Toshiba 65NH84 User Manual

OWNER'S MANUAL

Projection Television

Introduction

your TV

Connecting

Using the

Remote Control

Owner's Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model:

your TV

Setting up

Features

Using the TV’s

Appendix

65NH84

Serial No.:

Index

23566433

Dear Customer,



Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV.

Before operating the TV, please read this manual completely, and keep it nearby for future reference.

Safety Precautions

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. DO NOT TRY TO SERVICE  THIS PRODUCT YOURSELF.

 The exclamation mark in the triangle tells you that 

important operating and maintenance instructions  follow this symbol.

NOTE TO CATV INSTALLERS IN THE USA

This is a reminder to call the CATV system installer’s attention to Article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 26 and 27 on page 4.

NOTICE OF POSSIBLE ADVERSE EFFECTS

ON TV PICTURE TUBE

If a fixed (non-moving) pattern remains on the TV screen for long periods of time, the image can become permanently engrained in the picture tube. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 34 on page 4.

ENERGY STAR® qualified TV. Products that earn the ENERGY STAR prevent green house gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy. ENERGY STAR and the ENERGY STAR mark are registered U.S. marks.

Child Safety

It Makes A Difference Where Your TV Stands

Congratulations on your purchase! As you enjoy your new TV, keep these safety tips in mind:

The Issue

 If you are like most consumers, you have a TV in your home.

Many homes, in fact, have more than one TV.

 The home theater entertainment experience is a growing

trend, and larger TVs are popular purchases; however, they are not always supported on the proper TV stands.

 Sometimes TVs are improperly secured or inappropriately

situated on dressers, bookcases, shelves, desks, audio speakers, chests, or carts. As a result, TVs may fall over, causing unnecessary injury.

Toshiba Cares!

 The consumer electronics industry

is committed to making home

entertainment enjoyable and safe.

 The Consumer Electronics

Association formed the Home

Entertainment Support Safety

Committee, comprised of TV and consumer electronics furniture

manufacturers, to advocate

children’s safety and educate

consumers and their families about

television safety.

Tune Into Safety

 One size does NOT fit all! Use appropriate

furniture large enough to support the weight of your

TV (and other electronic components).

 Use appropriate angle braces, straps, and anchors to secure

your furniture to the wall (but never screw anything directly into the TV).

 Carefully read and understand the other enclosed

instructions for proper use of this product.

 Do not allow children to climb on or play with furniture

and TVs.

 Avoid placing any item on top of your TV (such as a VCR,

remote control, or toy) that a curious child may reach for.

 Remember that children can become excited while watching

a program and can potentially push or pull a TV over.

 Share our safety message about this hidden hazard of

home with your family and friends. Thank you!

2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org

CEA is the Sponsor, Producer and Manager of the International CES

the

2 0303

Important Safety Instructions

QUALIFIED

SERVICE

TECHNICIAN

Installation, Care, and Service

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near

water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during

lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

Wide plug

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

16) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

17) DANGER: RISK OF SERIOUS PERSONAL

INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on

an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

18) Never place or store the TV in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C).

19) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit.

20) Never place items such as vases, aquariums, or candles on top of the TV.

21) Always place the back of the television at least one (1) inch away from any vertical surface (such as a wall) to allow proper ventilation.

22) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar

surface;

• too close to drapes, curtains,

or walls; or

• in a confined space such as a

bookcase, built-in cabinet, or any other place with poor ventilation.

The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV.

23) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

24) Never overload wall outlets and extension cords.

0303 3

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Power service grounding electrode system (NEC Art 250 Part H)

Ground clamps

Antenna lead-in wire

Electric service equipment

QUALIFIED

SERVICE

TECHNICIAN

25) Always operate this equipment from a 120 VAC, 60 Hz power source only.

31) [This item applies to projection TVs only.] If the air temperature rises suddenly (for example, when the TV is first delivered), condensation may form on the lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the TV for 6 to 7 hours to allow the condensation to evaporate.

26) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

27) DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH!

• Use extreme care to make sure you are never in

a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

32) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

33) During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

) Possible Adverse Effects on TV Picture Tube: If a fixed

(non-moving) pattern remains on the TV screen for long periods of time, the image can become permanently engrained in the picture tube and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your TV on for long periods of time while it is displaying the following formats or images:

• Fixed Images, such as PIP/POP windows, stock tickers,

video game patterns, TV station logos, and websites.

• Special Formats that do not use the entire screen. For

example, viewing letterbox style (16:9) media on a normal (4:3) display (gray bars at top and bottom of screen); or viewing normal style (4:3) media on a widescreen (16:9) display (gray bars on left and right sides of screen).

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

28) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen. Turn the TV off to check for reflections on the screen, and then remove the source of reflections while viewing the TV.

29) Always unplug the TV before cleaning. Never use liquid or aerosol cleaners. Clean only with a dry cloth.

30) WARNING: RISK OF ELECTRIC SHOCK!

4 0303

Never spill liquids or push objects of any kind into the TV cabinet slots.

Service

35) WARNING: RISK OF ELECTRIC SHOCK! Never attempt to service the

TV yourself. Opening and

removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to a Toshiba Authorized Service Center.

36) If you have the TV serviced:

• Ask the service technician to use only replacement parts

specified by the manufacturer.

• Upon completion of service, ask

the service technician to perform routine safety checks to determine that the TV is in safe operating condition.

37) When the TV reaches the end of its useful life, ask a

qualified service technician to properly dispose of the TV. Improper disposal may result in a picture tube implosion and possible personal injury.

Important Safety Precautions for Split Cabinet Feature

This Toshiba TV model has a split cabinet feature that allows disassembly of the cabinet into two sections during installation.

For details, please refer to the insert titled “Disassembly/ Reassembly Instructions for Split Cabinet Feature” that accompanied this owner’s manual in the accessory pack. If you do not have the insert, you can download a copy of it from our Web site (www.toshiba.com/tacp in the U.S.A. or www.toshiba.ca in Canada). If you do not have access to the Internet, call 1-800-631-3811 in the U.S.A. or 1-800268-3404 in Canada.

WARNING: If you split the cabinet for any purpose, NEVER energize the bottom section until it is completely and properly installed.

Energizing the disassembled bottom section and subjecting it to intentional misuse (for example, exposing it to a foreign object) creates the potential for an electrical shock hazard that could result in death or serious injury.

CAUTION: If you use the split cabinet feature, ALWAYS

handle and treat the top section of the TV cabinet, which contains a glass mirror, with great care. If subjected to excessive mechanical abuse (for example, if bumped or dropped), the mirror may break, creating exposed glass fragments with sharp edges. Contact with these glass fragments may result in injury.

Installation, Care, and Service

CAUTION: The split cabinet feature allows disassembly of

the cabinet into two sections during installation. If you use the split cabinet feature, follow these precautions while the two sections of the TV cabinet are disassembled:

1) Always handle and treat the top section of the TV cabinet (with the viewing screen), which contains a glass mirror, with great care. If subjected to excessive mechanical abuse (for example, if bumped or dropped), the mirror may break, creating exposed glass fragments with sharp edges. Contact with these glass fragments may result in injury.

2) Never temporarily locate the disassembled bottom section in an area where it may be exposed to foreign objects or abuse (for example, areas where children may be playing, where items may fall on top of the unit, or where liquids may spill into the unit). Failure to follow this instruction may result in damage to the optic components of the TV. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY.

3) Always keep the top and bottom sections of the TV cabinet in an upright position while disassembled. Failure to follow this instruction may result in damage to the TV, including but not limited to the optic components, cabinet, bezel, and glass mirror. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY.

4) Never energize the bottom section of the TV cabinet

while disassembled. Failure to follow this instruction could result in death or serious injury.

5) Never place anything on top of the disassembled bottom section of the TV cabinet. Failure to follow this instruction may result in damage to the optic components. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY.

6) Never store or transport the unit while it is disassembled. Failure to follow this instruction may result in damage to the TV, including but not limited to the optic components, cabinet, bezel, and glass mirror. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY.

0303 5

Important Safety Information ............................. 2-5

Introduction................................................................ 7

Welcome to Toshiba......................................................... 7

Exploring your new TV ................................................... 7

Connecting your TV .................................................. 8

Connecting an antenna or cable TV................................. 8

Connecting a VCR .......................................................... 9

Connecting a cable converter box .................................... 9

Connecting a cable converter box and VCR................... 10

Connecting a DVD player or satellite receiver and

a VCR............................................................................ 11

Connecting a DVD player with ColorStream

(component video) and a VCR ...................................... 12

Connecting a DTV receiver/set-top box with

ColorStream

(component video) and a VCR................ 13

Connecting two VCRs ................................................... 14

Connecting a camcorder ................................................ 14

Connecting an HDMI™ or a DVI device to

the HDMI input ........................................................... 15

Connecting an audio system .......................................... 16

Using the remote control ...................................... 17

Preparing the remote control for use .............................. 17

Installing the remote control batteries ............................ 17

Remote Control functional key chart ...................... 18

Programming the remote control for use with

your audio/video devices ................................................ 20

Device code setup ................................................... 20

Searching and sampling the code

of a device [8500] ................................................... 20

Using the volume lock feature [8000] ..................... 21

Operational feature reset [8900] ............................. 21

Device code table .................................................... 22

Learning about the remote control .......................... 24

Setting up your TV .................................................. 25

Learning about the menu system ................................... 25

Changing the on-screen display language ....................... 26

Selecting the antenna input ............................................ 26

Adding channels to the TV’s memory ............................ 27

Programming channels automatically...................... 27

Adding and erasing channels manually.................... 28

Changing channels ........................................................ 28

Adjusting the color convergence..................................... 29

Automatically adjusting the color convergence

using TouchFocus™ ............................................... 29

Manually adjusting the color convergence............... 29

Using the TV’s features.......................................... 31

Adjusting the channel settings ........................................ 31

Switching between two channels using Channel

Return .................................................................... 31

Switching between two channels using

SurfLock™............................................................. 31

Programming your favorite channels ....................... 31

Labeling channels ................................................... 33

Viewing the wide-screen picture formats

(480i, 480p and 1080i signals only) ............................ 34

Selecting the picture size ......................................... 34

Scrolling the Theater Wide picture

(Theater Wide 2 and 3 only) .................................. 36

Using the AUTO ASPECT feature ......................... 37

Using the POP double-window feature .......................... 38

Switching the main and POP pictures..................... 39

Switching the speaker audio (main or POP)............ 39

Double-Window aspect ratio .................................. 40

Using the programmed channel search function............. 40

Using the favorite channel search function .............. 41

About the auto favorite feature................................ 41

Using the LOCKS menu ............................................... 42

Entering the PIN code ............................................ 42

If you cannot remember your PIN code .................. 42

Using the V-CHIP menu ............................................... 42

ENABLE BLOCKING .......................................... 43

TV RATING (Independent rating system for

broadcasters) ........................................................... 43

MPAA RATING (Independent rating system for

movies) ................................................................... 44

BLOCKING OPTION .......................................... 44

Unlocking programs temporarily ............................ 45

Locking channels ........................................................... 45

Locking the video inputs................................................ 47

Changing the PIN code ................................................. 47

Adjusting the picture ..................................................... 48

Selecting the picture mode ...................................... 48

Adjusting the picture quality ................................... 48

Saving your new preferences ................................... 49

Selecting the color temperature ............................... 49

Using the CableClear™ DNR feature .................... 50

Resetting picture adjustments ................................. 51

Selecting the display format

(for 480p signals only) ............................................ 51

Selecting the cinema mode ...................................... 51

Selecting the video input source ..................................... 52

Labeling the video input sources .................................... 52

Using the closed caption feature..................................... 53

Setting the ON timer ..................................................... 54

Setting the sleep timer.................................................... 54

Setting the clock ............................................................ 55

Adjusting the sound ....................................................... 56

Muting the sound ................................................... 56

Selecting stereo/SAP broadcasts .............................. 56

Using the WOW™ surround sound feature ........... 57

Adjusting the sound quality .................................... 57

Resetting your audio adjustments ........................... 58

Using the StableSound

feature .............................. 58

Turning off the built-in speakers ............................. 59

Selecting the Audio OUT sound ............................. 59

Selecting the background of the menu display ............... 60

Displaying on-screen information .................................. 60

Understanding the auto power off feature ...................... 60

Understanding the last mode memory feature ................ 60

Appendix ................................................................... 61

Specifications ................................................................. 61

Troubleshooting............................................................. 62

Limited United States Warranty..................................... 63

Limited Canada Warranty .............................................. 64

Index .......................................................................... 65

Introduction

Welcome to Toshiba

Congratulations! You have purchased one of the finest projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible.

Instructions in this manual are based on using the remote control. You can also use the controls on the TV if they have the same name as those on the remote control.

Please read all the safety and operating instructions carefully, and keep the manual for future reference.

Exploring your new TV

You can operate your TV using the buttons on the front panel or the remote control. The terminals for connecting other equipment to your TV are on the back panel and front panel (behind the door). See “Connecting your TV” on page 8.

Front

Lift up

Back

Remote sensor

POWER

indicator

(Behind the screen)

Volume x • Channel zy

Power

VOLUME

CHANNEL

EXIT

TouchFocus™

TouchFocus

TV/VIDEO

EXITMENU

TV/VIDEO

ANT-2 IN

S-VIDEO

Video/audio inputs

(behind the door)

ANT OUT

ANT-1 IN

L/MONO

VIDEO

AUDIO

Video 3

Please push TouchFocus

button after setup

Convergence may drift as a result of moving the TV or adjusting its position. The TouchFoucas automatically adjusts the TV’s color convergence. It is recommended that you set convergence by pressing the TouchFoucus button on the TV’s front panel. To manually adjust the color convergence, see page 29.

system

Remote control

LIGHT SLEEP

CABLE/SAT VCR DVD

123

AUDIO1 AUDIO2

456

MODE

789

PIC SIZE

+10

100/

ACTION

DVD RTN CH RTN

POP CH

SLOW/DIR

TV/

VCR

DVD CLEAR

INPUT

PAUSE/STEP

AM/FM DISC

SPLIT

SWAP

FAV

ENTER

FAV

EXIT

POP DIRECT CH

CH SCAN

POWER

VOL

RECALL

MUTE

SKIP/SEARCH

PLAYREW FF

STOP

FREEZE

SOURCE

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

ENT

Features

Using the TV’s

REC

VIDEO 1/2

ColorStream

HD1/HD2

HDMI IN

Variable Audio OUT

Audio OUT

Appendix

CT-90164

Index

Connecting your TV

Note: Cables are not supplied with your TV.

Introduction

your TV

Connecting

●

Coaxial cable is the cable that comes in from your antenna, cable TV service, or cable converter box. Coaxial cable uses “F” connectors.

Standard A/V (audio/video) cables usually come in sets of three, and are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. On your TV’s back panel, the standard A/V inputs are color-coded in the same manner as the cables.

S-Video cable is for use with video equipment with S-Video output. Component video cables come in sets of three, and are for use with

video equipment with component video output. (ColorStream® is Toshiba’s brand of component video.)

HDMI is for use with video equipment with HDMI output (type A connectors) (see page 15).

Coaxial (antenna) cable

Standard A/V cables (red/white/yellow)

S-video cable

Component video cables

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Connecting an antenna or cable TV

This connection allows you to watch TV programs or basic cable channels.

From Antenna or Cable

HDMI cable

NOTICE: RISK OF EQUIPMENT DAMAGE.

Do not plug in any power cords until you have finished connecting all equipment.

Appendix

Index

Connecting a VCR

This connection allows you to watch local channels and video programs, play or record on the VCR while watching TV, and record from one channel while watching another channel.

You will need:

• two coaxial cables

• one set of standard A/V cables

From Cable Box or Antenna

Stereo VCR

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a VCR with S-video, use an Svideo cable (in the S-video jacks) instead of the standard video cable.

Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Introduction

your TV

Connecting

Using the

Remote Control

Connecting a cable converter box

This connection allows you to watch basic and premium cable channels To watch basic cable and use the TV’s features, select ANT-1. To view

premium channels, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• three coaxial cables

From Cable

INOUT

Note:

When you use a converter box with your TV, the remote control will not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

your TV

Setting up

Features

Using the TV’s

Appendix

Cable converter box

Index

Connecting a cable converter box and VCR

This connection allows you to watch and record basic and premium cable channels, watch videotapes, and record one channel while

Introduction

your TV

Connecting

Using the

Remote Control

watching another channel. To watch basic cable and use the TV’s features, select ANT-1. To view premium channels or record with the VCR, select ANT-2, tune the TV and VCR to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• four coaxial cables

• one set of standard A/V cables

From Cable

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a VCR with S-video, use an Svideo cable (in the S-video jacks) instead of a standard video cable. Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

When you use a converter box with your TV, the remote control will not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

your TV

Setting up

Features

Using the TV’s

Appendix

IN from ANT OUT to TV CH 3

CH 4

Stereo VCR

VIDEO

OUT

AUDIO

INOUT

Cable converter box

Index

Connecting a DVD player or satellite receiver and a VCR

This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel.

You will need:

• two (or three, if satellite receiver is used) coaxial cables

• one set of standard A/V cables (between the TV and VCR) (plus one additional set of standard A/V cables if satellite receiver is used)

• one S-video cable (between the TV and DVD player/satellite receiver)

• one pair of standard audio cables (between the TV and DVD player/satellite receiver)

Stereo VCR

OUT

AUDIO

From

Antenna

IN from ANT OUT to TV CH 3

CH 4

VIDEO

Note:

For the highest possible picture quality from a DVD player or satellite receiver without component video or HDMI, use an S-video cable. (If your DVD player has component video, see page 12. If your DVD player or satellite receiver has HDMI or DVI, see page

15.)

Do not connect both an S-video cable and a standard video cable between the TV and DVD player/satellite receiver at the same time or the picture performance will be unacceptable.

Do not connect the DVD player/satellite receiver and VCR to the same set of Video inputs on the TV. (See the illustrations, which show the DVD player/satellite receiver connected to Video-1 on the TV, and the VCR connected to Video-2 on the TV.)

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

From

Satellite

Dish

IN from ANT

S-VIDEO

VIDEO

OUTOUT

VIDEO

OUTOUT

DVD Player

AUDIO

OUT

Satellite Receiver

AUDIO

OUT

Features

Using the TV’s

Appendix

Index

Connecting a DVD player with ColorStream (component video) and a VCR

This connection allows you to watch DVD, VCR, and TV programs,

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

and record TV programs. Your TV has ColorStream

your TV to a DVD player with component video (such as a Toshiba DVD player with ColorStream and realism.

– To record one TV program while watching another TV program,

– To record a TV program while watching a DVD, tune the VCR to

You will need:

From Antenna

(component video) inputs. Connecting

) can greatly enhance picture quality

tune the VCR to the channel to record, and tune the TV to the channel to watch.

the channel to record, and select ColorStream HD1 on the TV (see “Selecting the antenna input” on page 26).

• two coaxial cables

• one set of standard A/V cables

• one pair of standard audio cables

• one set of component video cables

Stereo VCR

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DVD player.

You can connect the component video cables to either set of ColorStream jacks on the TV (HD1 or HD2).

For HDMI or DVI connection, see page 15.

The ColorStream HD1/HD2 and HDMI jacks can be used with Progressive (480p, 720p) and Interlaced (480i,1080i) scan systems; however, a 1080i signal will provide the best picture performance.

If your DVD player is not compatible with component video, HDMI, or DVI, use the S-video connections (plus the standard audio connections) instead (see page 11).

Features

Using the TV’s

Appendix

Index

PRPBY

S-VIDEO

COMPONENT VIDEO

DVD player with component video

VIDEO

OUT

AUDIO

OUT

Connecting a DTV receiver/set-top box with

ColorStream

This connection allows you to watch DTV (digital TV), VCR, and TV programs, and record DTV and TV programs.

Your TV has ColorStream (component video) inputs. Connecting your TV to a DTV receiver with component video can greatly enhance picture quality and realism.

– To record and watch a DTV program, select LINE IN on the

VCR, and select ColorStream HD2 (or VIDEO 1 for a nonColorStream connection) on the TV (see “Selecting the antenna input” on page 26).

– To record a TV program while watching a DTV program, tune the

VCR to the channel to record, and select ColorStream HD2 on the TV.

– To record and watch the same TV program, tune the VCR to the

channel to record, and select VIDEO 1 on the TV.

– To record one TV program while watching another TV program,

tune the VCR to the channel to record, and tune the TV to the channel to watch.

You will need:

• three coaxial cables

• two sets of standard A/V cables

• one pair of standard audio cables

• one set of component video cables

(component video) and a VCR

Note:

For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DTV receiver/set-top box.

You can connect the component video cables to either set of ColorStream jacks on the TV (HD1 or HD2).

For HDMI or DVI connection, see page 15.

The ColorStream HD1/HD2 and HDMI jacks can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems; however, a 1080i signal will provide the best picture performance.

If your DTV receiver or set-top box is not compatible with component video or HDMI, use the S-video connections (plus the standard audio connections) instead (see page 11).

Introduction

your TV

Connecting

Using the

Remote Control

From Antenna

IN from ANT OUT to TV CH 3

CH 4

From DTV Antenna

Satelite IN

Stereo VCR

S-VIDEO

VIDEO

COMPONENT VIDEO

AUDIO

RPB

OUT

VIDEO

OUT

AUDIO

OUT

LRL

your TV

Setting up

Features

Using the TV’s

Appendix

Index

DTV Receiver with component video

Connecting two VCRs

This connection allows you to record (dub/edit) rom one VCR to another VCR while watching a videotape. You can also record

Introduction

your TV

Connecting

from ont TV channel while watching another TV channel. You will need:

From Antenna

• two coaxial cables

• two sets of standard A/V cables

VCR1

IN from ANT OUT to TV

CH 3 CH 4

VIDEO

AUDIO

OUT

Note:

If you have VCRs with S-video, use S-video cables instead of standard video cables for better picture performance. Do not connect both a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

Do not connect the same VCR to the output and input jacks on the TV at the same time. To dub or edit, VCR 2 must select Line IN, and the TV must select VIDEO 1 (see

“Selecting the antenna input” on page 26).

* The Video OUT jack does not output the

POP picture.

** The Audio OUT jacks can output the sound

of either the Main or POP picture (see “Selecting the Audio OUT sound” on page

59).

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

VCR2

CH 3 CH 4

VIDEO AUDIO

OUT

Connecting a camcorder

This connection allows you to watch video materials recorded on a camcorder.

You will need:

• one set of standard A/V cables

Note:

If you have a camcorder with S-video, use an S-video cable instead of a standard video cable for better picture performance. Do not

both a standard video cable and an

connect S-video cable at the same time, or the picture performance will be unacceptable.

Appendix

Index

Camcorder

VIDEO

AUDIO

OUT

L/MONO

S-VIDEO

VIDEO

AUDIO

Video-3 (front panel)

Connecting an HDMITM or a DVI device to the HDMI input

The HDMI

[1]

input on your TV receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI

[2]

device.

[3]

This input is designed to accept HDCP material in digital form from EIA/CEA-861/861B– compliant

[4]

consumer electronic devices (such as a set-

program

top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with 1080i high-definition video signals, but will also accept and display 480i, 480p, and 720p signals.

Note: This TV is not intended for connection to and should not be used with a personal computer.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector)

For proper operation, it is recommended that you use a short HDMI cable. You should not encounter difficulty if you use an HDMI cable shorter than

16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with this connection, the HDMI terminal on the TV will not receive the HDMI digital audio signal and you will hear analog audio only.

[1]

HDMI = High-Definition Multimedia Interface.

[2]

DVI = Digital Video Interface.

[3]

HDCP = High-bandwidth Digital Content Protection.

[4]

EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

• When turning on your electronic components,

turn on the TV first, and then the HDMI or DVI device.

• When turning off your electronic components,

turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

• one HDMI-to-DVI adapter cable (HDMI type A connector)

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

• one pair of standard analog audio cables

An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below).

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

HDMI device

VIDEO AUDIO

OUT

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

HDMI OUT

DVI device

VIDEO AUDIO

DVI

OUT

Features

Using the TV’s

Appendix

Index

Introduction

Connecting an audio system

This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the TV’s remote control.

To control the audio, turn on the TV and the amplifier, and turn off the TV’s built-in speakers (see “Turning off the built-in speakers” on page 59).

You will need:

• one pair of standard audio cables

Amplifier

LINE IN LR

your TV

Connecting

Note:

To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set above 0 (zero).

For example, if the volume of the TV is set to 0, you will not be able to hear any sound, even the volume of the amplifier is at its highest level.

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

Using the remote control

Preparing the remote control for use

Your Toshiba TV remote control has one dedicated TV mode and five universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The target devices and default devices being programmed for each mode are as follows:

Target device/Mode mapping

Mode Device TV Toshiba TV CABLE/SAT Universal Cable, Satellite VCR Universal VCR, DVD, LD, Cassette DVD Universal DVD, VCR, LD, Cassette AUDIO1 Universal Audio: Amp., Tuner, Misc.Audio, CD/MD AUDIO2 Universal Audio: CD/MD, Amp., Tuner, Misc.Audio

Default device codes

Mode Default device TV Toshiba TV CABLE/SAT Toshiba Satellite receiver VCR Toshiba VCR DVD Toshiba DVD AUDIO1 Pioneer Audio receiver AUDIO2 Pioneer LD

Repeatedly press MODE to cycle among the modes. If you own different brands of audio/video devices, you must first program your remote control (see “Programming the remote control for use with your audio/video devices” on page 20).

Note:

Your TV’s remote control may not operate certain features on your VCR, cable TV converter, or other electronic device.

Refer to the owner’s manuals for your other devices to determine their available features. If your TV’s remote control does not operate a specific feature on a device,use the remote control that came with the device.

TV CABLE/SAT VCR DVD AUDIO1 AUDIO2

MODE

PIC SIZE

ACTION

DVD RTN CH RTN

SLOW/DIR

INPUT

POWER

LIGHT SLEEP

123

456

789

+10

100/

FAV

ENTER

FAV

EXIT

DVD CLEAR

RECALL

SKIP/SEARCH

ENT

VOL

MUTE

MODE

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Installing the remote control batteries

To install the batteries:

1. Slide the battery cover off the back of the remote control.

2. Install two “AA” size alkaline batteries. Match the + and – signs on the batteries to the signs on the battery compartment.

3. Slide the battery cover back on to the remote control until the lock snaps.

Caution:

• Do not throw batteries into a fire.

Note:

• Dispose of batteries in a designated disposal area.

• Attention should be drawn to the environmental aspects of battery disposal.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace both batteries with new ones. Do not mix battery types or combine used batteries with new ones.

• If the batteries are dead or if you will not use the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

Features

Using the TV’s

Appendix

Index

Remote Control functional key chart

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

LIGHT Lights the remote key, and toggles between enabled and disabled Illumination mode. SLEEP Sleep timer --- --- --- --- --- --- --POWER Power Power Power Power Power Power Power Power 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6

MODE Remote control device mode selection

PIC SIZE Selects the TV TV TV TV TV TV TV

7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 ACTION --- --100/– 100 --- 100/- --- +10 --- --- --0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0, 10 Digit 0 ENT (CH Enter) GUIDE/SETUP INFO/TITLE --- --- INFO --- TITLE= --- --- ---

FAVORITE/ Favorites --SUBTITLE

THEATERLINK/ AUDIO

MENU/ Menu --- Action, --- Menu --- --- --ACTION Menu

yz (FAV yz) Menu select --- Menu select --- Menu select --- --- ---

x • Menu select --- Menu select --- Menu select --- --- ---

ENTER Enter --- Select --- Enter --- --- --VOL

EXIT/ Exit --- Exit --- DVD clear --- --- --DVD CLEAR

INPUT TV/Video TV TV VCR input TV --- TV TV

MUTE RECALL On-screen On-screen On-screen On-screen On-screen --- --- ---

CH RTN/ Previous Previous Previous --- DVD --- --- --DVD RTN channel channel channel return

SLOW/ DIR x--- --- --- --- Slow REV --- --- ---

SKIP/ SEARCH x--- --- --- --- Skip REV

REW VCR VCR VCR Rewind Rewind PAUSE/STEP VCR VCR VCR Pause Pause PLAY VCR VCR VCR Play Play FF VCR VCR VCR Fast FWD Fast FWD --- Fast FWD Fast FWD

Key Label

yz Volume Volume Volume Volume Volume Volume Volume Volume

yz Channel Channel Channel Channel --- Channel --- ---

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassette

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)

image shape.

Action, Menu

--- CH Enter --- --- --- --- --- ---

--- --- Guide --- DVD setup --- --- ---

Favorites

--- --- --- --- Audio --- --- ---

FAV yz

up/down* up/down* up/down* up/down* up/down* up/down* up/down* up/down*

up/down up/down up/down up/down up/down

select Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute*

display display display display display

•

--- --- --- Slow FWD Slow FWD --- --- ---

•

--- --- --- --- Skip FWD

--- Menu --- --- ---

Top menu

--- Subtitle --- --- ---

---

Skip FWD Skip REV

Rewind Rewind Pause Pause Play Play

---

Key Label

TV/VCR VCR AM/FM --- --- --- --- Disc shift AM/FM Disc shift Deck side

DISC A/B switch STOP VCR VCR VCR Stop Stop --- Stop Stop REC

POP CH

SPLIT POP Split TV TV TV TV TV TV TV POP DIRECT CH POP Direct ch FREEZE Still picture TV TV TV TV TV TV TV SWAP POP Swap TV TV TV TV TV TV TV CH SCAN POP SOURCE POP Source TV TV TV TV TV TV TV

Notes:

• “---” will send nothing.

• “ TV” will jump to TV.

• “ VCR” will jump to last active VCR or DVD. Active VCR/ DVD is defined as the mode that remains for a minimum of 5 seconds, or if a key is pressed in that mode.

The VOLUME and MUTE will jump to “TV” by default. When the volume is unlocked, all the devices will have their own volume.

The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See “Using the volume lock feature” on page 21.

Press the REC button twice within 5 seconds to record each audio/video source.

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassette

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)

---

VCR VCR VCR Record** --- --- --- Record**

POP channel TV TV TV TV TV TV TV up/down

TV TV TV TV TV TV TV

Ch scan

TV TV TV TV TV TV TV

TV/SAT TV/VCR --- --- --- Reverse

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

Programming the remote control for use with your audio/video devices

Introduction

Device code setup

your TV

Connecting

Using the

Remote Control

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular target unit, you can cycle the remote control through the available codes for that

your TV

Setting up

device mode and sample the functions to find the code that properly operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

Features

Using the TV’s

Appendix

1. Refer to the Device code table on pages 22–23 to find the code for your device.

If more than one number is listed, try each one separately until you find one that works.

2. Press MODE until the Mode indicator for the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3. While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code for your device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4. Point the remote control at the device and press POWER to test the code.

If the device turns on, you have entered the correct code. If the device does not respond to the remote control, you may

have entered the wrong code. Repeat steps 3 and 4 using another code.

5. Press MODE to select the TV mode to control the TV.

1. Press MODE to select the mode you want to set up.

2. While holding down the RECALL button, press 8 –5 –0 –0. The remote control will enter program mode.

3. Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4. If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press y, and then press POWER. Repeat this step until the device responds to the remote control, and then press RECALL.

Note:

• Every time you replace the batteries, you must reprogram the remote control.

• Some newer VCRs are capable of working on either of two remote codes.These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control

TV CABLE/SAT VCR DVD AUDIO1 AUDIO2

MODE

PIC SIZE

ACTION

DVD RTN CH RTN

SLOW/DIR

INPUT

POWER

LIGHT SLEEP

123

456

789

+10

100/

FAV

ENTER

FAV

EXIT

DVD CLEAR

RECALL

SKIP/SEARCH

ENT

VOL

MUTE

POWER

Numbers MODE

RECALL

Index

Note: When a search cycle is completed, the mode indicator will blink

three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

Using the volume lock feature (8000)

For the TV, CABLE/SAT, VCR, and DVD modes, the volume controls (VOL yz and MUTE) can be programmed (locked) to the selected device mode. This feature does not apply to the AUDIO1/2 modes.

For example, to lock the volume controls to always jump to the CABLE/SAT mode:

1. Repeatedly press MODE to select the CABLE/SAT mode.

2. While holding down the RECALL button, press 8 –0 –0 –0.

3. Press VOL y.

The Mode indicator will blink two times (locked).

The following table describes in more detail the Volume Lock implementation.

TV CABLE/SAT VCR DVD AUDIO1 AUDIO2

MODE

PIC SIZE

ACTION MENU

DVD RTN CH RTN

SLOW/DIR

LIGHT SLEEP

123

456

789

+10

100/

FAV

ENTER

FAV

EXIT

DVD CLEAR

INPUT

RECALL

SKIP/SEARCH

POWER

Introduction

Number MODE

ENT

your TV

Connecting

VOL

MUTE

VOL y z

RECALL

Volume Locked to

TV (default)

TV CBL/SAT VCR DVD AUD1 AUD2

TV TV TV TV AUD1 AUD2 CBL/SAT CBL/SAT CBL/SAT CBL/SAT CBL/SAT AUD1 AUD2 VCR VCR VCR VCR VCR AUD1 AUD2 DVD DVD DVD DVD DVD AUD1 AUD2 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2

To reset the volume controls to the original device code:

1. While holding down the RECALL button, press 8 –0 –0 –0.

2. Press VOL z.

The Mode indicator will blink four times (unlocked).

Operational feature reset (8900)

This feature clears all setup features not related to “Device code set up” and resets the Volume Lock to “TV.”

To reset the features:

While holding down the RECALL button, press 8 –9 –0 –0. The Mode indicator will blink two times, and then pause and blink two more times.

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

+ 47 hidden pages