Toshiba DST-3000 Owner’s Manual

Toshiba DST-3000 High Definition Digital Receiver

WordFinder, PrePick, MyLogos, AlphaJump, and BannerGuide are trademarks of Toshiba America

Consumer Products, Inc. TOSHIBA is a registered trademark of Toshiba Corporation. DIRECTV, the Cyclone Design logo, Advanced Program Guide, and DIRECTV PLUS are trademarks of DIRECTV, Inc. a unit of Hughes Electronics Corp., and are used with permission. DIRECT TICKET is a registered trademark of Hughes Communications, Inc. “NFL,” the NFL Shield and “NFL SUNDAY TICKET” are registered trademarks of The National Football League and its affiliates. “NHL” and the NHL Shield are registered trademarks of the National Hockey League. “NHL Center Ice” is a trademark of the National Hockey League. “MLB,” “MLB EXTRA INNINGS,” “Major League Baseball,” and the Major League Baseball silhouetted batter logo are service marks of Major League Baseball Properties, Inc. Major League Baseball trademarks and copyright are used with permission of Major League Baseball Properties, Inc. All other trademarks and service marks are the property of their respective owners.

This product is the subject of one or more U.S. or foreign patents pending.

Disclaimer—Every effort has been made to ensure the correctness and completeness of the material in this document. No company shall be liable for errors contained herein. The information in this document is subject to change without notice. No warranty of any kind is made with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

StarSight

Information—StarSight is a registered

trademark of StarSight Telecast, Inc. StarSight features are licensed under one or more of the following U.S. patents: 4,706,121; 5,151,789; 5,335,277; 5,353,121; 5,479,266; 5,479,268; and 5,532,754. Use rights reserved.

Macrovision

Information—Macrovision is a

registered trademark of Macrovision Corporation. This device incorporates an anticopy process technology that is protected by U.S. patents and other intellectual property rights. The anticopy process is licensed for noncommercial, home use only. Reverse engineering or disassembly is prohibited.

Information—Manufactured under license

Dolby

from Dolby Laboratories. “Dolby” and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corp. Confidential unpublished works. © 1992–2000 Dolby Laboratories. All rights reserved.

Note on Recording Programming—Most television programs and films are copyrighted. This

means that someone has legal rights governing the reproduction and distribution of this material. In certain circumstances, copyright law may apply to private in-home taping of copyrighted materials. In most cases, it is permissible to record for personal use, as long as you do not sell the material. You must act responsibly in this area—check into the matter if you are unsure.

Some pay per view programs may be licensed from producers as “view only” programs. These are copyrighted programs and may not be copied or reproduced for any purpose without the express written permission of the copyright owner.

DIRECTV

can only be received by U.S. residents and is not available outside the U.S. DIRECTV sold separately and independently of DIRECTV

Programming—DIRECTV® service

programming is

System hardware. Due to copyright restrictions, you may not be able to view some high definition programs in high definition format using this product. A valid programming subscription is required to operate DIRECTV

System hardware. For subscription information, or to resolve problems related to programming, call the service provider, DIRECTV, at 1-800DIRECTV (347-3288).

Satellite System Hardware and Installation—To arrange for professional installation of your satellite system, ask questions, or to resolve problems, please contact your dealer. For additional information, please visit our web site at www.toshiba.com/tacp

Toshiba Customer Solutions Center

1-888-867-4377

Subscriptions and pay per view

1-800-DIRECTV

PLEASE MAKE NOTE OF THE FOLLOWING

INFORMATION FOR WARRANTY

Receiver Model #: DST-3000

Receiver Serial #:________________________

Access Card #:________ ________ ________

Page ii

Important Safety Instructions

For your safety and protection, read this entire Owner’s Manual before you attempt to install or use your satellite system. In particular, read this safety section carefully. Keep this safety information where you can refer to it, if necessary.

Heed Cautions—All cautions on the product and in the operating instructions should be adhered to.

Follow Instructions—All operating and use instructions should be followed.

THESE CAUTIONS AND SYMBOLS APPEAR ON THE BACK OF THE DST-3000 RECEIVER

WARNING or CAUTION

Double insulated systems are protected by additional board clearances and creepage, so that the unit will not be a safety hazard to the end-user.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THESE ARE DEFINITIONS FOR ALERTS USED IN THIS MANUAL

WARNING or CAUTION

Where you see this alert symbol and the WARNING or CAUTION heading, strictly follow the warning instructions to avoid personal injury.

DANGER

Electric shock hazard: Where you see this symbol and the DANGER heading, strictly follow the warning instructions to avoid electric shock injury.

THESE ALERTS APPEAR IN THIS MANUAL

DANGER

To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.

flow to the unit. Blocking the airflow to the unit could impair performance or damage your receiver. Also do not stack the HD receiver on top of a “hot” component such as an audio power amplifier.

CAUTION

Do not stack electronic components or other objects on top of the HD receiver. The slots on top of the receiver must be left uncovered to allow proper air-

Page iii

Toshiba DST-3000 High Definition Digital Receiver

INSTALLATION

Polarization—This DST-3000 receiver is equipped with

a plug that will fit into the power outlet only one way. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. To prevent electric shock, do not use this plug with an extension cord or outlet unless you can fully insert the blades without blade exposure.

Power Sources—Operate this DST-3000 receiver only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

Power-Cord Protection—Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Ven tilati on—Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. Do not block any ventilation openings, install in accordance with the manufacturer’s instructions.

The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. Failure to follow these Ventilation instructions may cause the DST-3000 to overheat, which may degrade performance or result in property damage.

For electrical safety, power line operated equipment or accessories connected to this unit should bear the UL listing mark and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or fire. If in doubt, contact qualified service personnel.

Heat—Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Accessories—To avoid personal injury or damage to the DST-3000 receiver, do not place the DST-3000 receiver on any unstable cart, stand, table, or bracket. Any mounting of the product should follow the manufacturer’s instructions.

Attachments—Do not use attachments unless recommended by Toshiba as they may cause hazards.

Satellite Dish Antenna Grounding—The outdoor satellite dish antenna used to receive satellite signals and

the cable used to connect the satellite dish antenna to the indoor receiving unit are required to comply with local installation codes and the appropriate sections of the National Electric Code (NEC) and in particular Article 810–15, which covers proper installation and grounding of television receiving equipment, as well as to Article 820–33, which specifies that the satellite dish antenna cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. These codes require proper grounding of the metal structure of the outdoor satellite dish antenna and grounding of the connecting cable at a point where it enters the house (or other building). If you are having a professional installer make the installation, the installer must observe installation codes. This manual contains instructions on how to make the installation in compliance with the NEC. If additional local installation codes apply, contact local inspection authorities.

Ground

clamp

Electric

service

equipment

Ground

clamps

Coaxial cable

Grounding block

Coaxial cable

Grounding conductor

Power service grounding electrode

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO THE NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED IN “RADIO AND TELEVISION EQUIPMENT”

Note: The DST-3000 receiver shall be grounded through the satellite/local antenna cable before plugging into the telephone jack, and it must remain grounded thereafter.

Water and Moisture—Warning! To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Lightning—For added protection for this product, unplug this apparatus during lightning storms or when unused for long periods of time. Unplug it from the wall outlet, disconnect the antenna and cable system, and disconnect it from the telephone line. This will prevent damage to the product due to lightning and power line surges.

Television Antenna Information—Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer. Do not locate the outside antenna system in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, take extreme care to keep from touching such power lines or circuits, as contact with them might be fatal. If an outside antenna is connected to

Page iv

Installation

the DST-3000 receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the NEC, NFPA No. 70 1987, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of the grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Note to CATV System Installer—This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and particularly specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Power Lines—Extreme care must be taken when installing and adjusting or maintaining the outdoor

SERVICE

Servicing—Do not attempt to service this DST-3000

receiver yourself as opening or removing covers may expose you to dangerous voltage or other hazards. There are no user serviceable parts inside. Refer all servicing to qualified service personnel.

Conditions Requiring Service—Unplug the DST- 3000 receiver from the wall outlet and refer servicing to qualified personnel under the following conditions:

● When the power supply cord or plug is damaged.

● If liquid has been spilled on, or objects have fallen

into, the DST-3000 receiver or it has been exposed to water.

● If the DST-3000 receiver does not operate normally by

following the operating instructions. Adjust only those

antenna and connecting cable, especially in the vicinity of overhead power lines, electric lights, or power circuits. When installing the outdoor antenna or cable, extreme care should be taken to keep from touching or approaching such power lines or circuits, as contact with them might be fatal.

Cleaning—Unplug this DST-3000 receiver from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean only with dry cloth.

Object and Liquid Entry—Never push objects of any kind into this DST-3000 receiver through openings as they may touch dangerous voltages or short out parts that may result in property damage or electric shock. Never spill liquid of any kind on the DST-3000 receiver. No objects filled with liquids, such as vases, shall be placed on the apparatus.

controls that are covered by the operating instructions. Other adjustments may result in damage and will often require extensive work by a qualified technician to restore the DST-3000 receiver to its normal operation.

● If the DST-3000 receiver has been dropped or the cab-

inet has been damaged.

● When the DST-3000 receiver exhibits a distinct

change in performance.

Replacement Parts—When replacement parts are required, have the technician verify that the replacements being used have the same safety characteristics as the original parts. Use of replacement parts specified by the manufacturer can prevent fire, electric shock, or other hazards.

Page v

Toshiba DST-3000 High Definition Digital Receiver

Federal Communications Commission

(FCC) Regulatory Information

Federal Communications Commission (FCC)—

This equipment complies with both Part 15 and Part 68 of the FCC rules.

FCC Declaration of Conformity Compliance Statement

The Toshiba DST-3000 High Definition Digital Receiver complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation. The responsible party for compliance to these rules is as follows:

Toshiba America Consumer Products, Inc. 82 Totowa Rd. Wayne, NJ 07470

Ph: (888) 867-4377

Part 15 compliance—

Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving satellite dish

antenna.

● Increase the separation between the equipment and the

DST-3000 receiver.

● Connect the equipment into an outlet on a circuit dif-

ferent from that to which the DST-3000 receiver is connected.

● Consult the dealer or an experienced radio/TV techni-

cian for help.

The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio and TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC.

To meet FCC requirements, only peripherals (computer input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this device. Operation with noncertified peripherals is likely to result in interference to radio and TV reception.

Page vi

To meet FCC requirements, shielded cables are required to connect the device to a personal computer, peripheral, or other Class B certified device.

Part 68 compliance—

1) This equipment complies with Part 68 of the FCC rules. On the modem card is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be provided to the Telephone Company.

The REN is used to determine the quantity of devices which may be connected to the telephone line. An excessive number of REN’s on the line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the number of REN’s should not exceed five (5). To be certain of the number of devices that may be connected to the line, contact the Telephone Company to determine the maximum number of REN’s permitted for the calling area.

2) If the terminal equipment DST-3000 receiver causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice is not practical, the Telephone Company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC, if you believe it is necessary.

3) The Telephone Company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to make the necessary modifications in order to maintain interrupted service.

4) If trouble is experienced operating the DST-3000 receiver on the telephone network, please contact the Toshiba Customer Solutions Center at 1-888-867-4377 for further instructions.

● Toshiba America Consumer Products, Inc. must

make any necessary repairs to the modem portion of this equipment in order to maintain valid FCC registration. Do not attempt to repair or service the modem in the DST-3000 receiver.

● No repairs can be made by customers. All repairs

are to be performed by a Toshiba America Consumer Products, Inc. Authorized Service Station (TASS).

● This equipment cannot be used on public coin

service provided by the Telephone Company. Connection to Party Line Service is subject to state tariffs.

Table of Contents

Important Safety Instructions............................iii

Federal Communications Commission (FCC)

Regulatory Information............................vi

A First Look at the HD System........................1-1

What You Should Do First.........................1-1

How Does All This Work? .........................1-2

HD System Components ................................1-3

The DIRECTV PLUS™ Satellite Dish

Antenna.................................................1-3

The DST-3000 Receiver with DIRECTV

PLUS™ Receiver Built-in.....................1-4

The Remote Control ...............................1-6

Installing the Remote Control Batteries ....1-8

Setting Up Your Satellite Receiver ..................2-1

Choosing the Best Connection for Your

Entertainment System...........................2-2

HD Receiver and Satellite Dish

Antenna with Terrestrial Antenna

or Cable Service ...................................2-3

HD Receiver and HDTV Monitor..............2-4

HD Receiver with HDTV Monitor

and VCR................................................2-6

HD Receiver and Standard Definition

TV Monitor ...........................................2-8

HD Receiver with Standard Definition

TV Monitor and VCR............................2-9

HD Receiver and Dolby® Digital

Receiver or Decoder...........................2-12

HD Receiver and Standard Stereo

System .................................................2-13

Finishing Up............................................2-13

Connecting the VCR Control Cable.............2-14

Finding the VCR’s Remote Control

Sensor .................................................2-14

Now You Can Turn It On.............................2-14

POWER-ON Screen.................................2-15

Exit...........................................................2-15

Installation...............................................2-15

Controlling the DST-3000 Receiver.................3-1

Front Panel vs. Remote Control Keys............3-1

Basic Navigation ............................................3-1

Setting Up the Satellite Dish Antenna and

Terrestrial Inputs.................................... 4-1

Installing and Testing the Satellite

Dish Antenna........................................ 4-1

Displaying the INSTALLATION Screen...... 4-2

Selecting the Correct Type of

Satellite Dish Antenna.......................... 4-2

Dish Type Selections................................. 4-2

Finding the Correct Antenna-pointing

Coordinates .......................................... 4-3

Pointing the Dish Antenna........................ 4-4

Testing Signal Strength ............................. 4-4

System Test................................................ 4-4

Fine Tuning the Pointing of the Dish

Antenna ................................................ 4-5

Selecting Transponders............................. 4-6

Adding Terrestrial Antenna or Cable

to Your Satellite Connections .............. 4-6

Local In Connection Options .................... 4-7

Scan Channels........................................... 4-7

Local Providers......................................... 4-7

Local Provider Area Options.................... 4-7

Testing the Strength of the Terrestrial

Digital Channels .................................. 4-8

Terrestrial Antenna or Cable without

a Satellite Connection .......................... 4-9

Local In Connection Options .................... 4-9

Selecting the Correct Satellite Dish

Type for Terrestrial-only Operation .... 4-9

Scan Channels.........................................4-10

Editing Local Channels .......................... 4-10

Time Setup................................................... 4-10

Installation Is Now Complete...................... 4-10

Watching Local Terrestrial and DIRECTV

Programming .......................................... 5-1

Types of Channels ......................................... 5-1

DIRECTV

Local Channels from DIRECTV ............... 5-1

Digital (ATSC) Channels with Dish

Analog (NTSC) Channels with Dish

Digital (ATSC) Channels without Dish

Analog (NTSC) Channels without Dish

Programming ........................ 5-1

Connection ........................................... 5-1

Connection ........................................... 5-2

Page vii

Toshiba DST-3000 High Definition Digital Receiver

Basic Channel Changing ............................... 5-2

Channel Banner........................................ 5-2

The Information Banner ........................... 5-3

BannerGuide™......................................... 5-3

MyLogos™ ............................................... 5-3

AlphaJump™ ............................................ 5-4

Alternate Services.......................................... 5-4

Audio......................................................... 5-4

Closed Caption ......................................... 5-4

Advanced Program Guide™ ........................... 6-1

Program Guide............................................... 6-1

PROGRAM GUIDE Screen ...................... 6-1

PROGRAM GUIDE Pop-up Menu ........... 6-2

Choosing the Guide Style.......................... 6-2

Descriptions.............................................. 6-5

General On-Screen Guide Features ......... 6-6

Using the PrePick™ Feature from the

Advanced Program Guide™................ 6-6

Using the PrePick™ Feature

for Viewing........................................... 6-7

Canceling Scheduled Programs ............... 6-7

Filtering the Guides ....................................... 6-7

Theme Filters ............................................ 6-7

Channel List.............................................. 6-8

Guide Times .............................................. 6-8

The INFORMATION Screen........................ 6-9

Done.......................................................... 6-9

Show Times............................................... 6-9

SHOW TIMES Screen ............................... 6-9

Done.......................................................... 6-9

Video ......................................................... 6-9

Guides ....................................................... 6-9

PrePick™ ............................................... 6-10

WORDFINDER™....................................... 6-10

WORDFINDER™ Entry......................... 6-11

DST-3000 Receiver’s Menu System................ 7-1

Menu Overview......................................... 7-1

Main Menu .................................................... 7-2

Guide......................................................... 7-2

Video ......................................................... 7-2

Setup Menu ....................................................7-2

Done .......................................................... 7-2

Video .........................................................7-2

Preferences.....................................................7-3

Done .......................................................... 7-3

Video .........................................................7-3

Advanced...................................................7-3

Preference Options ...................................7-3

Channel Tags ............................................7-3

Scheme ...................................................... 7-3

Filters ........................................................ 7-4

Translucency .............................................7-4

Advanced Preferences.................................... 7-4

Done .......................................................... 7-4

Video .........................................................7-4

Advanced Preference Options...................7-4

Receiver ID ...............................................7-4

Channel Lock ............................................7-5

Factory Defaults .......................................7-5

Audio/Video Setup ........................................7-5

Audio .........................................................7-5

Dolby Digital............................................. 7-5

Closed Caption..........................................7-5

TV Resolution............................................7-6

Screen Ratio ..............................................7-6

Image Shape ..............................................7-6

Limits ............................................................. 7-7

Done .......................................................... 7-7

Video .........................................................7-7

TV Timer ...................................................7-8

Rating Help ...............................................7-8

Max Spending............................................ 7-9

Channel Lists .................................................7-9

Done ........................................................ 7-10

Video .......................................................7-10

AutoSet ....................................................7-10

Rename....................................................7-10

Clear........................................................7-10

Set............................................................7-10

Tag Boxes................................................7-11

MyLogos™..................................................7-11

Done ........................................................ 7-11

Page viii

Table of Contents

Installation....................................................7-11

VCR Setup....................................................7-12

Brand .......................................................7-12

Code.........................................................7-12

Test (Record/Stop) ...................................7-12

Scheduler......................................................7-12

Done ........................................................7-12

Video........................................................7-12

Event Scheduling Options........................7-13

Editing an Event ......................................7-13

Check Mail ...................................................7-14

Message ...................................................7-14

Page.........................................................7-14

Erase........................................................7-14

Purchases......................................................7-14

Done ........................................................7-15

Video........................................................7-15

History .....................................................7-15

Upcoming Purchases...............................7-15

Buy...........................................................7-15

Buy Options .............................................7-15

Cancel Purchase......................................7-16

Purchase History .....................................7-16

Caller ID.......................................................7-16

Call History and Callback .......................7-16

Done ........................................................7-16

Video........................................................7-17

Disable .................................................... 7-17

Call History............................................. 7-17

Callback .................................................. 7-17

Help......................................................... 7-17

Lock/Unlock ................................................ 7-17

Locking Procedure.................................. 7-18

Unlocking Procedure..............................7-18

Temporarily Overriding the Lock........... 7-19

The Remote Control ......................................... 8-1

Remote Control Buttons................................ 8-2

Programming the Remote Control................. 8-3

Programming Mode.................................. 8-3

Code Scan ................................................. 8-3

Code Entry ................................................ 8-4

Using the Remote Control............................. 8-8

Switching the Remote Control

to Operate Additional DST-3000

Receivers .............................................. 8-8

Identifying Codes That Have Been

Stored ................................................... 8-8

Controlling Other Components Using

the AUX Button .................................... 8-9

Questions and Answers ................................... A-1

Specifications................................................ A-3

Limited Warranty ......................................... A-4

Page ix

A First Look at the HD System

Congratulations! You’ve selected one of the most advanced digital video and audio components available today. You now have the capacity to receive hundreds of channels of video programming and digital-quality audio.

What You Should Do First

Your HD system is both a sophisticated technical product and an easy-to-operate source of entertainment. You should complete the following steps to achieve the greatest performance from your system:

● Confirm the following items are included with your DST-3000 receiver

● Access card (located behind the door on your DST-3000 receiver)

● IR (infrared) remote control with 2 AA batteries

● Owner’s Manual

● 6-foot coaxial RF cable

● 6-foot VCR control cable

● 25-foot Telephone cable

● 8-foot 5-conductor component audio/video cable.

● Read this manual to familiarize yourself with the system.

● Install the DST-3000 receiver.

● Connect the terrestrial antenna or cable for local analog and digital channels.

● Install the DIRECTV PLUS™ antenna and cables. Professional installation is strongly

recommended.

● Align the satellite dish antenna.

● Arrange for programming from DIRECTV.

Page 1-1

Toshiba DST-3000 High Definition Digital Receiver

How Does All This Work?

First, here is some information about your HD receiver. Your HD receiver can receive three types of television signals:

● Analog signals in

NTSC (National Television Systems Committee—traditional TV signals) format—from terrestrial, or broadcasting towers built on earth, and cable sources.

● Digital signals in

AT SC (Advanced Television Systems Committee—digital TV signals) format—from terrestrial sources.

The Broadcasting and Receiving network

● Digital Satellite signals—from DIRECTV satellites in space. These signals can be either

Standard Definition (SD) signals or High Definition (HD) signals.

Second, here is some information about the broadcasting and receiving network shown.

Television stations, film studios, and other broadcasters send signals to earthbound terrestrial broadcasting towers and satellites. The tower shown on the right is sending Digital ATSC format signals and the more traditional Analog NTSC format signals. Both ATSC and NTSC signals can be received by the same VHF/UHF antenna normally mounted on a roof or in an attic. The satellites shown are sending DIRECTV programming signals which are received by a DIRECTV PLUS™ Satellite Dish Antenna usually mounted on a roof or on the ground. These satellites are located in geostationary orbit. Cable television signals are received through cables installed by cable television providers. The terrestrial broadcast (from a tower), satellite, and cable signals then go into your DST-3000 receiver where they are processed and sent to your television set.

Page 1-2

A First Look at the HD System

HD System Components

There are three main components of the HD system. They are the DIRECTV PLUS™ satellite dish antenna (not included), the DST-3000 receiver, and the remote control.

The DIRECTV PLUS™ Satellite Dish Antenna

The satellite dish antenna, such as the Toshiba HSD-3, is the component that receives the digital signals. It must be mounted to a solid outdoor surface that allows a clear view of the southern sky.

The large dish-shaped part is known as the reflector. The oval-shaped DIRECTV PLUS™ satellite dish antenna enables reception of DIRECTV High Definition programming throughout the United States and local stations in specific cities. The dimensions of the oval dish reflector are approximately 18 inches high by 24 inches wide.

LNBs

LNB support arm

Reflector

Mast

Toshiba HSD-3

A Low Noise Block (LNB) Downconverter assembly is attached to

Base plate

the satellite dish antenna at the end of a tubular arm. Your assembly provides for receiving signals from multiple satellite orbit locations and distributing the signal

The satellite dish antenna parts. While your dish may vary

in appearance, the components are referred to using the

same names.

to the HD receiver and up to 3 more DIRECTV digital satellite receivers through the use of a multiswitch (not shown).

The mounting bracket and base plate make adjustments easy during installation. Once the satellite dish antenna has been properly positioned to point toward the satellites, you should never need to adjust it again.

Professional installation of the satellite dish antenna is strongly recommended. This is recommended to help ensure your personal safety, compliance with electrical codes, and compliance with all specifications. The proper installation and aiming of the dish antenna is critical for proper operation. To arrange professional installation, please contact your dealer. Refer to the instructions included with the satellite dish for more details.

Page 1-3

Toshiba DST-3000 High Definition Digital Receiver

▲

The DST-3000 Receiver with DIRECTV PLUS™ Receiver Built-in

The DST-3000 receiver is one of the most compact available today. The basic features for setup, installation, and viewing programming can be accessed from the front panel keys.

The front of the DST-3000 receiver

Your access card is located behind the door on the right side of the DST-3000 receiver. This special card contains information about your services. This card should not be removed except to protect the DST-3000 receiver from unauthorized use or to replace the card when DIRECTV supplies a new one.

The power key ( ) is used to turn the DST-3000 receiver on and off. The power light will

POWER

illuminate when the unit is on.

The information key ( ) is used to display descriptions of programs and channels on your

INFO

TV screen.

Pressing the ( ) key will display the on-screen guide, where you can see a listing of all available programs. If the ( ) key is pressed while the program guide is already displayed,

GUIDE

the Guide Pop-Up menu will be displayed. The Guide Pop-Up menu provides access to the Main Menu or to the different program guide sorting options.

The four directional keys, up ( ), down ( ), left ( ), and right ( ), are used to move the highlight

▲

around the program guide and menus. Up and down keys also provide access to the BannerGuide™ when menus aren’t displayed.

The select key ( ) is used to access a highlighted guide or menu item.

SELECT

Page 1-4

A First Look at the HD System

The rear of the DST-3000 receiver (power cord not shown)

The rear of the DST-3000 receiver has numerous jacks for connection to your audio/video entertainment system. You will also find the power cord permanently connected to the back.

The SATELLITE-IN F-type jack is for connecting the cable from your satellite dish antenna to the DST-3000 receiver. Be sure that you use RG-6 cable only. The SATELLITE-IN F-type jack can also accept a terrestrial analog or digital input when combined with the satellite signal using a diplexer.

Note: Refer to “HD Receiver and Satellite Dish Antenna with Terrestrial Antenna or Cable Service” in Chapter 2 for more information on using a diplexer. This is an advanced installation technique and professional installation is recommended.

The IN FROM ANT jack is for connecting a terrestrial analog or digital input to your DST-3000 receiver.

The OUT TO TV F-type jack is an RF output that you may connect to your standard definition (SD) TV or videocassette recorder (VCR) (depending on your entertainment system). Note that the CH3/CH4 switch enables you to select the channel on which DST-3000 receiver signals will appear. Set your TV or VCR to match this.

Three component video output jacks Y (Luminance), P from Luminance), and P

(the amount of color Blue is different from Luminance) are connected

(the amount of color Red is different

to a High Definition (HD) monitor set to achieve highest quality video images. The output format is always 1080i.

The phono-type AUDIO output jacks, labeled and color-coded (L is white, and R is red) to indicate Left and Right, can be used for connection to your SDTV, VCR, or audio system. The phono-type composite VIDEO output jack is color-coded yellow. You may use this jack for connection to your SDTV or VCR. The multiple-pin S-VIDEO jack is for high-quality video output. Use this jack to achieve the clearest picture for your TV or VCR. The output format is 480i.

The VCR CONTROL mini-jack is for connecting the VCR control cable that is included with the system. With this cable, the DST-3000 receiver can interface with most popular brands of VCRs to record selected programs automatically.

There is one DIGITAL AUDIO OUT connector which is OPTICAL. It provides signals for

connection to a Dolby

Digital decoder.

The RF REMOTE jack is provided for future accessory use.

The standard RJ-11 modular PHONE JACK is for connecting the DST-3000 receiver to your telephone line. This telephone connection is necessary to access certain program offerings such as Pay Per View. Telephone calls generated by the DST-3000 receiver are toll-free. The telephone line connection will not normally interfere with your telephone operation.

Page 1-5

Toshiba DST-3000 High Definition Digital Receiver

POWER

▲

The Remote Control

The remote control uses an invisible infrared (IR) light to send signals to your components when you press the keys. You must aim the remote control toward the component for it to receive the command.

The remote control can control your DST-3000 receiver and most TV brands, as well as VCRs and many other auxiliary devices such as cable boxes, amplifiers, and DVD players.

The mode keys across the top of the remote control enable you to specify the device you intend to control. This is important since many devices share the same keys, such as the key and the numeric keys. You must press the appropriate device key before

pressing a command key to make sure the remote control sends the right signal to the right device. The only keys that deviate

from this rule are the 9 keys in the center section of the remote plus

EXIT

the ( ) key, as they are always associated with the DST-3000 receiver.

For the DST-3000 receiver only, the four directional keys will cause the on-screen highlight to move in the direction you want. The keys will be referred to as , , , and .

The select key ( ) is one of the most important keys. Pressing

SELECT

the key will tell the DST-3000 receiver that you wish to

SELECT

choose the highlighted item.

▲

LIGHT

DVD

AUX

MOVIES

ABC

JKL

STU

EXIT

HD/SD

INPUT

STOP SOURCE

REC

CROP/LTRBX

VCR

NEWS

SPORTS

GHI

DEF

PQR

MNO

VWX

ALL

ALPHA

&!/



LIST

INFO

FAV

SELECT

BANNER

ACTION

MUTE

SERVICES

PLAY PIP

PAUSE REW FF

STILL LOCATE SWAP

POWER

SAT

VOL

GUIDE

P A G E

The arch of keys above the directional keys control frequently used functions. These include menu ( ), program information

INFO FAV GUIDE

( ), favorite lists ( ), and program guide ( ) keys.

Pressing the key displays the action icon in the upper left

ACTI ON

The remote control

CT-819

corner of your screen for a few seconds. During this time, you can press other keys to access special functions indicated in blue above the keys. Refer to the chart on the next page for a list of

ACTI ON

key functions.

Page 1-6

A First Look at the HD System

SAT

The following chart describes the key functions for easy reference:

ACTI ON

Keys Label Feature

ACTI ON

FAV

–

INPUT

LIST Displays the CHANNEL LISTS screen

SERVICES Displays the Alternate Services menu

MOVIES Filters the on-screen guide to movies only*

SPORTS Filters the on-screen guide to sports only*

NEWS Filters the on-screen guide to news only*

ALPHA Select channel by call sign

HD/SD Switches the output of the HD receiver

between HD and SD**

ACTI ON

CROP/

Modifies video display viewing format

LTR BX

ACTI ON

ALL Removes all on-screen guide filters.

* Pressing this sequence a second time will undo the respective filter. ** HD formatted video output (1080i) uses the Y, P

, and Pb jacks. SD formatted

video output (480i) uses the Audio/Video (A/V) and Out to TV jack. Note: The first time you turn your system on, the HD formatted video output is active. You may have to press the key followed by the key sequence

ACTI ON

INPUT

twice to get any picture. A complete explanation of switching from HD to SD can be found in the section “Now You Can Turn It On” on page 2–14.

The remaining keys are DST-3000 receiver-specific keys and common device keys, including numbers, channel up and down, etc. The functions of these keys change depending on the device currently selected.

Please refer to “Controlling the DST-3000 Receiver” in Chapter 3 for more remote control capabilities and “Programming Your Remote Control” in Chapter 8 for setting your remote control to handle other audio/video components.

Descriptions and details of each individual key will be given in the appropriate subsections throughout this manual.

Page 1-7

Toshiba DST-3000 High Definition Digital Receiver

Installing the Remote Control Batteries

Before the remote control can be used, the two supplied AA batteries need to be installed. First, unsnap the battery cover from the back of the remote control. Install each fresh battery as shown, making sure that the + and – on each battery line up with the marks in the battery compartment. Next, snap the cover back onto the remote control.

Refer to “Programming Your Remote Control” in Chapter 8 for setting the codes to control the devices in your entertainment system.

Battery installation

Page 1-8

Setting Up Your Satellite Receiver

DANGER

To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.

This chapter provides step-by-step instructions for setting up your HD system and connecting it to your television or entertainment system.

The carton includes the DST-3000 receiver with DIRECTV PLUS™ receiver built-in, an access card (already installed in the DST-3000 receiver behind the door), an IR remote control (batteries included), cables, and this Owner’s Manual.

You now need to decide where you want to place the DST-3000 receiver. Choose a location near your TV where the power cord or cables will not be inadvertently disconnected.

CAUTION

Do not stack electronic components or other objects on top of the HD receiver. The slots on top of the receiver

must be left uncovered to allow proper airflow to the unit. Blocking the airflow to the unit could impair performance or damage your receiver. Also do not stack

the HD receiver on top of a “hot” component such as an audio power amplifier.

Page 2-1

Toshiba DST-3000 High Definition Digital Receiver

Choosing the Best Connection for Your Entertainment System

There are a number of ways to connect the DST-3000 receiver, depending on the other audio/ video equipment you wish to use. The simplest hookups are described in the following subsections.

The rear of the DTS-3000 receiver (power cord not shown)

Before connecting the DST-3000 receiver to your entertainment system, you should connect the phone line. This can be done by plugging one end of the provided telephone cable into the PHONE JACK on the back of the DST- 3000 receiver and the other end into a telephone wall jack. If you do not have a telephone jack within reach, you should move the DST-3000 receiver

The phone line

and jack

to be within reach of a telephone wall jack, buy a longer telephone cable, or have a new phone jack installed.

To suit your specific needs, you may need to purchase additional connectors and/or cables from your dealer or electronic hardware store. Choose which hookup method to use based on:

● The capabilities of your TV and VCR.

● Your desire to receive local terrestrial analog and/or digital programming through the

DST-3000 receiver.

● Any other devices you want to include in the system (stereo, second VCR, etc.).

Before attempting to connect anything, position yourself so you are looking at the back of your components. Note the various input and output receptacles, their shapes, and how they are labeled. Then read through the rest of this connection subsection before choosing a hookup method and proceeding with the actual installation.

Note: Make sure the DST-3000 receiver, TV, VCR, and any other devices to be connected are unplugged from the power outlet while hooking them up.

Some of the connection methods described in this chapter may require optional cables or accessories that are not included with your DST-3000 receiver.

Page 2-2

Setting Up Your Satellite Receiver

HD Receiver and Satellite Dish Antenna with Terrestrial Antenna or Cable Service

Follow these steps indicated by the diagram below:

1) Connect the RG-6 Coaxial Cable from the satellite dish antenna to the back of the HD receiver using the connector marked SATELLITE IN.

Optional Hookup: If you plan to combine an outside terrestrial antenna with the signal from the satellite dish antenna, obtain a signal Diplexer* from your local retailer of satellite accessories. Connect the RG-6 Coaxial Cable from the satellite dish antenna to the “power pass” input of the Diplexer, and connect the coaxial cable from the terrestrial antenna to the other input. Connect the output of the Diplexer to the back of the HD receiver at the connector marked SATELLITE IN.

* Note: It is very important that you use a Diplexer that is designed to combine

satellite signals and terrestrial signals. Standard signal combiners are not compatible.

2) Connect the cable from your terrestrial antenna or cable TV service to the HD receiver at the connection marked IN FROM ANT.

Optional Hookup: If you plan to record a terrestrial signal while watching satellite programming, or vice versa, connect the cable from your terrestrial antenna or cable TV service to the input of a standard two-way splitter as shown in the hookup diagram.

Page 2-3

Toshiba DST-3000 High Definition Digital Receiver

Note: Signals from a terrestrial antenna and cable TV can be connected to the IN FROM ANT connector and diplexed into the SATELLITE IN connection simultaneously. However, the receiver does not support the simultaneous connection of two terrestrial antenna signals or two cable signals.

Note: In order for the Advanced Program Guide™ to receive the correct listing of local channels and local program information from DIRECTV, make sure you select the correct zip code or cable provider on the LOCAL PROVIDERS screen. Refer to Chapter 4, “Setting Up the Satellite Dish Antenna and Terrestrial Inputs.”

HD Receiver and HDTV Monitor

Follow these steps indicated by the diagram on the next page:

1) Connect the satellite dish antenna and terrestrial antenna or cable service to the HD receiver following instructions in “HD receiver and Satellite Dish Antenna with Terrestrial Antenna or Cable Service” on page 2–3.

2) Connect one set of Component Video Cables (one green Y connector, one red P tor, and one blue P marked Y, P

monitor using the HDTV input connections marked Y, P

Note: Connect the Y, P

, and Pb connectors on your TV that are compatible with HD signals in the

1080i scanning rate and that comply with the EIA 770.3 signal standards. Refer to your television owner’s guide for verification.

connector) to the back of the HD receiver using the connections

, and Pb. Connect the other ends of this cable to the back of the HDTV

, and Pb.

, and Pb connectors of the HD receiver only to the Y,

connec-

3) Connect one set of audio cables (one white left audio connector and one red right audio connector) to the back of the HD receiver using the connectors marked AUDIO L, R. Connect the other end of the audio cables to the back of the HDTV monitor using the audio inputs.

Note: This connection allows the use of the speakers in the TV to hear the sound.

4) Optional: Connect one set of audio cables and a video or S-video cable to the back of the HD receiver using the connectors marked AUDIO L, R and VIDEO or S-VIDEO.

Connect the other end of audio and video cables to the back of the HD monitor using the AUDIO and VIDEO or S-VIDEO inputs.

Note: This connection allows you to send standard 480i signals to your TV.

For better standard definition performance, if your TV has an S-VIDEO connector, then use an S-video cable instead of the yellow video cable.

Note: When the HD receiver is converting all signals to standard 480i signals that can be viewed on standard video inputs of TVs, there will be no signals on the Y, P

, and Pb connectors. When the HD receiver is converting all signals to

1080i format that can be sent to the HDTV input of HD monitors, there will be no standard 480i signals to standard video inputs of TVs.

Page 2-4

Setting Up Your Satellite Receiver

If you have connected a VCR into your entertainment system in a way that routes the cables from the DST-3000 receiver to your VCR before the signal reaches the TV, you may experience a distorted picture if you attempt to record a copy-protected program. These programs are identified by a “Can’t Tape” symbol in the banner area of the screen. If this occurs, simply stop the recording process and your picture will automatically correct itself.

Page 2-5

Toshiba DST-3000 High Definition Digital Receiver

HD Receiver with HDTV Monitor and VCR

Follow these steps indicated by the diagram on the next page:

1) Connect the satellite dish antenna and terrestrial antenna or cable service to the HD receiver following the instructions in “HD Receiver and Satellite Dish Antenna with Terrestrial Antenna or Cable Service” on page 2-3.

2) Connect one set of Component Video Cables (one green Y connector, one red P tor, and one blue P marked Y, P

monitor using the HDTV input connections marked Y, P

Note: Connect the Y, P

, and Pb connectors on your TV that are compatible with HD signals in the

1080i scanning rate and that comply with the EIA 770.3 signal standards. Refer to your television owner’s guide for verification.

Note: This connection allows the use of the speakers in the TV to hear the sound.

connector) to the back of the HD receiver using the connections

, and Pb. Connect the other ends of this cable to the back of the HDTV

, and Pb.

, and Pb connectors of the HD receiver only to the Y,

connec-

4) Connect a set of audio/video or S-video cables to the second set of AUDIO L, R, and VIDEO or S-VIDEO connectors on the back of the HD receiver. Connect the other end to the AUDIO, VIDEO, or S-VIDEO input connections on the back of the VCR.

5) Connect another set of audio/video or S-video cables to the back of the VCR using the AUDIO and VIDEO output connection. Connect the other end of this cable to a group of standard AUDIO, VIDEO, or S-VIDEO input connections on the back of your TV.

Note: This connection allows you to send HD receiver signals, converted to standard 480i signals, to your VCR so they can be recorded.

You can see the playback of a video tape by selecting this input on your TV. You can also pass HD receiver signals, converted to standard 480i format, through your VCR to your TV; however, you may need to turn on your VCR to pass these signals.

When the HD receiver is converting all signals to standard 480i signals that can be recorded by standard VCRs, there will be no signals on the Y, P

connectors.

, and

When the HD receiver is converting all signals to 1080i format that can be sent to the HDTV input of the HD monitors, there will be no standard 480i signals to send to VCRs or standard video inputs of TVs.

For better performance, if both the TV and the VCR have S-video connectors, use S-video cables instead of standard yellow video cables.

Page 2-6

Note: If you have connected a VCR into your entertainment system in a way that routes the cables from the DST-3000 receiver to your VCR before the signal reaches the TV, you may experience a distorted picture if you attempt to record a copy-protected program. These programs are identified by a “Can’t Tape” symbol in the banner area of the screen. If this occurs, simply stop the recording process and your picture will automatically correct itself.

Setting Up Your Satellite Receiver

Page 2-7

Toshiba DST-3000 High Definition Digital Receiver

HD Receiver and Standard Definition TV Monitor

Follow these steps indicated by the diagram on the next page:

2) Connect one set of standard audio/video cables (one yellow video connector, one white left audio connector, and one red right audio connector) to the back of the HD receiver using the connectors marked AUDIO L, R and VIDEO. Connect the other end of the audio/video cable to the back of the TV monitor using the AUDIO and VIDEO inputs.

Optional: If your TV has an S-VIDEO input, then connect one end of an S-video cable to the back of the HD receiver using the output marked S-VIDEO. Connect the other end of the S-video cable to the back of the TV using the S-VIDEO input that matches the previously used audio inputs. If you use an S-video cable, you will not need to use the yellow video cable.

3) Optional: If the TV does not have AUDIO/VIDEO input connectors, then connect one end of a coaxial RF cable to the OUT TO TV connector on the back of the HD receiver. Connect the other end of the coaxial RF cable to the antenna input connector on the back of the TV. Set the CH3/CH4 switch on the HD receiver to the channel not used in your area. It is this channel you will select on your TV to view the HD receiver.

Note: When the HD receiver is in HD output mode or in standby (power LED off), the RF signal received on the IN FROM ANT connector will pass through to the OUT TO TV connector.

Page 2-8

Setting Up Your Satellite Receiver

HD Receiver with Standard Definition TV Monitor and VCR

Follow these steps indicated by the diagram on the next page.

2) Connect one set of standard Audio/Video cables (one yellow video connector, one white left audio connector, and one red right audio connector) to the back of the HD receiver using the connectors marked AUDIO L, R and VIDEO. Connect the other end of the Audio and Video cables to the back of the TV monitor using the Audio/Video input connectors.

Optional: For better performance, if your TV has an S-VIDEO input, then use an SVideo cable instead of a standard yellow Video cable.

3) Connect another set of standard Audio/Video cables to the back of the HD receiver using the connectors marked AUDIO L, R and VIDEO. Connect the other end of the audio and video cables to the back of the VCR using the AUDIO/VIDEO input connectors.

Page 2-9

Toshiba DST-3000 High Definition Digital Receiver

4) Connect another set of standard audio/video cables to the back of the VCR using the AUDIO and VIDEO output connectors. Connect the other end of this cable to another group of unused input connectors on the back of the TV.

Note: There are possible variations to steps 3, and 4 above. For example, if your TV or monitor has only one set of AUDIO/VIDEO input connectors, or if you have an S-VHS VCR, you may choose the following connection variation: Connect the AUDIO and VIDEO or S-VIDEO connectors of the HD receiver only to the VCR. Then connect the VCR output connectors to the TV. In this situation, you may need to turn on your VCR to pass HD receiver signals to your TV.

5) Optional: If the TV does not have AUDIO/VIDEO input connectors, then connect one end of a coaxial RF cable to the OUT TO TV connector on the back of the HD receiver. Connect the other end of the coaxial RF cable to the antenna input connector on the back of the VCR. Connect another coaxial RF cable to the antenna output connector on the back of the VCR and connect the other end of this cable to the ANTENNA or VHF input connector on the back of the TV. Set the CH3/CH4 switch on the HD receiver to the channel not used in your area. It is this channel you will select on your TV to view the HD receiver.

Note: When the HD receiver is in HD output mode or in standby (power LED off), the RF signal received on the IN FROM ANT connector will pass through to the OUT TO TV connector.

Page 2-10

Setting Up Your Satellite Receiver

Page 2-11

Toshiba DST-3000 High Definition Digital Receiver

HD Receiver and Dolby® Digital Receiver or Decoder

Follow these steps indicated by the diagram below:

1) Connect an optical digital cable (not included) to the back of the HD receiver using the connector marked DIGITAL AUDIO OUT. Connect the other end of this cable to the optical input on the back of your Dolby Digital receiver or decoder.

2) Check the Owner’s Guide for the Dolby Digital receiver or decoder for proper set-up and operation.

AUDIO

LYL

VCR

PHONE JACK SATELLITE IN

REMOTE

VIDEO VIDEO

CONTROL

S-VIDEO

DIGITAL

AUDIO OUT

OUT TOTV

CH 3 CH 4

IN FROMANT

HD receiver

Optical digital cable

Amplifier with Dobly Digital (AC-3) processing

Home theate

Page 2-12

+ 68 hidden pages

Toshiba DST-3000 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual