TEC Drawer Unit
Table of Contents
DRWST-53 SERIES
T&C
TEC CORPORATION
l
Request Regarding Maintenance
0 Cleaning
n
Utilize our maintenance services.
After purchasing the machines, contact your sales agent
once per year or so to have the inside of the machines
cleaned. Otherwise, dust will build up inside the machines
and may cause fire or malfunction. Cleaning is particularly
effective before humid rainy seasons.
H Our maintenance service performs the periodical checks
and other work required to maintain the quality and performance of the machines, preventing accidents beforehand.
For details, please consult your sales agent or maintenance
and service agent.
n
Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile
solvents, as this will deteriorate the cabinet or other parts or
cause the paint to peel.
* When cleaning the machines, be sure to first
unplug the power cord from the outlet for safety
reasons.
n
Do not use benzine or alcohol, etc., as these
solvents will deteriorate the cover or cause the
paint to peel.
Leaving rubber orvinyl products in contact with the
machines for long periods may leave stains on the
machine surfaces.
n
Cleaning the covers and keyboards:
Wipe the covers and keyboards with a soft cloth.
When using a chemically treated cloth, be sure to
follow the precautions specified for it.
1 Cleaning the display units:
Turn off the power and then wipe the display units
with a dry cloth.
*Do not rub or knock the display units with a hard
object as they are easily damaged. Do not use
thinner or other solvents.
n
Use a neutral detergent diluted with water when
the machines are particularly dirty.
1) Soak a cloth in the detergent fluid and wring it
out tightly. Then wipe off the dirt with the cloth.
2) Finish by wiping the machines off with a dry
cloth.
- VIII -
DRWST-53 SERIES
TABLE OF CONTENTS
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............
EOI -19022
Page
1
1 .l Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..........
2. APPEARANCE AND NOMENCLATURE ...............................................................................................
3. INSTALLING THE DRAWER .................................................................................................................
1
1
2
4. HANDLING OF THE DRAWER .............................................................................................................. 3
5. HOW TO FIX DRAWER IN PLACE ON
THE TERMINAL ..................................................................... .4
6. SPECIFICATIONS ................................................................................................................................. 6
Copyright 0 1995
by TEC CORPORATION
All Rights Reserved
2613 Nakameouro. Menurn-ku. Tokvo. JAPAN
DRWST-53 SERIES
EOl-19022
1. INTRODUCTION
Thank you for purchasing the TEC DRWST-53 Series Remote Drawer. This drawer can be connected to
various terminals including the ST-4500 Series, which has been developed as a high-grade POS terminal.
This drawer can be used as either first drawer or secondary drawer (the second drawer required).
1 .I Precautions
Do not subject the equipment to sudden shocks.
1)
The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent
4
solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.
DO NOT POUR WATER directly onto the drawer and NEVER IMMERSE THE DRAWER IN WATER.
3)
Avoid using in locations subject to vibration and direct sunlight.
4)
Be sure to install the equipment on a flat surface.
5)
Be sure to use the equipment within the proper ranges of power, current consumption, temperature and
6)
relative humidity.
Do not roughly open or close the drawer.
7)
Never attempt to modify the TEC equipment by yourself.
8)
2. APPEARANCE AND NOMENCLATURE
Cash
\ Drawer Release Lodt
Drawer Cable
-l-
Accessory Parts
0
‘ITEC
DRWST-53 SERIES
EOl-19022
sE”c
9
Drawer Release Key
(1 pc; 2 keys)
Nylon Clamp
(1 PC)
Cash Drawer Cover Key
Flanged Screw (M3X8)
P
(1 pc; 2 keys)
(1 PC)
3. INSTALLING THE DRAWER
Turn the POWER SWITCH to OFF of the ST-4500 terminal before connecting the cables.
Connect the connector of the Drawer Cable to DRWlT of the Control Unit.
Flanged Screw (M4x8)
(1 PC)
-2-
4. HANDLING OF THE DRAWER
n
Manual cash drawer releasing
l
Opening the Drawer
Usually, the drawer is released automatically on finalizing each transaction. In the event of a power failure or
othertroubles, the drawer can be opened in the following
manner.
1) Insert the Drawer Release Key into the Drawer Release Lock and turn the key clockwise. The drawer
will now open (Fig. 1).
2) The Drawer Release Key can be taken out by returning it to the original position.
DRWST-53 SERIES
EOl-19022
Fig. 1
l
Removing the Drawer
1) Pull the drawer out, and when it stops at the stopper,
lift the drawer up and pull it further out (Fig. 2). When
it stopsagain at the roller fixed in the drawer housing,
lift it and pull it out (Fig. 3).
2) When installing the drawer, the rollers on the drawer
should be placed on the rails of the drawer cabinet.
Then, push it all the way in.
n
Locking the cash drawer cover (CDC)
l
Locking (Fig. 4)
Fig. 2
1) Pushthecashdrawercovertothe backofthedrawer.
2) Press the cover lightly, insert the key into the keyhole
on the cover, and turn it to lock.
l
Unlocking
Unlock the cover using the key, and lift the front end.
NOTE
Money case slot is flexible. Figures of money case are MC-8.
Fig. 4
-3-
DRWST-53 SERIES
EOl-19002
5. HOW TO FIX DRAWER IN PLACE ON THE TERMINAL
To attach the drawer (DRWST-53) to the ST-4500 terminal and use this terminal as an integrated terminal,
follow the procedure below.
1) Remove the top cover and the control unit from the ST-4500 terminal.
Double Sems Screw (M3x8)
Double Sems
2) Remove the cable holder that is attached to the rear of the bottom of the drawer. Place the excessive cable
in
the area where the cable holder has been detached, excluding 25cm from the top of the drawer cable.
Then, reattach the cable holder.
P \
, Cable Holder
Drawer
Cable
-4-
DRWST-53 SERIES
Cut the grommet in the upper part of the drawer using a cutter. Take out the drawer cable from the upper
3)
part of the drawer and fix in place onto the drawer, using the nylon clamp and screw that are attached to the
DRWST-53.
Cable
EOl-19022
Attach the drawer to the ST-4500 terminal and fix it in place with the screw attached to the DRWST-53.
4)
Flanged Screw (M4x8)
fr
DRWST-53
-5-
6. SPECIFICATIONS
DRWST-53 SERIES
EOl -19022
Size
Weight
Power Consumed
Interface with the Control Unit
Ambient Temperature
Relative Humidity
Cable Length 1.5 m
460 mm (W) x 430 mm (D) x 120 mm (H)
(including the rubber feet)
8.5 Kg
0.2 A Max.
Drawer release signal and release sense signal
(Power is supplied by the Control Unit : DC + 24 V)
0°C to 40°C
10% to 90% RH (with non condensation allowed)
-6-
T&C
TEC CORPORATION
PRINTED IN JAPAN
EOI -19022
El
Loading...