Toshiba DF03A - IK CCTV Camera, DP30A - Day/Night PTZ Dome Camera CCTV Instruction Manual

INSTRUCTION MANUAL

DOME CAMERA

IK-DP30A

TABLE OF CONTENTS

IMPORTANT SAFEGUARDS ................................................ 2

1. Features and description .............................................. 4

2. Cautions ........................................................................ 4

3. Components ................................................................. 4

4. Part names and Locations ............................................ 5

5. Connections .................................................................. 6

6. Operation ...................................................................... 7

7. Menu Directory ............................................................. 29

8. Switch Setting ............................................................... 31

9. Installation..................................................................... 34

10. Specifications................................................................ 37

Please read this manual thoroughly before use, and keep it handy
for future reference.

Record in space provided below the Model No. and
the Serial Number as found on the label on the
bottom of the camera.
Model. No. IK-DP30A Serial No.
Retain this information for future reference.

ZEIM-4000008G A.1

- 2 -

1. Read Instructions

All the safety and operating instructions should be
read before the product is operated.

2. Retain Instructions

The safety instructions and instruction manual
should be retained for future reference.

3. Heed Warnings

Comply with all warnings on the product and in
the instruction manual.

4. Follow Instructions

Follow all operating and use instructions.

5. Cleaning

Disconnect this video product from the power
supply before cleaning.

6. Attachments

Do not use attachments not recommended by the
video product manufacturer as they may cause
hazards.

7. Water and Moisture

Do not use this video product near water. Some
examples are: near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool.

8. Accessories

Do not place this video product on an unstable cart,
stand, tripod, bracket or table. The video product
may fall, causing serious injury to a person, or
serious damage to the product. Use only with
stand, tripod, bracket, or table recommended by
the manufacturer, or sold with the video product.
Any mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.

9. Ventilation

This video product should never be placed near or
over a radiator or heat register. If this product is
placed in a built in installation verify that there is
proper ventilation so that the camera temperature
operates within the recommended temperature
range.

10.Power Sources

This video product should be operated only from
the type of power source indicated on the marking
label. If you are not sure of the type of power supply
to your location, consult your product dealer.

11. Power-Cord Protection

Power cords should be routed so that they are not
likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to
cords at plugs, screws and the point where they
exit the product.

12.Installation

Install this video product on a firm and solid part of
the ceiling or wall. If installed on a weak place the
camera could fall causing injury and damage.

13.Lightning

For additional protection on this video product
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
power supply and cable system. This will prevent
damage to the video product due to lightning and
power-line surges. If lightning occurs, do not touch
the unit or any connected cables in order to avoid
electric shock.

14.Overloading

Do not overload the power supply or extension
cords as this can result in a risk of fire or electric
shock.

15.Object and Liquid Entry

Never push objects of any kind into this video
product through openings as they may touch
dangerous electrical points or short-out parts that
could result in a fire or electrical shock. Never spill
liquid of kind on the video product.

16.Servicing

Do not attempt to service this video product
yourself as opening or removing covers may
expose you to dangerous electricity or other
hazards. Refer all servicing to qualified service
personnel.

17.Damage Requiring service

Disconnect this video product from the power
supply and refer servicing to qualified service
personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the video product.
c. If the video product has been exposed to rain or
water.
d. If the video product does not operate normally
by following the operating instructions in the
instruction manual. Adjust only those controls that
are covered by the instruction manual as an
improper adjustment of other controls may result
in damage and will often require extensive work
by a qualified technician to restore the video
product to its normal operation.
e. If the video product has been dropped or the
cabinet has been damaged.
f. When the video product exhibits a distinct change
in performance-this indicates a need for service.

18.Replacement Parts

When replacement parts be sure the service
technician uses replacement parts specified by the
manufacturer or have the same characteristics as
the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.

19.Safety Check

Upon completion of any service or repairs to this
video product, ask the service technician to perform
safety checks to determine that the video product
is in proper operating condition.

IMPORTANT SAFEGUARDS

- 3 -

• The CAUTION label, shown on the left,
is attached on the camera.

CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightening flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.

The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.

WARNING :

TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.

CAUTION :

CONNECT 24V AC UL LISTED CLASS
2 POWER SUPPLY.

FIELD INSTALLATION MARKING :

THIS INSTALLATION SHOULD BE
MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO
ALL LOCAL CODES.

FCC (USA)-INFORMATION
NOTE : This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

USER-INSTALLER CAUTION : Your authority to operate this FCC verified equipment could
be voided if you make changes or modifications not expressly approved by the party.

- 4 -

1. Features and description

Quick Install Design - Cuts Installation Time in Half
480 Lines Horizontal Resolution
400 Degree/Second Pan
18X Optical/12X Digital Zoom
Privacy Zone Masking

0.01 Lux Minimum Illumination (1/4, IR Cut filter Off)
50dB Signal-To-Noise Ratio
64 Position Preset
Auto-Flip
Proportional Zoom

2. Cautions

(1) In order to protect the camera, avoid placing or using it under direct sunlight, rain or

dust.

(2) Avoid touching the zoom lens with your fingers. If necessary, use a soft cloth moistened

with alcohol to wipe off any dust.
(3) When the camera is not in use, keep the lens cap attached to protect the zoom lens.
(4) Avoid aiming the camera at the sun.
(5) Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may

appear on the screen. However, this is not a malfunction.
(6) Install the camera away from video noise. If cables are wired near electric lighting wires

or a TV set, noise may appear in images. In this event, relocate cables or reinstall

equipment.

3. Components

(1) Dome base ..................................... 1

(2) Dome drive ..................................... 1

(3) Accessories

Instruction manual .......................... 1

Install screw (3PCS) ....................... 1

- 5 -

4. Part names and Locations

120

120

°

°





120

120

°

°





35

35

°

°





φφ134

134

173.7

173.7

223.7

223.7

R19

R19

R1.9

Φ139.8

Control Terminal (RS-422)

Installation Notch

Installation Label

X18 Lens

Video out BNC connector

Installation Brackets (3 Iegs)

RS-422 termination switch

Dome Base

Dome Driv

e

Power Terminal
(24VAC only)

Screw for cover Iock
(Reserved)

- 6 -

5. Connections

Basic connection (Direct mode)

24V AC UL Iisted class 2 power supply

RS422
(twisted pair line)

Monitor

Keyboard

AC Adaptor

Make sure to connect to a power supply that allows for at least 35W consumption

RX - RX+

TX-

TX+

RX - RX-

TX - TX+

TX - TX-

RX+

RX-

RS422 Pin Out

2 wire
controller

2 nd
Dome Camera

In the direct mode the communication line from the keyboard (TX) where TX+ is connected to RX+
of the dome camera and TX- is connected to RX- of the dome camera. If connecting two or more
dome cameras, TX+ from the first camera is connected to RX+ of the second camera and TX- is
connected to the RX-.

- 7 -

6. Operation

(Power On display)

When the dome camera powers-up, the software version,
selected protocol, and other information are displayed on the
monitor.

6.1 ACCESSING THE MENU

Accessing the menu varies with the model controller being used. Several controllers are listed
below. Please refer to your model's instructions for information on inputting commands.

JK-UC1

Input 95 using the numeric keypad.
Press the PRESET button to display the MENU screen.

VLC485

Input 95# using the numeric keypad.
Press the PRESET button to display the MENU screen.

TOSHIBA IK-DP30A
VERSION***
PROTOCOL TOSHIBA-P
ADDRESS 1
COMM 4800/N/8/1

- 8 -

6.2 Preset Commands

The dome camera can set and perform various preset commands. The following table lists the
preset number and whether is can be set (SET) or performed (GO).
Presets 1-32 and 35-66 are user presets. Refer to your model's instructions for information on
inputting preset commands.

Preset Number Function

1-32 SET/GO Preset position 1-32

33 GO Flip

34 GO Home (return to 0 pan position)

35-66 SET/GO Preset position 35-66

70 GO Begin Auto patrol

71 GO Backlight compensation ON

72 GO Backlight compensation OFF

73 GO One push WB

74 GO One push trigger AF

75 GO Software version Display

76 GO P/T Initialize

83 SET Privacy Zone Setup menu mode

88 GO Color Mode IR Cut filter ON

89 GO Monochrome Mode IR Cut filter OFF

90 SET Set manual left limit stop

91 SET Set manual Right limit stop

92 SET Set Scan Left Limit Stop

93 SET Set Scan Right Limit Stop

95 SET Enter Menu Mode

96 GO Stop Scan

97 GO Begin Random Scan

98 GO Begin Frame Scan

99 GO Begin Auto Scan

6.3 PROGRAMMING PRESETS

Programming presets varies with the model controller being used. Several controllers are listed
below. Please refer to your model's instructions for information on inputting preset commands.

JK-UC1

Input the desired preset using the numeric keypad.
Press the SHIFT key.
The LED will light up.
Press the PRESET key.

VLC485

Input the desired preset using the numeric keypad.
Press the # key.
Press the PRESET key.

- 9 -

Pan Range 360 degrees continuous

Tilt Range 85 degrees (Indoor), 92 degrees (Outdoor)

Manual Pan Speeds 0.1° – 90°/s

Manual Pan Speeds (turbo) 150°/s

Manual Tilt Speeds 0.1° – 45°/s

Preset Speeds Pan: 400°/s max-set in menu

Tilt: 200°/s

6.6 SCAN FUNCTIONS

AUTO SCAN

The dome camera can perform an auto scan operation during power-up or by direct control from a
keyboard.

Scan limit stops ARE NOT set:

The dome camera will pan continuously until a manual pan, tilt, or zoom operation is performed
from the keyboard.

Scan limit stops ARE set:

The dome camera will pan continuously between scan limit stops until a manual pan, tilt, or zoom
operation is performed from the keyboard. To set scan limit stops refer to SCAN LIMIT STOPS
under PAN/TILT SETUP in the camera menu.

Zoom

At power-up, the zoom is fully zoomed out. When an auto scan is started directly from the keyboard,
the zoom will maintain the last magnification.

Tilt

At power-up, the tilt is set up by the menu. To set the tilt angle, refer to SCAN TILT ANGLE under
PAN/TILT SETUP. When an auto scan is started directly from the keyboard, the tilt will maintain the
last tilt angle.

6.4 PERFORMING PRESET OPERATIONS

JK-UC1/VLC485

Input the desired preset using the numeric keypad.
Press the PRESET button to perform the preset.

6.5 PAN/TILT FUNCTIONS

Manual PAN
Manual Pan is controlled from a keyboard and the speed ranges from 0.1 degrees/sec to 90
degrees/sec depending on the joystick position. In turbo mode the speed is 150 degree/sec. However,
this speed is limited when Proportional P/T is ON.

Manual TILT
Manual Tilt speed ranges from 0.1 degrees/sec to 45 degrees/sec. However, this speed changes
when Proportional P/T is ON.

- 10 -

FRAME SCAN

The dome camera can perform a frame scan operation during power-up and by direct control from
the keyboard.
Operation of zoom and tilt is the same as in Auto Scan.

Scan limit stops ARE NOT set:

The dome camera will move in 45-degree increments (called stops) horizontally until a manual
pan, tilt, or zoom operation is performed from the keyboard. See figure below.

stop

stop

stop

stop

stop

stop

stop(stop time)

scan speed

45

Scan limit stops ARE set:

The dome camera will move in 45-degree increments horizontally within the limit stops until a
manual pan, tilt, or zoom operation is performed from the keyboard. See figure below.

stop

stopstop

stop

stop

stop

B

stop

45

E

C

B

A

D

B

A A

Left Limit

Right Limit

scan speed

D

D

- 11 -

RANDOM SCAN

The dome camera can perform a random scan operation during power-up and by direct control
from the keyboard.
Operation of zoom and tilt is the same as in Auto Scan.

Scan limit stops ARE NOT set:

The dome camera will move between random stops and random tilt angles until a manual pan, tilt,
or zoom operation is performed from the keyboard. See figure below.

stop

stop

stop

stop

stop

stop

ex) A-C-H-E-G-B-D---

stop

stop

45

G

F

E

C

B

A

H

D

Scan limit stops ARE set:

The dome camera will move between random stops and random tilt angles within the limit stops
until a manual pan, tilt, or zoom operation is performed from the keyboard. See figure below.

stop

stopstop

stop

stop

stop

ex)A-D-B-D--

stop

stop

45

E

stop

Left Limit

C

B

A

D

Right Limit

- 12 -

6.7 CAMERA SETUP

6.7.1 FOCUS CONTROL

Direct

• The focus can be controlled directly using near or far focusing controls.

• The focus control has 4 varying speeds.

• One Push Trigger Auto Focus.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

CAMERA MENU

MODE AUTO
ACTIVE TIME 5S
INTERVAL TIME 5S
SENSITIVITY NORMAL

FOCUS MENU

• The Focus control has four options: Manual/Auto/Interval/Zoom Trigger

• In the manual mode the IK-DP30A focus is directly controlled with the near and far controls.

• When the camera is in Auto Mode, pressing the near and far controls will place the camera in
manual mode until there is a zoom or pan/tilt function.

• In Interval mode, the camera will switch between auto focus and manual focus according to the
Active Time and Interval Time respectively. Example: Active Time (auto) – Interval Time (manual)
– Active Time (auto) – Interval Time (manual)...

• The interval and active times can be set from 1 s to 255s.

• In Zoom Trigger mode, the camera remains in manual mode unless there is a zoom function.
After the zoom function is completed the camera returns to the manual mode.

• The sensitivity of the Auto Focus can be set to NORMAL or LOW.

To change the Focus options:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

Camera menu.

3. Position the cursor next to FOCUS and press the OPEN button to access the Focus menu.

4. Position the cursor next to the desired option and press the OPEN button to move the cursor to

the right.

5. Move the joystick up or down to select option setting.

6. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 13 -

6.7.2 WHITE BALANCE CONTROL

Direct

• The White Balance can be set by One Push Trigger operation.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

CAMERA MENU

The White Balance can be set to ATW (Auto Tracking White)/AUTO/ONE PUSHWB.

•ATW automatically adjusts the white balance for color temperatures from 2000K to 10000K.

•AUTO automatically adjusts the white balance for color temperatures from 3000K to 7500K.

• ONE PUSH WB can be set using 73 PRESET from a controller.

To change the White Balance:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

Camera menu.

3. Position the cursor next to WB and press the OPEN button to move the cursor to the right.

4. Move the joystick up or down to select ATW, AUTO, or ONE PUSH WB.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.7.3 AE CONTROL

Direct

• The Iris can be controlled directly using OPEN or CLOSE controls.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

CAMERA MENU

MODE FULL AUTO
AUTO SLOW SHUTTEROFF
SHUTTER SPEED 1/60
AE COMPENSATION 0
BACK LIGHT COMP OFF
DAY/NIGHT AUTO

AE

MENU

- 14 -

MODE

• AE mode can be set to FULL AUTO or SHUTTER PRIORITY.

• FULL AUTO mode:
The shutter is fixed at 1/60 sec and the camera will automatically adjust the iris according to the
level. The iris can be controlled manually but will return to FULL AUTO if there is a zoom or pan/
tilt operation.

• SHUTTER PRIORITY:
The shutter can be varied from 1 sec ?1 /10000 in 22 steps. The camera will automatically adjust
the iris according to the level., If the shutter speed is set to 1/1 or 1/2 sec the iris must be
controlled manually.

AUTO SLOW SHUTTER

• In the FULL AUTO mode the AUTO SLOW SHUTTER feature can be set to ON or OFF. A
camera will automatically set the shutter slower than 1/60 sec according to the level of brightness.

SHUTTER SPEED

• In the SHUTTER PRIORITY mode the shutter can be varied from 1 sec ~ 1/ 10000 in 22 steps.
The camera will automatically adjust the iris according to the level. The iris cannot be controlled
automatically if the shutter speed is set to 1/1 or 1/2 sec. The iris must be controlled manually.

AE COMPENSATION

• AE COMPENSATION can be set from -7 to +7. As the numerical value becomes larger the
screen becomes brighter.

BACK LIGHT COMP

• In the FULL AUTO mode the, BACK LIGHT COMPENSATION feature can be set to ON or OFF.
BACK LIGHT COMPENSATION can be set directly using JK-UC1 Controller (71 PRESET = ON,
72 PRESET = OFF).

Day/Night

• In the FULL AUTO mode the DAY/NIGHT feature can be set AUTO or MANUAL.

• MANUAL mode can be set directly using a JK- UC1 Controller (88 PRESET = Color mode,89
PRESET = monochrome mode).

• An infrared (IR) Cut-Filter can be disengaged from the image path for increased sensitivity in low
light environments. This function will automatically engage depending on the ambient light, allowing
the camera to be effective in DAY/NIGHT environments.

In the SHUTTER PRIORITY mode the AUTO SLOW SHUTTER cannot be set.

Note

In the FULL AUTO mode SHUTTER SPEED cannot be set.

Note

In the SHUTTER PRIORITY mode the BACK LIGHT COMPENSATION feature cannot
be set.

Note

- 15 -

To change the AE options:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

Camera menu.

3. Position the cursor next to AE and press the OPEN button to access the AE menu.

4. Position the cursor next to the desired option and press the OPEN button to move the cursor to

the right.

5. Move the joystick up or down to select option setting.

6. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.7.4 ZOOM CONTROL

Direct

• The zoom feature has 4 varying speeds.

• The zoom feature can be controlled directly for Wide angle or Telephoto angle.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

CAMERA MENU

•A zoom limit can be set to x18, x36, x72, x144, and x216.

• The maximum optical zoom is x18, x36 to x216 are the values for electronic zoom.

To change the zoom limit:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

Camera menu.

3. Position the cursor next to ZOOM LIMIT and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to toggle between zoom limits.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

At the time of SHUTTER PRIORITY mode choice, DAY/NIGHT mode is fixed in
MANUAL.

Note

- 16 -

6.7.5 SHARPNESS

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

CAMERA MENU

The sharpness can be controlled from 0-15, with 15 being the sharpest.

To change the SHARPNESS:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

Camera menu.

3. Position the cursor next to SHARPNESS and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to select the sharpness level.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

buttons.

6.7.6 LINE LOCK CONTROL

The dome camera can be synchronized with the power supply frequency.

Menu

• Line Lock can be set to ON or OFF

• The Line Lock Phase can be set from 40 to 250 degrees.

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

MODE OFF
LINE PHASE 180

LINE LOCK

MAIN MENU CAMERA MENU

- 17 -

To change the LINE LOCK options:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

Camera menu.

3. Position the cursor next to LINE LOCK and press the OPEN button to access the Line Lock

menu.

4. Position the cursor next to the desired option and press the OPEN button to move the cursor to

the right.

5. Move the joystick up or down to select the option setting.

6. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.7.7 PRIVACY ZONE MASKING

This function masks a user defined area that cannot be viewed by the operator. The mask adjusts
with the pan, tilt and zoom of the camera.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>
PRIVACY ZONE

CAMERA MENU

Privacy Masking ON/OFF:
A maximum of 8 zones can be set.

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the

menu.

3. Position the cursor next to PRIVACY ZONE and press the OPEN button to move the cursor to

the right.

4. Move the joystick up or down to set P1 to P8 ON/OFF separately.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

Privacy zone setup:

1. Use a joystick to move where you want to set a privacy zone.

2. Enter 83 preset to access the setup screen.

Displays PRIVACY ZONE > 1
1: the number indicates zone(8 zone can be set.)

3. Press the OPEN button to set ZONE SIZE

Use a joystick to create the privacy zone to mask.

4. Press the OPEN button to set ZONE COLOR

Use a joystick to select the MASK COLOR to either Black/Gray.

5. Press the CLOSE button.

- 18 -

Notes:

1) Masking areas are only rectangles.

2) When using the PTZ function the privacy zone expands 2x vertically and 4x horizontally.

3) Although the privacy zone works in digital zoom, the zone setting is only available in a non-

digital zoom area.

4) It is recommended to set privacy zone bigger than actual masking area.

5) During turbo panning or tilting, the privacy zone may shift depending on the location of the zone.

6.8 PAN/TILT SETUP

6.8.1 AUTO FLIP

The Auto Flip feature allows the tilt to rotate 180 degrees and reposition itself for continuous
viewing of a moving object directly beneath the dome.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To enable AUTO FLIP:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to AUTO FLIP and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to select ON or OFF.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 19 -

6.8.2 PROPORTIONAL P/T

Proportional P/T controls the pan and tilt speeds according to the amount of zoom.
At telephoto settings, the pan and tilt speeds will be slower to keep the image from moving too fast
on the monitor.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To enable PROPORTIONAL P/T:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to PROPORTIONAL P/T and press the OPEN button to move the

cursor to the right.

4. Move the joystick up or down to select ON or OFF.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.8.3 SCAN LIMIT STOPS

When a Scan Limit Stop is reached during random, frame or auto scan, the dome camera will
reverse direction. A Left Scan Limit Stop and Right Scan Limit Stop can be set. The limit stops
must be greater than 10 degrees apart.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TIL T MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

- 20 -

To enable SCAN LIMIT STOPS:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to SCAN LIMIT STOPS and press the OPEN button to move the cursor

to the right.

4. Move the joystick up or down to select ON or OFF.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

To set SCAN LIMIT STOPS:

1. Set SCAN LIMIT STOPS to ON and exit menu.

2. Position the camera for the LEFT LIMIT STOP.

3. Enter 92 preset. SCAN LEFT LIMIT will be displayed on screen.

4. Position the camera for the RIGHT LIMIT STOP. If the right limit stop is less than 10 degrees

from the left limit stop, NOT ACCEPT will be displayed on screen,

5. Enter 93 preset. SCAN RIGHT LIMIT will be displayed on screen.

6.8.4 MANUAL LIMIT STOPS

When a Manual Limit Stop is reached during a manual (joystick) pan, the camera will stop. A Left
Manual Limit Stop and Right Manual Limit Stop can be set. The limit stops must be greater than 10
degrees apart.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To enable MANUAL LIMIT STOPS:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to MANUAL LIMIT STOPS and press the OPEN button to move the

cursor to the right.

4. Move the joystick up or down to select ON or OFF.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

To set MANUAL LIMIT STOPS:

1. Set MANUAL LIMIT STOPS to ON and exit menu.

2. Position the camera for the LEFT LIMIT STOP.

3. Enter 90 preset. MANUAL LEFT LIMIT will be displayed on screen.

- 21 -

4. Position the camera for the RIGHT LIMIT STOP. If the right limit stop is less than 10 degrees

from the left limit stop, NOT ACCEPT will be displayed on screen.

5. Enter 91 preset. MANUAL RIGHT LIMIT will be displayed on screen.

6.8.5 PARK TIME MINUTES

After a programmed number of minutes of inactivity, the dome camera will park to preset 1. T h e
Park Time Minutes can be set from 1 to 720 minutes. Setting it to 0 will disable the feature.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To set PARK TIME MIN:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to PARK TIME MIN and press the OPEN button to move the cursor to

the right.

4. Move the joystick up or down to set the number of minutes.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.8.6 AUTO PATROL

The Auto Patrol feature will repeat a pattern of up to 64 presets. Limit stops are ignored during
Auto Patrol.
The moving speed is fixed at 400 deg/s when the STOP TIME is 10 seconds or more.
However, it will become 90 deg/s if a STOP time is less than 10 seconds.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

- 22 -

To enable AUTO PATROL:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to AUTO PATROL and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to scroll through the presets. Move the joystick left or right to turn

the preset ON or OFF.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.8.7 SCAN SPEED

The SCAN SPEED for auto scan, random scan and frame scan can be set from 1-90 degrees/sec.
However, this speed is limited by MAX SPEED setting.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To set SCAN SPEED:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to SCAN SPEED and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to set the speed.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 23 -

6.8.8 SCAN TILT ANGLE

The tilt angle of the dome camera for auto scan, random scan and frame scan can be set from 0 to
85 degrees or 92 degrees (0 degree is straight down).

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To set SCAN TILT ANGLE:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to SCAN TILT ANGLE and press the OPEN button to move the cursor

to the right.

4. Move the joystick up or down to set the tilt angle.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.8.9 STOP TIME

During frame scan, random scan or auto patrol, a stop time from 1 sec to 60 sec can be set. During
scanning, the camera will not move for the specified time at each stop.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

- 24 -

To set STOP TIME:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to STOP TIME and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to set the stop time.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.8.10 MAX SPEED

The maximum speed of Pan/Tilt functions can be set from 30 degrees/sec to 400 degrees/sec. The
max speed controls global Pan/Tilt speeds. To reduce rotation noise use a lower speed.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU PAN/TILT MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

To set MAX SPEED:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/

Tilt menu.

3. Position the cursor next to MAX SPEED and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to set the maximum speed.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 25 -

6.9 PRESET TITLES SETUP

Titles can be set for up to 64 presets (pan/tilt position and zoom). Titles can be up to 20 characters
in length and can be displayed at the top or bottom of the screen.

Menu

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

MAIN MENU

TITLE INPUT
1
TITLE POSITION UP

TITLE MENU

To set PRESET TITLES:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to PRESET TITLES and press the OPEN button to access the Title

menu.

3. Press the OPEN button to move the cursor down to the title number. Move the joystick up or

down to scroll through title numbers.

4. Move the joystick to the right to input the title. Move the joystick up or down to scroll through

characters.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6. Move the joystick down to TITLE POSITION and press open to choose UP or DOWN position of

the title. UP will display the title at the top of the screen and DOWN will display the title at the
bottom of the screen.

7. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 26 -

6.10 OTHERS MENU

6.10.1 POWER UP

During Power-Up, the dome camera can be set to start in various modes.
PARK: The dome camera moves to Preset 1 position.
AUTO SCAN: The dome camera performs an auto scan operation.
FRAME SCAN: The dome camera performs a frame scan operation.
RANDOM SCAN: The dome camera performs a random scan operation.
AUTO PATROL: The dome camera performs an auto patrol operation.
DEFAULT : The dome camera moves to the mechanical reset point.

Menu

MAIN MENU

POWER UP PARK
FREEZE ACTIVITY ON
LOAD FACTORY DEFAULT
TILT ANGLE OUTDOOR

OTHERS MENU

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

To set POWER UP MODE:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to OTHERS and press the OPEN button to access the menu.

3. Position the cursor next to POWER UP and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to set the power up mode.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 27 -

6.10.2 FREEZE ACTIVITY

During frame scan, random scan or auto patrol, camera images will not be shown while the dome
camera moves from the current position to the next position.

Menu

MAIN MENU

POWER UP PARK
FREEZE ACTIVITY ON
LOAD FACTORY DEFAULT
TILT ANGLE OUTDOOR

OTHERS MENU

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

To set STOP TIME:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to OTHERS and press the OPEN button to access the menu.

3. Position the cursor next to FREEZE ACTIVITY and press the OPEN button to move the cursor

to the right.

4. Move the joystick up or down to set freeze activity to ON or OFF.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

6.10.3 LOAD FACTORY DEFAULTS

The factory default settings can be loaded.

Menu

MAIN MENU

POWER UP PARK
FREEZE ACTIVITY ON
LOAD FACTORY DEFAULT
TILT ANGLE OUTDOOR

OTHERS MENU

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

To set LOAD FACTORY DEFAULT:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to OTHERS and press the OPEN button to access the menu.

3. Position the cursor next to LOAD FACTORY DEFAULT and press the OPEN button twice to load

factory default settings.

- 28 -

6.10.4 TILT ANGLE

Set up the Tilt angle according to the housing used and the purpose.
Indoor - 85 degrees MAX
Outdoor - 92 degrees MAX

Menu

MAIN MENU

POWER UP PARK
FREEZE ACTIVITY ON
LOAD FACTORY DEFAULT
TILT ANGLE OUTDOOR

OTHERS MENU

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

To set TILT ANGLE:

1. Enter the preset command to access the main menu.

Refer to section 6.1 for the controller model and preset command.

2. Position the cursor ( ) next to OTHERS and press the OPEN button to access the menu.

3. Position the cursor next to TILT ANGLE and press the OPEN button to move the cursor to the

right.

4. Move the joystick up or down to set the tilt angle mode.

5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE

button.

- 29 -

7. Menu Directory

<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT

TOP MENU

<FOCUS>
WB ATW
<AE>
ZOOM LIMIT X18
SHARPNESS 10
<LINE LOCK>

PRIVACY ZONE P1→OFF

CAMERA SETUP MENU

TITLE INPUT
1
TITLE POSITION DOWN

PRESET TITLES MENU

OTHERS MENU

AUTO FLIP ON
PROPORTIONALP/T ON
SCAN LIMIT STOPS OFF
MANUAL LIMIT STOPS OFF
PARK TIME MIN 0MIN
AUTO PAT RO L P1→OFF
SCAN SPEED 5DEG./S
SCAN TILT ANGLE 30DEG.
STOP TIME 10SEC
MAX SPEED 400DEG/S

PAN/TILT SETUP MENU

MODE AUTO
ACTIVE TIME 5S
INTERVAL TIME 5S
SENSITIVITY NORMAL

FOCUS SETUP MENU

AE MENU

MODE FULL AUTO
AUTO SLOW SHUTTER OFF
SHUTTER SPEED 1/60
AE COMPENSATION 0
BACK LIGHT COMP OFF
DAY/NIGHT AUTO

POWER UP PARK
FREEZE ACTIVITY OFF
LOAD FACTORY DEFAULT
TILT ANGLE OUTDOOR

MODE OFF
LINE PHASE 180

LINE LOCK MENU

- 30 -

7.1 MENU LIST AND SETTINGS

TopMenu

SubMenu1 SubMenu2

Contents

Default

CAMERA
SETUP

FOCUS

WHITE BALANCE

AUTO EXPOSURE

----

AUTO / MANUAL / ZOOM
TRIGGER / INTERVAL

MODE

ACTIVE TIME

5S

ALL OFF

AUTO

1〜255S

INTERVAL TIME

5S

1〜255S

SENSITIVITY

NORMAL

AT W

NORMAL / LOW
AUTO / ATW / ONE PUSH WB

ZOOM LIMIT

----

x18

x18 / 36 / 72 / 144 / 216

SHARPNESS

----

10

0〜15

LINE LOCK

MODE

OFF

ON / OFF

LINE PHASE

180

40〜250

PRIVACY ZONE

----

P1→OFF

P1〜P8

SCAN SPEED

----

5

1〜90 DEGREE / S

SCAN TILT ANGLE

----

30

0〜92 DEGREE

STOP TIME

----

10

1〜60 SEC

MAX SPEED

----

400

30〜400 DEGREE / S

FREEZE ACTIVITY

----

OFF

ON / OFF

TITLE POSITION

----

DOWN

UP / DOWN

POWER UP

----

PARK

DEFAULT / PARK / AUTO SCAN /
FRAME SCAN / RANDOM SCAN /
AUTO PAT RO L

TITLE INPUT

---­AllBlank

Itisto20characterstoeach
Presetnumber.

LOAD FACTORY
DEFAULT

----

AUTO FLIP

----

ON

ON / OFF

PROPORTIONAL P/T

----

ON

ON / OFF

SCAN LIMIT STOPS

----

OFF

ON / OFF

MANUAL LIMITS STOPS

----

OFF

ON / OFF

PARK TIME MINUTES

----

0

0〜720MIN

AUTO PAT RO L

----

MODE

FULL AUTO

FULL AUTO / SHUTTER PRIORITY

AUTO SLOW SHUTTER

OFF

ON / OFF

SHUTTER SPEED

1 / 60

1 / 1〜1 / 10000（22 step）

AE COMPENSATION

0

-7〜+7

BACK LIGHT COMP.

OFF

ON / OFF

DAY / NIGHT

AUTO

AUTO /MANUAL

PRESET1=ON / OFF
PRESET2=ON / OFF

PRESET66=ON / OFF

TILT ANGLE

INDOOR/OUTDOOR

OUTDOOR

PAN / TILT
SETUP

PRESET
TITLES

OTHERS

- 31 -

8. Switch Setting

There are three switches which must be set up. Switch 1 sets the camera address. Switch 2 sets
the protocol and bit rate. Switch 301 sets the termination – only used on the last daisy chained
camera.

DIP switch

Dip switch (SW1 & SW2)
It is necessary to set a unique camera address and protocol.
Set up a camera address according the following table.

- 32 -

(1) SWI : Camera Address

bit1

On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off

1

bit2

Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On

2

bit3

Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off

4

bit4

Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
Off
Off
Off

8

bit5

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On

16

bit6

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On

32

bit7

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off

64

bit8

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off

128

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

bit1

On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On

Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On

1

bit2

On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off

Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On

2

bit3

Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On

On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
Off
Off
On
On
On
On

4

bit4

Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off

Off
Off
Off
Off
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On

8

bit5

On
On
On
On
On
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On

16

bit6

On
On
On
On
On
On
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off

On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On

32

bit7

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On

On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On

64

bit8

Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off

On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On

128

51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69

228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255

SW1 SW1

SWValue

Camera
Address

Camera
Address

SWValue

- 33 -

Camera Address = 1 × bit 1 Status + 2 x bit 2 Status + 4 × bit 3 Status + 8 × bit 4

Status + 16 × bit 5 Status +32 × bit 6 Status + 64 × bit 7
Status + 128 × bit 8 Status

* bit Status: On = 1, Off = 0
ex) Camera Address 228 = 1 × 0 (Off) + 2 × 0 (Off) + 4 × 1 (On) + 8 × 0 (Off) + 16 × 0

(Off) + 32 × 1 (On) + 64 × 1 (On) + 128 × 1 (On)

=4 + 32+ 64 + 128 + 228 → Off/Off/On/Off/Off/On/On/On

Set up the protocol and bit rate to match the controllers settings.

(2) SW2 (bit 1 - 2) Protocol

bit1

Off
On
Off
On

bit2

Off
Off
On
On

TOSHIBA-P
TOSHIBA-D
Reserve1
Reserve2

Protocol

(3) SW2 (bit3 - 4) Bit Rate

bit3

Off
On
Off
On

bit4

Off
Off
On
On

1200bps
2400bps
4800bps
9600bps

Protocol

(Dome base switch:S301)
This is RS422 termination switch located near the BNC connector.
In daisy chain operation system, the farthest dome from the controller is turned ON.
For example, when the controller is connected with three dome cameras in the direct mode,
the only furthest dome camera from a controller is turned ON. The other dome camera is
turned OFF. (It is OFF at the time of shipment.)
ON and OFF are as in a figure.

ON

S301

OFF

BNC Connector

POWER
TERMINAL

- 34 -

9. Installation

JK-H01A is a housing for ceiling mount of the Toshiba dome camera.

1. IK-DP30A Installation procedure
(1) Carefully inspect to insure all parts

are present and remove all parts
from the box.

(2) A template is included for ease in

cutting the mounting hole. First,
locate a position in the ceiling for
a 9.020.08" (2292mm) hole to be
drilled. Trace around the template,
then cut a hole in the ceiling
following the trace lines. [Note: The
thickness of a ceiling to which this
housing can be attached is 0.08-

1.77" (2-45mm).]

(3) Remove the dome cover. To

separate the dome cover from the
housing, turn the cover to the left
with both hands. This dome cover
is connected to the top housing
with the wire. Fig-1

(4) Loosen the lock screw according

to ceiling board thickness for
attaching to the ceiling.

(5) Install the camera mounting

screws that came with the camera.
Do not fully tighten the screws.

Lock
screw

Lock
screw

Fig-1

- 35 -

(JK-H01A top housing install)

(6) Move the two support arms inside. Fig-2
(7) Remove knockout in the center of the housing

and let the cable pass through.

(8) Put the video cable, power cable, and the

communication cable inside the housing from
the hole on the topside.

(9) Insert the camera housing into the ceiling. Push

out the support arms so that they hold onto the
ceiling. Fig-3

(10) Tighten the two support arm screws to secure

the camera housing to the ceiling. Fig-4

Support wire
is fixed here

Support Arms

Fig-3

Fig-4

Lock
screw

Lock
screw

Support
Arms

Fig-2

- 36 -

(IK-DP30A dome base install)

(11) Attach the video cable (included with the dome

accessories) to the video connector of a dome
base. [Note: Do not connect a thick coaxial cable
to a dome camera. There is a possibility of
damaging a connector. Be sure to use the cable
included in the dome accessories.]

(12) Communication cables are directly inserted in

the terminal of the dome base.

(13) Tighten the screw to secure the dome base to

the housing. Fig-5 qwe

(IK-DP30A dome drive install)

(14) After setting up DIP-SW in the top of the dome (See

8.Switch setting), connect the support wire to the hook of
the dome base. Fig-6 q

(15) To lock the dome drive to the dome base, line up the

notch with the label and turn to the right with both
hands. Fig-6 w

Ensure that the location of the notch (position of yellow paint) on the
dome base and the location of the installation label on the dome
drive are aligned.

(JK-H01A dome cover install)

(16) To lock the dome cover, insert the support wire and turn to the right with both hands.

Fig-7, Fig-8

Fig-7

Fig-8

(17) The installation is complete.

FIg-5

q

w

e

Fig-6

q

w

- 37 -

10. Specifications

Overall

Temperature of operation 32° to 122°F (0° to 50°C)

Preservation temperature –4° to 140°F (–20° to 60°C)

Weight 1.8 kg

Power supply AC24 V ±10% 60 Hz

Power consumption 20 W

Camera

Image Sensor 1/4 type IT CCD (High Sensitive CCD)

Number of Effective Pixels 768(H) × 494(V)

Lens 18 × Zoom f = 4.1 to 73.8 mm (F1.4 to F3.0)

Digital Zoom 12 × (216 × with optical zoom)

Angle of View (H) approx. 48degree (wide limit)

approx. 2.7degree (tele limit)

Sync. System Internal/Line lock (AC Line lock phase adjustable)

Min. Illumination 0.7 lux typ. (1/60), 0.05 lux typ (1/4)

0.01 lux (1/4, IR Cut OFF)

S/N Ratio more than 50 dB

Resolution 480 TV lines (typ)

Electronic Shutter 1/4 to 1/10000 sec.

White Balance Auto, ATW, One Push WB

Gain Auto

AE Control Full Auto, Shutter Priority, Manual

Back Light Compensation On/Off

Auto Slow Shutter On/Off (On: max 1/4sec.)

Focusing System Auto, Interval, Zoom Trigger, Manual

Video Output NTSC, VBS: 1.0 Vp-p (Sync Negative), 75 ohm

Privacy Zone Masking 8 positions

- 38 -

Mechanical

Pan Range 360 degrees continuous

Tilt Range 92 degrees (Outdoor)

Manual Pan Speeds 0.1° - 90°/s

Manual Pan Speeds (turbo) 150°/s

Manual Tilt Speeds 0.1° - 45°/s

Preset Speeds Pan: 400°/s

Tilt: 200°/s

Proportional P/T Provided

Remote Control

I/F RS-422 (receive only)

Protocol Toshiba-P/D (Dip sw selectable)

Data rate 1200, 2400, 4800, 9600bps (Dip sw selectable)

LIMITED WARRANTY

CCD SECURITY DOME CAMERA IK-DP30A

The Imaging System Division (“ISD”) of Toshiba America Information Systems, Inc makes the following limited warranties with regard to
this CCD Camera model IK-DP30A(“Product”). These limited warranties extend to the Original End-User (“You[r]”).

Three (3) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a
period of three (3) years from the date of purchase by the Original End-User. During this three (3) year period, ISD will repair or replace the
Product, if it does not perform as warranted. In order to take advantage of this Limited Warranty. You must: (a) call [phone] to
receive a RMA number: and (b) pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange
Center. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.

Instruction Manual (Owner’s Manual): You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this
Product. Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and
follow the instructions to correct the problem.

How to Obtain Warranty Service Step-by-step Procedures: To obtain warranty service. You should:

1. Contact Toshiba at [phone] to first verify operation or installation assistance. (877) 855-1FIX

2. If technical support determines that the unit is defective, an RMA will be issued with return instructions for repair.

3. Securely pack the Product in the original carton and external shipping pack, include a letter explaining the problem with a copy of the

bill of sale or proof of purchase.

4. Prepay all transportation and insurance costs.

Your Responsibilities: This Limited Warranty is subject to the following conditions:

1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.

2. You must notify [phone] within (30) days after you discover that the product does not perform in accordance with specifications

during the Limited Warranty period.

3. You must pack the Product in its original carton using the original packing material. Then insert the original carton containing the

Product into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center.

DISCLAIMERS:
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS. SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY
SHALL BE THE REPAIR OF REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP
BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT.
THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS,
LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH
OF CONTRACT, TORT OR OTHERWISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT,
EVEN IF TAIS, ITS PARENT COMPANY, OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY
CLAIM BY ANY OTHER PARTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM
STATE TO STATE.

THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE, ABUSE,
ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S WRITTEN INSTRUCTIONS,
OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR AUTHORIZATION, OR UPON THE
REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION,
SET UP AND ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY

No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the terms of this
Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising
under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the
date You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law.
Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law, so the above
provision may not apply to You. This Limited Warranty gives You specific legal rights and You may also have other rights which vary from
state to state.

TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

Imaging Systems Division

V2.0