TWAIN driver.
6 Before Reading This Manual
How to read this manual
Symbols in this manual
To ensure correct and safe use of this equipment, this operator’s manual describes safety precautions according to the three levels shown below.
You should fully understand the meaning and importance of these items before reading this
manual.
Other than the above, this manual also describes information that may be useful for the operation of this equipment with the following signage:
Description of original/paper direction
Paper or originals of A4 or B5 size can be placed either in a portrait direction or in a landscape
direction. In this manual, “-R” is added to this paper size when this size of paper or original is
placed in a landscape direction.
e.g.) A4 size original on the original glass
Paper or originals of A3 or B4 size can only be placed in a landscape direction, therefore “-R” is
not added to these sizes.
Indicates a potentially hazardous situation which, if not avoided, could result
in death, serious injury, or serious damage, or fire in the equipment or surrounding assets.
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury, partial damage of the equipment or surrounding
assets, or loss of data.
Indicates information to which you should pay attention when operating the
equipment.
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these
pages as required.
Placed in a portrait direction: A4 Placed in a landscape direction: A4-R
Before Reading This Manual 7
Screens
Screens on this manual may differ from the actual ones depending on the use-environment of
the equipment such as the installing status of options.
Trademarks
y Microsoft, Windows, Windows NT, and the brand names and product names of other
Microsoft products are trademarks of Microsoft Corporation in the US and other countries.
y Adobe, Adobe Acrobat, Adobe Reader, Adobe Acrobat Reader, and PostScript are trade-
marks of Adobe Systems Incorporated.
y Other company and product names given in this manual or displayed in this software may be
the trademarks of their respective companies.
©2011 TOSHIBA TEC CORPORATION All rights reserved
Under the copyright laws, this manual cannot be reproduced in any form without prior written
permission of TOSHIBA TEC CORPORATION.
CONTENTS 9
CONTENTS
Preface........................................................................................................... 1
Notice to Users ............................................................................................. 2
Before Reading This Manual ....................................................................... 4
TOSHIBA Quality Is Second to None........................................................ 15
General Precautions................................................................................... 18
Disclaimer Notice ....................................................................................... 25
Environmental Information........................................................................26
Chapter 1 PREPARATION
Description of Each Component...............................................................28
Front / Right side ..................................................................................... 28
Left side / Inner side ................................................................................ 29
Configuration of options...........................................................................31
Control panel ........................................................................................... 32
“Copy mode” main screen ....................................................................... 35
Preparation 1 - Turning Power ON............................................................36
Turning power ON ................................................................................... 36
Saving energy when not in use - Energy saving mode - ......................... 37
Preparation 2 - Placing Copy Paper..........................................................39
Acceptable media types ..........................................................................39
Recommended paper.............................................................................. 40
Placing paper in drawers......................................................................... 41
Placing paper in the drawers of Paper Feed Pedestal (optional) ............45
Preparation 3 - Registering Size of Paper Placed ...................................49
Registering standard size (A3, A4, A4-R, A5-R, B4) ...............................49
Registering other standard sizes .............................................................50
Chapter 2 HOW TO MAKE COPIES
Placing Originals ........................................................................................54
Acceptable originals ................................................................................ 54
Placing originals on the original glass ..................................................... 55
Placing booklet-type originals such as books or catalogues ................... 56
Using Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional)................................................... 57
Placing originals on Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional)................................................... 58
Making Copies ............................................................................................59
Stopping/Resuming copying.................................................................... 61
Interrupting copying and making another copy - Interrupt copy - ............ 62
10 CONTENTS
Using Bypass Tray .....................................................................................63
Bypass copying ....................................................................................... 64
Chapter 3 COPYING FUNCTIONS
Before Making Copies................................................................................68
Default settings........................................................................................68
Confirming set functions.......................................................................... 68
Paper Selection........................................................................................... 69
Automatic paper selection (APS)............................................................. 69
Manual paper selection ...........................................................................70
Copying Different Sizes in One Go - MIXED-SIZE COPYING - .............. 72
Zooming In/Out Copy Image...................................................................... 74
Automatic magnification selection (AMS) ................................................74
Specifying both the sizes of the original and the copy paper ..................76
Specifying reproduction ratio manually.................................................... 77
Selecting Image Mode................................................................................ 78
Adjusting Density Level.............................................................................79
Chapter 4 ADVANCED COPYING FUNCTIONS
Copy Menu .................................................................................................. 82
Operating in copy menu ..........................................................................82
Copy function list ..................................................................................... 83
Copying in Same Page Order as Originals - Sort Copying - ................. 84
Sorting Alternately One Set by One - ALTERNATION - ......................... 85
Sorting in Magazine Type Arrangement - MAGAZINE SORT - .............. 86
Shifting Paper to Make Margin - IMAGE SHIFT - .................................... 88
Erasing Shadow on Edge - EDGE ERASE - ............................................90
Copying on Both Sides - DUPLEX - ......................................................... 92
Copying on one side................................................................................ 93
Copying on both sides ............................................................................. 94
Copying booklet on both sides ................................................................96
Copying Right and Left Pages Separately - DUAL PAGE - .................... 99
Printing Page Number, Date and Time - ANNOTATION - .....................101
Changing Copy Setting on Each Job - JOB BUILD - ............................ 103
Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 - .................................... 105
Copying Both Sides of Card into 1 Page - ID CARD - ..........................108
CONTENTS 11
Changing Sizes in Horizontal and Vertical Directions - XY ZOOM - ... 111
Registering Functions Frequently Used - JOB MEMORY - .................113
Registering combination of functions..................................................... 113
Recalling combination of functions ........................................................ 114
Chapter 5 CHANGING EQUIPMENT’S SETTINGS
Before Changing the Settings ................................................................. 119
Displaying the “user functions mode” main screen................................ 119
Operating buttons for changing the settings..........................................120
Date and Time ........................................................................................... 121
Clock setting ..........................................................................................121
Date and time display ............................................................................ 123
Display Language Setting........................................................................ 124
Paper Size Setting ....................................................................................125
Walkup Screen Setting............................................................................. 127
Timer Setting.............................................................................................129
Time of automatic function clear............................................................129
Time of automatic low power mode....................................................... 130
Time of automatic sleep mode / super sleep mode............................... 132
Energy Saving Mode Setting ...................................................................134
Weekly Timer Setting ...............................................................................136
Volume Adjustment.................................................................................. 139
Touch Key Tone Setting .......................................................................... 141
Department Code...................................................................................... 143
Setting department codes ..................................................................... 143
Changing department names or codes .................................................147
Deleting department codes.................................................................... 150
Clearing counter values......................................................................... 152
Printing out counter values .................................................................... 154
Canceling department management ..................................................... 155
Menu Customize ....................................................................................... 157
APS / AMS ................................................................................................. 159
Image Mode............................................................................................... 161
Density Adjustment..................................................................................163
Finishing Mode .........................................................................................165
Pop-Up Display Setting............................................................................167
Various List Printing ................................................................................169
12 CONTENTS
Menu List Printing ....................................................................................171
ROM Version Display ...............................................................................172
Chapter 6 TROUBLESHOOTING
When This Message Appears..................................................................174
Paper Jams ...............................................................................................176
Checking position of paper jams ........................................................... 176
When paper jams occur frequently........................................................177
When releasing jammed paper.............................................................. 177
Paper jams within Reversing Automatic Document Feeder (optional)
(Lower) / Automatic Document Feeder (optional) (Lower) ....................178
Paper jams within Reversing Automatic Document Feeder (optional)
(Upper) / Automatic Document Feeder (optional) (Upper) ....................180
Paper jams on bypass tray....................................................................182
Paper jams within Automatic Duplexing Unit (optional).........................182
Paper jam behind transfer unit ..............................................................183
Paper jams within fuser unit .................................................................. 185
Paper jams within Paper Feed Unit (optional)....................................... 187
Paper jams within Paper Feed Pedestal (optional) ...............................189
Replacing Toner Cartridge ......................................................................190
Before Calling Service Technician..........................................................197
General operation.................................................................................. 197
Toner-related items ...............................................................................198
Original/Copy paper-related items......................................................... 199
Image trouble ........................................................................................199
Chapter 7 MAINTENANCE AND INSPECTION
Daily Inspection ........................................................................................ 204
Cleaning charger ................................................................................... 205
Cleaning transfer charger...................................................................... 206
Chapter 8 SPECIFICATIONS AND OPTIONS
e-STUDIO195/225/245 Specifications .....................................................210
Continuous copying speed .................................................................... 211
Specifications of Options ........................................................................ 212
Packing List ..............................................................................................214
Copying Function Combination Matrix ..................................................215
Combination Matrix 1/2.......................................................................... 215
Combination Matrix 2/2.......................................................................... 216
CONTENTS 13
List Print Format....................................................................................... 217
Department code list..............................................................................217
Function list ........................................................................................... 217
Supply notice list....................................................................................218
Mailbox list.............................................................................................218
Configuration page list........................................................................... 219
NIC status page list ............................................................................... 219
Menu list ................................................................................................220
INDEX .......................................................................................................................................221
14 CONTENTS
TOSHIBA Quality Is Second to None 15
TOSHIBA Quality Is Second to None
Recommended toner cartridges
To assure optimal printing performance, we recommend that you use only genuine TOSHIBA
toner cartridges.
If you use a TOSHIBA-recommended toner cartridge, you can utilize the following three functions of this equipment:
Cartridge detecting function:
This function checks if the toner cartridge is correctly installed and notifies you if it is not.
Toner remaining check function:
This function notifies you when there is little toner remaining in the cartridge, as well as notifying
it to your authorized service representative automatically by the remote service.
16 TOSHIBA Quality Is Second to None
Image quality optimization function:
This function controls image quality according to the characteristics of the toner to be used and
enables you to print images of an optimal quality.
If you are using a toner cartridge other than the one we recommend, the equipment may not be
able to detect whether it is installed or not. Therefore, even if the toner cartridge is correctly
installed, the error message “Toner not recognized” appears on the LCD screen and printing
may not be performed. You may also not be able to utilize the image quality optimization function, the toner remaining check function and the remote service function notifying your authorized service representative automatically.
If you are using a toner cartridge other than the one we recommend, toner is not recognized. If
this is a problem for you, please contact your service representative. Remember you will not be
able to utilize the Toner remaining check function and Image quality optimization function as we
mentioned.
Supplies / Parts
Dependability
Genuine TOSHIBA supplies are subjected to the strictest of inspections so that every supply you
receive will perform at optimal levels.
High Productivity
Genuine TOSHIBA supplies are created to meet the demands of our competitive world and provide high-speed reliable copies when you need them.
Stable Image Quality
Genuine TOSHIBA supplies are designed to provide consistently stable image output.
Copier Friendly Supplies
Genuine TOSHIBA supplies are designed to help to keep the equipment and all its parts in trouble-free working order. Reduction of machine wear is due to TOSHIBA’s intimate knowledge of
the equipment’s characteristics ensuring the highest standard of care.
Perfectly Suited Supplies
From the beginning TOSHIBA supplies and machines were made for each other. Whenever
TOSHIBA designs a new machine, it also designs a new toner that is made just for that
machine. By using genuine TOSHIBA supplies with TOSHIBA equipment, you are guaranteed
optimum performance.
Toner
Optimum Image Quality
TOSHIBA toner is manufactured using ultra-fine quality materials under precisely controlled conditions to ensure that your TOSHIBA equipment will continually generate sharp high-quality
images.
Cost Advantage
Genuine TOSHIBA toner provides value. Only the proper amount of toner is used during the
reproduction process, thereby enabling the machine to continue to operate until all the toner has
been used. In this way you get the full value from each cartridge used.
TOSHIBA Quality Is Second to None 17
Environmental Harmony
Genuine TOSHIBA toner is manufactured with the environment in mind. We use embossed or
plastic labels for our toner cartridges making them fully recyclable. In addition, dust and ozone
levels have been reduced to improve the working environment.
User Friendly
Before approving our toners for sale, we test them to be sure that they pass the strictest of
health standards. This takes all the worry out of handling the toner.
General
Service and Support Benefits
TOSHIBA’s Service technicians are certified to keep your equipment performing at optimum levels. To ensure continuous image quality, utilize an authorized TOSHIBA Service provider to care
for and perform periodical maintenance on your equipment.
18 General Precautions
General Precautions
When installing or moving
Warning
y This equipment requires 220 to 240 V AC, 8 A 50/60 Hz electric power. For Saudi Arabia 100
V version, it requires 127 V AC, 12 A 50/60 Hz electric power.
Do not use a power supply with a voltage other than that specified.
Avoid multiple connections in the same outlet. This could cause a fire or give you an electric
shock. If you are considering increasing the number of outlets, contact an electrician.
y Always connect this equipment to an outlet with a ground connection to avoid the danger of
fire or electric shock in case of short-circuiting. Contact your service representative for the
details. Be sure to use a 3-conductor, grounded wall outlet.
In areas, where a 2-pin plug is used, the equipment must be grounded for safety. Never
ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.
y Plug the power cable securely into the outlet. If it is not plugged in properly, it could heat up
and cause a fire or give you an electric shock.
y Do not damage, break or attempt to repair the power cable.
The following things should not be done to the power cable.
- Twisting it
- Bending it
- Pulling it
- Placing anything on it
- Making it hot
- Situating it near radiators or other heat sources
This could cause a fire or give you an electric shock. If the power cable is damaged, contact
your service representative.
y Do not install the equipment by yourself or try to move it once it has been installed. This
could result in an injury or damage to the device. Contact your service representative if the
equipment needs to be installed or moved.
y Pull the plug out from the outlet more than once a year to clean around the prongs. Accumu-
lating dust and dirt could cause a fire due to the heat released by electric leakage.
General Precautions 19
Caution
y Avoid placing the equipment in a place unsuitable for its weight and also make sure the sur-
face is level.
Remember that if the equipment falls over, serious injuries could result.
Weight of the equipment: approx. 32.0 kg (for the EU), approx. 33.0 kg (except for the EU)
y Be sure to use the adjusters (safety stopper) to fix the equipment firmly to the floor after mov-
ing/installing it. Make certain that the equipment is steady. If it moves, it could fall over and
injure someone.
y When removing the plug from the outlet, do not pull the power cable. Always hold the plug
when removing it from the outlet. If the power cable is pulled, the wires may become broken
and this could cause a fire or give you an electric shock.
y Make sure that the ventilation holes are not blocked up.
If the temperature within the equipment becomes too high, a fire could result.
y When connecting the interface cable to the equipment, be sure to turn the power OFF. If the
power is not turned off, you could get an electric shock.
Other points
y The socket outlet shall be installed near the equipment and shall be easily accessible.
y Make sure that there is enough space around the system to facilitate changing of parts,
maintenance and clearing paper jams.
If there is insufficient space, some operations, such as bypass feeding, will become difficult
and the equipment could even break down.
To insure optimal operation, allow clearances of at least 80 cm on the right, and 10 cm on the
left and behind.
y Be sure to fix the power cable securely so that no one trips over it.
y Adverse environmental conditions may affect the safe operation and performance of the
equipment, and the equipment could break down.
- Avoid locations near windows or with exposure to direct sunlight.
- Avoid locations with drastic temperature fluctuations.
- Avoid too much dust.
- Avoid locations that suffer from vibration.
y Make sure that the air is able to flow freely and that there is sufficient ventilation.
With inadequate ventilation, the unpleasant odor released by the ozone will begin to dominate the atmosphere.
10 cm
80 cm
10 cm
20 General Precautions
y Use the antiskid devices to fix the equipment when the Paper Feed Pedestal is installed.
Under the Paper Feed Pedestal (optional), there are 4 antiskid devices and 2 stoppers to
prevent its falling. When moving this equipment, turn them in the direction of the arrows (see
the figures below) and raise them to release the equipment. After it has been moved, be sure
to turn them in the opposite direction and lower them to fix it back in place.
y Lock the casters to fix the Desk.
The Desk (optional) has casters underneath. Before moving the Desk, raise the caster lock
to release it. After moving the Desk, be sure to lower the lock to fix it in place.
Do not install the equipment by yourself or try to move it once it has been installed.
This could result in an injury or damage to the device. Contact your service representative if
the equipment needs to be installed or moved.
Adjusters Safety stoppers
General Precautions 21
When using the equipment
Warning
y Do not take off the cover of the equipment; otherwise you could be injured or get an electric
shock.
y Do not remove or connect the plug with wet hands, as this could give you an electric shock.
y Do not place any container with liquid (flower vases, coffee cups, etc.) on or near the equip-
ment. This could cause a fire or give you an electric shock.
y Keep paper clips and staples away from the air vent. If not, a fire could result or you could
get an electric shock.
y If the equipment becomes excessively hot, smoke comes out of it or there is an odd smell or
noise, proceed as follows.
Turn the power OFF and remove the plug from the outlet, then contact your service representative.
y If the equipment will not be used for more than one month, remove the plug from the outlet
for safety purposes during that time.
If an insulation failure occurs, this could cause a fire or give you an electric shock.
Caution
y Do not place heavy objects (4 kg or more) on the original glass and do not press on it with
force. Breaking the glass could cause personal injury.
y Do not place heavy objects (4 kg or more) on the equipment. If the objects fall off, this could
cause injury.
y Be careful not to let your fingers be caught when closing the drawer. This could injure you.
y Do not touch the fuser unit or the metal area around it. Since they are very hot, you could be
burned or the shock could cause you to get your hand injured in the machine.
y Be careful not to let your fingers be caught between the equipment and the side cover. This
could injure you.
y Do not touch the hinge (= a connecting part) on the rear side of the Reversing Automatic
Document Feeder (optional) / Automatic Document Feeder (optional). This could catch and
injure your fingers when you open or close the Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder (optional).
22 General Precautions
Position of Certification label, etc.
For EU
Except for EU
Identification label
Explanatory label
Warning label
Warning for high-temperature areas (fuser unit
)
Warning for high-temperature areas (ventilation holes
)
General Precautions 23
Other points
y Do not turn the power OFF with jammed paper left inside the equipment. This could cause
malfunctions when the main switch is turned ON next time.
y Be sure to turn the power OFF when leaving the office or if there is a power failure.
y Be careful because the paper exit area and paper just after exiting are hot.
y Do not place anything other than paper on the receiving tray. This could disturb a normal
operation and cause malfunctions.
y Do not touch the photoconductive drum surface or the transfer charger. This could cause
image problems.
y Do not open/close the covers and the bypass tray, or pull out the drawers during printing.
During maintenance or inspection
Warning
y Never attempt to repair, disassemble or modify the equipment by yourself. You could cause
a fire or get an electric shock.
Always contact your service representative for maintenance or repair of the internal parts of
the equipment.
y Do not let liquids such as water and oil get into the system when cleaning the floor. This
could cause a fire and give you an electric shock.
Caution
y Always keep the plug and outlet clean. Prevent them from accumulating dust and dirt. This
could cause a fire and give you an electric shock due to the heat released by electric leakage.
Other points
y Do not use such solvents as thinner or alcohol when cleaning the surface of the equipment.
- This could warp the shape of the surface or leave it discolored.
- When using a chemical cleaning pad to clean it, pay attention to any cautionary points.
When handling supplies
Warning
y Never attempt to incinerate toner cartridges. This could cause an explosion. Do not dispose
of used toner cartridges. Contact your service representative.
Other points
y Read the operator’s manual carefully to replace the toner cartridge using the correct proce-
dure. An improper procedure could cause toner leakage or scattering.
y Do not open the toner cartridge forcibly. This could cause toner leakage or scattering.
y Keep the toner cartridge out of the reach of children.
y If toner is spilt on your clothes, wash it off with cold water. Your clothes will be stained with
toner and it will not come out if you use warm water.
y If toner leaks from the toner cartridge, be careful not to inhale or touch it.
24 General Precautions
First-aid measures
If you inhale or touch toner, etc; carry out the following treatment.
y Inhalation: Remove from exposure area to fresh air immediately. Contact a physician if there is any
difficulty in breathing or other signs of distress.
y Skin Contact: Wash with soap and water. Wash clothing before reuse. If irritation occurs or is persis-
tent, seek medical attention.
y Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes. If irritation persists,
call a physician.
y Ingestion: Dilute stomach contents with several glasses of water.
Disclaimer Notice 25
Disclaimer Notice
The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC CORPORATION (including its employees, agents and sub-contractors) to any purchaser or user (‘User’)
of the e-STUDIO195/225/245, including its accessories, options and bundled software (‘Product’).
1. The exclusion and limitations of liability referred to in this notice shall be effective to the fullest extent permissible at law. For the avoidance of doubt, nothing in this notice shall be taken
to exclude or limit TOSHIBA TEC CORPORATION’s liability for death or personal injury
caused by TOSHIBA TEC CORPORATION’s negligence or TOSHIBA TEC CORPORATION’s fraudulent misrepresentation.
2. All warranties, conditions and other terms implied by law are, to the fullest extent permitted
by law, excluded and no such implied warranties are given or apply in relation to the Products.
3. TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or damage whatsoever caused by any of the following:
(a) use or handling of the Product otherwise than in accordance with the manuals, including
but not limited to Operator’s Manual, User’s Guide, and/or incorrect or careless handling or
use of the Product;
(b) any cause which prevents the Product from operating or functioning correctly which
arises from or is attributable to either acts, omissions, events or accidents beyond the reasonable control of TOSHIBA TEC CORPORATION including without limitation acts of God,
war, riot, civil commotion, malicious or deliberate damage, fire, flood, or storm, natural
calamity, earthquakes, abnormal voltage or other disasters;
(c) additions, modifications, disassembly, transportation, or repairs by any person other than
service technicians authorized by TOSHIBA TEC CORPORATION; or
(d) use of paper, supplies or parts other than those recommended by TOSHIBA TEC CORPORATION.
4. Subject to paragraph 1, TOSHIBA TEC CORPORATION shall not be liable to Customer for:
(a) loss of profits; loss of sales or turnover; loss of or damage to reputation; loss of production; loss of anticipated savings; loss of goodwill or business opportunities; loss of customers; loss of, or loss of use of, any software or data; loss under or in relation to any contract;
or
(b) any special, incidental, consequential or indirect loss or damage, costs, expenses, financial loss or claims for consequential compensation;
whatsoever and howsoever caused which arise out of or in connection with the Product or
the use or handling of the Product even if TOSHIBA TEC CORPORATION is advised of the
possibility of such damages.
TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or damage caused by any inability to use (including, but not limited to failure, malfunction, hang-up,
virus infection or other problems) which arises from use of the Product with hardware, goods
or software which TOSHIBA TEC CORPORATION has not directly or indirectly supplied.
26 Environmental Information
Environmental Information
ENERGY STAR® Program
Toshiba Tec Corporation, as a member of the ENERGY STAR Program, attaches the ENERGY
STAR logo to all products which meet the ENERGY STAR Program requirements.
The ENERGY STAR Program aims at the promotion of the development and wider usage of
office equipment including energy-efficient computers in order to address environmental issues
such as global warming. Manufacturers that participate in this program can attach the ENERGY
STAR logo to products after confirming that they meet the energy saving standards of this program. Also, these standards and logo are commonly used within the U.S. Environmental Protection Agency (EPA) and participating countries.
Specified products, sales countries or regions may not be included.
To distinguish whether or not the product meets the ENERGY STAR Program requirements,
check if the corresponding logo is on the product.
If you have any questions, contact your service representative.
Turkey RoHS Compliance
Energy saving features
Energy saving features are provided in this product in order to reduce power consumption when
it is not being used.
Low power mode
The equipment automatically enters this mode when a specified period of time*1 has passed
since the last use. “Saving energy” appears on the LCD screen.
Sleep mode / Super sleep mode
The equipment automatically enters this mode when a specified period of time*1 has passed
since the last use.
*2, *3
In the sleep mode, “Sleep mode” appears on the LCD screen. In the
super sleep mode, the LCD screen is blank.
*1 The time until entering the low power mode and sleep mode / super sleep mode can be changed.
P.129 “Timer Setting”
*2 For the conditions needed to cancel the sleep mode / super sleep mode, see the following page:
P.37 “Canceling conditions for energy saving mode”
*3 When the Network Printer Kit GA-1192 (optional) is installed, the super sleep mode is disabled.
EEE Yönetmeliğine Uygundur.
1.PREPARATION
This chapter describes what you need to know before using this equipment, such as how to turn the power
ON or how to set copy paper.
Description of Each Component ...........................................................................28
Front / Right side...............................................................................................................................28
Left side / Inner side..........................................................................................................................29
Configuration of options ....................................................................................................................31
Control panel.....................................................................................................................................32
“Copy mode” main screen.................................................................................................................35
Preparation 1 - Turning Power ON.........................................................................36
Turning power ON.............................................................................................................................36
Saving energy when not in use - Energy saving mode -...................................................................37
Preparation 2 - Placing Copy Paper......................................................................39
Acceptable media types ....................................................................................................................39
Recommended paper........................................................................................................................40
Placing paper in drawers...................................................................................................................41
Placing paper in the drawers of Paper Feed Pedestal (optional) ......................................................45
Preparation 3 - Registering Size of Paper Placed................................................49
Registering standard size (A3, A4, A4-R, A5-R, B4).........................................................................49
Registering other standard sizes.......................................................................................................50
1 PREPARATION
28 Description of Each Component
Description of Each Component
Front / Right side
1. Platen Cover (optional, KA-1640PC)
Place an original on the original glass and start copying with this cover closed.
2. Reversing Automatic Document Feeder (optional, MR-3023) / Automatic Document
Feeder (optional, MR-2020)
A stack of originals placed on this are scanned one sheet after another. Maximum 100
sheets (or stack height 16 mm) of originals can be placed in one go. (The maximum number
of sheets can be placed may vary depending on the media type of the originals.) 2-sided
originals can be scanned with the Reversing Automatic Document Feeder (MR-3023).
P.58 “Placing originals on Reversing Automatic Document Feeder (optional) / Automatic
Document Feeder (optional)”
P.176 “Paper Jams”
3. Operator’s Manual Pocket (Back side) (optional, KK-1660)
Keep the Operator’s Manual in this.
4. Side cover
5. Automatic Duplexing Unit (optional, MD-0103)
Install this to make it possible to print on both sides of paper.
6. Bypass tray
Use this to make copies on special media types such as thick paper, overhead transparencies or tracing paper.
P.63 “Using Bypass Tray”
P.176 “Paper Jams”
2
1
3
4
5
6
7
8
9
10
11
12
13
Description of Each Component 29
7. Paper feed cover (Upper: Paper Feed Unit / Lower: Paper Feed Pedestal)
8. Paper size indicator
9. Drawer Module (optional, MY-1028)
Use this to add one more drawer to the Paper Feed Pedestal (optional, KD-1022). The max-
imum 550 sheets of plain paper (80 g/m
2
) can be placed at once.
10. Paper Feed Pedestal (optional, KD-1022)
Use this to add one more drawer to the equipment. Moreover, the Drawer Module (MY-1028)
(9) can add another drawer to it. In one drawer, the maximum 550 sheets of plain paper (80
g/m2) can be placed at once.
11. Paper Feed Unit (optional, MY-1038)
Use this to add one more drawer to the equipment. A maximum of 250 sheets of plain paper
can be placed in one go.
12. Drawer
Maximum 250 sheets of plain paper can be placed in one go.
13. Front cover
Open this cover when you replace the toner cartridge.
P.190 “Replacing Toner Cartridge”
Left side / Inner side
12
11
10
9
8
7
6
5
1
2
3
4
1 PREPARATION
30 Description of Each Component
1. Original glass
Use this to copy three-dimensional originals, book-type originals and special paper such as
overhead transparencies or tracing paper, as well as plain paper.
P.54 “Placing Originals”
2. Control panel
Use this to perform copying, key in the copy quantity, or set other functions.
P.32 “Control panel”
3. External Keyboard (optional, GJ-1160)
Use this when using the optional scanning and Fax functions to select destinations.
4. Toner cartridge
P.15 “Recommended toner cartridges”
P.190 “Replacing Toner Cartridge”
5. Power switch
Turn the power of the equipment ON or OFF with this.
P.36 “Preparation 1 - Turning Power ON”
6. Paper exit stopper
Use this to prevent the exiting paper from falling. Open this when you make a large amount
of copies on a larger size of paper (e.g. A3, B4).
7. AC-IN terminal
Use this to connect the co-packed power cable and the equipment.
8. USB terminal (4-pin)
With this terminal, the equipment can be connected to your PC using a commercially available USB cable.
y Use a USB2.0 Hi-Speed certified cable: USB cable supporting the USB2.0 Hi-Speed
mode (480 Mbps of transfer speed) certified by the USB Implementers Forum.
y Connect the equipment with a PC directly by the USB cable. When it is connected with a
PC via a USB hub, the equipment may not be recognized.
9. Receiving tray
10. Scanning area
The data of originals transported from the Reversing Automatic Document Feeder (optional,
MR-3023)/Automatic Document Feeder (optional, MR-2020) are scanned here.
P.204 “Daily Inspection”
11. Original scale
Use this to check the size of an original placed on the original glass.
12. Platen sheet
P.204 “Daily Inspection”
Description of Each Component 31
Configuration of options
The options listed below are available. Contact your service technician or service representative
for the details.
Other options
P3fax+ocr (GB-1292): Fax transmission/reception and OCR can be performed directly from a
PC to which the equipment is connected with a USB cable.
*1, *2
*1 The Fax Kit GD-1221 (optional) is necessary.
*2 This is not available in equipment in which the Network Printer Kit GA-1192 (optional) is installed.
Desk
(
MH-1640
)
Platen Cover
(
KA-1640PC
)
External Keyboard
(
GJ-1160
)
Fax Kit
(
GD-1221EU
)
Paper Feed Unit
(
MY-1038
)
Paper Feed Pedestal
(KD-1022)
Reversing Automatic Document Feeder
(
MR-3023
)
Automatic Document Feeder (MR-2020
)
Automatic Duplexing Unit
(
MD-0103
)
Main body
Drawer Module
(
MY-1028
)
Network Printer Kit
(
GA-1192
)
Scanner Upgrade Kit
(
GA-1202
)
Operator's Manual Pocket
(
Back side) (KK-1660
)
1 PREPARATION
32 Description of Each Component
Control panel
1. APS/AMS selecting button/lamps
Automatic paper selection (APS): The equipment detects the size of original and automat-
ically selects the same size of copy paper.
P.69 “Paper Selection”
Automatic magnification selection (AMS): Set the size of copy paper to be used in
advance. The equipment then detects the size of original and automatically selects the most
suitable reproduction ratio to the copy paper.
P.74 “Automatic magnification selection (AMS):”
2. [MIXED SIZE] button/lamp
Use this to copy originals whose sizes are different.
For the details of the mixed-size copying, see the following page:
P.72 “Copying Different Sizes in One Go - MIXED-SIZE COPYING -”
3. [ENERGY SAVER] button
Use this to let the equipment enter into the energy saving mode when the equipment is not
used.
For the details of the energy saving mode, see the following page:
P.37 “Saving energy when not in use - Energy saving mode -”
4. [INTERRUPT] button
Use this to interrupt the copy job in process and perform another one (= interrupt copying).
For the details of interrupt copying, see the following page:
P.62 “Interrupting copying and making another copy - Interrupt copy -”
5. [USER FUNCTIONS] button
Use this to change the equipment’s default settings.
For the details of default setting change, see the following page:
P.117 “CHANGING EQUIPMENT’S SETTINGS”
2789
22
1 10 11
15202425 23
1312
1418 16171921
4 563
Description of Each Component 33
6. [SETTINGS] button
Use this to confirm the copying functions currently set.
P.68 “Confirming set functions”
7. Selecting buttons (Left, Center, Right)
Use them to select items or operation in each menu. Items or operation corresponding to
each button appears at the lower section of the LCD screen.
e.g.) “Copy mode” main screen
P.35 ““Copy mode” main screen”
8. LCD screen
Use this to check each menu and error messages displayed on it.
P.35 ““Copy mode” main screen”
9. Digital keys
Use them to key in any number such as copy quantity.
10. FAX TX/RX lamp
This lamp blinks at the transmission and reception of Fax data.
11. Function switching buttons
Use them to switch functions among copying, printing, scanning and Fax.
To utilize the scanning functions, the Scanner Upgrade Kit (optional) is required.
To utilize the Fax functions, the Fax Kit (optional) is required.
12. [FUNCTION CLEAR] button/lamp
This lamp blinks when copying is finished. Use this button to clear the set copy functions.
13. Contrast adjustment volume
Use this to adjust the brightness level of the LCD screen (8).
14. [CLEAR/STOP] button
Use this to stop the copy job in process or return the copy quantity keyed in to “1”.
15. [START] button
Use this to start copying. Copies can be made when the lamp is lit. It blinks when the equipment is waiting for copying to be started.
For basic copy operations, see the following page:
P.59 “Making Copies”
READY
1
100% NONSORT
ZOOM FINISHING EDIT
Selecting buttons
1 PREPARATION
34 Description of Each Component
16. Alarm lamp
This lamp blinks when an error such as paper jams or running out of toner has occurred.
P.174 “When This Message Appears”
17. [DATA] lamp
This lamp blinks while print data or Fax are being received.
18. [CANCEL] button
Use this to cancel the current setting and return to the previous menu.
19. [ENTER] button
Use this to determine items or operation selected in each menu.
20. / / / (UP/DOWN/LEFT/RIGHT) buttons
Use them to select items you want to set in each menu. The selected item is highlighted.
21. Original mode button/lamps
Use this button to set the image quality of copy according to that of an original.
For the details of image quality, see the following page:
P.78 “Selecting Image Mode”
22. Density adjustment buttons/lamps
Use this button to adjust the density of copy image. The [AUTO] lamp below the
(automatic copy density mode) button is lit when the density is being automatically adjusted.
For the details of density adjustment, see the following page:
P.79 “Adjusting Density Level”
23. [DRAWER] button/lamps
Use this button to select a drawer or the bypass tray to be used as a paper source. The lamp
of the paper source currently selected is lit. The lamp blinks when the selected drawer or tray
is running out of paper.
When paper in the drawer or on the bypass tray has run out, see the following page to add
paper:
P.39 “Preparation 2 - Placing Copy Paper”
24. [COPY] button/lamps
Use this button to select the size of paper to be used. The lamp of the paper size currently
selected blinks when this size of paper is not placed in the drawer or on the bypass tray.
See the following page for details:
P.70 “Manual paper selection”
25. [ORIGINAL] button/lamps
Use this button to specify the size of an original.
P.76 “Specifying both the sizes of the original and the copy paper”
Description of Each Component 35
“Copy mode” main screen
After the power of the equipment is turned ON and the warm-up is finished, the display below is
shown on the LCD screen. This display is called the “copy mode” main screen.
This “copy mode” main screen appears by default after turning the power ON. You can display
the main screen for the Fax function or the scanning function instead of the “copy mode” main
screen by changing the default setting.
P.127 “Walkup Screen Setting”
1. Message area
This area displays the current status of this equipment or error messages.
2. Copy quantity
3. Reproduction ratio
4. Selecting button display
This area displays operation corresponding to each selecting button.
ZOOM: Use this to specify the reproduction ratio manually.
P.77 “Specifying reproduction ratio manually”
Custom mode: Use this to recall the copying function registered as a custom function. You
can quickly recall functions frequently used by registering it on the custom mode.
P.157 “Menu Customize”
EDIT: This area displays the copy menu. Use this to recall the desired copying function.
P.82 “Copy Menu”
5. Custom mode setting
This area displays the current setting of the function which has been registered as custom
function.
12
35
4
READY
1
100% NONSORT
ZOOM FINISHING EDIT
1 PREPARATION
36 Preparation 1 - Turning Power ON
Preparation 1 - Turning Power ON
Turning power ON
1
Press the power switch to “ ” (ON) side.
The equipment starts warming itself up. The warm-up time takes approx. 25 seconds.
When the warm-up has finished, the equipment is ready for copying. “READY” appears
on the LCD screen.
If you press the [START] button with an original placed while the warm-up is still continuing, copying automatically starts after it has finished. This is called auto job start. When
the job is reserved, “Auto Start” appears on the LCD screen to show you the current status.
However, this function cannot be accessed while “Please wait” is being displayed
(approx. 15 seconds).
2
The LCD screen below is shown if the equipment is managed under
the department code function. Key in the department code.
Key in a 5-digit department code, and then press the [ENTER] button. Then the
equipment is ready for copying.
If the department code function is enabled, press the [FUNCTION CLEAR] button after
any operation has been finished to prevent unauthorized use of the equipment.
For the details of the department code, see the following page:
P.143 “Department Code”
READY
1
100% NONSORT
ZOOM FINISHING EDIT
Enter DEPARTMENT CODE
1
100% NONSORT
Z
OOMINISHING
EDIT
Preparation 1 - Turning Power ON 37
Turning power OFF
Press the power switch to “ ” (OFF) side.
Saving energy when not in use - Energy saving mode -
To reduce power consumption, the equipment automatically enters into the energy saving mode
when a specified period of time has passed since its last use. You can also turn the equipment
into this mode manually.
Types of energy saving mode
There are two types of the energy saving mode as follows.
Sleep mode: The power consumption is 18 W. “Sleep mode” appears on the LCD screen, and
only the [ENERGY SAVER] lamp is lit.
Super sleep mode: The power consumption is 4 W. The LCD screen is blank, and only the
[ENERGY SAVER] lamp is lit.
y Either the sleep mode or the super sleep mode is enabled. The enabled mode and the time
until the mode is entered (Auto sleep time) can be changed.
P.134 “Energy Saving Mode Setting”
y When the Network Printer Kit GA-1192 (optional) is installed, the super sleep mode is dis-
abled.
y There is another one called the low power mode. Since the time until the low power mode is
entered (Auto low power time) and the time until the energy saving mode is entered (Auto
sleep time) work simultaneously, if auto sleep time is set shorter than auto low power time,
the equipment enters into the energy saving mode, but not into the low power mode.
P.26 “Energy saving features”
To turn the equipment into the energy saving mode manually
Check that the equipment is in the ready status, and press the [ENERGY SAVER] button.
The equipment is now in the energy saving mode. The [ENERGY SAVER] lamp is lit.
Canceling conditions for energy saving mode
The energy saving mode is canceled under the following conditions. After the warm-up has been
completed, the equipment goes into the ready status.
1 PREPARATION
38 Preparation 1 - Turning Power ON
Sleep mode
y When any of the [ENERGY SAVER] button, the [START] button and the function switching
buttons on the control panel is pressed
y When this equipment is connected to a PC with a USB cable
y When printing is performed from a PC connected with this equipment
y When the Weekly Timer reaches the time for the power to be turned ON
y When Fax data are received
y When the Platen Cover (optional) or the Automatic Document Feeder / Reversing Automatic
Document Feeder (optional) is raised
y When originals are placed on the Automatic Document Feeder / Reversing Automatic Docu-
ment Feeder (optional)
Super sleep mode
y When the [ENERGY SAVER] button on the control panel is pressed
y When this equipment is connected to a PC with a USB cable
y When printing is performed from a PC connected with this equipment
y When Fax data are received
y When the Platen Cover (optional) or the Automatic Document Feeder / Reversing Automatic
Document Feeder (optional) is raised
Preparation 2 - Placing Copy Paper 39
Preparation 2 - Placing Copy Paper
Place copy paper in an appropriate paper source before you start copying.
Acceptable media types
Acceptable media types differ depending on its paper source. See the table below for the details.
*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended
paper is used. See the following page for the TOSHIBA-recommended paper:
P.40 “Recommended paper”
*2 The paper of 50 to 63 g/m
2
can be used if it is set on the bypass tray one by one.
*3 Automatic duplex copying is not available.
*4 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other
than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.
*5 13"LG size paper can be used only in equipment for the EU.
y You cannot mix various paper sizes in one drawer.
y “LT format” is the standard size for only use in North America.
Abbreviations for LT format sizes:
LT: Letter, LD: Ledger, LG: Legal, ST: Statement, COMP: Computer
Feeder Media type Paper size
Maximum sheet
capacity
*1
Drawers of
the equipment and
Paper Feed
Unit
(optional)
Plain paper
(64 - 80 g/m
2
)
A/B format:
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT f o r m at:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
*5
250 sheets
(64 g/m
2
)
250 sheets
(80 g/m
2
)
Drawers of
the Paper
Feed Pedestal
(optional)
Plain paper
(64 - 80 g/m
2
)
A/B format:
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT f o r m at:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
*5
550 sheets
(64 g/m
2
)
550 sheets
(80 g/m
2
)
Bypass tray Plain paper
64 - 80 g/m
2)*2
A/B format:
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT f o r m at:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
*5
100 sheets
(64 g/m
2
)
100 sheets
(80 g/m
2
)
THICK PAPER 1
(81 - 105 g/m
2)*3
1 sheet
(81 - 105 g/m
2
)
THICK PAPER 2
(106 - 163 g/m
2)*3
1 sheet
(106 - 163 g/m
2
)
Tracing paper
(75 g/m
2)*3
1 sheet
Sticker labels
*3
1 sheet
Transparencies
*3, *4
A4 only
1 sheet
1 PREPARATION
40 Preparation 2 - Placing Copy Paper
Recommended paper
To ensure the best copy performance, TOSHIBA recommends the paper types listed below. If
you want to use paper other than that we recommend, contact your service technician.
*1 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other
than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.
Paper types not acceptable
Do not use the types of paper listed below since they may cause paper jams.
y Damp paper
y Creased paper
y Wrinkled paper or paper prone to be curled
y Paper whose surface is extremely smooth or rough
Do not use the types of paper listed below since they may cause an equipment malfunction.
y Paper whose surface is specially treated
y Paper once printed with other copiers or printers
Storing paper
Observe the following cautions when storing copy paper:
y Wrap copy paper in its wrapping paper to prevent it from gathering dust.
y Do not expose copy paper to direct sunlight.
y Store copy paper in a damp-free place.
y Store copy paper on a flat surface to prevent it from being creased or bent.
Media type Product name
Plain paper TGIS Paper / Mondi
80 g/m
2
THICK PAPER 1 Color Copy / Mondi
90 g/m
2
Color Copy / Mondi
100 g/m
2
THICK PAPER 2 Color Copy / Mondi
120 g/m
2
Color Copy / Mondi
160 g/m
2
Tracing paper Tracing paper / Ostrich International
75 g/m
2
only
Sticker labels 3478 / Zweckform-Avery
Transparencies
*1
PP2500 / 3M
Preparation 2 - Placing Copy Paper 41
Placing paper in drawers
Follow the procedure below to place copy paper in the drawer.
For the acceptable paper, see the following page:
P.39 “Acceptable media types”
1
Turn the power of the equipment ON.
2
Pull out the drawer carefully.
Pull out the drawer until it comes to a stop.
3
Press down the paper plate.
Press it down until you hear a click sound and it is no longer lifted up.
1 PREPARATION
42 Preparation 2 - Placing Copy Paper
4
Place paper in the drawer.
y The maximum number of sheets that can be placed at one time is 250 (64 to 80
g/m
2
). Be sure that the stack height of paper is not higher than the line indicated at
the inner side of the side guide and trailing guide.
P.39 “Acceptable media types”
y Fan the paper well before placing it in the drawer, otherwise multiple feeding could
occur. Be careful that the paper does not cut your fingers.
y Place the paper face up. You may tell its “face” by the note on its wrapping paper.
y Do not allow any gap between the paper and the right side wall in the drawer.
When placing LD size paper
To place LD size paper in the drawer, the end guide needs to be removed. Move it to
the left end while pushing its lower part from both sides, and then pull it upward. Keep
it in the pocket on the front side of the drawer.
3
2
1
Preparation 2 - Placing Copy Paper 43
5
Move the end guide to the trailing edge of the paper while pushing
its lower part in the direction of the arrows.
Do not allow any gap between the paper and the end guide in the drawer.
6
While holding the green lever of the front side guide, adjust the side
guides to the paper size.
7
Adjust the side guides to the desired paper size.
Be sure that a gap of approx. 0.5 mm (less than 1.0 mm in total) is left between the paper
and each side guide (shown as “A” in the picture). If the gap is inappropriate, this could
cause a paper misfeed.
A
1 PREPARATION
44 Preparation 2 - Placing Copy Paper
8
Change the paper size indicator to match the size of paper placed.
9
Push the drawer straight into the equipment slowly until it comes to
a stop.
Do not let your fingers be caught when closing the drawer.
This could cause injury.
Register the paper size into the equipment.
When you place paper, register the size of the paper into the equipment. Be sure that the
size is registered correctly, or it could cause a paper jam.
For the registration of paper size, see the following page:
P.49 “Preparation 3 - Registering Size of Paper Placed”
Be sure to register the paper size when you have changed the paper size in the drawer,
as well as when you place paper in the corresponding drawer for the first time.
The registration menu for the paper size can be displayed automatically whenever the
drawer is closed. This is useful when paper in the drawer is often replaced.
P.167 “Pop-Up Display Setting”
Preparation 2 - Placing Copy Paper 45
Placing paper in the drawers of Paper Feed Pedestal (optional)
Follow the procedure below to place copy paper in the drawers of the Paper Feed Pedestal
(optional).
For the acceptable paper, see the following page:
P.39 “Acceptable media types”
1
Pull out the drawer carefully.
Pull out the drawer until it comes to a stop.
2
Pull out the trailing guide while pushing its lower part to the direction of the arrow. Then reinstall the guide at the position of the
desired paper size.
The paper size is indicated on the bottom inner surface of the drawer.
1 PREPARATION
46 Preparation 2 - Placing Copy Paper
3
Push the right side of the side guide lock to unlock it.
4
While pushing the green knob of the side guides, adjust the side
guides at the position of the desired paper size.
Adjust the side guides with both hands.
5
Place paper in the drawer.
y The maximum number of sheets that can be placed at one time is 550 (80 g/m2). Be
sure that the stack height of paper is not higher than the line indicated at the inner
side of the guide.
P.39 “Acceptable media types”
y Fan the paper well before placing it in the drawer, otherwise multiple feeding could
occur. Be careful that the paper does not cut your fingers.
y Place the paper face up. You may tell its “face” by the note on its wrapping paper.
Preparation 2 - Placing Copy Paper 47
6
Adjust the side guides.
Be sure that a gap of approx. 0.5 mm (less than 1.0 mm in total) is left between the paper
and each side guide (shown as “A” in the picture). If the gap is inappropriate, this could
cause a paper misfeed.
7
Push the left side of the side guide lock to lock it.
8
Change the paper size indicator to match the size of paper placed.
A
1 PREPARATION
48 Preparation 2 - Placing Copy Paper
9
Push the drawer straight until it comes to a stop.
Do not let your fingers be caught when closing the drawer.
This could cause injury.
Register the paper size into the equipment.
When you place paper, register the size of the paper into the equipment. Be sure that the
size is registered correctly, or it could cause a paper jam.
For the registration of paper size, see the following page:
P.49 “Preparation 3 - Registering Size of Paper Placed”
Be sure to register the paper size when you have changed the paper size in the drawer,
as well as when you place paper in the corresponding drawer for the first time.
The registration menu for the paper size can be displayed automatically whenever the
drawer is closed. This is useful when paper in the drawer is often replaced.
P.167 “Pop-Up Display Setting”
Preparation 3 - Registering Size of Paper Placed 49
Preparation 3 - Registering Size of Paper Placed
When you place paper in a drawer for the first time or when you place paper whose size is different from that of the paper which has been placed in the drawer, the new paper size needs to be
registered into the equipment.
Registration of standard sizes (A3, A4, A4-R, A5-R, B4) differs from that of standard sizes other
than these.
y The paper size can also be registered on the “user functions mode” main screen.
P.125 “Paper Size Setting”
y The registration menu for the paper size can be displayed automatically whenever the
drawer is closed. This is useful when paper in the drawer is often replaced.
P.167 “Pop-Up Display Setting”
Registering standard size (A3, A4, A4-R, A5-R, B4)
In this section, A4 size is registered in the drawer of the equipment as an example.
1
Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.
The LCD screen shows as follows:
2
Press the [DRAWER] button several times until the lamp of the
drawer in which you placed paper is lit.
Select paper size
1
100% NONSORT
Z
OOMINISHING
EDIT
1 PREPARATION
50 Preparation 3 - Registering Size of Paper Placed
3
Press the [COPY] button several times until the lamp of the paper
size you placed in the drawer is lit.
If the [CANCEL] button is pressed at this step, the size is not registered and the
equipment will return to its normal status.
4
Press the [ENTER] button.
The paper size has been registered.
Registering other standard sizes
When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register this size as
“OTHER” size.
In this section, LT size is registered in the drawer of the equipment as an example.
1
Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.
The LCD screen shows as follows:
Select paper size
1
100% NONSORT
Z
OOMINISHING
EDIT
Preparation 3 - Registering Size of Paper Placed 51
2
Press the [DRAWER] button several times until the lamp of the
drawer in which you placed paper is lit.
3
Press the [COPY] button several times until the [OTHER] lamp is lit.
4
Press the selecting buttons (Center, Right) to select the size of the
paper placed in the drawer. This can also be done with the or
button.
e.g.) Setting LT size
5
Press the [ENTER] button.
The LCD screen shows as follows:
6
Press the [ENTER] button.
The paper size has been registered as “OTHER” size and the equipment will return to its
normal status.
Select paper size
LT-R
LG
LT
Select paper size
1
100% NONSORT
Z
OOMINISHING
EDIT
2.HOW TO MAKE COPIES
This chapter describes basic copy operations.
Placing Originals.....................................................................................................54
Acceptable originals ..........................................................................................................................54
Placing originals on the original glass ...............................................................................................55
Placing booklet-type originals such as books or catalogues.............................................................56
Using Reversing Automatic Document Feeder (optional) / Automatic Document Feeder (optional) 57
Placing originals on Reversing Automatic Document Feeder (optional) / Automatic Document Feeder
(optional) ...........................................................................................................................................58
Making Copies.........................................................................................................59
Stopping/Resuming copying..............................................................................................................61
Interrupting copying and making another copy - Interrupt copy - ......................................................62
Using Bypass Tray..................................................................................................63
Bypass copying.................................................................................................................................64
2 HOW TO MAKE COPIES
54 Placing Originals
Placing Originals
Acceptable originals
Booklets, three-dimensional objects and some types of special media can be placed on the original glass, as well as plain paper. When the Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional) is used, a stack of plain paper originals can be automatically scanned one by one.
*1 The automatic size detection function is not enabled for LT format.
*2 “Special media types” refers to special paper which is not acceptable for the Reversing Automatic Docu-
ment Feeder (optional) / Automatic Document Feeder (optional), such as overhead transparencies or
tracing paper.
*3 Do not place heavy objects (4 kg or more) and do not press on it with force.
*4 The size of FOLIO originals can be detected automatically only when they are placed on the Reversing
Automatic Document Feeder (optional).
*5 Their paper weight should be between 50 g/m
2
and 127 g/m2 (in both cases of 1-sided and 2-sided).
*6 Some media types may not be used.
*7 A5 size originals must be placed in a landscape direction.
Maximum number of originals scanned in one go
Up to 250 original sheets can be scanned at one time. When the number of sheets to be
scanned exceeds 250 or the built-in memory in the equipment becomes full during the scanning
of the copy job, scanning stops and “Count over” or “Memory is full” appears on the LCD screen.
To copy the data scanned so far, select “Print”. To delete them, select “Cancel job”.
In the following cases, only data deletion is possible. After doing this, perform copying again with
the original divided.
y When sort copying for one set is performed
y When the magazine sort mode is selected
y When non-sort copying is performed (only when the number of sheets to be scanned
exceeds 250)
Setting position
Type of origi-
nals
Maximum
size
Acceptable sizes for auto-
matic size detection
*1
Remarks
Original glass Plain paper
Special media
types
*2
Booklets
3-dimensional
objects
297 mm x 432 mmA3, A4, A4-R, A5-R, B4, B5,
B5-R
*3
Reversing Automatic Document
Feeder (optional) /
Automatic Document Feeder
(optional)
Plain paper A3, A4, A4-R, A5-R, B4, B5,
B5-R, FOLIO
*4, *5, *6, *7
Placing Originals 55
Placing originals on the original glass
Plain paper or some special media types which are not acceptable for the Reversing Automatic
Document Feeder (optional) / Automatic Document Feeder (optional), such as overhead transparencies or tracing paper, should be placed on the original glass.
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
1
Raise the Platen Cover (optional) or the Reversing Automatic Document Feeder (optional) / Automatic Document Feeder (optional).
Raise the Platen Cover (optional) or the Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder (optional) 60 degrees or more from the equipment to detect the original size.
2
Place the original face down on the original glass and align it
against the left rear corner of the glass.
When copying highly transparent originals
When copying highly transparent originals such as overhead transparencies or tracing
paper, place a blank sheet of paper (A), the same size as the original or larger, over the
original (B).
B
A
2 HOW TO MAKE COPIES
56 Placing Originals
3
Lower the Platen Cover (optional) or the Reversing Automatic Document Feeder (optional) / Automatic Document Feeder (optional)
carefully.
Placing booklet-type originals such as books or catalogues
Place a book-type original on the original glass.
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
1
Raise the Platen Cover (optional) or the Reversing Automatic Document Feeder (optional) / Automatic Document Feeder (optional).
2
Open the desired page of the original and place it face down.
Align it against the left rear corner of the glass.
3
Lower the Platen Cover (optional) or the Reversing Automatic Document Feeder (optional) / Automatic Document Feeder (optional)
carefully.
y Do not try to lower the Platen Cover (optional) or the Reversing Automatic Document
Feeder (optional) / Automatic Document Feeder (optional) forcibly when the original
is very thick. There will be no problem in copying even if they are not fully lowered.
y Do not look fully at the original glass since intensive light may leak out during copy-
ing.
Placing Originals 57
Using Reversing Automatic Document Feeder (optional) / Automatic
Document Feeder (optional)
When a stack of originals are placed on the Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional), the originals are automatically scanned one by one. The
following types of originals are available
*1
:
*1 To scan 2-sided originals, the Reversing Automatic Document Feeder (optional) is required.
y Some media types may not be used.
y The maximum number of sheets acceptable varies depending on the media types of the
originals.
y A5 size originals must be placed in a landscape direction.
y Sizes which the Reversing Automatic Document Feeder (optional) / Automatic Document
Feeder (optional) can detect automatically are A3, A4, A4-R, A5-R, B4, B5, B5-R and
FOLIO. (The size of FOLIO originals can be detected automatically only when they are
placed on the Reversing Automatic Document Feeder (optional).)
Precautions for Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder (optional)
Do not use the following types of original since such types may cause a paper jam or damage to
the equipment:
y Extremely wrinkled, folded or curled ones
y Ones with carbon paper
y Taped, pasted or cut-out ones
y Clipped or stapled ones
y Ones with holes or tears
y Damp ones
y Overhead transparencies or tracing paper
y Coating paper (e.g. coated with wax)
y Ones with many holes punched (e.g. loose leaf paper)
The following types of originals are usable but need extra care:
y Ones which cannot be made to slide with the fingers or whose surface is specially treated
(they may not be able to be separated from each other at feeding)
y Folded or curled ones (should be smoothed out before being used)
When black streaks appear on the copied image
If the scanning area or the guide area is dirty, image problems such as black streaks on the copied image may occur. Weekly cleaning of these areas is recommended.
P.204 “Daily Inspection”
Media types Maximum size
Maximum number of
sheets acceptable
Paper weight
Plain paper 297 mm x 432 mm 100 sheets
(or stack height 16 mm)
50 - 127 g/m
2
2 HOW TO MAKE COPIES
58 Placing Originals
Placing originals on Reversing Automatic Document Feeder (optional)
/ Automatic Document Feeder (optional)
1
Align all the originals.
2
Place them face up and align the side guides to the original length.
y The top sheet of the originals will be scanned first.
y The total sheets of originals placed must not exceed 100 (50 to 80 g/m
2
) or the stack
height of the originals must not exceed 16 mm regardless of their sizes.
When placing a large amount of originals with a long width
Pull out the original stopper so that the exiting originals will not fall. When replacing this
stopper, lift it slightly and push it in.
Making Copies 59
Making Copies
Follow the procedure below to make copies.
Various copying functions are available. See the following page for the details:
P.67 “COPYING FUNCTIONS”
P.81 “ADVANCED COPYING FUNCTIONS”
1
Check if paper is placed in the drawer.
For the acceptable types and sizes of paper, see the following pages:
P.39 “Acceptable media types”
P.41 “Placing paper in drawers”
P.45 “Placing paper in the drawers of Paper Feed Pedestal (optional)”
2
Place the original.
For acceptable originals or how to place originals, see the following pages:
P.54 “Acceptable originals”
P.58 “Placing originals on Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional)”
P.55 “Placing originals on the original glass”
P.56 “Placing booklet-type originals such as books or catalogues”
3
Key in the desired number of copies (= copy quantity) when you
copy more than one set.
e.g.) 5 sets
If you want to correct the copy quantity keyed in, press the [CLEAR/STOP] button, and
then key in the correct number.
4
Select the copy modes as required.
P.67 “COPYING FUNCTIONS”
P.81 “ADVANCED COPYING FUNCTIONS”
Some functions may not be used together with other functions. For the details, see the
following page.
P.215 “Copying Function Combination Matrix”
5
Press the [START] button.
Copying starts. The paper will exit with its copied side down.
5
100% NONSORT
ZOOM FINISHING EDIT
READY
2 HOW TO MAKE COPIES
60 Making Copies
The paper exit area and exiting paper are hot immediately after the exit. Handle them
with care.
When “Next original?” appears
This message appears when “SORT” is selected for the exiting method while an original is being
placed on the original glass, or when 2-sided copying is being performed.
Place the next original on the original glass, and then press the [START] or [ENTER] button. The
data of the next original will be scanned. When all the originals have been scanned, select “NO”,
and then press the [START] or [ENTER] button. Copying starts.
When the number of sheets exiting has exceeded 250
To prevent exiting paper from falling off the receiving tray, the equipment causes copying to
pause when approx. 250 sheets of paper have been continuously exited. The LCD screen
shows as follows:
Remove the paper from the receiving tray, and then press the [START] button. Copying
resumes.
Press the [CLEAR/STOP] button to end the copy job. “Memory clear?” appears on the LCD
screen. Select “YES”, and then press the [START] or [ENTER] button.
When the paper has run out
When the paper in the drawer has run out during copying, if paper whose size and direction are
the same is in another drawer, it is automatically fed and copying continues to be performed. If
not, copying stops and the following message appears on the LCD screen.
e.g.) Paper in the drawer of the equipment has run out
The [DRAWER] lamp corresponding to the one whose paper has run out blinks.
Add paper to the drawer and press the [START] button. Copying then resumes.
Next original?
YES
NO
Clear paper output tray:
PRESS START KEY.
DRAWER1 empty
Open DRAWER1
Load paper
Close DRAWER1
Making Copies 61
Stopping/Resuming copying
Press the [CLEAR/STOP] button to stop scanning or copying.
1
Press the [CLEAR/STOP] button during scanning or copying.
Scanning or copying stops, and the LCD screen shows as follows:
Or
Press the selecting button (Right) or and buttons and select “YES” to end the
copy job. Then press the [START] or [ENTER] button.
2
Press the selecting button (Right) to select “NO” to resume the
copy job. This can also be done with the or button. Then
press the [START] or [ENTER] button.
The LCD screen shows as follows:
3
Press the [START] button.
Memory clear?
YES
NO
Cancel job?
YES
NO
Press START to resume
3
100% NONSORT
Z
OOMINISHING
EDIT
2 HOW TO MAKE COPIES
62 Making Copies
Interrupting copying and making another copy - Interrupt copy -
You can interrupt copying of one job and make another copy job (= interrupt copying). The copy
quantity or functions applied to the interrupted job are stored in the memory of this equipment,
so that you will not need to set them again when the interrupted job resumes.
1
Press the [INTERRUPT] button.
The [INTERRUPT] lamp blinks, and the lamp will be fully lit after a while.
The LCD screen shows as follows:
When the [INTERRUPT] button is pressed during scanning, the [INTERRUPT] lamp
blinks, and then the lamp will be fully lit after the scanning has finished.
2
Replace the original with a new one.
3
Select the copy modes as required, and then press the [START]
button.
Interrupt copying starts.
4
After you have finished interrupt copying, press the [INTERRUPT]
button.
“Ready to resume job” appears, and then the copying status returns to the one before the
interruption.
Even if you do not press the [INTERRUPT] button, a certain time after the interrupt copying has finished, the auto clear function will work and the interrupt mode will automatically be cleared.
5
Press the [START] button.
The job interrupted will resume.
1
100% NONSORT
ZOOM FINISHING EDIT
Job interrupted
Using Bypass Tray 63
Using Bypass Tray
Place paper on the bypass tray when you use the following media types as copy paper:
y Thick paper (81 to 163 g/m
2
)
y Special media types such as tracing paper, sticker labels or overhead transparencies
y Standard size paper which cannot be placed in the drawers of the equipment and Paper
Feed Unit (optional) (e.g. A5-R)
Using the bypass tray is recommended also for copying on standard-size paper other than those
placed in the drawers. The following sizes are available for bypass copying:
*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended
paper is used. See the following page for the TOSHIBA-recommended paper:
P.40 “Recommended paper”
*2 The paper of 50 to 63 g/m
2
can be used if it is set on the bypass tray one by one.
*3 Automatic duplex copying is not available.
*4 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other
than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.
*5 13"LG size paper can be used only in equipment for the EU.
Media type Paper size
Maximum sheet
capacity
*1
Plain paper
(64 - 80 g/m
2)*2
A/B format:
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT format:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
*5
100 sheets (64 g/m2)
100 sheets (80 g/m
2
)
THICK PAPER 1
(81 - 105 g/m
2)*3
1 sheet
(81 - 105 g/m
2
)
THICK PAPER 2
(106 - 163 g/m
2)*3
1 sheet
(106 - 163 g/m
2
)
Tracing paper
(75 g/m
2)*3
1 sheet
Sticker labels
*3
1 sheet
Transparencies
*3, *4
A4 only
1 sheet
2 HOW TO MAKE COPIES
64 Using Bypass Tray
Bypass copying
In this section, the procedure is described with A4 size paper placed on the bypass tray as an
example.
1
Place paper straight on the bypass tray face down. Then align the
side guides to the paper length while holding (A).
y Up to 100 sheets of plain paper (64 to 80 g/m2) can be set. In this case, make sure
that the height of the paper stack does not exceed the indicators of the side guides. If
paper other than plain is used, set it one sheet at a time.
y Fan the stack of paper well before placing it on the bypass tray.
y Do not push the paper forcibly into the entrance of the bypass feeder. This could
cause a paper misfeed.
When you place paper of a larger size, pull out the paper holder before you start bypass
copying.
A
Using Bypass Tray 65
2
Check the menu.
If the paper size has already been registered, the following menu is displayed.
In this case, proceed to step 5.
If the paper size has not been registered, the following menu is displayed.
In this case, proceed to step 3.
3
Set the paper size.
Press the selecting buttons (Center, Right) to select the size of paper placed in the
drawer. This can also be done with the or button. Then press the [ENTER] button.
e.g.) Setting A4 size
When the paper is other than standard sizes, select “NON_SIZE”.
4
Set the paper type.
Press the selecting button (Right) to select paper type. This can also be done with the
or button. Then press the [ENTER] button.
e.g.) Thick paper (81 to 105 g/m
2
)
You can select the media type from the following four:
THICK PAPER 1: Thick paper (81 to 105 g/m
2
)
THICK PAPER 2: Thick paper (106 to 163 g/m
2
), sticker labels
TRANSPARENCY: Overhead transparencies
PLAIN: Plain paper (64 to 80 g/m
2
), tracing paper
If you select a different media type from the one you placed on the bypass tray, this could
cause a paper jam or the quality of the copied image could be lowered.
1
100% SORT
ZOOM FINISHING EDIT
Ready for bypass
Select paper size
NON_SIZE
COMP
13LG
Select paper size
A4
ST-R
A3
PAPER TYPE THICK PAPER1
THICK PAPER2
TRANSPARENCY
2 HOW TO MAKE COPIES
66 Using Bypass Tray
5
Place the original.
6
Select the other copy modes as required, and then press the
[START] button.
Copying starts.
When you make copies on overhead transparencies using the bypass tray, pick up the
transparencies which have exited onto the receiving tray one by one. If the transparencies pile up, they may become curled and not be good for projection.
When the paper on the bypass tray has run out during copying, copying continues with
the paper of the same size in the drawer as the one on the bypass tray. (If the size of the
paper on the bypass tray has not been registered in advance, however, copying stops. In
this case, add paper to the bypass tray and press the [START] button to resume copying.)
When bypass copying has finished
If the paper on the bypass tray has been removed or used up, bypass feeding will be automatically switched to drawer feeding. The paper size setting for the bypass tray will also be cleared.
3.COPYING FUNCTIONS
This chapter describes various functions related to copy operations, such as how to make enlargement or
reduction copies, or how to adjust the quality of copy images.
Before Making Copies ............................................................................................68
Default settings .................................................................................................................................68
Confirming set functions....................................................................................................................68
Paper Selection.......................................................................................................69
Automatic paper selection (APS) ......................................................................................................69
Manual paper selection.....................................................................................................................70
Copying Different Sizes in One Go - MIXED-SIZE COPYING -............................72
Zooming In/Out Copy Image..................................................................................74
Automatic magnification selection (AMS)..........................................................................................74
Specifying both the sizes of the original and the copy paper ............................................................76
Specifying reproduction ratio manually .............................................................................................77
Selecting Image Mode ............................................................................................78
Adjusting Density Level .........................................................................................79
3 COPYING FUNCTIONS
68 Before Making Copies
Before Making Copies
Default settings
Initial settings established when the equipment is powered on before any of the user functions
are changed are called default settings. Each setting returns to its default when the power is
turned ON, when the energy saving mode is canceled, and when the [FUNCTION CLEAR] button is pressed.
The default settings of the basic copying functions at the time of the installation are shown
below.
The default settings above can be changed. For the details, see the following page:
P.117 “CHANGING EQUIPMENT’S SETTINGS”
Confirming set functions
Press the [SETTINGS] button to confirm the set functions.
The current settings and functions set appear on the LCD screen.
Press the selecting buttons (Center, Right) to display all the settings so that the display will be
switched to the next one. This can also be done with the or button. After you finished the
confirmation, press the [SETTINGS] button again.
Item Contents Default setting at installation
Copy quantity 1 - 999 1
Paper selection Automatic paper selection (APS), Man-
ual paper selection
Automatic paper selection (APS)
Reproduction ratio 25 - 200% 100%
Image mode TEXT/PHOTO, PHOTO, TEXT TEXT/PHOTO
Density adjustment Automatic copy density mode, Manual
copy density mode
Automatic copy density mode
NONSORT
2IN1 1>1 SIMPLEX
Paper Selection 69
Paper Selection
You can select the size of copy paper in two ways; one is automatic paper selection in which the
equipment automatically selects copy paper of the same size as the original, and the other is
manual paper selection in which you can select the desired paper size manually.
Automatic paper selection (APS):
The equipment detects the size of the original placed and automatically selects copy paper of
the same size as the original.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
Manual paper selection:
You can select the desired size of copy paper manually. This function can be used in a case the
APS cannot be used, such as when originals are non-standard sizes or overhead transparencies.
Automatic paper selection (APS)
When you place a standard size original, the equipment detects its size and automatically
selects copy paper of the same size as the original.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
The equipment may not be able to correctly detect the size of the originals listed below. Use
manual paper selection for the following originals:
y Highly transparent ones (e.g. overhead transparencies, tracing paper)
y Wholly dark ones or ones with dark borders
y Non-standard size ones (e.g. newspapers, magazines)
P.70 “Manual paper selection”
1
Place paper in the drawer.
Register the size of the paper into the equipment in advance.
P.49 “Preparation 3 - Registering Size of Paper Placed”
2
Place the original.
3 COPYING FUNCTIONS
70 Paper Selection
3
Press the APS/AMS selecting button and select APS. (The APS
lamp is lit.)
y The default setting at the installation is APS.
y If the direction of paper in the drawer differs from that of originals, the image of the
original can be copied being rotated by 90 degrees, as long as their sizes are the
same (B5 and A4 only).
4
Select the other copy modes as required, and then press the
[START] button.
Manual paper selection
Select the paper size with this method when you use the following originals whose sizes may not
be detected correctly with automatic paper selection:
y Highly transparent ones (e.g. overhead transparencies, tracing paper)
y Wholly dark ones or ones with dark borders
y Non-standard size (e.g. newspapers, magazines)
In this method, if the desired size of copy paper is not placed in the drawer, replace the paper
already placed in the drawer with the desired one, or place the desired size of paper on the
bypass tray.
P.41 “Placing paper in drawers”
P.63 “Using Bypass Tray”
1
Place paper in the drawer.
2
Place the original.
Paper Selection 71
3
Press the [DRAWER] button several times until the lamp of the
desired drawer is lit.
e.g.) Selecting the drawer of the equipment
4
Select the other copy modes as required, and then press the
[START] button.
3 COPYING FUNCTIONS
72 Copying Different Sizes in One Go - MIXED-SIZE COPYING -
Copying Different Sizes in One Go - MIXED-SIZE COPYING -
When different sizes of originals are mixed and placed on the Reversing Automatic Document
Feeder (optional), some combinations of sizes can be copied in one go. The combination of A3
and A4, B4 and B5, or A4-R and FOLIO is available.
1
Place paper in the drawer.
Bypass copying is disabled. Place paper in the drawer.
2
Place originals on the Reversing Automatic Document Feeder
(optional).
3
Press the [MIXED SIZE] button.
The mixed-size copying mode is set and the [MIXED SIZE] lamp is lit.
The equipment is switched to the automatic paper selection mode and the [APS] lamp is
lit. When copying in the automatic paper selection mode, step 4 is not necessary. In this
case, proceed to step 5.
In the automatic paper selection mode, a copy is made on copy paper of the same size
as the original. Place paper whose sizes are the same as those of the originals in the corresponding drawers in advance.
Copying Different Sizes in One Go - MIXED-SIZE COPYING - 73
4
If you want to copy all the originals on the same size paper, press
the [DRAWER] button to select the drawer.
e.g.) Selecting the drawer of the equipment
5
Select the other copy modes as required, and then press the
[START] button.
Copying starts.
When “Change direction ORG” appears
The originals are not placed in a correct direction. Press the [ENTER] button to exit the
original. Then place it by rotating 90 degrees and resume copying.
When the copying has finished, press the [FUNCTION CLEAR] button.
3 COPYING FUNCTIONS
74 Zooming In/Out Copy Image
Zooming In/Out Copy Image
You can set the reproduction ratio of the copy image in the following three ways:
Automatic magnification selection (AMS):
Specify the size of the copy paper in advance. As the original is placed, the equipment then
detects the size of the original and sets the reproduction ratio most suited to the size of copy
paper automatically.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
Specifying both the sizes of the original and the copy paper:
When you specify the sizes of both the original and the copy paper, the equipment automatically
sets the reproduction ratio most suited to both of these sizes. This function can be used in case
the AMS cannot be used, such as when originals are overhead transparencies.
Specifying reproduction ratio manually:
Specify the reproduction ratio manually from 25% to 200%.
The reproduction ratio can be set in the horizontal and vertical direction separately. In this case,
select XY zoom function in the copy menu.
P.111 “Changing Sizes in Horizontal and Vertical Directions - XY ZOOM -”
Automatic magnification selection (AMS)
Specify the copy paper size to be used in advance. The equipment then detects the size of the
original and automatically sets the most suitable reproduction ratio for the size of copy paper, as
the original is placed.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
Automatic magnification selection (AMS) may not work correctly for the size of originals listed
below. Use other methods to set the reproduction ratio for the following originals:
y Highly transparent ones (e.g. overhead transparencies, tracing paper)
y Wholly dark ones or ones with dark borders
y Non-standard size (e.g. newspapers, magazines)
Zooming In/Out Copy Image 75
1
Place paper in the drawer.
2
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
e.g.) Selecting A4 size
You can select the desired paper size with the [DRAWER] button in the same procedure.
3
Press the APS/AMS selecting button until the AMS lamp is lit.
The reproduction ratio on the “copy mode” main screen will be changed to “AMS”.
4
Place the original.
5
Select the other copy modes as required, and then press the
[START] button.
Copying is performed with the most suitable reproduction ratio for the specified paper
size.
When “Change direction ORG” appears
The direction of the original placed is not correct. Press the [ENTER] button to exit the original.
Then place it by rotating 90 degrees and resume copying.
3 COPYING FUNCTIONS
76 Zooming In/Out Copy Image
Specifying both the sizes of the original and the copy paper
1
Place paper in the drawer.
2
Place the original.
3
Press the [ORIGINAL] button several times until the lamp of the
desired original size is lit.
e.g.) Selecting B4 for the original
4
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
e.g.) Selecting A4 for copy paper
y You can select the desired paper size with the [DRAWER] button in the same proce-
dure.
y When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register
this size as “OTHER” size in advance.
P.50 “Registering other standard sizes”
The most appropriate reproduction ratio for both the sizes of the original and the copy
paper is set.
5
Select the other copy modes as required, and then press the
[START] button.
Zooming In/Out Copy Image 77
Specifying reproduction ratio manually
1
Place paper in the drawer.
2
Place the original.
3
Press the selecting button (Left).
The LCD screen shows as follows:
4
Press the selecting button (Center: – or Right: +) to set the desired
reproduction ratio.
One press of each button increases or decreases the reproduction ratio by 1%. When
you keep pressing either of them, the reproduction ratio also keeps changing. The
reproduction ratio can be set from 25% to 200%.
Press the selecting button (Left) to return it to 100%.
5
Press the [ENTER] button.
The reproduction ratio is set.
6
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
e.g.) Selecting A4 for copy paper
y You can select the desired paper size with the [DRAWER] button in the same proce-
dure.
y When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register
this size as “OTHER” size in advance.
P.50 “Registering other standard sizes”
7
Select the other copy modes as required, and then press the
[START] button.
ZOOM
100%
+-100%
25% ---- 200%
3 COPYING FUNCTIONS
78 Selecting Image Mode
Selecting Image Mode
You can select the most suitable quality of the copied image in the following three modes
depending on the originals:
TEXT/PHOTO: Originals with text and photographs mixed
PHOTO: Originals with photographs
TEXT: Originals with text only or with text and fine illustrations only
“TEXT/PHOTO” is set by default at the installation of the equipment.
1
Place paper in the drawer.
2
Place the original.
3
Press the original mode button until the lamp of the desired mode
is lit.
e.g.) Original with photographs
4
Select the other copy modes as required, and then press the
[START] button.
Adjusting Density Level 79
Adjusting Density Level
The automatic copy density mode, which automatically selects the most suitable density level for
the copied image by detecting that of the original, is set by default at the installation of the equipment. You can also adjust the density level as desired manually (=manual copy density mode) in
the following procedure:
1
Place paper in the drawer.
2
Place the original.
3
Press the density adjustment buttons ( (light) or (dark))
to adjust the density to the desired level.
The density level can be set within 7 stages. One press of each button increases or
decreases the density level by one stage. When you keep pressing either of them, the
density level also keeps changing.
4
Select the other copy modes as required, and then press the
[START] button.
To return it to the automatic copy density mode
Press the (AUTO) button.
4.ADVANCED COPYING FUNCTIONS
This chapter describes some useful copying functions, such as how to copy more than one page into a single
sheet of paper or how to print date and time on copy paper.
Copy Menu...............................................................................................................82
Copying in Same Page Order as Originals - Sort Copying -...............................84
Sorting Alternately One Set by One - ALTERNATION - .......................................85
Sorting in Magazine Type Arrangement - MAGAZINE SORT -............................86
Shifting Paper to Make Margin - IMAGE SHIFT -..................................................88
Erasing Shadow on Edge - EDGE ERASE -..........................................................90
Copying on Both Sides - DUPLEX - ......................................................................92
Copying Right and Left Pages Separately - DUAL PAGE - .................................99
Printing Page Number, Date and Time - ANNOTATION - ...................................101
Changing Copy Setting on Each Job - JOB BUILD - .........................................103
Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 -..................................................105
Copying Both Sides of Card into 1 Page - ID CARD -........................................108
Changing Sizes in Horizontal and Vertical Directions - XY ZOOM -................. 111
Registering Functions Frequently Used - JOB MEMORY - ............................... 113
4 ADVANCED COPYING FUNCTIONS
82 Copy Menu
Copy Menu
This equipment provides you of many convenient copying functions. When you press the selecting button (Right) on the “copy mode” main screen, the copy menu appears. Select the desired
function in this menu.
More than one copying function can be used together. However, some combinations of functions
are disabled. For the details of the disabled combinations, see the following page:
P.215 “Copying Function Combination Matrix”
Operating in copy menu
When you select the desired function in the menu, press , , and buttons or
the selecting buttons (Left, Center, Right). In this section, the procedure for selecting the XY
zoom function using the selecting buttons (Left, Center, Right) is explained as an example.
1
Select the column, in which the desired function is located, with the
selecting buttons (Left, Center, Right).
e.g.) Press the selecting button (Right) to select “XY ZOOM”.
2
Press the same selecting button for several times until you select
the desired function.
3
Press the [ENTER] button.
The function setting screen appears. Perform the setting by following the instructions
displayed on the screen.
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
Left Center Right
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
Copy Menu 83
Copy function list
The copying functions displayed on the copy menu are shown below.
Function Description
FINISHING
( P.84, P.85,
P.86)
Selects finishing modes for paper copied and exited to the receiving tray.
SORT: Exited in the same order as originals in each set.
NONSORT: Exited without being sorted.
ALTERNATION: Exited while they are being sorted and rotated alternately one
set by one.
MAGAZINE SORT: Exited in a booklet-type page arrangement.
IMAGE SHIFT
( P.88)
Makes a binding margin on copy paper. The margin width can be set between 4
mm and 15 mm.
LEFT MARGIN: Makes a binding margin on the left side of paper.
RIGHT MARGIN: Makes a binding margin on the right side of paper.
EDGE ERASE
( P.90)
Makes a margin along the edge of copy paper. The margin width can be set
between 4 mm and 15 mm.
PAPER TYPE
( P.63)
Selects the media type of copy paper. This function is available only in the
bypass copying.
THICK PAPER1: Thick paper 1 (81 - 105 g/m
2
)
THICK PAPER2: Thick paper 2 (106 - 163 g/m
2
), sticker labels
TRANSPARENCY: Overhead transparencies
PLAIN: Plain paper (64 - 80 g/m
2
), tracing paper
DUPLEX
( P.92)
Selects whether originals and copy paper are 1-sided or 2-sided.
1>1 SIMPLEX: 1-sided original to 1-sided copy
1>2 DUPLEX: 1-sided original to 2-sided copy
2>2 DUPLEX: 2-sided original to 2-sided copy
2>1 SPLIT: 2-sided original to 1-sided copy
BOOK > 2: Booklet-type original to 2-sided copy
DUAL PAGE
( P.99)
Makes copies of the double-page spread of a booklet. The right and left pages
are copied separately. The book margin width can be set between 8 mm to 30
mm.
ANNOTATION
( P.101)
Prints page numbers, date and time.
PAG E N U M BER: Prints page numbers.
Page, Date&Time: Print page numbers, date and time.
JOB BUILD
( P.103)
Scans and copies originals made of several jobs (= stacks). Settings and scanning methods can be changed for each job. When all the originals have been
scanned, they are copied in one go.
2IN1/4IN1
( P.105)
Makes copies of 2 or 4 pages of originals into 1 page by reducing their reproduction ratio.
2IN1: Makes copies of 2 pages into 1 page.
4IN1: Makes copies of 4 pages into 1 page.
ID CARD
( P.108)
Makes copies of the both sides of a card into 1 page of A4 paper.
XY ZOOM
( P.111)
Selects the reproduction ratio in the horizontal and vertical directions separately.
JOB MEMORY
( P.113)
Registers the combination of functions used frequently and recall it as required.
RECALL: Recalls the combination of functions registered.
MEMORY: Registers the combination of functions.
4 ADVANCED COPYING FUNCTIONS
84 Copying in Same Page Order as Originals - Sort Copying -
Copying in Same Page Order as Originals - Sort Copying -
When you make several sets of copies, the copies can be made to exit in the same order as the
originals in each set. This is called sort copying.
1
Place paper in the drawer.
2
Place the original.
When originals are placed on the Reversing Automatic Document Feeder (optional), this
function is automatically set. In this case, proceed to step 5.
3
Select “FINISHING” in the copy menu, and then press the [ENTER]
button.
4
Select “SORT”, and then press the [ENTER] button.
The sort copying is set.
5
Select the other copy modes as required, and then press the
[START] button.
Copied and sorted in 2 sets
Copied in 2 sets without being sorted
1
2
3
1
2
3
1
2
3
1
2
3
1
1
2
2
3
3
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
FINISHING SORT
NONSORT
ALTERNATION
Sorting Alternately One Set by One - ALTERNATION - 85
Sorting Alternately One Set by One - ALTERNATION -
When you make several sets of copies, the copies can be sorted and made to exit alternately
one set by one. This is called alternation. You need to place copy paper in one drawer in a landscape direction and place that of the same size in another drawer in a portrait direction in
advance.
A4 or B5 size is available for this function.
1
Place paper in the drawer.
2
Place the original.
3
Key in the desired number of copies.
4
Select “FINISHING” in the copy menu, and then press the [ENTER]
button.
5
Select “ALTERNATION”, and then press the [ENTER] button.
The alternation is set.
6
Select the other copy modes as required, and then press the
[START] button.
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
FINISHING SORT
NONSORT
ALTERNATION
4 ADVANCED COPYING FUNCTIONS
86 Sorting in Magazine Type Arrangement - MAGAZINE SORT -
Sorting in Magazine Type Arrangement - MAGAZINE SORT -
The copies can be made to exit in a booklet-type page arrangement. This is called magazine
sort. You can make a booklet by folding and binding the stack of copied paper at its center.
y A3, A4-R, A5-R, B4 and B5-R sizes are available for this function.
y The Automatic Duplexing Unit (optional) is required.
y This function cannot be used together with the image shift.
P.88 “Shifting Paper to Make Margin - IMAGE SHIFT -”
1
Place paper in the drawer.
2
Place the original.
3
Select “FINISHING” in the copy menu, and then press the [ENTER]
button.
4
Select “MAGAZINE SORT”, and then press the [ENTER] button or
button.
10 3
85
1
2
3
12
12 1
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
FINISHING NONSORT
ALTERNATION
MAGAZINE SORT
Sorting in Magazine Type Arrangement - MAGAZINE SORT - 87
5
Select the duplex copying mode most suited to the original, and
then press the [ENTER] button.
1>2: When originals are 1-sided
2>2: When originals are 2-sided
The magazine sort is set.
6
Select the other copy modes as required, and then press the
[START] button.
MAGAZINE SORT
1>2
2>2
4 ADVANCED COPYING FUNCTIONS
88 Shifting Paper to Make Margin - IMAGE SHIFT -
Shifting Paper to Make Margin - IMAGE SHIFT -
You can make a margin on copy paper by shifting the whole paper to the right or left. The margin
can be used for punching holes or stapling.
y When you place paper on the bypass tray, register the size of the paper into the equipment in
advance.
y This function cannot be used together with the magazine sort.
P.86 “Sorting in Magazine Type Arrangement - MAGAZINE SORT -”
1
Place paper in the drawer.
2
Place the original.
3
Select “IMAGE SHIFT” in the copy menu, and then press the
[ENTER] button.
4
Select whether you make a margin on the right or left side of the
paper, and then press the [ENTER] button or button.
LEFT MARGIN: The margin will be made on the left.
RIGHT MARGIN: The margin will be made on the right.
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
IMAGE SHIFT LEFT MARGIN
RIGHT MARGIN
OFF
Shifting Paper to Make Margin - IMAGE SHIFT - 89
5
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 4 mm and 15 mm.
The image shift is set.
6
Select the other copy modes as required, and then press the
[START] button.
RIGHT MARGIN
7mm
+-
4mm ---- 15mm
4 ADVANCED COPYING FUNCTIONS
90 Erasing Shadow on Edge - EDGE ERASE -
Erasing Shadow on Edge - EDGE ERASE -
When you make copies of thick objects such as books, the edge of copied image may be darkened by shadow. When you use this copied image as an original, you can erase this shadow
and make a margin only on the edge of paper with this function.
y Only standard size originals are available.
y When you place paper on the bypass tray, register the size of the paper into the equipment in
advance.
1
Place paper in the drawer.
2
Place the original.
3
Select “EDGE ERASE” in the copy menu, and then press the
[ENTER] button.
4
Select “ON”, and then press the [ENTER] button or button.
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
EDGE ERASE
ON
OFF
Erasing Shadow on Edge - EDGE ERASE - 91
5
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 4 mm and 15 mm.
The edge erase is set.
6
Select the other copy modes as required, and then press the
[START] button.
EDGE ERASE
7mm
+-
4mm ---- 15mm
4 ADVANCED COPYING FUNCTIONS
92 Copying on Both Sides - DUPLEX -
Copying on Both Sides - DUPLEX -
You can select whether originals and paper are 1-sided or 2-sided individually. You can make
copies of 1-sided originals into the both sides of paper so that you can save paper. Also you can
copy a book into the both sides of paper so that you can make another book.
1>1 SIMPLEX ( P.93)
2>1 SPLIT ( P.93)
1>2 DUPLEX ( P.94)
2>2 DUPLEX ( P.94)
Copying on Both Sides - DUPLEX - 93
BOOK > 2 ( P.96)
y To scan 2-sided originals automatically, the Reversing Automatic Document Feeder
(optional) is required.
y To copy on the both sides of paper, the Automatic Duplexing Unit (optional) is required.
Copying on one side
You can copy 1-sided or 2-sided originals on the one side of paper.
1
Place paper in the drawer.
2
Place the original.
3
Select “DUPLEX” in the copy menu, and then press the [ENTER]
button.
4
Select the duplex copying mode, and then press the [ENTER] button.
1>1 SIMPLEX: 1-sided original to 1-sided copy
2>1 SPLIT: 2-sided original to 1-sided copy
The mode of duplex copying is set.
-12-
-13-
-15-
-13-
-15-
-13-
-12-
-13-
-13-
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
DUPLEX
2>1 SPLIT
2>2 DUPLEX
BOOK > 2
4 ADVANCED COPYING FUNCTIONS
94 Copying on Both Sides - DUPLEX -
5
Select the other copy modes as required, and then press the
[START] button.
Copying starts.
6
Place the next original if you are using the original glass, select
“YES”, and then press the [ENTER] button. Repeat this procedure
until all the originals are scanned.
You can press the [START] button instead of selecting “YES”.
When all the originals have been scanned
Select “NO” and then press the [ENTER] button.
Copying on both sides
You can copy 1-sided or 2-sided originals on the both side of paper.
1
Place paper in the drawer.
Use plain paper (64 to 80 g/m2).
2
Place the original.
3
Select “DUPLEX” in the copy menu, and then press the [ENTER]
button.
Next original?
YES
NO
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
Copying on Both Sides - DUPLEX - 95
4
Select the duplex copying mode, and then press the [ENTER] button or button.
1>2 DUPLEX: 1-sided original to 2-sided copy
2>2 DUPLEX: 2-sided original to 2-sided copy
5
Select the finishing mode, and then press the [ENTER] button.
BOOK TYPE: Open to left
TABLET TYPE: Open to top
The mode of duplex copying is set.
6
Select the other copy modes as required, and then press the
[START] button.
Copying starts.
7
Place the next original if you are using the original glass, select
“YES”, and then press the [ENTER] button. Repeat this procedure
until all the originals are scanned.
You can press the [START] button instead of selecting “YES”.
When all the originals have been scanned
Select “NO” and then press the [ENTER] button.
DUPLEX
1>2 DUPLEX
1>1 SIMPLEX
2>2 DUPLEX
DUPLEX
BOOK TYPE
TABLET TYPE
Next original?
YES
NO
4 ADVANCED COPYING FUNCTIONS
96 Copying on Both Sides - DUPLEX -
Copying booklet on both sides
You can copy booklet-type originals such as books or catalogues on the both sides of paper, as
in the same manner as the original.
1
Place paper in the drawer.
y Use plain paper (64 to 80 g/m2).
y B5 and A4 sizes are available.
2
Press the [DRAWER] button to select the paper source to use.
3
Select “DUPLEX” in the copy menu, and then press the [ENTER]
button.
4
Select “BOOK > 2”, and then press the [ENTER] button or button.
PAPER TYPE
JOB BUILD
EDGE ERASE
ANNOTATION
IMAGE SHIFT
DUAL PAGE
FINISHING DUPLEX
JOB MEMORY
XY ZOOM
ID CARD
2IN1/4IN1
DUPLEX
2>1 SPLIT
2>2 DUPLEX
BOOK > 2
Copying on Both Sides - DUPLEX - 97
5
Select whether the beginning page of the copy is the right or left
page, and also select whether the ending page is the right or left
page. Then press the [ENTER] button or button.
Select among “RIGHT > RIGHT”, “RIGHT > LEFT”, “LEFT > LEFT” and “LEFT > RIGHT”.
e.g.) Copy begins with page 2 and ends with page 6: “LEFT > LEFT”
6
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 8 mm and 30 mm.
The mode of duplex copying is set.
BOOK > 2
RIGHT > LEFT
RIGHT > RIGHT
LEFT > LEFT
23 67
BOOK MARGIN
15mm
+-
8mm ---- 30mm
4 ADVANCED COPYING FUNCTIONS
98 Copying on Both Sides - DUPLEX -
7
Place the original, and then select other copy modes as required.
Then press the [START] button.
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
Scanning starts.
8
Open the next page and place the original, select “YES”, and then
press the [ENTER] button. Repeat this procedure until the last page
to be copied is left.
You can press the [START] button instead of selecting “YES”.
When copying the last page
If the last page is 1-sided, select “YES (SINGLE)” and then press the [ENTER] button. If
it is 2-sided, select “YES” and then press the [ENTER] button.
When all the originals have been scanned
Select “NO” and then press the [ENTER] button.
Next original?
YES
YES(SINGLE)
Loading...