Toshiba 62HMX95, 52HMX95 User Manual

Download

Page 1

WNER’S

ANUAL

Integrated High Definition

™

DLP

For an overview of steps for setting up your new TV, see page 9.

Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider.

Note: If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of DLP TV lamp technology and is NOT a sign of malfunction. For details, see “IMPORTANT NOTICE ABOUT HOT LAMP RESTART” on page 5.

Projection Television

HIGH-DEFINITION TELEVISION

Compatible with Toshiba’s new

Audio/Video Hard Drive Recorder!

See pages 26 and 55 for details.

52HMX95 62HMX95

Owner’s Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model number:

Serial number:

23566726A

Page 2

Dear Customer,

Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV.

Before operating the TV, please read this manual completely, and keep it nearby for future reference.

Safety Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING

RISK OF ELECTRIC SHOCK!

DO NOT OPEN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

unit replacement and care” on pages 129–131 of this manual.)

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Lamp Unit Replacement

CAUTION: HOT SURFACE!

The temperature of the lamp immediately after use exceeds

392°F (200°C). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

The lamp in this product has a limited service life. The length of service life varies depending on product use and user settings. If you use the lamp beyond its service life:

• you may notice a reduction in the colors and/or brightness of the picture, at which time you should replace the lamp unit; and

• the strength of the quartz glass in the lamp will be reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

Dispose of the used lamp unit by the approved method for your area.

See “Lamp unit replacement and care” on pages 129–131.

Note: The lamp unit contains mercury.

Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

(This does not apply to “Lamp

NOTICE OF POSSIBLE TV STAND INSTABILITY

CAUTION: This television is for use only with the Toshiba stand listed below. Use with other

causing possible injury.

carts or stands is capable of resulting in instability

Television Stand Model 52HMX95 ST 5275 62HMX95 ST 6275

NOTE TO CATV INSTALLERS IN THE U.S.A.

This is a reminder to call the CATV system installer’s attention to Article 820-40 of the U.S. NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 27 and 28 on page 4.

Child Safety

It Makes A Difference Where Your TV Stands

Congratulations on your purchase! As you enjoy your new TV, keep these safety tips in mind:

The Issue

 If you are like most consumers, you have a TV in your home. Many homes,

in fact, have more than one TV.

 The home theater entertainment experience is a growing trend, and larger

TVs are popular purchases; however, they are not always supported on the proper TV stands.

 Sometimes TVs are improperly secured or inappropriately

situated on dressers, bookcases, shelves, desks, audio speakers,

chests, or carts. As a result, TVs may fall over, causing

unnecessary injury.

Toshiba Cares!

 The consumer electronics industry is committed to making home entertainment enjoyable and safe.

 The Consumer Electronics Association formed the

Home Entertainment Support Safety Committee, comprised

of TV and consumer electronics furniture manufacturers, to

advocate children’s safety and educate consumers and their

families about television safety.

Tune Into Safety

 One size does NOT fit all! Use appropriate furniture large enough to

support the weight of your TV (and other electronic components).

 Use appropriate angle braces, straps, and anchors to secure your furniture

to the wall (but never screw anything directly into the TV).

 Carefully read and understand the other enclosed instructions for proper

use of this product.

 Do not allow children to climb on or play with furniture and TVs.  Avoid placing any item on top of your TV (such as a VCR, remote control,

or toy) that a curious child may reach for.

 Remember that children can become excited while watching a program

and can potentially push or pull a TV over.

 Share our safety message about this hidden hazard of

your family and friends. Thank you!

2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org

CEA is the Sponsor, Producer and Manager of the International CES

the home with

Page 3

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

Wide blade

16) WARNING: This product contains a lamp to project

the picture, and requires special safety precautions:

• See pages 129–131 for instructions on lamp unit replacement and care.

• DO NOT attempt to service this product except as specified on pages 129–131. The only user-

serviceable item in this product is the lamp unit.

Installation, Care, and Service

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

17) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

18) DANGER: RISK OF SERIOUS PERSONAL

INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on

an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

19) Never place or store the TV in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C).

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14a) Item 14 does not apply to “Lamp unit replacement and

care” on pages 129-131 of this manual.

14b) CAUTION: If the TV is dropped and the cabinet or

enclosure surface has been damaged or the TV does not operate normally, take the following precautions:

• ALWAYS turn off the TV and unplug the power cord to

avoid possible electric shock or fire.

• To prevent personal injury, never handle the damaged

television.

• ALWAYS contact a service technician to inspect the TV

any time it has been damaged or dropped.

15) CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

20) Always place the TV on the applicable optional TV stand(s) listed in the “Specifications” section (if available for this TV model) or on a sturdy, level, stable surface that can safely support the size and weight of the unit. See “Notice of possible TV stand instability” and “Child Safety” on page 2.

21) Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled with liquid, or candles on top of the TV.

22) Always place the back of the television at least one (1) inch away from any vertical surface (such as a wall) to allow proper ventilation.

23) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar surface;

• too close to drapes, curtains, or walls; or

• in a confined space such as a bookcase, built-in cabinet,

or any other place with poor ventilation.

The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV.

24) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

25) Never overload wall outlets and extension cords.

26) Always operate this equipment from a 120 VAC, 60 Hz power source only.

(continued on next page)

Page 4

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Power service grounding

Ground clamps

Antenna lead-in wire

Electric service equipment

electrode system (NEC Art 250 Part H)

Installation

(continued from previous page)

Care

(continued from previous column)

27) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

28) DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH!

• Use extreme care to make sure you are never in

a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

33) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

) During normal use, the TV may make occasional snapping

or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

35) Special care for DLP™ (Digital Light Processing) units: The lamp unit in this product has a limited service life. The

length of service life varies depending on product use or user settings. If you use the lamp beyond its service life:

you may notice a reduction in the colors and/or

•

brightness of the picture, at which time you should replace the lamp unit; and

the strength of the quartz glass in the lamp will be

•

reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

See “Lamp unit replacement and care” on pages 129–131.

• Dispose of the used lamp unit by the approved method for

your area.

• The lamp unit contains mercury. Disposal of

mercury may be regulated due to environmental

information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

considerations. For disposal or recycling

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

29) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen. Turn the TV off to check for reflections on the screen, and then remove the source of reflections while viewing the TV.

30) Always unplug the TV before cleaning. Never use liquid or aerosol cleaners. Clean only with a soft, dry cloth. Do not spray volatile compounds, such as insecticide, on the cabinet. This may discolor or damage the cabinet.

31) WARNING: RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV cabinet slots.

32) If the air temperature rises suddenly (for example, when the TV is first delivered), condensation may form on the lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the TV for 6 to 7 hours to allow the condensation to evaporate.

Service

) WARNING: RISK OF ELECTRIC SHOCK!

Never attempt to service the TV yourself,

except as specified on pages 129–131. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Center.

37) If you have the TV serviced:

• Ask the service technician to use only replacement parts

specified by the manufacturer.

• Upon completion of service, ask the service technician to

perform routine safety checks to determine that the TV is in safe operating condition.

38) When the TV reaches the end of its useful life, ask a qualified service technician to properly dispose of the TV.

Note: The lamp unit contains mercury. Disposal of mercury may be regulated due to environmental considerations. Dispose of the used lamp unit by the approved method for your area. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

Digital Light Processing, DLP and the DLP medallion are trademarks of Texas Instruments.

Page 5

FCC Declaration of Conformity Compliance Statement (Part 15):

The Toshiba 52HMX95 and 62HMX95 DLP™ projection TVs comply with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.

The party responsible for compliance to these rules is: Toshiba America Consumer Products, L.L.C. 82 Totowa Rd. Wayne, NJ 07470. Ph: (973) 628-8000

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment.

Important notes about your DLPTM projection TV

1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black or the lamp may fail, at which time you must replace the lamp unit. See “Lamp unit replacement and care” on pages 129–131.

2) When the lamp mode is set to Low Power, every time the TV is powered on, the lamp will initially be in High Bright mode but will switch to Low Power mode in approximately 1 minute. You will notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction. (See page 80 for details.)

3) Every time the TV is powered on, it may take several minutes for the picture to obtain full brightness.

4) The TV’s display is manufactured using an extremely high level of precision technology; however, an occasional pixel (dot of light) may show constantly on the screen. This is a structural property of DLP™ (Digital Light Processing™) technology and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance (see item 5, below).

5) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture quality may be affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer from eye fatigue. See item 29 on page 4.

6) Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a “rainbow effect” on the screen, which can, in rare instances, result in eye fatigue. This is a rare occurrence related to DLP technology and is not a sign of TV malfunction.

7) The TV contains several cooling fans to moderate the

internal temperature. You may be able to hear the fans

for several minutes after the TV is powered off. This is a normal function of the Quick Restart™ feature and is not a sign of TV malfunction. You can set the Quick Restart™ feature to stop the fans as soon as the TV is powered off. See “Setting the Quick Restart™ feature” on page 56.

8) The green and red LED lights on the TV’s front control touchpad indicate the TV’s current status. If either light flashes, see “LED indications” on page 125 for details.

9) Every time the TV power cord is plugged in, either the message “Now Booting...” will display on-screen until the picture appears, or the green LED will blink until the TV enters standby mode (plugged in but not powered on). This is normal and is not a sign of malfunction.

10) When connecting an external A/V device, if you connect the

device’s video output to the TV and the device’s audio output to a separate audio system, the picture and sound may not synchronize completely.

11) When playing a video game on the TV, there may be a slight

delay between your command (e.g., joystick, keyboard) and the picture movement on the screen.

IMPORTANT NOTICE ABOUT “HOT LAMP RESTART”

When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen in the following situations:

• when the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes; or

• if the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes.

This is a property of DLP TV lamp technology and is NOT a sign of malfunction.

If this occurs, the green LED on the TV front panel will blink (and the red LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If both LEDs are blinking, you will need to turn the TV off and then on again to restart the lamp.

Page 6

Contents

Important safety, care, and service information ........... 2–4

FCC Declaration of Conformity Compliance

Statement (Part 15): ............................................................ 5

Important notes about your DLP™ projection TV ............... 5

Chapter 1: Introduction .......................................................... 8

Welcome to Toshiba ........................................................... 8

Features of your new TV .................................................... 8

Overview of steps for installing, setting up, and

using your new TV .......................................................... 9

Chapter 2: Connecting your TV ......................................... 10

TV front panel touchpad and side panel controls

and connections ........................................................... 10

TV back panel connections ................................................ 11

Overview of cable types ...................................................... 13

About the connection illustrations ...................................... 14

Connecting a digital CableCARD

™

.................................... 14

Connecting a VCR and antenna or Cable TV

(no Cable box) ............................................................... 15

Connecting a camcorder ..................................................... 15

Connecting a VCR and Cable box ..................................... 16

Connecting a VCR and satellite receiver ............................. 17

Connecting a DVD player with S-video, a VCR,

and a Cable box .............................................................. 18

Connecting a DVD player with ColorStream

(component video) and a VCR ....................................... 19

Connecting two VCRs ....................................................... 20

Connecting an HDMI

™

or DVI device to the

HDMI input .................................................................. 21

Connecting a device to the TheaterNet OUT infrared

terminal using the IR blaster cable for IR pass-through

device control ................................................................. 22

Connecting an IR receiver/repeater or home theater

control system to the TheaterNet IN infrared terminal ... 23

Connecting a digital audio system ...................................... 24

Connecting an analog audio system .................................... 24

Connecting IEEE1394 video devices .................................. 25

Using analog-compatible IEEE1394 devices ................... 25

Supported signals ........................................................... 25

Using TheaterNet

™

on-screen device control .................. 25

Connecting an AVHD

(external hard drive) or D-VHS recorder .................... 26

IEEE1394 device initialization ....................................... 26

IEEE1394 device management ....................................... 27

G-LINK

connection ......................................................... 28

Connecting a personal computer (PC) ............................... 29

Connecting a home network .............................................. 30

Chapter 3: Using the remote control ................................. 31

Learning about the remote control ..................................... 31

Installing the remote control batteries................................. 33

Using the remote control MODE button to control

your other devices........................................................... 33

Remote Control functional key chart ................................. 34

Programming the remote control to operate

your other devices........................................................... 36

Multi-brand remote control device codes............................ 38

Chapter 4: Menu layout and navigation ........................... 40

Main menu layout .............................................................. 40

Setup/Installation menu layout........................................... 41

Navigating the menu system............................................... 41

Chapter 5: TV Guide On Screen

Setting up the TV Guide On Screen TV Guide On Screen

Turning off the TV Guide On Screen

setup ............................ 42

system ..................... 42

Reminder ....................................... 45

automatic display feature ................................................ 45

Chapter 6: Setting up your TV ............................................. 46

Selecting the menu language............................................... 46

Configuring the antenna input sources for the ANT 1

and ANT 2 terminals ..................................................... 46

Programming channels into the TV’s channel memory ....... 47

Programming channels automatically .......................... 47

Manually adding and deleting channels in the

channel memory ..................................................... 48

Programming your favorite channels .................................. 49

Setting up and using TheaterNet

™

on-screen

device control ................................................................. 50

Setting up TheaterNet ................................................. 50

Using the TheaterNet control icons............................. 51

TheaterNet IR device codes ........................................ 52

Setting the AVHD device skip time .................................... 55

Setting the HDMI

™

audio mode ........................................ 55

Setting the time and date .................................................... 55

Viewing the CableCARD Setting the Quick Restart

™

menu ...................................... 56

™

feature ..................................... 56

Viewing the digital signal meter ......................................... 57

Viewing the system status ................................................... 57

Chapter 7: Using the TV Guide On Screen

interactive program guide ............................................... 58

Setting up the TV Guide On Screen Navigating the TV Guide On Screen

TV Guide On Screen

remote control functions ......... 59

system ..................... 58

system..................... 59

Video Window ........................................................... 60

Panel Menus ............................................................... 60

Info Box ...................................................................... 61

TV Guide On Screen

Icons ....................................... 61

Services .......................................... 62

LISTINGS screen ....................................................... 62

SEARCH screen.......................................................... 63

RECORDINGS screen ............................................... 65

SCHEDULE screen .................................................... 66

Recording features....................................................... 66

Reminder features ....................................................... 68

SETUP screen ............................................................. 70

Change system settings .......................................... 70

Change channel display ......................................... 70

Change default options .......................................... 71

Page 7

Contents

Chapter 8: Using the TV’s features .....................................72

Selecting the video input source to view ............................. 72

Labeling the video input sources ......................................... 73

Tuning channels ................................................................. 74

Using the Channel Browser

™

...................................... 74

Tuning your favorite channels ..................................... 76

Tuning to the next programmed channel .................... 76

Tuning to a specific channel (programmed or

unprogrammed) ...................................................... 76

Switching between two channels using

Channel Return ...................................................... 76

Switching between two channels using SurfLock

Selecting the picture size ..................................................... 77

Scrolling the TheaterWide

™

............................................................... 76

picture

(TheaterWide 2 and 3 only) ........................................... 79

Using the auto aspect ratio feature ...................................... 79

Selecting the cinema mode (480i signals only) .................... 80

Selecting the lamp mode .................................................... 80

Using the POP features ...................................................... 81

Using the POP double-window feature ....................... 81

Switching the speaker audio (main or POP) ................ 82

POP double-window aspect ratio ................................ 82

Using the FREEZE feature ................................................. 83

Using the favorite channel scan feature ............................... 83

Adjusting the picture .......................................................... 84

Selecting the picture mode .......................................... 84

Adjusting the picture quality ....................................... 84

Using the Color Management feature ......................... 85

Using CableClear

/DNR (digital noise reduction) ...... 86

Selecting the color temperature ................................... 86

Using MPEG noise reduction ..................................... 87

Using dynamic contrast............................................... 87

Using the closed caption mode ........................................... 88

Advanced closed captions ............................................ 88

Digital closed captions ................................................ 89

Adjusting the audio ............................................................ 90

Muting the sound ....................................................... 90

Using the digital audio selector ................................... 90

Selecting stereo/SAP broadcasts................................... 90

Adjusting the audio quality ......................................... 91

Using the sub-bass system (SBS) ................................. 91

Using the StableSound Using the SRS WOW

feature ................................... 91

™

surround sound feature .......... 92

Using the virtual surround sound feature (Dolby

Virtual/TruSurround) ............................................. 92

Turning off the built-in speakers ................................. 93

Selecting the optical audio output format ................... 93

Setting the On/Off Timer .................................................. 94

Setting the sleep timer ........................................................ 94

Using the PC settings feature.............................................. 95

Displaying TV setting information on-screen

using RECALL ............................................................... 96

Understanding the auto power off feature........................... 96

Understanding the last mode memory feature .................... 96

Using the Gray Level feature .............................................. 96

Chapter 9: Using the Locks menu ....................................... 97

Entering the PIN code ....................................................... 97

If you cannot remember your PIN code ............................. 97

Changing your PIN code ................................................... 97

Blocking TV programs and movies by rating (V-Chip) ......... 98

Blocking channels............................................................... 99

Unlocking programs temporarily ........................................ 99

Using the input lock feature ............................................... 99

Using the GameTimer

™

................................................... 100

Using the front panel lock feature..................................... 100

Chapter 10: Using the Picture Viewer and

Audio Player .......................................................................... 101

Media specifications ......................................................... 101

File/folder name specifications .................................. 101

Picture Viewer/JPEG file specifications ..................... 101

Audio Player/MP3 file specifications ......................... 102

Networked PC specifications .................................... 102

Memory card specifications ....................................... 102

Using the Picture Viewer .................................................. 103

Accessing JPEG files stored on a networked PC ........ 103

Accessing JPEG files stored on a memory card .......... 103

Viewing JPEG files on the TV .................................. 104

Using the Audio Player..................................................... 105

Accessing MP3 files stored on a networked PC ......... 105

Accessing MP3 files stored on a memory card ........... 105

Playing MP3 audio files on the TV ........................... 106

Memory card care and handling ....................................... 106

Chapter 11: Using the THINC™ home network feature ....

107

A. Connect the TV to your home network ....................... 107

B. Set up the network address ........................................... 107

Automatically setting up the network address............ 107

Manually setting up the network address .................. 108

Resetting the network address ................................... 109

C. Set up file sharing on your PC ..................................... 110

Compatible operating systems ................................... 110

Setting up file sharing on a PC with Microsoft

Windows® XP Service Pack 1 or Service Pack 2 ..... 110

Setting up file sharing on a PC with Microsoft

Windows® 2000 .................................................... 111

D. Set up file sharing on the TV....................................... 112

E. Viewing/playing shared files on the TV ........................ 112

F. Set up e-mail scheduling ............................................... 113

Required information and services ............................ 113

Setting up e-mail scheduling ..................................... 113

Description of fields in the “E-mail Scheduling

Setup” window .............................................. 115–116

G. Using e-mail scheduling .............................................. 117

E-mail parameters ..................................................... 117

Sending a request e-mail to the TV ........................... 117

Formatting a request e-mail....................................... 117

Receiving an e-mail from the TV .............................. 119

Modifying an existing recording or reminder ............ 119

Chapter 12: Troubleshooting ............................................. 120

General troubleshooting ........................................... 120–124

LED indications ............................................................... 125

TV Guide On Screen

FAQ ..................................... 126–128

Chapter 13: Appendix ......................................................... 129

Lamp unit replacement ............................................ 129–131

Specifications ................................................................... 132

Limited United States Warranty ....................................... 133

Index ....................................................................................... 135

Page 8

Introduction

Welcome to Toshiba

Thank you for purchasing this Toshiba TV, one of the most innovative DLP™ projection TVs on the market. The goal of this manual is to guide you through setting up and operating your TV as quickly as possible.

See “Important notes about your

™

DLP

projection TV” on page 5.

• This manual applies to models 52HMX95 and 62HMX95. Before you start reading, check the model number on the back of your TV.

• Instructions in this manual are based on using the remote control. You also can use the controls on the TV front touchpad if they have the same name as those referred to on the remote control. (MENU on the front touchpad functions as ENTER when a menu is on-screen or when the TV Guide On Screen

system is open.)

• The side panel and back panel provide terminals for connecting other equipment to your TV. See page 10 for front touchpad and side panel details. See page 11 for back panel details. See pages 14–30 for instructions on connecting other devices to your TV.

• Please read all safety and operating instructions in this manual carefully and keep this manual for future reference.

Features of your new TV

The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, DLP™ projection TV:

•

Integrated digital tuning (8VSB ATSC and QAM)

•

TV Guide On Screen

•

Digital CableCARD™ slot

•

Digital recording

no-fee interactive program guide (Chapters 5 and 7).

for viewing encrypted digital Cable TV programs (page 14).

by connecting a Toshiba Symbio™ Audio/Video Hard Drive Recorder or a D-VHS digital recording device

to one of the IEEE1394 jacks. You can record high definition and standard definition material from either tuner (page 26).

Memory card slots

•

[SD Memory Card, MultiMediaCard, Memory Stick, CompactFlash, xD-Picture Card™]

for viewing JPEG picture files as a “slide show” (page 103) and playing MP3 audio files (page 104).

•

TheaterNet™

•

Two IEEE1394 ports

•

Two HDMI (DVI)

•

Two sets of ColorStream® HD

•

Dolby Digital

icons for on-screen control of external IR and

for multi-device connection and control (page 25).

digital, high-definition multimedia interfaces (page 21).

high-resolution component video inputs (pages 17 and 19).

(page 24),

SRS WOW™

(page 92), and Dolby Virtual TruSurround (page 92),

audio technologies.

Digital Audio Out

•

CableClear® DNR

• Double-window

•

PC IN (Analog RGB)

•

RJ-45 (Ethernet) port

optical audio connection (page 24).

digital picture noise reduction (page 86).

POP

(page 81) and multi-window

terminal for using the TV screen as the display for a PC (pages 11 and 29).

for connecting to a home network to allow file sharing (JPEG picture files and MP3 audio fiiles)

and e-mail scheduling of recordings and reminders (page 30).

eliminates the need for a separate digital converter set-top box (in most cases).

Favorites

IEEE1394

(page 83) features.

devices (page 50).

Note: After you set up the TV Guide

On Screen

automatically by default when you turn on the TV. You can turn off the automatic program guide (page

45) and instead press the TV GUIDE button on the remote control to

manually open the program guide.

system (Chapter 5),

the program guide opens

______________ In the United States, TV Guide and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.

GEMSTAR-TV GUIDE INTERNATIONAL INC. AND/OR ITS RE LATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE ACCU RACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SERVICE AVAILABILITY IN YOUR AREA. IN NO EVENT SHALL GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES BE LIABLE FOR ANY DAMAGES IN CONNECTION WITH THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN® SYSTEM.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

SYSTEM AND CANNOT GUARANTEE

Page 9

Chapter 1: Introduction

Overview of steps for installing, setting up, and using your new TV

Follow these steps to set up your TV and begin using its many exciting features.

1. Carefully read the important safety, installation, care, and service information on pages 2–5. Keep this manual for future reference.

2. Observe the following when choosing a location for the TV:

• Read “Installation” on pages 3–4.

• Read “Important notes about your DLP™ projection TV” on

page 5.

•

Place the TV on the applicable optional TV stand listed in the “Specifications” section (if available for this TV model) or on a sturdy, level, stable surface that can safely support the size and weight of the unit.

NOTICE OF POSSIBLE TV STAND IN STABILITY

DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH! Use this TV only with the TOSHIBA TV

stand listed in the “Specifications” section of this manual. Use with other stands may result in instability, causing possible injury or death.

• Place the TV in a location where light does not reflect on the

screen.

• Place the TV far enough from walls and other objects to

allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF

DAMAGE IS NOT COVERED UNDER THE TOSHIBA WAR RANT Y.

3. Do not plug in any power cords until AFTER you have connected all cables and devices to your TV.

4. BEFORE connecting cables or devices to the TV, learn the functions of the TV’s connections and controls (pages 10-

12).

5. Connect your other electronic device(s) to the TV (pages 14–30).

6. Connect the G-LINK blaster cables) from your VCR and/or Cable box (if applicable) to the G-LINK

terminal so you can use the TV Guide On Screen

features (applies to VCRs and cable boxes only). See page 28.

7. Install the batteries in the remote control (page 33).

8. See “Learning about the remote control” (page 31) for

an overview of the buttons on the remote control.

cable (either one of the enclosed IR

9. Program the remote control to operate your other device(s) (pages 33–39).

10. AFTER connecting all cables and devices, plug in the power cords for your TV and other devices.

11. After you plug in the TV power cord, the green LED (on the TV front touchpad, to the left of the POWER button) will blink while the TV is booting until the remote control is usable. When the green LED stops blinking, press POWER to turn on the TV.

See “LED indications” on page 125.

12. See “Menu layout and navigation” for a quick overview of navigating the TV’s menu system (pages 40–41).

13. See Chapter 5 for details on setting up the TV Guide On Screen

system (if available in your area).

14. See Chapter 7 for details on using the TV Guide On Screen® program guide (if available in your area).

15. Program channels into the TV’s channel memory (page 47).

16. Set up the TheaterNet™ on-screen device control feature (if applicable to your particular home theater system components) (page 50).

17. For details on using the TV’s features, see Chapters 8

and 9.

18. For details on using the JPEG Picture Viewer and MP3 Audio Player to view/play files saved on either a memory card or networked PC, see Chapter 10.

19. For details on connecting the TV to a home network to allow file sharing and e-mail scheduling of recordings and reminders, see Chapter 11.

20. For help, refer to the Troubleshooting Guide (Chapter 12).

21. For lamp unit replacement instructions, see Chapter 13.

22. For technical specifications and warranty information, see Chapter 13.

23. Enjoy your new TV!

Page 10

Connecting your TV

TV front panel touchpad and side panel controls and connections

Front of TV

MENUVOLUMECHANNELEXITTV/VIDEO POWER

Remote sensor

Front panel touchpad*

EXIT

TV/VIDEO

Channel

GUIDE

*Gently touch the printed keys on the touchpad. **The MENU button on the TV front panel touchpad functions as the

ENTER button when a menu is on-screen.

zyx •

zy7Volume

MENU (ENTER)**

x •

Green/Red LEDs

POWER

Right side of TV

Side panel

{

VIDEO-3 IN

Memory card

{

slots

!¡

Remote sensor

control toward this area of the TV screen. See “Remote control effective range” on page 32.

GUIDE

— Press to access the TV Guide On Screen

interactive program guide. (See Chapters 5 and 7.)

EXIT

— When a menu is on-screen, this button functions as the EXIT button. Press to instantly close an on-screen menu.

TV/VIDEO

functions as the TV/VIDEO button (page 72). Repeatedly press to change the input source you are viewing (ANT 1, ANT 2, VIDEO 1, VIDEO 2, VIDEO 3, HDMI 1, HDMI 2, ColorStream HD1, ColorStream HD2, PC).

ARROWS

buttons function as up/down/left/right menu navigation buttons.

MENU (ENTER)

pages 40–41). When a menu is on-screen or the TV Guide On Screen the front touchpad functions as the ENTER button.

POWER

If the TV stops responding to the controls on the remote control or TV front panel and you cannot turn off the TV, press and hold the POWER button on the TV front panel for 5 or more seconds to reset the TV.

(behind the screen) — Point the remote

— When no menu is on-screen, this button

yzx • — When a menu is on-screen, these

— Press to access the menu system (see

program guide is open, the MENU button on

— Press to turn the TV on and off.

CHANNEL

buttons change the channel (programmed channels only; see page 47). When a menu is on-screen, these buttons function

as up/down menu navigation buttons.

VOLUME

buttons adjust the volume level. When a menu is on-screen, these buttons function as left/right menu navigation buttons.

Green and Red LEDs

When the red LED lights solid (not blinking), it indicates

that the TV power cord is plugged in.

When the green LED lights solid (not blinking), it indicates that recording is in progress.

See “LED indications” on page 125 for additional information.

VIDEO-3

as “VIDEO 3” and include standard A/V connections plus optional S-video. (The VIDEO 1 and VIDEO 2 A/V connections are on the TV’s back panel; see page 11.)

Memory card slots

!¡

the memory card slots to view JPEG files (such as photos) as a “slide show” on your TV or listen to MP3 audio files (see Chapter 10).

yz — When no menu is on-screen, these

x • — When no menu is on-screen, these

— The side panel A/V connections are referred to

— Insert a memory card into one of

Page 11

Chapter 2: Connecting your TV

TV back panel connections

For an explanation of cable types, see page 13.

1 VIDEO 1 IN and VIDEO 2 IN — Two sets of standard

(composite) video and standard audio inputs plus optional S-video inputs for connecting devices with composite video or S-video output.

Note: Standard (composite) video and S-video cables carry only video information; separate audio cables are required for a complete connection.

2 ColorStream® HD-1 and ColorStream® HD-2 — Two sets

of ColorStream (with standard stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream

Note: Component video cables carry only video information; separate audio cables are required for a complete connection.

Variable Audio OUT — Standard analog audio outputs for connecting an analog amplifier with external speakers. See page 24.

4 A/V OUT — Standard composite video and analog audio

outputs for connecting a VCR for editing and dubbing. See page 20 for details.

5 HDMI Audio IN 1 and 2 — Two sets of analog audio IN

terminals for use when connecting a DVI device with analog audio output to one of the HDMI inputs. See page 21. Also see item 2 on the next page.

high-definition component video inputs

. See pages 17 and 19.

12345076

}

6 PC IN/AUDIO — For connecting audio from a personal

7 PC IN/VIDEO— For connecting video from a personal

9 Digital Audio OUT — Optical audio output in Dolby

0 CableCARD

}

computer when using the TV screen as the display for the connected PC. See page 29.

TheaterNet™ (IR) OUT 1 and OUT 2 — For controlling infrared remote-controlled devices through the TV. You can connect up to two devices with either one of the enclosed IR blaster cables, and then control the devices using the TV’s IR pass-through or TheaterNet control features. See pages 22 and 50.

TheaterNet™ (IR) IN

remote-controlled receiver/repeater or home theater control system. See page 23.

Digital or PCM (pulse-code modulation) format for connecting an external Dolby Digital decoder, amplifier, A/V receiver, or home theater system with optical audio input. See page 24.

™

and digital cable TV service (provided by your local cable operator) to view encrypted digital programming. See pages 14 and 56.

— For connecting an infrared

slot — For use with a digital security card

™

on-screen device

___________

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

CableCARD is a trademark of Cable Television Laboratories, Inc.

(Continued on next page)

Page 12

Chapter 2: Connecting your TV

TV back panel connections (continued)

{

12354

1 ANT-1 (cable) IN and ANT-2 IN — Two RF inputs that

support analog (NTSC) and digital (ATSC) off-air antenna signals and analog and digital Cable TV (QAM) signals.

Note: If you have an antenna only, connect it to ANT-1. If you have both cable TV and an antenna, connect the cable TV to ANT-1 and the antenna to ANT-2.

2 HDMI™ IN 1 and 2 — Two High-Definition Multimedia

Interface inputs receive digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. See page 21. Also see item 5 on the previous page.

3 G-LINK

G-LINK

— For use with one of the enclosed IR blaster/

cables to enable the TV Guide On Screen

recording features. See page 28.

4 TheaterNet IEEE1394 1 and 2 — Two bi-directional

digital IEEE1394 ports for connecting multiple devices with compressed digital video. Because these ports are bi-directional, they can be used for playback and recording. You can control your IEEE1394 devices using the TV’s TheaterNet on-screen device control icons. See pages 25–27 and 50.

Note: IEEE1394 cable carries both audio and video information; therefore, separate audio cables are not required.

5 RJ-45 (Ethernet)* — For connecting the TV to a home

network. See page 30.

*THINC™ system

(Toshiba Home Interactive Network Connection)

The RJ-45 (Ethernet) port allows your Toshiba Cinema Series TV to connect to your home network. This revolutionary home entertainment networking system lets you access MP3 audio files and JPEG picture files stored on a networked PC (as shared files) and play/display them on your TV.

You also can play your shared MP3 audio files through a connected audio system.

See pages 24 and 30 and Chapters 10 and 11 for details.

Page 13

Chapter 2: Connecting your TV

Overview of cable types

Note: Two dual-wand IR blaster/G-LINK® cables are included with your TV. All other required cables, if not provided with your other devices, can be purchased at many electronics accessory suppliers.

●

Coaxial (F-type) cable is used for connecting your antenna, cable TV service, and/or cable converter box to the ANT-1 and/or ANT-2 RF inputs on your TV.

●

Standard A/V cables (composite video) usually come in sets of three, and are for use with video devices with analog audio and composite video output. These cables (and the related inputs on your TV) are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio.

●

S-video cable is for use with video devices with S-video output. Separate audio cables are required for a complete connection.

Note: An S-video cable provides better picture performance than a composite video cable. If you connect an S-video cable, be sure to disconnect the standard (composite) video cable or the picture performance will be unacceptable.

●

Component video cables come in sets of three and are for use with video devices with component video output. (ColorStream These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection.

Note: Component video cables provide better picture performance than a standard (composite) video or S-video cable.

●

HDMI cable is for use with devices with HDMI (High-Definition Multimedia Interface) output. HDMI cable delivers digital audio and video in its native format. This cable carries both video and audio information; therefore, separate audio cables are not required for a complete HDMI device connection. See page 21 for further details.

Note: HDMI cable provides better picture performance than a standard (composite) video or S-video cable.

●

IEEE1394 cable is for use with video devices with compressed digital video output that meet CEA specifications for IEEE1394. This cable carries both video and audio information; therefore, no separate audio cables are required for a complete connection. See pages 25–27.

Note:

• The transmission capability of any IEEE1394 cable used with this TV must be S400 (400 Mbps maximum).

• IEEE1394 cable provides better picture performance than a standard (composite) video or S-video cable.

●

Dual-wand IR blaster/G-LINK® cable is for use with video devices with IR (infrared) remote control. Two of these cables are included with your TV. One is for connection to the G-LINK (Chapters 5 and 7). The other can be used with the TV’s IR pass-through feature (page

22) and TheaterNet

Note: The two IR blaster/G-LINK® cables included with your TV have specific characteristics that allow them to work properly with this TV’s IR OUT and G-LINK

aftermarket IR blaster or G-LINK

properly and can cause damage. THIS TYPE OF DAMAGE IS NOT COVERED BY YOUR TOSHIBA WARRANTY.

●

Optical audio cable is for connecting receivers with Dolby Digital or PCM

terminal (page 28) to enable TV Guide On Screen® recording features

™

on-screen device control feature (page 50).

(pulse-code modulation) optical audio input to the TV’s DIGITAL AUDIO OUT terminal. See page 24.

●

Ethernet (RJ-45) cable is used to connect the TV to your home network. See page 30 and Chapter 11.

is Toshiba’s brand of component video.)

cables with this TV. Other cables may not function

terminals. Never use other

Coaxial (F-type) cable

Standard A/V cables (red/white/yellow)

S-video cable

Component video cables (red/green/blue)

HDMI cable

IEEE1394 cable (4-pin)

Dual-wand IR blaster/G-LINK® cable (2 included)

Optical audio cable

Ethernet (RJ-45) cable

Note: Although your TV includes both HDMI and IEEE1394 connections, it may not operate with another device you have that includes such a connection. For example, the IEEE1394 ports are not intended to operate with current model Mini DV camcorders, and the HDMI input is not intended for connection to a computer. Copyright protection requirements may also prohibit or limit connectivity. See page 21 for details about the HDMI input. See pages 25–27 for details about the IEEE1394 ports.

Page 14

Chapter 2: Connecting your TV

About the connection illustrations

You can connect different types and brands of devices to your TV in several different configurations. The connection illustrations in this manual are representative of typical device connections only. The input/output terminals on your devices may differ from those illustrated herein. For details on connecting and using your specific devices, refer to each device’s owner’s manual.

Connecting a digital CableCARD™

This digital television is capable of receiving analog basic, digital basic, and digital premium cable television programming by direct connection to a cable system providing such programming.

™

A security card (such as a digital CableCARD

), provided by your cable operator, is required to view encrypted digital programming.

Certain advanced and interactive digital cable services (such as video-on-demand, a cable operator’s enhanced program guide, and data-enhanced television services) will not work with the use of a CableCARD

™

and may require the use of a separate

set-top box from your cable operator. For more information, contact your local cable operator.

You will need:

 one digital CableCARD

™

(contact your cable operator)

 digital cable subscription service (contact your cable

operator)

TV back panel

From digital Cable service

Note: Connect the digital cable directly to ANT 1 only. If you connect the cable through a VCR first and/or to ANT 2, the TV may not receive the signals correctly.

________

CableCARD is a trademark of Cable Television Laboratories, Inc.

To view encrypted digital channels:



1. Connect your digital Cable TV cable to ANT-1.

™

2. With the front of the CableCARD the CableCARD

™

slot on the back of the TV (see

facing up, insert it into

illustration below left).

™

3. After the CableCARD appears in the Applications menu, with informational screens provided by your digital CableCARD

is inserted, a CableCARD™ option

™

service. See

page 56 for additional information.

CableCard Connected -- Acquiring channel information.

CableCard services will only operate with cable signal connected to Antenna 1.

Note:

• Connect the cable from your digital cable TV service

directly to ANT 1 only. If you connect the digital cable through

a VCR first and/or to ANT 2, the TV may not receive the signals correctly.

• Always use the EJECT button to remove the

CableCARD™. Removing the CableCARD™ without pressing

EJECT can damage the CableCARD and/or TV. Such damage is NOT covered under your Toshiba warranty.

• Never insert any object or card other than a CableCARD™

(including, without limitation, a PCMCIA card) into the CableCARD™ slot.

• Always make sure the CableCARD™ is facing the correct direction.

• When using a CableCARD™, you do not need to program

channels into the TV memory. The CableCARD™ automatically loads the cable channel list into the TV’s channel memory (page 47).

• The CableCARD™ may take up to 5 minutes to “pair” with the TV

and download channel information. CableCARD™ information and channels will not be available until this process is completed.

CableCARD™ technology, like all new and emerging technology, may from time to time experience compatibility issues due to the different ways in which television manufacturers and cable system operators implement the CableCARD™ specifications. Most issues can be easily resolved. If you experience any performance-related CableCARD™ issues with your Toshiba television, please contact Toshiba Consumer Solutions by calling (800) 631-3811 or by visiting

http://www.tacp.com/customersupport/contact.asp.

Applications

TV Guide On Screen

Audio Player

Picture Viewer

Digital CC/Audio Selector

CableCARD

Navigate

IP Service

Conditional Access

CableCARD(tm) Status

Network Setup

CableCARD(tm) Pairing

Back Exit

CH RTN

Select

EXIT

Page 15

Chapter 2: Connecting your TV

Connecting a VCR and antenna or Cable TV (no Cable box)

You will need:

 one signal splitter  three coaxial cables  two sets of standard A/V cables

• For better picture performance, if your VCR has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect both types of video cables to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio OUT terminal using the white audio cable only.

To view the antenna or Cable signal:



Select the ANT 1 video input source on the TV.*

To view the VCR:



Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

To use the TV Guide On Screen® recording features:



1. Connect the G-LINK

cable according to the instructions

on page 28.

2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen

5. See Chapter 7 for details on using the TV Guide On Screen

system.

From Cable TV or antenna

Signal splitter

OUT

Stereo VCR

VIDEO AUDIO

IN from ANT

OUT to TV

CH 3 CH 4

OUT

Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the applicable input mode is selected.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Connecting a camcorder

You will need:

 one set of standard A/V cables

• For better picture performance, if your camcorder has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect both an S-video cable and a standard video cable to VIDEO 3 at the same time or the picture performance will be unacceptable.

To view the camcorder video:



Select the VIDEO 3 video input source on the TV.*

______________

* To select the video input source, press INPUT on the remote control (see page 72).

To program the TV remote control to operate other devices, see Chapter 3.

Camcorder

VIDEO

AUDIO

OUT

VIDEO 3 inputs

on TV right side panel

Page 16

Chapter 2: Connecting your TV

Connecting a VCR and Cable box

You will need:

 one signal splitter  five coaxial cables  two sets of standard A/V cables

• For better picture performance from your VCR: If your VCR has S-video, connect an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect an S-video cable and a standard video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out terminal using the white audio cable only.

• When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.

To view basic Cable channels and use the TV’s features:



Select the ANT 1 video input source on the TV.* Use the TV controls (front panel or remote control) to change channels and access the TV’s features.

To view basic and premium Cable channels:



Turn OFF the VCR. Select the ANT 2 video input source on the TV.* Tune the TV to channel 3 or 4 (whichever channel the Cable box output is set to). Use the Cable box controls to change channels.

Cable box Signal splitter

OUT

CH 3 CH 4

IN from ANT

OUT to TV

Stereo VCR

CH 3 CH 4

OUT

VIDEO AUDIO

From Cable TV

OUT

To view the VCR:



Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

Note: A VIDEO 1 connection with an S-Video cable (instead of a standard video cable) will provide better picture performance (as mentioned in the first bulleted item at the top of this page).

_____________

Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input mode is selected.*

* To select the video input source, press INPUT on the remote control

(see page 72). To program the TV remote control to operate other devices, see Chapter 3.

To enable the TV Guide On Screen® system to work



with your cable box and to use the TV Guide On Screen

1. Connect the G-LINK

recording features:

cable according to the instructions

on page 28.

2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen

system.

5. See Chapter 7 for details on using the TV Guide

On Screen

system.

Page 17

Chapter 2: Connecting your TV

Connecting a VCR and satellite receiver

You will need:

 one signal splitter  four coaxial cables  one set of component video cables (if your

satellite receiver does not have component video, connect the standard A/V cables only)

 one pair of standard audio cables  three sets of standard A/V cables

• For better picture performance, if your satellite receiver and VCR have S-video, connect S-video cables (plus audio cables) instead of the standard video cables. Do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s AUDIO OUT terminal using the white audio cable only.

To view satellite programs using the component video



connections:

Select the ColorStream HD-1 video input source on the TV.*

To view satellite programs using the standard



video connections or to record satellite programs:

Turn on all three devices. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details). Select the VIDEO 2 video input source on the TV.*

From antenna

Signal splitter

OUT

IN from ANT

OUT to TV

From satellite dish

S-VIDEO

OUT

COMPONENT VIDEO

Satellite

Stereo VCR

CH 3 CH 4

PBP

VIDEO AUDIO

Satellite receiver

VIDEO

OUT

AUDIO

OUT

LRL

To view the VCR or view and record antenna channels:



Turn ON the VCR. Tune the VCR to the channel you want to watch. Select the VIDEO 1 video input source on the TV.*

Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input mode is selected.*

_____________

* To select the video input source, press INPUT on the remote control

(see page 72). To program the TV remote control to operate other devices, see Chapter 3.

To use the TV Guide On Screen® recording features:



1. Connect the G-LINK

cable according to the instructions

on page 28.

2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen

5. See Chapter 7 for details on using the TV Guide On Screen

Note: The TV Guide On Screen® system does not receive program listings from or for any satellite service.

system.

Page 18

Chapter 2: Connecting your TV

Connecting a DVD player with S-video, a VCR, and a Cable box

You will need:

 one signal splitter  five coaxial cables  two sets of standard A/V cables

Note: If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s audio out terminal using the white audio cable only.

 one S-video cable  one pair of standard audio cables

Note:

• If your DVD player does not have S-video, use a standard video cable instead. Do not connect an S-video cable and a standard video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• Do not connect the DVD player and VCR to the same set of A/V inputs on the TV. (See the illustration, which shows the VCR connected to VIDEO 1 on the TV, and the DVD player connected to VIDEO 2.)

• If your DVD player has component video, see page 19.

To view basic channels and access the TV’s features:



Select the ANT 1 video input source.* Use the TV controls to change channels and access the TV’s features.

To view premium Cable channels:



Turn OFF the VCR. Select the ANT 2 video input source on the TV.* Tune the TV to channel 3 or 4 (whichever channel the Cable box output is set to). Use the Cable box controls to change channels.

Note: When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.

From antenna or Cable TV

Cable box

OUT

CH 3 CH 4

Signal splitter

OUT

Stereo VCR

IN from ANT

OUT to TV

CH 3 CH 4

VIDEO AUDIO

OUT

AUDIO

OUT

S-VIDEO

OUT

VIDEO

OUT

DVD player with S-video

Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input mode is selected.*

To view the DVD player:



Turn ON the DVD player. Select the VIDEO 2 video input source on the TV.*

To view the VCR:



Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

_____________

* To select the video input source, press INPUT on the remote control

(see page 72). To program the TV remote control to operate other devices, see Chapter 3.

To enable the TV Guide On Screen® system to work with



your cable box and to use the TV Guide On Screen

recording features:

1. Connect the G-LINK

cable according to the instructions on

page 28.

2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide

On Screen

system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

Page 19

Chapter 2: Connecting your TV

Connecting a DVD player with ColorStream® (component video) and a VCR

Your TV has ColorStream® (component video) inputs.

You will need:

 one signal splitter  three coaxial cables  two sets of standard A/V cables

• For better picture performance, if your VCR has S-video, use an S-video cable (plus audio cables) instead of the standard video cable. However, do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s audio out terminal using the white audio cable only.

 one pair of standard audio cables  one set of component video cables

• You can connect the component video cables (plus audio cables) from the DVD player to either set of ColorStream terminals on the TV (HD-1 or HD-2). The ColorStream HD-1 and HD-2 terminals can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems. A 1080i signal will provide the best picture performance.

• If your DVD player does not have component video, see page

18. If your DVD player has HDMI video, see page 21.

To view antenna or Cable channels:



Select the ANT 1 video input source on the TV.*

To view the DVD player:



Turn ON the DVD player. Select the ColorStream HD-1 video input source on the TV.*

To view the VCR:



Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

From antenna or Cable

Signal splitter

OUT

Stereo VCR

VIDEO AUDIO

IN from ANT

OUT to TV

CH 3 CH 4

OUT

AUDIO

OUT

S-VIDEO

OUT

PBP

COMPONENT VIDEO

VIDEO

OUT

DVD player with component video

Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input mode is selected.*

To record a TV program while watching a DVD:



Turn ON the VCR. Tune the VCR to the channel to record. Select the ColorStream HD-1 video input source on the TV* to view the DVD.

_____________

* To select the video input source, press INPUT on the remote control

(see page 72). To program the TV remote control to operate other devices, see Chapter 3.

To use the TV Guide On Screen® recording features:



1. Connect the G-LINK

cable according to the instructions

on page 28.

2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen

5. See Chapter 7 for details on using the TV Guide On Screen

system.

Page 20

Connecting two VCRs

Chapter 2: Connecting your TV

You will need:

 one signal splitter  three coaxial cables  two sets of standard A/V cables

• For better picture performance, if VCR 1 has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. However, do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If VCR 1 has mono audio, connect L/MONO on the TV (VIDEO 1) to the audio out terminal on VCR 1 using the white audio cable only.

• Do not connect the same VCR to the output and input terminals on the TV at the same time.

To view the antenna or Cable signal:



Select the ANT-1 video input source on the TV.*

To view VCR 1:



Turn ON VCR 1. Select the VIDEO 1 video input source on the TV.*

To dub or edit from VCR 1 to VCR 2:



Turn ON both VCRs. Set VCR 2 to the appropriate line input (refer to your VCR owner’s manual for details). Select the VIDEO 1 video input source on the TV.*

Note:

• If you have a Cable box, connect the Cable box and splitter to VCR1 as shown on page 16.

• The VIDEO OUT signal incorporates Macrovision

_________________________________________________________________

* To select the video input source, press INPUT on the remote control

(see page 72). To program the TV remote control to operate other devices, see Chapter 3.

** Do not connect the TV through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the TV.

*** This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Macrovision is a registered trademark of Macrovision Corporation.

From antenna or Cable

Signal splitter

OUT

VCR1 (plays)

VIDEO AUDIO

IN from ANT

OUT to TV

CH 3 CH 4

OUT

VCR2 (records)

VIDEO AUDIO

IN from ANT

OUT to TV

The VIDEO OUT terminal does not output the POP picture.

When POP mode is active, the AUDIO OUT terminals output the sound of the active window (main or POP). For additional information, see “Notes about recording” on page 81.

Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input mode is selected.*

To use the TV Guide On Screen® recording features:



1. Connect the G-LINK on page 28.

2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen

5. See Chapter 7 for details on using the TV Guide On Screen

system.

CH 3 CH 4

cable according to the instructions

OUT

Page 21

Chapter 2: Connecting your TV

Connecting an HDMI™ or DVI device to the HDMI input

The HDMI uncompressed digital video from an HDMI device, or uncompressed digital video from a DVI

This input is designed to accept HDCP digital form from EIA/CEA-861/861B–compliant

[1]

input on your TV receives digital audio and

[2]

device.

[3]

program material in

[4]

consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with 720p signals but will also accept and display 1080i, 480i, and 480p signals.

NOTE: DO NOT CONNECT A PC USING THE

HDMI PORT. ALWAYS use the TV’S PC IN (VGA)

port to connect a PC.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector) per HDMI device

For proper operation, it is recommended that you use as short an HDMI cable as possible. You should not encounter difficulty if you use an HDMI cable shorter than

16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables.

See “Setting the HDMI™ audio mode” on page 55.

HDMI device

HDMI OUT

VIDEO AUDIO

OUT

__________________________________________________________________

[1]

HDMI = High-Definition Multimedia Interface.

[2]

DVI = Digital Video Interface.

[3]

HDCP = High-bandwidth Digital Content Protection.

[4]

EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

Note: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

• When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

• When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

• one HDMI-to-DVI adapter cable (HDMI type A connector) per DVI device

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is

6.6 ft (2m).

• one pair of standard analog audio cables per DVI device

An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below).

See “Setting the HDMI™ audio mode” on page 55.

DVI device

DVI/HDCP

OUT

VIDEO AUDIO

OUT

___________

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDM I Licensing LLC.

Page 22

Chapter 2: Connecting your TV

Connecting a device to the TheaterNet OUT infrared terminal using the IR blaster cable for IR pass-through device control

You can use the TV’s TheaterNet OUT* infrared terminal (IR pass-through) to remotely operate—through the TV—many infrared remote-controlled devices (such as Toshiba infrared remote-controlled VCRs or DVD players) enclosed within an entertainment center or similar cabinet. Without the TheaterNet OUT connection, the device typically would need to be visible to operate it remotely.

You will need:

 one dual-wand IR blaster cable (included with your TV)

 other audio/video cables as required to connect the device(s)

to the TV (see pages 15–21)

To connect the IR blaster cable:

1. Locate the infrared sensor on the front of your device. This sensor is marked on some devices.**

2. Align one of the IR blaster cable’s wands about 1 inch away from the infrared sensor on the front of the device and attach it using double-sided mounting tape. If you have a second device, attach the second wand in a similar manner.

(See illustration at right.)

Note: If you do not have a second device, coil the second wand with a rubber band and leave it behind the TV.

3. Plug the IR blaster cable’s plug into one of the TV’s TheaterNet OUT terminals.

Front of IR-controlled DVD player (for example)

Front of IR-controlled audio device (for example)

Infrared

sensor

IR blaster cable wand (approx. 1 inch from device)

Back of TV

To control the device(s):

Point the TV remote control (that you previously programmed to operate the device; see Chapter 3) or the device’s remote control at the front of the TV and press the button for the desired function. The signal passes from the remote control through the TV to the device via the IR blaster cable.

Note:

• If you use the device’s remote control to operate the device, you also will need to use the TV’s remote control to operate the TV.

• For additional control options, see “TheaterNet on-screen device control” on the next page.

MENUVOLUMECHANNELEXITTV/VIDEO POWER

If you cannot locate the device’s infrared sensor:

1. Turn OFF the device.

2. Starting at the lower left corner of the device, place the end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.)

3. If the device turns on, the point at which the remote control touched the device is the location of the sensor.

4. If the device does not turn on, move the remote control slightly to the right and press POWER again.

5. Repeat step 4 until you locate the device’s infrared sensor.

___________

The TheaterNet OUT function has been verified for use with Toshiba infrared-controlled devices.

Page 23

Chapter 2: Connecting your TV

Connecting an IR receiver/repeater or home theater control system to the TheaterNet IN infrared terminal

For additional control options for your home theater system, you can connect an IR receiver/repeater (not included) or a home theater control system (not included) to the TV’s TheaterNet IN infrared terminal.*

See the Specifications section in the back of this manual for TheaterNet IN terminal requirements.

Contact your home theater electronics dealer for details about IR receivers/repeaters and home theater control systems.

You will need:

 one IR cable

TV back panel

TheaterNet™ on-screen device control

For additional control options for your home theater system, set up the TheaterNet on-screen device control feature. You can use this feature to control many IR remote-controlled devices and IEEE1394 devices using the on-screen control icons.

See pages 50–54 for details on setting up and using TheaterNet.

See pages 25–27 for details on connecting IEEE1394 devices.

Note: The TheaterNet on-screen icons are the only device functions available when the icons are on-screen. To access other device functions, close the TheaterNet icon window.

Toshiba Video 3

ENTER

EXITTOP MENU

MENUVOLUMECHANNELEXITTV/VIDEO POWER

OUT

Back of IR receiver/repeater or home theater control system* (not included)

To operate the TV with this connection, point the Toshiba TV remote control toward the front of the IR receiver/ repeater or home theater control system.

IR receiver/repeater or home theater control system

MENUVOLUMECHANNELEXITTV/VIDEO POWER

___________

The TheaterNet IN function has been verified for use with SmarTouch™ STS/STS-C wireless RF control systems. Due to the wide

variation in remote control operation among manufacturers, these functions may or may not operate with other brands. SmarTouch is a trademark of Crestron Electronics, Inc. (www.crestron.com).

Page 24

Chapter 2: Connecting your TV

Connecting a digital audio system

The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby* Digital

or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby Digital decoder or other external audio system with optical audio input.

You will need:

 one optical audio cable (Use an optical audio cable that has

the larger “TosLink” connector and not the smaller “mini-optical” connector.)

To control the audio:

1. Turn on the TV and the digital audio device.

2. Press MENU on the TV’s remote control and open the AUDIO menu.

3. Highlight Audio Setup

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

and press ENTER.

4. In the Optical Output Format field, select either Dolby Digital or PCM, depending on your device (see “Selecting the optical audio output format” on page 93).

Audio Setup

MTS Stereo

Language English

Speakers On

Optical Output Format

Reset

Dolby Digital

Done

5. Turn off the TV’s built-in speakers in the same Audio Setup menu (above). Also see “Turning off the built-in speakers” on page 93.

Dolby Digital decoder or

other digital audio system

Optical

Audio IN

LINE IN LR

Note:

• Some audio systems may not be compatible with Dolby Digital bitstream signals. Older audio systems that are not compatible with standard optical out signals may not work properly, creating a high noise level that may damage speakers or headphones. THIS DAMAGE IS NOT COVERED BY YOUR WARRANTY.

• The DIGITAL AUDIO OUT terminal outputs signals only when receiving digital broadcasts with the TV in single-window mode.

• The DIGITAL AUDIO OUT terminal may not output some digital audio sources because of copy restrictions.

___________

*Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.

Connecting an analog audio system

This connection allows you to use external speakers with an external analog audio amplifier to adjust the sound level.

You will need:

 one pair of standard audio cables

To control the audio:

1. Turn on the TV and the stereo amplifier.

2. Turn off the TV’s built-in speakers (see “Turning off the built-in speakers” on page 93).

Note: To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set to a reasonable listening level.

Analog audio amplifier

LINE IN LR

Page 25

Chapter 2: Connecting your TV

Connecting IEEE1394 video devices

You can use the two bi-directional IEEE1394 ports on the back of your TV to connect digital video devices that meet CEA specifications for IEEE1394.

Because these ports are bi-directional, they can be used for both playback and recording.

• Because IEEE1394 is an evolving technology, it is possible that some or all of the connectivity features of a device you connect to the TV through the IEEE1394 ports may not operate. You should confirm that the devices you want to use with the IEEE1394 ports will operate with those ports.

• This TV does not support all possible IEEE1394 signal types. For information on signals supported by the IEEE1394 ports, see

“Supported signals” at right.

• IEEE1394 cable carries both audio and video information;

separate audio cables are not required.

You will need:

 one (or two) IEEE1394 cables

Note: The transmission capability of IEEE1394 cable used with this TV must be S400 (400 Mbps maximum).

 additional A/V cables if your device is analog-compatible

(see “Using analog-compatible IEEE1394 devices” below).

TV back panel

Supported signals

The IEEE1394 ports support only the signals listed below. Even though incompatible video, audio, and digital control signals cannot be decoded by the TV, these signals may be passed through the IEEE1394 cable to other compatible devices. Incompatible devices may not appear in the TheaterNet

• MPEG-2 digital video signals

Other digital video signals—such as DV video—are incompatible and must be decoded by the source device and sent to the TV as analog video (composite or S-video).

• Dolby Digital and MPEG digital audio signals

Other digital audio signals (such as DPM, MP3, and DTS) are incompatible and cannot be decoded by the TV.

• EIA-775 and AV/C digital control

Your TV can serve as the control center for many devices that are compatible with EIA-775 or AV/C IEEE1394 control standards (described below).

The TV cannot control IEEE1394 devices that use any other control standards.

– EIA-775 digital control allows tuning devices (such as

Cable boxes) to send simple graphics; however, this standard does not allow the TV to control the Cable box through IEEE1394.

– AV/C (audio/video control) provides basic control (such

as power, play, stop, rewind, fast-forward, pause, and record), as applicable to the specific device.

™

menu.

}

Two bi-directional

IEEE1394 ports From IEEE1394 devices (such as AVHD or D-VHS)

Using analog-compatible IEEE1394 devices

Some digital IEEE1394 devices are compatible with analog signals. For example, some D-VHS VCRs can record and play

VHS or S-VHS format videos. Such devices allow you to play analog tapes that you rented or recorded, or record analog programs from antenna or Cable TV systems. To use the IEEE1394 device’s analog features, you need to connect the device to the TV using standard A/V cables (or S-video plus audio cables) in addition to connecting the IEEE1394 cable.

Note: If you have an IEEE1394 device connected to both digital and analog inputs on the TV, the TV automatically switches between digital and analog modes, as needed, when the initial device access is initiated using the TheaterNet button.

See page 50 for details on using the TheaterNet feature.

Using TheaterNet™ on-screen device control

You can use the TheaterNet feature to control some IEEE1394 devices using on-screen control icons. See page 50 for details on setting up and using the TheaterNet feature.

Note: If the TheaterNet feature does not control your IEEE1394 device, you can either use the device’s remote control or try using IR pass-through with the TV’s remote control (page 22).

Page 26

Chapter 2: Connecting your TV

Connecting IEEE1394 video devices (continued)

Connecting an AVHD (external hard drive) or D-VHS digital recorder

IEEE1394 device initialization

When you connect a new IEEE1394 device to the TV and turn it on, the device immediately announces its presence to the TV

You can connect an IEEE1394-compatible D-VHS or AVHD (audio/video hard drive) digital recorder (such as Toshiba’s

™

Symbio

AVHD Recorder) to record high definition and

standard definition material from either tuner and control live

(and other networked IEEE1394 devices, if any), and the “New IEEE1394 Device Initialization” screen (shown in step 2, below) automatically appears.

TV (pause, rewind, etc.).

When you connect an AVHD or D-VHS device to the TV:

• The remote control keys (LIVE, REW, PAUSE, PLAY, etc.) are automatically activated to allow control of live TV.

• The TV Guide On Screen

system is automatically configured to allow recording to the device.* See Chapters 5 and 7 for details. Also see page 55 for details on setting the AVHD device skip time.

• Some programs may not be recorded due to copy protection restrictions.

This TV is compatible with the new Toshiba

Audio/Video Hard Drive Recorder!

Toshiba’s Symbio™ AVHD Recorder is designed specifically for high definition television (HDTV) and offers control over digital video recording and playback.

Think of it as a “tapeless VCR” for digital television. You can pause, rewind, or use instant replay, so you’ll never miss a thing!

Symbio also offers one-touch recording* of both standard and High Definition programs through the no-fee TV Guide On Screen

To enjoy the full benefits of your Symbio AVHD Recorder, you must first set

up the TV Guide On Screen® system (see Chapter 5). Full Symbio AVHD Recorder benefits, including Intelligent One Touch recording, will not be available unless the TV Guide On Screen® system is fully operational. However, even if the TV Guide On Screen® system is not fully operational, manual recording is available as long as the TV Guide On Screen® system has acquired the necessary date and time data. If you experience any issues with your Symbio AVHD Recorder, please contact Toshiba Consumer Solutions by calling (800) 631-3811 or visiting

http://www.tacp.com/customersupport/contact.asp.

interactive program guide built in to this TV.

Note: With some devices, it may take up to one minute for the IEEE1394 Device Initialization screen to appear.

1. If you also connected your IEEE1394 device to an analog input, use the

yzx •

buttons to select the input in the ANALOG INPUT USED field; otherwise, leave it set to “None.” (See “Using analog-compatible IEEE1394 devices” on page 25.)

2. To label the device, highlight Edit Label and press ENTER.

New IEEE1394 Device Initilization

Manufacturer

Device Type

Custom Label

3. Press the

Edit Label Done

yzx •

TOSHIBA

AVHD

buttons to select a character for the first

space and then press ENTER.

4. Repeat step 3 to enter the rest of the characters.

5. Highlight Done and press ENTER to save the information.

IEEE1394 Device Label Edit

MY DEVICE_

ABCDEFG

HI JKLMN

OPQRS TU

VWX Y Z 0 1

2345678

SPC CLR BS

Cancel Done

Note:

• The TV may not recognize incompatible or non-A/V IEE E1394 devices; however, these devices may still be available to other compatible IEEE1394 devices on the network.

• You may be able to use the TV’s remote control to operate some compatible IEEE1394 devices. You must first program the remote control to recognize the device (see Chapter 3). If you have an IEEE1394 Cable box or satellite receiver, you may need to use the remote control that came with the device.

• Toshiba is not liable for the operation of any IEEE1394 device other than the Toshiba Symbio AVHD recorder.

Page 27

Chapter 2: Connecting your TV

Connecting IEEE1394 video devices (continued)

IEEE1394 device management

The IEEE1394 device information is saved in the TV’s memory. You can edit this device information (for example, edit the device name, change the analog input information, or delete the device information from the TV’s memory if you no longer use that device).

To edit the IEEE1394 device information:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3 below).

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

3. Open the Devices menu, highlight IEEE1394 Devices, and press ENTER.

Devices

IEEE1394 Devices

TheaterNet Devices

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

Important information regarding

IEEE1394 device interconnection

• Never loop the last device in the chain back to the TV.

If the device chain is looped, the TV may not work properly with the other devices in the chain.

• Always place devices with the slowest communication speed at the end of each chain. If a device with a slower

communication speed is placed ahead of a faster device in the chain, the signal from the slower device will interfere with the signal from the faster device. To determine the communication speed of an IEEE1394 device, look for an “S” number near the device’s IEEE1394 connector. The higher the “S” number, the faster the device. If your device is not marked with an “S” number, look in the device’s user manual or call the device manufacturer’s technical support number.

• If your IEEE1394 device has a two-position power switch, always place the device at the end of the chain and turn ON the power switch when any device is used.

If the power switch is OFF, it will interfere with signals from devices behind it in the chain.

• The maximum length for an IEEE1394 cable between each device is 15 feet.

• This TV is an IEEE1394A device. The IEEE1394B protocol is faster and intended to allow for longer distances between devices and multi-room systems. IEEE1394A–to–IEEE1394B converters (available at some electronics suppliers) may allow compatibility of IEEE1394B devices with your existing IEEE1394A devices.

• The transmission capability of IEEE1394 cable used with this TV must be S400 (400 Mbps maximum).

Navigate

Select

Back Exit

CH RTN

EXIT

4. Highlight the device you want to edit and press ENTER.

IEEE1394 Device Management

Brand Type Label Analog Input Used Connected

TOSHIBA AVHD None No

MY DEVICE

Reset

Done

5. Follow the on-screen prompts to modify the device information.

Page 28

G-LINK® connection

Chapter 2: Connecting your TV

• This connection is necessary for the TV Guide On Screen® system to work with your cable box to receive program listings and to enable the TV Guide On Screen

• This connection is not necessary for AVHD or D-VHS recording devices. See pages 26 and 55 for further details.

After you connect your devices to the TV, you will need to connect the G-LINK® cable (either of the dual-wand IR blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK

Note: TV Guide On Screen® program data is available through the ANT-1 and ANT-2 antenna inputs and also through the VIDEO 1 inputs if you have a cable box connected to VIDEO 1. TV Guide On Screen connection information on pages 15–27.

recording features with your VCR.

program data is not available through any other inputs on this TV. See the

terminal on the TV.

The G-LINK® connection is necessary to enable the following features of your TV Guide On Screen® system:

• If you have a Cable box, you must connect the G-LINK TV Guide On Screen

• If you have a VCR, you must connect the G-LINK On Screen

recording features.

program listings for your Cable service.

To connect to the G-LINK® terminal:

cable from the Cable box to the G-LINK® terminal to receive the

cable from the VCR to the G-LINK® terminal to use the TV Guide

Front of Cable box

1. Locate the infrared sensor on the front of your VCR or Cable box. The sensor is marked on some devices.*

2. Align one of the G-LINK

(IR blaster) cable’s wands about 1 inch away from the infrared sensor on the front of the VCR and attach it using double-sided mounting tape.

If you have a Cable box, attach the other wand in a similar

Front of VCR

manner. (See illustration at right.)

Note: If you do not have a Cable box, coil the second wand with a rubber band and leave it behind the TV.

3. Plug the G-LINK® (IR blaster) cable’s plug into the TV’s G-LINK

For details on setting up the TV Guide On Screen

terminal.

system:

See Chapter 5.

Infrared

sensor

G-LINK® (IR blaster) cable wand (approx. 1 inch from device)

Back of TV

For details on using the TV Guide On Screen

interactive

program guide:

See Chapter 7.

If you cannot locate the device’s infrared sensor:

1. Turn OFF the device.

3. If the device turns on, the point at which the remote control touched the device is the location of the sensor.

4. If the device does not turn on, move the remote control slightly to the right and press POWER again.

5. Repeat step 4 until you locate the device’s infrared sensor.

Page 29

Chapter 2: Connecting your TV

Connecting a personal computer (PC)

This connection allows you to view the image from a PC on the TV screen. When connecting a PC to the TV, use an analog RGB (15-pin) computer cable and a PC audio cable.

– To use a PC, set the monitor output resolution on the

PC before connecting it to the TV. The following signals can be displayed:

• VGA: 640 × 480 @ 60Hz

• SVGA: 800 × 600 @ 60Hz

• XGA: 1024 × 768 @ 60Hz Other formats or non-standard signals may not be

displayed correctly.

– To display the optimum picture, use the PC setting

feature (see “Using the PC setting feature” on page 95).

Signal names for mini D-sub 15-pin connector

Pin assignment for RGB/PC terminal

610

1115

Pin No. Signal name

4 NC (not connected)

5NC

6 Ground

7 Ground

8 Ground

9NC

10 Ground

11 NC

12 NC

13 H-sync

14 V-sync

15 NC

PC audio cable

Computer

PC audio output

Conversion adapter (if necessary)

Note:

• Some PC models cannot be connected to this TV.

• An adapter is not needed for computers with a DOS/V compatible

mini D-sub 15-pin terminal.

• Depending on the DVD’s title and the specifications of the PC on which you are playing the DVD-Video, some scenes may be skipped or you may not be able to pause during multi-angle scenes.

Page 30

Chapter 2: Connecting your TV

Connecting a home network

The Toshiba Home Interactive Network Connection (THINC®) feature allows you to network the TV with your home PC (personal computer), which will allow access to the TV’s file sharing and e-mail scheduling features.

■ File sharing

You can access JPEG and MP3 files that are stored on your networked home PC and view/play them on the TV.

• Connect your TV to your PC /network according to either Example #1 or Example #2, below left.

• Does NOT require Internet/e-mail service.

Note:

■ E-mail scheduling of recordings and reminders

You can schedule recordings and reminders by sending an email to the TV from any PC. (This connection also allows access

to file sharing.)

• Connect your TV to your home network according to Example #3, below right.

• Requires the following: – Home Internet service. – A dedicated POP3 e-mail address for the TV (different from

your personal e-mail address).

– A compatible recording device.

• Contact your ISP (Internet Service Provider) to obtain and set up Internet/e-mail service.

• See Chapter 2 for recording device connection instructions.

Example #1: Connecting the TV to a home network

without an Internet connection (for file sharing only)

You will need:

 two or more standard

Ethernet (RJ-45)

cables (the number of cables depends on the number of PCs you connect to your network)

 one hub or switch

TV back panel

Hub or switch

• The TV’s home network feature is compatible only with Microsoft Windows® 2000 and the Home or Professional version of Microsoft Windows® XP Service Pack 1 and Service Pack 2. See Chapter 11 for details.

• The TV’s home network connection allows access to e-mail scheduling and file sharing only. You will NOT be able to use

the TV to access the Internet.

• If you use an Ethernet crossover cable to connect your PC directly to the TV, you will not be able to use the automatic setup and must manually set up the network address.

• If you use a hub or switch to connect the TV to your home network, you will not be able to use the automatic setup and must manually set up the network address.

• If you use a router with built-in DHCP functionality, use the automatic setup. Manual setup may not work.

Example #3: Connecting the TV to a home network

You will need:

 one coaxial or telephone cable (depending on your modem)  three standard Ethernet (RJ-45) cables  one Ethernet router/switch  one modem (DSL or cable)

See Chapters 10 and 11

for details on configuring

and using e-mail scheduling,

file sharing, the JPEG Picture

Viewer, and the MP3 Audio Player.

with an Internet connection (for e-mail scheduling and file sharing)

[1]

TV back panel

Example #2: Connecting the TV directly to a PC

without an Internet connection (for file sharing only)

TV back panel

You will need:

 one Ethernet crossover

cable (i.e., a PC-to-PC direct file transfer cable)

Note: Do NOT use standard Ethernet cable with this connection.

Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.

Ethernet

crossover

cable

Modem (DSL or cable)

[2]

Cable or phone jack [4]

_____________ [1] Your router/switch may be part of your DSL or cable modem. Your switch

may be separate from your router. For assistance, contact your ISP or an IT professional.

[2] Coaxial or telephone cable (depending on your modem type) [3] Standard Ethernet (RJ-45) cable

[4] Do NOT connect a phone jack directly to the TV’s RJ-45 (Ethernet) port.

Router/switch[1]

[3]

Page 31

Using the remote control

Learning about the remote control

The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the remote control functional key chart on pages 34–35.

For a list of the buttons that operate the TV Guide On Screen page 59.

POWER

turns the TV on and off. Press POWER to turn on the TV. The red LED indicator on the TV front touchpad will be illuminated. Press POWER again to turn off the TV.

Note: The Quick Restart™ setting will affect the amount of time it takes for the picture to appear when you turn on the TV. See page 56 for details.

SLEEP

accesses the sleep timer (page 94).

LIGHT

The first press of the LIGHT button lights the keypad and turns on the Illumination mode. With the Illumination mode on, pressing any key lights the keypad for 5 seconds (10 seconds if you’re in programming mode). Subsequent presses of the LIGHT button toggle between turning the Illumination mode on and off.

system, see

Channel Numbers (0–9, –/100)

directly tune channels. The “–” button is used to tune digital channels (page 76) or to display the favorite channel list (page 49).

INPUT

selects the video input source (page 72).

MODE

cycles through the six remote control device modes: TV, CBL/SAT, VCR/PVR, DVD, AUDIO1, and AUDIO2. The mode indicator light will remain lit for a few seconds (page 33).

PIC SIZE

cycles through the five pictures sizes: Natural, TheaterWide 1/2/3,

and Full (page 77).

TheaterNet™ DEVICE

TheaterNet™ CTRL

accesses the main TV menu system (pages 40 and 41) or opens a menu in the TV Guide On Screen

TV GUIDE

INFO

On Screen

ENTER

opens the TV Guide On Screen® system (Chapter 7).

provides detailed information on highlighted items in the TV Guide

system (Chapter 7).

activates highlighted items in the main menu system and the TV Guide On Screen

Arrow buttons (yz x •)

adjust programming menus. (Also see

CH yz

cycles through programmed channels when no menu is on-screen (page

47) and functions as page up/down when a menu is on-screen or when the TV Guide On Screen

displays a list of available TheaterNet devices (page 50).

accesses the on-screen IR device control icons (page 51).

system (Chapter 7).

system.

When a menu is on-screen, these buttons select or

x / • on the next page.)

system is open (Chapter 7).

(Continued on next page)

Note: The message “Not Available” will appear if you press a key for a function that is not available

Page 32

Chapter 3: Using the remote control

Learning about the remote control (continued)

VOL yz

adjusts the volume level.

EXIT

closes on-screen menus and the TV Guide On Screen® system.

CH RTN

returns to the last viewed channel (page 76), or stops the picture viewer slide show

(page 104).

Live

returns viewing of the TV back to the live program, while continuing to record to the Toshiba

Symbio™ AVHD recorder (pages 26 and 55).

RECALL

displays TV setting information on-screen (page 96).

MUTE

reduces or turns off the sound (page 90).

TV/VCR

selects TV mode to view one program while recording another.

SKIP SS

and

jump forward and backward one day in the TV Guide On Screen

listings (Chapter 7).

LIST

displays the Toshiba Symbio™ AVHD recorder play list (if available) (page 26).

FAV CH yz

HOME ( )

x / •

tunes to the next higher/lower favorite channel (page 49).

accesses the home function of the Channel Browser™ feature (page 75)

While watching TV, these buttons open the Channel Browser banner and tune to the previous/next channel in the channel history (page 74). (Also see “Arrow buttons” on previous page.)

SPLIT

turns the POP feature on and off (page 81) or locks/unlocks the TV Guide On Screen

video window (page 60).

PIC MODE

FAV SCAN

FREEZE

selects the picture mode (page 84).

accesses the favorite channel search function (page 83).

accesses the freeze feature (page 83).

Remote control effective range

For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV.

Point remote control toward remote sensor on front of TV.

16.4 ft (5m)

Page 33

Chapter 3: Using the remote control

Installing the remote control batteries

To install the remote control batteries:

Caution: Always dispose of batteries in a designated disposal location. Never throw batteries into a fire.

1. Slide the battery cover off the back of the remote control.

2. Install two “AA” size alkaline batteries. Match the + and – symbols on the batteries to the symbols on the battery compartment.

3. Slide the battery cover on to the remote control until the lock snaps.

Caution:

Never throw batteries into a fire.

Note:

• Be sure to use AA size batteries.

• Dispose of batteries in a designated disposal area.

• Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

• If the remote control does not operate correctly, or if the

operating range becomes reduced, replace the batteries with new ones.

• When necessary to replace batteries in the remote

control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

• Always remove the batteries from the remote control if

they are dead or if the remote control will not be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Using the remote control MODE button to control your other devices

Your TV remote control has one dedicated TV mode and five programmable multi-brand modes: CBL/SAT, VCR/PVR, DVD, AUDIO 1, and AUDIO 2. The default device modes and programmable device modes are listed below.

Note: The TV remote control is preprogrammed to operate most Toshiba devices. If you own a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other devices” on page 36.

MODE Default device mode control (before programming)

1) TV Toshiba TV

2) CBL/SAT Toshiba Satellite receiver

3) VCR/PVR Toshiba VCR

4) DVD Toshiba DVD

5) AUDIO 1 Pioneer Audio receiver

6) AUDIO 2 Pioneer LD

MODE Device mode control after programming

1) TV Toshiba TV

2) CBL/SAT

3) VCR/PVR

4) DVD Multi-brand video/audio devices

5) AUDIO 1

6) AUDIO 2

You can directly select the device mode by pressing the corresponding number button (1–6) while pressing the MODE button.

Number (1-6)

MODE

Note:

Although the TV remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s remote control or the control buttons on the device.

Page 34

Chapter 3: Using the remote control

Remote Control functional key chart

REMOTE

CONTROL

MODE LIGHT SLEEP POWER 1 2 3 4 5 6 7 8 9 0 100/ –

KEY

TV CBL/SAT CBL/SAT DVD AUDIO 1 or 2 AUDIO 1 or 2 VCR/PVR VCR/PVR

(Toshiba TV) (Cable Box) (Satellite Box) (LD) (Receiver) (CD Player) (VCR) (PVR)

Toggles among the remote control device modes Lights the remote key, and toggles between enabled and disabled Illumination mode.* Sleep timer --- --- --- --- --- --- --Power Power Power Power Power Power Power Power Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 Digit 1 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 Digit 2 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 Digit 3 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 Digit 4 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 Digit 5 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6 Digit 6 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 Digit 7 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 Digit 8 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 Digit 9 Digit 0 Digit 0 Digit 0 Digit 0 --- Digit 0, 10 Digit 0 Digit 0 – (digital --- – (sub +10 --- --- 100 ---

REMOTE CONTROL DEVICE MODE

- separator) channel)

INPUT

TV/Video TV TV TV TV TV TV TV select

PIC SIZE

Selects the TV TV TV TV TV TV TV image shape

MENU/ ACTION

TV GUIDE/SETUP INFO/

TOP MENU TheaterNet

DEVICE/SUBTITLE TheaterNet

CTRL/AUDIO ENTER

y Menu select --- Menu select Menu select --- --- --- Menu select

Menu/ --- Action, Menu --- --- --- Menu Guide Menu Menu

TV Guide --- Guide DVD setup --- --- --- Guide Guide Info --- INFO Top menu --- --- --- INFO

TheaterNet

--- --- Subtitle --- --- --- ADVANCE

Device TheaterNet

--- --- Audio --- --- --- ---

Control Enter --- Enter, Select Enter --- --- --- Enter

up up up up

z Menu select --- Menu select Menu select --- --- --- Menu select

down down down down

x • Menu select --- Menu select Menu select --- --- --- Menu select

left/right left/right left/right left/right

EXIT

/ Exit --- Exit DVD clear --- --- --- Exit

DVD CLEAR

yz Channel Channel Channel --- Channel --- Channel Channel

CH PAGE +/–

up/down, up/down up/down up/down up/down up/down Page up/down

VOL

yz Volume Volume Volume Volume Volume Volume Volume Volume

up/down*2up/down*2up/down*2up/down*2up/down*2up/down*2up/down*2up/down*

CH RTN/ DVD RTN

Live RECALL

Previous Previous Previous DVD --- --- --- --channel channel channel return

Live --- --- --- --- --- --- Live TV On-screen

--- ---

On-screen --- --- ---

---

display display

Page 35

Chapter 3: Using the remote control

Remote Control functional key chart (continued)

REMOTE

CONTROL

KEY MUTE SLOW

SKIP

REW PAUSE/STEP PLAY FF TV/VCR DISC/AM/FM STOP REC

LIST FAV CH

HOME SPLIT PIC MODE FAV SCAN FREEZE

REMOTE CONTROL DEVICE MODE

TV CBL/SAT CBL/SAT DVD AUDIO 1 or 2 AUDIO 1 or 2 VCR/PVR VCR/PVR

(Toshiba TV) (Cable Box) (Satellite Box) (LD) (Receiver) (CD Player)

(VCR)

Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*

--- --- ---

•

x Skip FWD

• Skip REW

--- ---

Rewind --- --- Rewind Pause --- --- Pause Play --- --- Play

Slow FWD Slow REW --- ---

Skip FWD Skip REW Skip REW

--- ---

---

Skip FWD

Rewind Rewind Rewind Pause Pause Pause Play Play Play

Slow FWD Slow FWD

--- ---

Fast FWD --- --- Fast FWD --- Fast FWD Fast FWD Fast FWD

--- ---

TV/SAT --- --- --- TV/VCR Reverse

--- --- --- Disc shift AM/FM Disc shift --- Replay Stop

--- ---

Stop --- Stop Stop Stop

REC Menu --- --- --- --- --- Record Record (Single Click)

LIST

--- --- --- --- --- --- ---

(Double Click) (Double Click)

FAV channel --- --- --- --- --- --- --up/down

HOME --- --- --- --- --- --- --Split

TV TV TV TV TV TV TV PIC MODE TV TV TV TV TV TV TV FAV SCAN --- --- --- --- --- --- --Freeze

TV TV TV TV TV TV TV

(PVR)

Notes:

--- = key does not send a signal in that remote control device mode.

————

TV = key will affect the TV, even when the remote control is not in the “TV” device mode.

* 1The backlight key is a toggle key and does not send an IR signal.

By default

operate the TV’s volume, even when “TV” is not the current device mode. (This includes all remote control device modes except AUDIO 1 and AUDIO 2).

If you unlock the remote control’s volume keys

will operate the volume of the device associated with the current device mode. (This includes all remote control device modes.)

If you lock the remote control’s volume keys to a specific device mode

the locked mode, even when the locked mode is not the current device mode. (This includes all device modes except AUDIO 1 and AUDIO 2).

When the remote control is in AUDIO1 (or AUDIO 2) mode

(or AUDIO 2) mode, even when the volume is locked to another mode.

See “Using the remote control MODE button to control your other devices” on page 33 and “Using the volume lock feature” on page 37.

(factory setting), the remote control’s volume keys (VOL yz and MUTE) are “locked” to the “TV” device mode. The remote control will

, each device mode will have its own volume (if the device ID has volume data). The remote control

, the remote control will operate the volume of the device associated with

, the remote control will operate the volume of the device associated with the AUDIO 1

Page 36

Chapter 3: Using the remote control

Programming the remote control to operate your other devices

Device code setup

1. Find the code for your device brand in the remote control device code table on pages 38–39.

If more than one code is listed, try each one separately until you find one that works.

2. Press MODE until the mode indicator for the device (CBL/SAT, VCR/PVR, DVD, AUDIO 1, or AUDIO 2) lights up.

3. While holding down the RECALL button, press the Number buttons to enter the four-digit code for your device.

• If a valid code is entered, the mode indicator will blink

two times.

• If an invalid code is entered, the mode indicator will blink

one long blink.

4. Point the remote control at the device and press POWER to test the code.

• If the device responds to the remote control, you have

entered the correct code.

• If the device does not respond to the remote control,

repeat steps 3 and 4 using another code.

Note: After programming the remote control, make sure all necessary keys on the TV remote control (in addition to POWER) operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

5. To control the TV, repeatedly press MODE to select “TV.”

Note:

• Although the TV remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you want to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s original remote control (or the control buttons on the device).

• Every time you change the batteries you will need to reprogram the remote control.

• Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1. Press MODE to select the mode you want to set up.

2. While holding down RECALL, press 8, 5, 0, 0. The remote control will enter program mode.

3. Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4. If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink two times and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press y, and then press POWER. Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds during programming, the remote control will exit the program mode and return to the previous code.

POWER

Numbers

MODE

CH y

VOL y

RECALL

Page 37

Chapter 3: Using the remote control

Programming the remote control to operate your other devices (continued)

Using the volume lock feature (8000)

By default (factory setting), the remote control’s volume keys (VOL yz and MUTE) are locked to the “TV” device mode. The remote control will operate the TV’s volume, even when “TV” is not the current device mode. (This includes all remote control device modes except AUDIO 1 and AUDIO 2).

If you unlock the remote control’s volume keys, each device mode will have its own volume (if the device ID has volume data). The remote control will operate the volume of the device associated with the current device mode. (This includes all remote control device modes.)

If you lock the remote control’s volume keys to a specific device mode, the remote control will operate the volume of the device associated with the locked mode, even when the locked mode is not the current device mode. (This includes all device modes except AUDIO 1 and AUDIO 2).

When the remote control is in AUDIO1 (or AUDIO 2) mode, the remote control will operate the volume of the device associated with the AUDIO 1 (or AUDIO 2) mode, even when the volume is locked to another mode.

See “Using the remote control MODE button to control your other devices” on page 33.

To lock the remote control’s volume keys to a specific mode (CBL/SAT in this example):

1. Repeatedly press MODE to select CBL/SAT mode.

2. While holding down the RECALL button, press 8, 0, 0, 0.

3. Press VOL y.The CBL/SAT mode indicator will blink two

times (locked). The remote control’s volume keys will now operate the

volume of the device associated with the CBL/SAT mode, even when CBL/SAT is not the current device mode (for all device modes except AUDIO 1 and AUDIO 2).

Operational feature reset (8900)

This feature clears all programmed remote control features not related to “Device code setup” and resets the volume lock to the “TV” device mode.

To reset the remote control:

While holding down the RECALL button, press 8, 9, 0, 0. The mode indicator will blink two times, pause, and then blink two more times.

Numbers

MODE

VOL yz

RECALL

To unlock the remote control’s volume keys:

1. While holding down RECALL, press 8, 0, 0, 0.

2. Press VOL z. The CBL/SAT mode indicator will blink four

times (unlocked).

Page 38

Chapter 3: Using the remote control

Multi-brand remote control device codes

VCRs/PVRs

Brand Code

ADMIRAL 0135 AIWA 0127, 0132, 0181 AKAI 0129, 0114, 0115,

0116 AUDIO DYNAMIC 0139, 0111 BELL&HOWELL 0105, 0113 BROKSONIC 0120, 0126, 0180 CANON 0123, 0125 CCE 0143 CITIZEN 0106 CRAIG 0105, 0129, 0106 CURTIS MATHES 0145, 0124, 0127 DAEWOO 0143, 0101, 0124,

0175 DBX 0139, 0110, 0111 DIMENSIA 0145 EMERSON 0143, 0126, 0119,

0103, 0125, 0142,

0120, 0118 FISHER 0105, 0108, 0109,

0107, 0113, 0165 FUNAI 0127, 0126, 0120,

0134 GE 0133, 0145, 0124 GO VIDEO 0137, 0151, 0163,

0149, 0150, 0182 GOLDSTAR 0106 GRADIENTE 0170, 0171, 0168,

0134, 0156 HITACHI 0123, 0145, 0100,

0127, 0168 INSTANT REPLAY 0124, 0123 JENSEN 0139 JVC 0139, 0110, 0111,

0134, 0157, 0158,

0184, 0185, 7104 KENWOOD 0139, 0110, 0106,

0111 LG 0159 LXI 0127, 0106, 0100,

0107, 0108, 0105,

0109 MAGNAVOX 0131, 0123, 0124,

0173 MARANTZ 0139, 0110, 0111 MARTA 0106 MEMOREX 0124, 0109 MGA 0138, 0140, 0147,

0148, 0141, 0142 MINOLTA 0100, 0145 MITSUBISHI 0138, 0140, 0147,

0148, 0141, 0142,

0161, 0164 MULTITECH 0147, 0127, 0104 NEC 0139, 0110, 0111,

0134 OLYMPIC 0124, 0123 OPTIMUS 0128, 0121, 0135,

0106 ORION 0126, 0120, 0132 PANASONIC 0123, 0124, 0121,

0122 PENNEY 0124, 0100, 0145,

0105, 0139, 0110,

0111 PENTAX 0100, 0111, 0145

VCRs/PVRs (cont.)

Brand Code

PHILCO 0131, 0124, 0127,

0123, 0126, 0120, 0143

PHILIPS 0131, 0123, 0124,

0173 PIONEER 0123 PROSCAN 0145, 0100, 0123,

0124, 0131, 0146,

0101, 0102, 0133 QUASAR 0121, 0122, 0123,

0124 RADIO SHACK 0133, 0124, 0105,

0136, 0109, 0140,

0127 RCA 0133, 0145, 0100,

0123, 0124, 0131,

0146, 0101, 0102,

0170, 0172, 0174,

0176, 0183 REALISTIC 0124, 0105, 0136,

0109, 0140, 0127 Replay TV 7102 SAMSUNG 0137, 0102, 0104,

0133 SAMTRON 0163 SANSUI 0139, 0126, 0120,

0152 SANYO 0105, 0109, 0113 SCOTT 0101, 0102, 0104,

0109, 0138, 0140,

0147, 0148, 0126 SEARS 0105, 0106, 0107,

0108, 0100 SHARP 0135, 0136, 0167,

0162 SHINTOM 0117 SIGNATURE 2000 0127, 0135 SINGER 0117 SONY 0128, 0129, 0130,

0153, 0154, 0155,

7101 SV2000 0127 SYLVANIA 0131, 0123, 0124,

0127, 0178 SYMPHONIC 0127, 0168, 0177 TASHIRO 0106 TATUNG 0139, 0110, 0111 TEAC 0139, 0110, 0127,

0111 TECHNICS 0121, 0122, 0123,

0124 TEKNICA 0124, 0127, 0112 THOMSON 0179, 0183 Tivo 7100, 7101 TOSHIBA 0101, 0146, 0166,

0160 VECTOR RESEARCH 0111 WARDS 0135, 0136, 0109,

0144, 0106 YAMAHA 0105, 0139, 0110,

0111 ZENITH 0144, 0106, 0169,

0180

Cable boxes

Brand Code

ABC 1124 ARCHER 1132, 1125 CABLEVIEW 1105, 1132 CITIZEN 1122, 1105 CURTIS 1112, 1113 DIAMOND 1124, 1132, 1125 EAGLE 1129 EASTERN 1134 GCBRAND 1132, 1105 GEMINI 1122, 1143 G.I. (GENERAL 1119, 1124, 1125,

INSTRUMENT) 1126, 1127, 1120,

1121, 1122, 1111, 1123, 1152

HAMLIN 1140, 1141, 1142,

1145, 1118, 1112 HITACHI 1103, 1124 JERROLD 1119, 1124, 1125,

1126, 1127, 1120,

1121, 1122, 1111,

1123, 1152 MACOM 1103, 1104, 1105,

1108 MAGNAVOX 1133 MEMOREX 1130 MOTOROLA 1119, 1124, 1125,

1126, 1127, 1120,

1121, 1122, 1111,

1123, 1152 MOVIETIME 1132, 1105 OAK 1139, 1137, 1102 PANASONIC 1109, 1110, 1114,

1151, 1153 PHILIPS 1128, 1129, 1130,

1106, 1107, 1150,

1131 PIONEER 1101, 1116 PULSAR 1105, 1132 PUSER 1132 RCA 1115 REALISTIC 1132 REGAL 1112, 1118, 1140,

1141, 1142, 1145,

1149 REGENCY 1134 REMBRANT 1137, 1132, 1105,

1138 SAMSUNG 1105 SCIENTIFIC 1111, 1112, 1113

AMERICAN SLMARK 1105, 1101 SPRUCER 1105, 1110 STARGATE 1132, 1105 TELECAPTION 1148 TELEVIEW 1101, 1105 TEXSCAN 1144 TOCOM 1135, 1136, 1147 TOSHIBA 1104, 1146 UNIKA 1132, 1125 UNIVERSAL 1122, 1132 VIDEOWAY 1106 VIEWSTAR 1129, 1130 ZENITH 1117, 1100 ZENITH/DRAKE 1100 SATELLITE

Page 39

Chapter 3: Using the remote control

Multi-brand remote control device codes (continued)

CD players

Brand Code

ADMIRAL 6126 AIWA 6133, 6135 CARVER 6129 DENON 6142, 6151 EMERSON 6139 FISHER 6105, 6106 GARRARD 6117 HARMAN/KARDON 6120, 6121, 6123,

6119 HITACHI 6107 JENSEN 6134 JVC 6140, 6141, 6145,

6148, 6151 KENWOOD 6100, 6101, 6111,

6145 LXI 6136 MAGNAVOX 6129, 6132 MARANTZ 6129 MACINTOSH 6121 NAKAMICHI 6110 ONKYO 6114, 6115 OPTIMUS 6108, 6118, 6120,

6122 PANASONIC 6124, 6125, 6127,

6150 PHILIPS 6129, 6130, 6149 PIONEER 6108 QUASAR 6125, 6127, 6124 RCA 6147, 6137, 6138,

6131, 6152 SANSUI 6110, 6146, 6113 SANYO 6105 SCOTT 6110, 6146 SHARP 6142, 6143 SHERWOOD 6120 SONY 6128 SOUNDE-SIGH 6144 TEAC 6112, 6116, 6118 TECHNICS 6127, 6124, 6125 VICTOR 6140, 6141, 6145 YAMAHA 6102, 6103, 6104

Receivers

Brand Code

ADMIRAL 4120 AIWA 4125, 4126, 4146 DENON 4134, 4135, 4136,

4143 FISHER 4104 GARRARD 4113 HARMAN KARDON 4115, 4123, 4145 JENSEN 4129 JVC 4132, 4133, 4140,

4144 KENWOOD 4100, 4108, 4141,

4142, 4147 MAGNAVOX 4127, 4128 MARANTZ 4124 MCNTOSH 4116 MITSUBISHI 4148 NAKAMICHI 4106, 4117 ONKYO 4109, 4114 OPTIMUS 4103, 4127, 4131,

4130 PANASONIC 4119, 4118, 4121 PHILIPS 4123

Receivers (cont.)

Brand Code

PIONEER 4105, 4107, 4150 QUASAR 4119, 4118, 4121 RCA 4103, 4105, 4127,

4131, 4130, 4149 SANSUI 4103, 4111, 4139 SHARP 4134, 4137 SONY 4122 SOUNDE-SIGH 4138 TEAC 4112, 4113, 4111,

4110 TECHNICS 4121, 4118, 4119 VICTOR 4132, 4133 YAMAHA 4101, 4102

Laser disks

Brand Code

DENON 5114 HITACHI 5100 KENWOOD 5102, 5103 MAGNAVOX 5101 MARANTZ 5114 MITSUBISHI 5114, 5118, 5119 NEC 5114 PANASONIC 5104, 5105, 5106,

5115 PHILIPS 5111 PIONEER 5114 PROSCAN 5114 QUASAR 5104, 5105, 5106,

5115 RCA 5114 SAMSUNG 5112 SANYO 5114, 5117 SHARP 5113, 5116 SONY 5107, 5108, 5109,

5110 TEAC 5114 TOSHIBA 5114 YAMAHA 5101

DVD players

Brand Code

AIWA 3123 APEX 3120 DENON 3100, 3117 FERGUSON 3101 HITACHI 3111 JVC 3109 KENWOOD 3115, 3129 KONKA 3119 MITSUBISHI 3105 NORDMENDE 3101 ONKYO 3121 ORITRON 3124 PANASONIC 3100 PHILIPS 3103, 3116 PIONEER 3102 RAITE 3113 RCA 3101, 3106 SABA 3101 SAMPO 3114 SAMSUNG 3110 SHARP 3108 SYLVANIA 3132, 3118 SMC 3125 SONY 3104, 3126, 3127,

3128 TECHNICS 3100 THOMSON 3101 TOSHIBA 3103 WAVE 3122 YAMAHA 3100, 3130 ZENITH 3107, 3112 VIALTA 3131 FUNAI 3132, 3118

Satellite receivers

Brand Code

DISH NETWORK 2105, 2115, 2116, (Echostar) 2117 ECHOSTAR 2105 EXPRESS VU 2105, 2115 G.E. 2106 G.I.(GENERAL 2108 INSTRUMENT) GRADIENTE 2114 HITACHI 2103, 2111, 2112 HNS(Hughes) 2103 MAGNAVOX 2101, 2102 PANASONIC 2104 PHILIPS 2101, 2102, 2118 PRIMESTAR 2108 PROSCAN 2106, 2109, 2110,

2113 RCA 2106, 2109, 2110,

2113 SONY 2107 STAR CHOICE 2103, 2108 TOSHIBA 2100, 2103, 2119,

2120, 2121, 2122,

2123, 2124, 2125 UNIDEN 2101, 2102

Page 40

Menu layout and navigation

The illustrations below and on the next page provide a quick overview of your TV’s menu system.

Main menu layout

To open the main menus (illustrated below), press MENU on the remote control or TV front panel.

➞ TV Guide On Screen ➞ Audio Player ➞ Launches the MP3 Audio Player

Applications ➞ Picture Viewer ➞ Launches the JPEG Picture Viewer

➞ Digital CC / Audio Selector ➞ Launches the ATSC Digital CC Selector ➞ CableCARD™ ➞ Dynamic list of items provided by inserted CableCARD™.

➞ Picture Settings ➞ [ Picture Settings edit window ]

Video ➞ Advanced Picture Settings ➞ [ Advanced Picture Settings edit window ]

➞ Theater Settings ➞ [ Theater Settings edit window ]

➞ Audio Settings ➞ [ Audio Settings window ]

Audio ➞ Advanced Audio Settings ➞ [ Advanced Audio Settings window ]

➞ Audio Setup ➞ [ Audio Setup window ]

➞ Favorite Channels ➞ [ Favorite Channels edit window ]

Preferences ➞ Closed Caption Mode ➞ Off / CC1 / CC2 / CC3 / CC4 / T1 / T2 / T3 / T4

➞ Closed Caption Advanced ➞ [ Advanced Closed Captions window ] ➞ Input Labeling ➞ [ Input Labeling edit window ] ➞ Menu Language ➞ English / Français / Español ➞ Home CH Setup ➞ [ Home Channel Setup window ]

➞ Opens the TV Guide On Screen® system

(This option is not available if a CableCARD™ is not inserted.)

➞ Enable Rating Blocking ➞ Off / On

Locks ➞ Edit Rating Limits ➞ [ Edit Rating Limits edit window ]

➞ Channels Block ➞ [ Channels Block edit window ] ➞ Input Lock ➞ Off / Video / Video+ ➞ Front Panel Lock ➞ Off / On ➞ GameTimer™ ➞ Off / 30 Min / 60 Min / 90 Min / 120 Min ➞ New PIN Code ➞ [ New PI N Code entry window ]

Setup

➞ Installation ➞ [Opens the Installation menu (see page 41 for details) ] ➞ Sleep Timer ➞ [ Sleep Timer edit window ] ➞ On/Off Timer ➞ [ On/Off Timer window ]

➞ PC Settings ➞ [ PC Settings edit window ]

➞ HDMI 1 Audio ➞ Auto / Digital / Analog

➞ HDMI 2 Audio ➞ Auto / Digital / Analog ➞ Slide Show Interval ➞ 2 sec. / 5 sec. / 10 sec. / 15 sec. / 20 sec. ➞ AVHD Skip Time ➞ 1 min. / 3 min. / 5 min. / 15 min. ➞ Gray Level ➞ 1 / 2 / 3 ➞ Quick Restart ➞ Off / On

Applications

TV Guide On Screen

Audio Player

Picture Viewer

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTN

EXIT

Note: The menu backgrounds may sometimes appear black, depending on the signal being received.

Page 41

Chapter 4: Menu layout and navigation

Setup/Installation menu layout

To open the Installation menu (illustrated below), press MENU on the remote control or TV front panel, open the Setup menu, select Installation, and press ENTER.

Press MENU. Open the Setup menu, and then open the Installation sub-menu – –

➔

Terrestrial ➞ Channel Program ➞ ANT1

➞ Input Configuration ➞ [ Input Configuration window ]

➞ [ Scans for new channels on selected Antenna ]

➞ ANT2

➞ Channel Add/Delete ➞ [ Channel Add/Delete window ] ➞ Signal Meter ➞ [ Signal Meter window ]

}

Devices

Network ➞ E-mail Scheduling Setup

TV Guide On Screen® Setup ➞ Start ➞ [ Launches the TV Guide On Screen® system setup ]

Time and Date ➞ Start Setup ➞ [ Opens the Time and Date Setup window ]

System Status ➞ System Information ➞ [ Opens the System Information window ]

Navigating the menu system

You can use the buttons on the remote control or TV front touchpad to access and navigate your TV’s on-screen menu system.

• Press MENU to open the menu system.

• When a menu is open, use the up/down/left/right arrow buttons (yzx •) on the remote control or TV front panel to move in the corresponding direction in the menu.

• Press ENTER to save your menu settings or select a highlighted item. (A highlighted menu item appears in a different color in the menu.)

• All menus close automatically if you do not make a selection within 60 seconds, except the signal meter menu, which closes automatically after 5 minutes.

• To close a menu instantly, press EXIT.

TV front panel touchpad

EXIT

* The MENU button on the TV front panel touchpad

functions as the ENTER button when a menu is on-screen.

➞ IEE E1394 Devices ➞ [ IEEE1394 Device Management window ] ➞ TheaterNet Devices ➞ [ TheaterNet Setup window ]

➞ Basic Network Setup

➞ Home File Server Setup

Remote control

zyx

•

(ENTER*)

ENTER

x •

EXIT

Page 42

TV Guide On Screen® setup

Setting up the TV Guide On Screen® system

The TV Guide On Screen® system in this TV is a no-fee interactive program guide that uses the information you enter during the following setup process to provide you with a channel lineup and program listings for your area. The listings are automatically updated several times a day.

Note:

• You must first set up your TV according to the applicable

connection instructions in Chapter 2.

• If you connected a Toshiba Symbio™ AVHD Recorder, you must perform the following TV Guide On Screen

system setup in order to use the Symbio’s full functionality. See pages 26 and 55 for further details about AVHD digital recorders.

To set up the TV Guide On Screen® system:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

3. A new set of Installation menu icons appears on-screen (see

TV Guide On Screen Setup

Start

illustration at right). Open the TV Guide On Screen menu, highlight Start,

Setup

Navigate

Select

Back Exit

CH RTN

EXIT

and press ENTER.

Configuring the location of your TV

Screen 1: Select the TV location (USA or Canada), and then

press ENTER.

Screen 2: Enter the ZIP code (U.S.A.) or postal code (Canada)

for your location (use the Number buttons on the remote control for numbers and the yz buttons for letters), and then press ENTER. Screen 3 appears.

Screen 3: Do you have Cable service connected?

If you select Yes (and press ENTER), screen 4 appears. If you select No (and press ENTER), screen 12 appears.

4. The following screen appears. Highlight “Set up TV Guide On Screen

now” and press ENTER to continue.

5. The following screen appears. Press ENTER to continue.

Screen 4: Do you have a Cable box connected?

If you select Yes (and press ENTER), screen 5 appears. If you select No (and press ENTER), screen 13 appears.

Page 43

Chapter 5: TV Guide On Screen® setup

Setting up the TV Guide On Screen® system (continued)

Screen 5: Which TV input is your cable box plugged into?

If you select ANT 1, screen 6 appears. If you select Video 1, screen 7 appears.

Screen 6: Select the channel your TV is tuned to when using

your cable box, and then press ENTER. Screen 7 appears.

Screen 7: The on-screen diagram shows the correct way to

connect your Cable box to the G-LINK TV. Make sure the G-LINK

cable is installed properly.

terminal on the

For additional details, see page 28.

Press ENTER to display screen 8.

Screen 9: To allow the TV Guide On Screen® system to find the

correct code for your brand of Cable box, tune your Cable box to channel 02, leave the Cable box and TV ON, and then press ENTER. Screen 10 appears.

Screen 10: The TV Guide On Screen® system will test the code

for the brand of Cable box you selected. Do not press any keys on the TV, remote control, or Cable box until the testing process is completed. When testing is completed, screen 11 appears.

Screen 11: If your Cable box tuned itself to channel 09 after

testing, select Yes and press ENTER. If you selected ANT 1 in screen 5, screen 13 appears. If you selected Video 1 in screen 5, screen 12 appears.

Screen 8: Highlight your Cable box brand, and then press

ENTER to display screen 9.

If your Cable box did not tune itself to channel 09 after testing and you want to test the same code again, select “Test this code again” and press ENTER.

If you want to test a different code, select No and press ENTER. Screen 10 appears.

Note: Many cable boxes require testing more than one code.

(Continued on next page)

Page 44

Chapter 5: TV Guide On Screen® setup

Setting up the TV Guide On Screen® system (continued)

Screen 12: Do you have an antenna connected?

Select either Yes or No, and then press ENTER. Screen 13 appears.

Note: If you selected No in screen 3, you must select Yes in this screen to receive a channel lineup and program listings.

Screen 13: Are the settings correct?

If you select Yes, screen 14 appears. If you select No, screen 1 appears.

Screen 16: The on-screen diagram shows the correct way to

connect your VCR to the G-LINK

Make sure the G-LINK

cable is installed properly. For

terminal on the TV.

additional details, see page 28.

Press ENTER to display screen 17.

Screen 17: Select your VCR brand, and then press ENTER.

Screen 18 appears.

Screen 14: Congratulations! You have completed basic

TV Guide On Screen

Note: Read the on-screen information regarding the amount of time it may take for listing information to download from the TV Guide On Screen® service. Also see “TV Guide On Screen® Reminder” on page 45.

system setup.

Press ENTER to display screen 15.

Screen 15: Is a VCR connected?

If you select Yes, screen 16 appears. If you select No, screen 21 appears.

Screen 18: Turn on your VCR, insert a tape (either blank or

previously recorded), and then press PLAY. Screen 19 appears.

Screen 19: The TV Guide On Screen® system will test the code

for the brand of VCR you selected. Do not press any keys on the TV, remote control, or VCR until the testing process is completed. When testing is completed, screen 20 appears.

Page 45

Chapter 5: TV Guide On Screen® setup

Setting up the TV Guide On Screen® system (continued)

Screen 20: If your VCR stopped playing the tape after testing,

select Yes and press ENTER. Screen 21 appears. If your VCR did not

stop playing the tape after testing and you

Did your VCR stop playing?

want to test the same code again, select “Test this code again” and press ENTER.

If you want to test a different code, select No and press ENTER. Screen 19 appears.

Note: Many VCRs require testing more than one code.

Screen 21: Review the setup information displayed on your TV

screen (an example is shown below). If the information on

your TV screen is correct for your setup, select “Yes, end setup” and press ENTER. Screen 22 appears.

If the information is incorrect, select “No, repeat setup process” and press ENTER. Screen 1 appears.

Screen 22: Congratulations! You have successfully completed

TV Guide On Screen

system setup.

Press ENTER to display screen 23.

Screen 23: This screen provides helpful information on using

your TV Guide On Screen

system.

Press ENTER to exit the TV Guide

On Screen

setup and

watch TV.

TV Guide On Screen® Reminder

The TV Guide On Screen® system receives program listing data through your Cable or over-the-air video signal. In order to receive regular program listing updates, remember to do the following:

1. Leave the TV in standby mode when it is not in use by turning it OFF but leaving the power cord plugged in.

2. If you have a Cable box connected, leave it ON.

3. If you have a VCR connected, turn it OFF when not in use (but do not unplug the power cord). See pages 15–16 for VCR connection instructions.

4. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, follow the on-screen instructions.

Note: If the TV power cord is unplugged for an extended period of time, it may take up to 24 hours with the TV in standby mode (power cord plugged in and power OFF) to download the TV Guide On Screen program schedule. It may take up to 7 days before an entire program schedule is available.

Turning off the TV Guide On Screen

automatic display feature

After you set up the TV Guide On Screen® system, the program guide will display automatically (by default) when you turn on the TV.

To turn off the automatic program guide:

1. Press TV GUIDE on the remote control to open the TV Guide On Screen

2. Use the x • buttons to select the Setup menu.

3. Use the yz buttons to select “Change Default Options,” and then press ENTER.

4. Use the yz buttons to select “General Defaults,” and then press ENTER.

5. Set the “Auto Guide” option to Off.

6. Use the yz buttons to select Done, and then press ENTER.

system (if it is not already open).

Page 46

Setting up your TV

For menu navigation instructions, see Chapter 4.

Selecting the menu language

You can choose from three different languages (English, French and Spanish) for the on-screen display of menus and messages.

Note: The TV Guide On Screen® menus are in English, regardless of the language selected in this menu.

To select the menu language:

1. Press MENU and open the Preferences menu.

2. Highlight Menu Language and press •.

3. Press y or z to select your preferred menu language and

press ENTER.

Preferences

Favorite Channels

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language English

Home CH Setup

Navigate

Select

4. Press EXIT to close the Preferences menu.

Off

Back Exit

CH RTN

English

Français

Español

EXIT

Configuring the antenna input sources for the ANT 1 and ANT 2 terminals

To configure the ANT 1 and ANT 2 input sources:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3 below.)

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

3. Open the Terrestrial menu, highlight Input Configuration, and press ENTER.

Note: The Terrestrial menu may not be accessible (items will be “grayed out”) in some instances (for example, if a cable box is connected to the ANT 1 input or if one of the VIDEO modes is the current input during TV Guide On Screen® setup).

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Navigate

Select

Back Exit

CH RTN

EXIT

4. Press x or • to select the input source (Cable or Antenna) for the ANT 1 input on the TV.

Note: If a cable box is connected to the ANT 1 input during TV Guide On Screen® setup, the entire Terrestrial menu will not be accessible, including the input source for ANT 1, which will automatically display “Cable Box.”

5. Press z and then x or • to select the input source (Cable or Antenna) for the ANT 2 input on the TV, if applicable. If you have not connected anything to the ANT 2 input, skip this step.

Input Configuration

Antenna 1 In

Antenna 2 In

Cancel

Antenna

Done

Cable

6. To save your new settings, highlight Done and press ENTER. To revert to your original settings, highlight Cancel and press ENTER.

Page 47

Chapter 6: Setting up your TV

Programming channels into the TV’s channel memory

When you press CHANNEL y or z on the remote control or TV front panel, your TV will stop only on the channels you program into the TV’s channel memory.

Follow the steps below to program channels into the TV’s channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels.

Note:

• You must configure the antenna input sources before programming channels (see page 46).

• If the input signal type is set to CABLE for an antenna input, the automatic channel programming process erases channels that were previously programmed into the TV’s memory.

• If the input signal type is set to ANTENNA, the automatic channel programming process does NOT erase channels that were previously programmed into the TV’s memory, but adds newly found channels to the existing set of programmed channels. To remove a channel from the memory, you must manually delete it (see next page).

• To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

• Programming channels for an antenna input configured for CABLE will take substantially longer than for an antenna input configured for ANTENNA. This is normal; however, once channel programming is completed, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.

• If you have a CableCARD™ inserted (page 14), channel programming for ANT 1 is disabled because the CableCARD™ automatically loads the Cable channel list into the TV’s channel memory.

4. Open the Terrestrial menu, highlight Channel Program, and press ENTER.

5. Highlight ANT 1 or ANT 2, depending on which antenna input you want to program channels for, and then

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

press ENTER to start automatic channel programming.

Navigate

ANT 1 Antenna Scanning channels, please wait ...

Select

Abort

Back Exit

CH RTN

EXIT

The TV will automatically cycle through all the channels for the antenna input you selected, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above).

6. To cancel channel programming, either press EXIT or highlight Abort in the on-screen display and press ENTER.

When channel programming is done, press CHANNEL y or z to view the programmed channels.

Channel Numbers

52%

To program channels automatically:

1. Make sure you have configured the antenna input sources. See page 46 for details.

2. Press MENU and open the Setup menu.

3. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen).

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

CHANNEL yz

TV front panel touchpad

CHANNEL z / y

MENU (ENTER)

Page 48

Chapter 6: Setting up your TV

Programming channels into the TV’s channel memory (continued)

Manually adding and deleting channels in the channel memory

After automatically programming channels into the channel memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3).

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

3. Open the Terrestrial menu, highlight Channel Add/Delete, and then press ENTER.

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Navigate

4. The illustration below left shows channels programmed for the ANT 1 antenna input. To view the list of channels programmed for the ANT 2 or Cable box antenna input, press the y z buttons to highlight either “ANT 2” or “Cable Box” and press ENTER.

Note: “Cable Box” will appear only if you connected a cable box to your TV.

Channel Add/Delete

2 - 1

2 - 2

7 - 1

2 Sec

Select

Analog ANT 1

Digital

Analog

Digital

Analog

Auto

Back Exit

CH RTN

Back Exit

CH RTN

EXIT

ANT 2

Cable Box

Reset

Cancel

Done

ANT 1

Channel Add/Delete

Cable Box

Analog ANT 1

ANT 2

Analog

Cable Box

Analog

Reset

Analog

Cancel

Analog

Done

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you want to add, and then press ENTER to check the box.

To manually add digital subchannels on a physical channel:

Use the Channel Numbers and the Dash (–/100) on the remote control to enter the channel number (for example, 56–1).

If the channel is found, the number will be added to the list and the box will be checked.

If the channel is not found, a message will appear.

To remove a channel from the channel memory:

Highlight the checked box next to the channel number you want to remove, and then press ENTER to uncheck the box.

To save your new settings:

Highlight Done and press ENTER.

To revert to your original settings:

Highlight Cancel and press ENTER before saving.

To remove all channels from the channel memory:

Highlight Reset and press ENTER, and then highlight Done and press ENTER.

Note:

• This action applies to the current antenna input only. To delete/add channels on the other input, highlight the input you want (ANT1, ANT 2, or Cable Box) and press ENTER.

• This action cannot be cancelled unless you highlight Cancel and press ENTER before saving your changes.

Channel Add/Delete

2 - 1

2 - 2

7 - 1

Analog ANT 1

Digital

Analog

Digital

Analog

Digital

Analog

ANT 1

ANT 2

Cable Box

Reset

Cancel

Done

Page 49

Chapter 6: Setting up your TV

Programming your favorite channels

You can program up to 27 channels as favorite channels into three Favorite Channel sets (nine channels from the ANT 1 input, nine from the ANT 2 input, and nine from the Cable box input). You can then scan through your favorite channels only, skipping other channels you do not normally watch.

To add and delete channels in the Favorite Channels sets:

1. Press MENU and open the Preferences menu.

2. Highlight Favorite Channels and press ENTER.

3. Use the yz buttons to select either ANT 1, ANT 2, or

Cable Box and press ENTER.

4. Highlight Edit and press ENTER.

Note: “Cable Box” will appear only if you connected a cable box to your TV.

Preferences

Favorite Channels

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language English

Home CH Setup

Navigate

Select

Off

Back Exit

CH RTN

EXIT

Favorite Channels ANT 1

Empty Empty Empty

ANT 1

ANT 2

Cable Box

Edit

Done

To add a channel to the selected Favorite Channel set:

Use the

buttons to highlight an unchecked box next to a channel you want to set as a favorite, and then press ENTER to check the box.

Edit Favorite Channels

To delete the channel from the selected Favorite Channel set:

Highlight a checked box and press ENTER to uncheck it.

Note: If you try to add more than nine favorite channels per

Only 9 favorite channels are allowed,

please deselect other channels first.

input, an error message will appear. You will need to delete (uncheck) a channel before you can add another.

Reset

Cancel

Done

ANT 1

When done, highlight Done and press ENTER.

To clear your favorite channel lists:

1. Press MENU and open the Preferences menu.

2. Highlight Favorite Channels and press ENTER.

3. Highlight Edit and press ENTER.

4. Highlight Reset and press ENTER.

5. Highlight Done and press ENTER.

Edit Favorite Channels

2 - 1

2 - 2

4 - 1

17 - 1

17 - 2

28 - 1

28 - 2

28 - 3

Reset

Cancel

Done

ANT 2

To tune your favorite channels for the current ANT input:

Press FAV CH yz.

To tune your favorite channels using the favorite channel list:

1. Press 100 to display the favorite channel list.

2. Press the corresponding number button (1–9) to select your desired channel.

Note: To tune your favorite channels for another input, press INPUT to select the other input.

To quickly scan through your favorite

5 6

7 8

CH 4-1

CH 4-2

CH 9

CH 10

CH 12

CH 17

CH 19

---

channels in a nine picture multi-window (for the current ANT input):

Press FAV SCAN. See page 83 for details.

Note:

• To tune to a channel from the FAV SCAN mode, highlight a

window and press ENTER.

• To scan your favorite channels for another input, press INPUT to

select the other input.

Channel Numbers

100

To program favorite channels for another input:

Either... Highlight ANT 1, ANT 2, or Cable Box, which

will change the favorite channel settings in the selected input. (This will not change the TV’s current input.)

Or... Press INPUT to select ANT 1, ANT 2, or Cable

Box and then repeat steps 1–4, above.

Favorite Channels ANT 2

CH 6 Empty Empty

Empty Empty Empty

ANT 1

ANT 2

Cable Box

Edit

Done

x •

FAV CH yz

FAV SCA N

Page 50

Chapter 6: Setting up your TV

Setting up and using TheaterNet™ on-screen device control

The TheaterNet feature allows you to control many brands of IEEE1394 and/or infrared remote-controlled A/V devices through your TV using on-screen control icons and the TV’s remote control.

Note:

• Although the TheaterNet on-screen device control feature includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TheaterNet feature to operate your device or some of the features on that device, use the device’s remote control or the controls on the device.

• For IR pass-through device control information, see “Connecting a device to the TheaterNet OUT infrared terminal” on page 22.

Setting up TheaterNet

All device types except IEEE1394 require the following setup process before you can control them using the TheaterNet on-screen icons.

All compatible IEEE1394 devices are automatically recognized by the TheaterNet feature and do not require setup.

Note: See page 25 for details about the IEEE1394 ports. If your IEEE1394 device is not recognized through the IEEE1394 port or through the TheaterNet feature, it may be possible to set it up for IR pass-through control as an infrared device (see page 22).

To set up TheaterNet device control:

1. Make sure you have properly connected your infrared remote-controlled device(s). See pages 22 and 25 for details.

2. Press MENU and open the Setup menu.

3. Highlight Installation and press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

5. The TheaterNet Setup menu opens.

TheaterNet Setup

Input

Type

Brand

IR List

IR Code

Video 1

Cable

General Instrum...

0000

Reset Done

Test

Select device type, brand, and IR code from owners manual.

Using the x • buttons, select the Input the device is connected to.

Note: When the input is changed, all unsaved settings will be lost.

6. Press z and then x • to select the device Type.

7. Press z and then x • to select the device Brand.

Note: When selecting a new brand, the IR code will be set to 0.

8. Press z and then x • to select the device’s IR List.

9. If the desired IR code is found, skip to step 10.

If the desired IR code is not in the list, press z and use the Channel Number buttons to enter the device IR code.

Note: You can find the IR code for your device in the on-screen list or in the TheaterNet device code table on pages 52–54.

10. Highlight Test and press ENTER to test whether the device responds to the code. If the device does not respond to the code, repeat steps 8 and 9 using another code for the same device.

When done, highlight Done and press ENTER or choose a different Input for which to set up TheaterNet device control.

To remove a device from TheaterNet:

1. Follow steps 1–5 above.

2. Highlight Reset and press ENTER.

4. A new set of Installation menu icons will appear on-screen, as shown below. Open the Devices menu, highlight TheaterNet Devices, and then press ENTER.

Devices

IEEE1394 Devices

TheaterNet Devices

Navigate

Select

Back Exit

CH RTN

EXIT

Page 51

Chapter 6: Setting up your TV

Setting up and using TheaterNet™ on-screen device control (continued)

Using the TheaterNet control icons

1. Set up your infrared devices in TheaterNet, if you have not already done so (see page 50).

Note: IEEE1394 devices do not need to be set up in TheaterNet because they appear automatically in the TheaterNet menu.

2. Press DEVICE on the remote control to display the device control selection screen.

DEVICE

CTRL

x •

ENTER

EXIT

3. Using the yzx • buttons, highlight the device you want to control and press ENTER.

TheaterNet

Video 2 Video 3

Toshiba

2 3

ColorStream HD1

Toshiba Toshiba

Toshiba

ColorStream HD2

The following are examples of the TheaterNet on-screen control icons for various devices.

Toshiba Symbio™ AVHD Recorder control*

* If you connected a Toshiba Symbio™ AVHD Recorder, you must

set up the TV Guide On Screen Symbio’s full functionality. See Chapter 5 for details on setting up the TV Guide On Screen details about AVHD digital recorders.

TheaterNet

Video 2 Video 3

Toshiba

2 3

ColorStream HD1

Toshiba Toshiba

Toshiba

ColorStream HD2

system in order to use the

system. See pages 26 and 55 for further

Toshiba

4. The input automatically changes to the input for the selected device, and the device’s control icons display on-screen.

Toshiba

TOP MENU

ColorStream HD1

SELECT

EXIT

ENTER

Highlight the icon for the function you want to control and press ENTER.

To select the device’s control icons directly:

Press CTRL.

To close the on-screen control icons:

Press EXIT.

To view another source:

Press DEVICE and select the input source you want to view.

Page 52

TheaterNet™ IR device codes

Chapter 6: Setting up your TV

Amplifiers

Brand Code

Aiwa 0406 Bose 0674 Carver 0269 Curtis Mathes 0300 Denon 0160 GE 0078 Harman/Kardon 0892 JVC 0331 Left Coast 0892 Linn 0269 Luxman 0165 Magnavox 0269 Marantz 0892, 0321, 0269 NEC 0264 Nakamichi 0321 Optimus 0395, 0300 Panasonic 0308, 0521 Parasound 0246 Philips 0892, 0269 Pioneer 0013, 0300 Polk Audio 0892, 0269 RCA 0300 Realistic 0395 Sansui 0321 Shure 0264 Sony 0689, 0220 Soundesign 0078, 0211 Technics 0308, 0521 Victor 0331 Wards 0078, 0013, 0211 Yamaha 0354, 0133

Cable boxes

Brand Code

ABC 0003, 0008, 0014,

0007, 0011, 0017 Americast 0899 Bell & Howell 0014 Bell South 0899 Contec 0019 Director 0476 Everquest 0015 Gemini 0015 General Instrument 0476, 0003, 0276,

0011, 0810 GoldStar 0144 Hamlin 0009, 0020, 0273 Hitachi 0011 Hytex 0007 Jasco 0015 Jerrold 0476, 0003, 0276,

0012, 0014, 0015,

0011, 0810 Memorex 0000 Motorola 0476, 1106, 0276,

0810 Oak 0019, 0007 Pace 0237 Panasonic 0000, 0107 Paragon 0000 Philips 0305, 0317 Pioneer 0877, 0144, 0533,

1877 Pulsar 0000 Quasar 0000

Cable boxes (cont.)

Brand Code

RadioShack 0015 Regal 0020, 0273, 0279 Rembrandt 0011 Runco 0000 Samsung 0144 Scientific Atlanta 0877, 0008, 0017,

0477, 1877 Signal 0015 Signature 0011 Sony 1006 Starcom 0003, 0015 Stargate 0015 Starquest 0015 Supercable 0276 Tocom 0012 Torx 0003 Toshiba 0000 Tusa 0015 United Artists 0007 Zenith 0000, 0525, 0899

CD players

Brand Code

Aiwa 0157, 0124 Burmester 0420 California Audio Labs 0029, 0303 Carver 0157, 0179, 0437 Classic 1297 DKK 0000 DMX Electronics 0157 Denon 0873, 0003 Emerson 0305 Fisher 0174, 0179, 1325 GPX 1296 Garrard 0393, 0420 Genexxa 0032, 0305 Harman/Kardon 0157, 0173 Hitachi 0032 JVC 0072, 1294 KLH 1318, 1372, 1373 Kenwood 0681, 0826, 0626,

0028, 0037, 0190 Koss 1317 Krell 0157 LXI 0305 Linn 0157 MCS 0029 MTC 0420 Magnavox 0157, 0305 Marantz 0626, 0029, 0157,

0180 Miro 0000 Mission 0157 NSM 0157 Nikko 0174 Onkyo 0868, 0101 Optimus 1063, 0000, 0032,

0037, 0145, 0179,

0305, 0420, 0437,

0468 Panasonic 0029, 0303 Parasound 0420 Philips 0626, 0157 Pioneer 1063, 1062, 0032,

0305, 0468 Polk Audio 0157

CD players (cont.)

Brand Code

Proton 0157 QED 0157 Quasar 0029 RCA 1062, 0032, 0053,

0179, 0305, 0468,

0764 Realistic 0179, 0180, 0420 Rotel 0157, 0420 SAE 0157 Sansui 0157, 0305 Sanyo 0179 Scott 0305 Sears 0305 Sharp 0861, 0037, 0180 Sherwood 1067, 0180 Sonic Frontiers 0157 Sony 0490, 0000, 0100,

0185, 0604, 1364 Soundesign 0145 TDK 1208 Tascam 0420 Teac 0174, 0180, 0393,

0420 Technics 0029, 0303 Victor 0072 Wards 0157, 0053 Yamaha 0888, 0036, 0187,

1292 Yorx 0461

Laser disk players

Brand Code

Aiwa 0203 Carver 0064, 0194, 0323 Denon 0059, 0172 Disco Vision 0023 Funai 0203 Harman/Kardon 0194 Hitachi 0023 Magnavox 0194, 0217 Marantz 0064, 0194 Mitsubishi 0059 NAD 0059 Optimus 0059 Panasonic 0204 Philips 0064, 0194 Pioneer 0059, 0023 Polk Audio 0194 Quasar 0204 Realistic 0203 Samsung 0323 Sega 0023 Sony 0193, 0201 Technics 0204 Theta Digital 0194 Yamaha 0217

Miscellaneous audio devices

Brand Code

Aiwa 0010, 0159, 0404 Fisher 0052 JVC 0073 Jerrold 0520, 0459 Scientific Atlanta 0460 Sony 0010, 0159, 0576 Starcom 0459

Page 53

Chapter 6: Setting up your TV

TheaterNet™ IR device codes (continued)

Video accessory (HDTV decoder)

Brand Code

Panasonic 1120 Pioneer 1010 Princeton 0113, 0295 Samsung 1190 Sensory Science 1126 Sharp 1010

Receivers

Brand Code

ADC 0531 Aiwa 1089, 1405, 0121,

Alco 1390 Anam 1609 Apex Digital 1257 Arcam 1120 Audiotronic 1189 Audiovox 1390 Bose 1229 Cambridge Soundworks Capetronic 0531 Carver 1089, 1189, 0042,

Casio 0195 Clarinette 0195 Compaq 1136 Curtis Mathes 0080 Daewoo 1250 Denon 1104, 1160, 0004,

Fisher 0042, 1801 Garrard 0463 Harman/Kardon 0110, 0189, 0891 Hewlett Packard 1181 JBL 0110, 1306 JVC 0074, 1374 KLH 1390 Kenwood 1313, 1027, 1570,

Koss 1366 LXI 0181 Lasonic 1798 Linn 0189 Lloyd’s 0195 MCS 0039 Magnavox 1089, 1189, 0189,

Marantz 1089, 1189, 0039,

Modulaire 0195 Musicmagic 1089 Nakamichi 0097 Onkyo 0135, 0842, 1298 Optimus 1023, 0042, 0080,

Panasonic 1518, 0039, 0309,

Penney 0195 Philips 1089, 1189, 1269,

Pioneer 1023, 0014, 0080,

Polk Audio 0189

0158, 0189, 0405, 1388, 1641

1370

0189

1360

1569, 0027, 0042, 0186

0195, 0391, 0531

0189

0181, 0186, 0531, 0670, 0738, 0801

0367

0189, 0391, 1120

0150, 0244, 0531, 0630, 1384

Receivers (cont.)

Brand Code

Proscan 1254 Quasar 0039 RCA 1023, 1254, 0080,

Realistic 0181, 0195 Samsung 1295 Sansui 1089, 0189 Sanyo 0801, 1251 Sharp 0186, 1286 Sherwood 0491, 0502, 1653 Sony 1058, 1258, 1158,

Soundesign 0670 Stereophonics 1023 Sunfire 1313 Teac 0463 Technics 1308, 1309, 1518,

Thorens 1189 Venturer 1390 Victor 0074 Wards 0014, 0080, 0158,

Yamaha 0176, 0186, 1176 Yorx 0195 Zenith 0857

0531, 1390, 1609

0158, 0474, 1367, 1558, 1658,1758

0039, 0309

0189

Satellite receivers

Brand Code

AlphaStar 0772 Chaparral 0216 Crossdigital 1109 DishPro 1005, 0775 Echostar 1005, 0775 Expressvu 0775 GE 0566 GOI 0775 General Instrument 0869 HTS 0775 Hitachi 0819 Hughes Network Systems JVC 0775 Magnavox 0724, 0722 Memorex 0724 Mitsubishi 0749 Motorola 0869 Next Level 0869 Panasonic 0247, 0701 Paysat 0724 Philips 1142, 0749, 0724,

Proscan 0392 RCA 0392, 0566, 0855,

RadioShack 0869 SKY 0856 Samsung 1109 Sony 0639 Star Choice 0869 Toshiba 0749, 0790, 1052,

Uniden 0724, 0722 Zenith 0856, 1856

1142, 0749, 1749

1076, 0722, 1749

0143

1053, 1054, 1285, 1286, 1287, 1289, 1749

VCRs

Brand Code

Admiral 0048, 0209 Adventura 0000 Aiko 0278 Aiwa 0037, 0000 Akai 0041 America Action 0278 American High 0035 Asha 0240 Audiovox 0037, 0278 Beaumark 0240 Bell & Howell 0104 Broksonic 0184, 0121, 0209,

CCE 0072, 0278 Calix 0037 Canon 0035 Carver 0081 Cineral 0278 Citizen 0037, 0278, 1278 Colt 0072 Craig 0037, 0047, 0240,

Curtis Mathes 0060, 0035, 0162,

Cybernex 0240 Daewoo 0045, 0278, 1278 Denon 0042 Dynatech 0000 Electrohome 0037 Electrophonic 0037 Emerex 0032 Emerson 0037, 0184, 0000,

Fisher 0047, 0104 Fuji 0035, 0033 Funai 0000 GE 0060, 0035, 0240,

Garrard 0000 Go Video 0432 GoldStar 0037, 0038, 1237 Gradiente 0000 HI-Q 0047 Harley Davidson 0000 Harman/Kardon 0081, 0038 Harwood 0072 Headquarter 0046 Hitachi 0000, 0042, 0041 Hughes Network Systems JVC 0067, 0041 Jensen 0041 KEC 0037, 0278 KLH 0072 Keen 0693 Kenwood 0067, 0041, 0038 Kodak 0035, 0037 LXI 0037 Lloyd’s 0000 Logik 0072 MEI 0035 MGA 0240, 0043 MGN Technology 0240 MTC 0240, 0000 Magnasonic 1278

0002, 0479, 1479

0072

0041, 0760, 1035

0121, 0043, 0209,

0002, 0278, 0479,

1278, 1479

0760, 0807, 1035,

1060

0042

Page 54

Chapter 6: Setting up your TV

TheaterNet™ IR device codes (continued)

VCRs (cont.)

Brand Code

Magnavox 0035, 0039, 0081,

0000, 0149, 0563,

1781 Magnin 0240 Marantz 0035, 0081 Marta 0037 Matsushita 0035, 0162, 0454 Memorex 0035, 0162, 0037,

0048, 0039, 0047,

0240, 0000, 0104,

0209, 0046, 0454,

0479, 1037, 1162,

1237, 1262 Minolta 0042 Mitsubishi 0067, 0043, 0807 Motorola 0035, 0048 Multitech 0000, 0072 NEC 0104, 0067, 0041,

0038 Nikko 0037 Noblex 0240 Olympus 0035 Optimus 1062, 0162, 0037,

0048, 0104, 0432,

0454, 1048, 1162,

1262 Orion 0184, 0209, 0002,

0479, 1479 Panasonic 1062, 0035, 0162,

0225, 0454, 0616,

1035, 1162, 1262

Penney 0035, 0037, 0240,

0042, 0038, 1035,

1237 Pentax 0042 Philco 0035, 0209, 0479 Philips 0035, 0081, 0618,

1081, 1181 Pilot 0037 Pioneer 0067 Polk Audio 0081 Profitronic 0240 Proscan 0060, 0760, 1060 Protec 0072 Pulsar 0039 Quarter 0046 Quartz 0046 Quasar 0035, 0162, 0454,

1035, 1162 RCA 0060, 0240, 0042,

0149, 0760, 0807,

1035, 1060 RadioShack 0000, 1037 Radix 0037 Randex 0037 Realistic 0035, 0037, 0048,

0047, 0000, 0104,

0046 ReplayTV 0614, 0616 Runco 0039 STS 0042 Samsung 0240, 0045 Sanky 0048, 0039 Sansui 0000, 0067, 0209,

0041, 0479, 1479

Sanyo 0047, 0240, 0104,

0046

VCRs (cont.)

Brand Code

Scott 0184, 0045, 0121,

0043

Sears 0035, 0037, 0047,

0000, 0042, 0104,

0046, 1237 Semp 0045 Sharp 0048, 0807, 0848 Shintom 0072 Shogun 0240 Singer 0072 Sonic Blue 0614, 0616 Sony 0035, 0032, 0000,

0033, 0636, 1032,

1232

Sylvania 0035, 0081, 0000,

0043, 1781 Symphonic 0000 TMK 0240 Tatung 0041 Teac 0000, 0041 Technics 0035, 0162 Teknika 0035, 0037, 0000 Thomas 0000 Tivo 0618, 0636 Toshiba 0045, 0043, 0845 Totevision 0037, 0240 Unitech 0240 Vector 0045 Vector Research 0038 Video Concepts 0045 Videomagic 0037 Videosonic 0240 Villain 0000 Wards 0060, 0035, 0048,

0047, 0081, 0240,

0000, 0042, 0072,

0149, 0760 White Westinghouse 0209, 0072, 1278 XR-1000 0035, 0000, 0072 Yamaha 0038 Zenith 0039, 0000, 0209,

0033, 0479, 1479

DVD players

Brand Code

Aiwa 0641 Apex Digital 0672, 0717, 0755,

0794, 0796, 0797,

0830, 0856, 1100 Audiologic 0736 B & K 0655, 0662 Blue Parade 0571 Broksonic 0695 DVD2000 0521 Daewoo 0784 Denon 0490, 0634 Emerson 0591 Enterprise 0591 Fisher 0670 GE 0522, 0717 GPX 0699, 0769 Go Video 0715 Gradiente 0651 Greenhill 0717 Harman/Kardon 0582, 0702

DVD players (cont.)

Brand Code

Hitachi 0573, 0664 Hiteker 0672 JBL 0702 JVC 0558, 0623, 0867 KLH 0717 Kenwood 0490, 0534, 0682,

0737

Konka 0711, 0719, 0720,

0721 Koss 0651 Lasonic 0798 Magnavox 0503, 0675 Malata 0782 Marantz 0539 Microsoft 0522 Mintek 0717 Mitsubishi 0521 Nesa 0717 Next Base 0826 Norcent 0872 Onkyo 0503, 0627 Oritron 0651 Panasonic 0490, 0632, 1362,

1462, 1490 Philips 0503, 0539, 0646,

0854 Pioneer 0525, 0571, 0632 Polk Audio 0539 Princeton 0674 Proscan 0522 RCA 0522, 0571, 0717,

0822 Rotel 0623 Rowa 0823 Sampo 0698 Samsung 0573, 0820 Sansui 0695 Sanyo 0670 Sharp 0630 Sherwood 0633 Shinsonic 0533 Sony 0533, 0864, 1533 Sylvania 0675, 0821 Technics 0490 Techwood 0692 Theta Digital 0571 Toshiba 0503, 0695, 1045 Tredex 0800 Urban Concepts 0503 XBox 0522

Page 55

Chapter 6: Setting up your TV

Setting the AVHD device skip time

When you connect an external AVHD (audio/video hard drive) device—such as the Toshiba Symbio™ AVHD Recorder—to one of the TV’s IEEE1394 ports, you can use the AVHD device skip time feature to set the number of minutes the device will skip forward or backward when you press the SKIP buttons.

Note:

• This TV will work best with the Toshiba Symbio™ AVHD Recorder* for recording high definition and standard definition material from either tuner and for controlling live TV (pause/rewind/etc.). When the Symbio AVHD Recorder is connected to the TV, the remote control keys (LIVE, STOP, REW, PAUSE, PLAY, etc.) are automatically activated to allow pausing of live TV.

• When you connect an AVHD (or D-VHS) device, the TV Guide On Screen page 26 for device connection information. See Chapters 5 and 7 for details about setting up and using the TV Guide On screen® system.

To set the AVHD device skip time:

1. Press MENU and open the Setup menu.

2. Highlight AVHD Skip Time and press •.

3. Press y or z to select the AVHD skip time (1, 3, 5, or 15 minutes) and press ENTER.

To enjoy the full benefits of your Toshiba Symbio™ AVHD Recorder, you must first set up the TV Guide On Screen® system (see Chapter 5). Full Symbio™ AVHD Recorder benefits, including Intelligent One Touch recording, will not be available unless the TV Guide On Screen® system is fully operational. However, even if the TV Guide On Screen® system is not fully operational, manual recording is available as long as the TV Guide On Screen® system has acquired the necessary date and time data. If you experience any issues with your Symbio AVHD Recorder, please contact Toshiba Consumer Solutions by calling (800) 631-3811 or visiting

http://www.tacp.com/customersupport/contact.asp.

system is automatically configured to allow recording. See

Setup

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

AVHD Skip Time

Navigate

Select

Auto

2 Sec

15 min

Back Exit

CH RTN

1 min

3 min

5 min

Analog

15 min

EXIT

Setting the time and date

Note: If you already set up the TV Guide On Screen® system, the time and date were set automatically and you can skip this step.

To set the time and date:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3 below.)

3. Open the Time And Date menu, highlight Start Setup, and press ENTER.

Time And Date

Start Setup

Navigate

If you have not set up the TV Guide On Screen® system, the following screen will appear. To set the time, highlight TV Guide On Screen On Screen

setup sequence will start, and the time and date

will be set automatically.

Time And Date

Your TV Guide On Screen system can provide accurate

time and date information.

It is recommended you set up TV Guide On Screen

first and use it to obtain the time and date.

Manual

If you have already set up the TV Guide On Screen® system, or if you have not set up the time, the Time and Date setting screen will appear and you will need to manually set the time and date.

Time And Date

Date (MM/DD/YY)

Time (HH:MM)

Back Exit

CH RTN

Select

and press ENTER. The TV Guide

TV Guide On Screen

EXIT

/06 30/05

:11 11

Cancel

Setting the HDMI™ audio mode

To set the HDMI audio mode:

1. Press MENU and open the Setup menu.

2. Highlight HDMI 1 (or

2) Audio and press •.

3. Press z or y to select the HDMI audio mode (Auto, Digital, or Analog) and press ENTER. (Auto is the recommended mode). See “Connecting an HDMI or DVI device to the HDMI input” on page 21.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Auto

Digital

Analog

Auto

2 Sec

Back Exit

CH RTN

Select

EXIT

Cancel

Done

Note:

• If you highlight TV Guide On Screen

(above) to set the time and date through the TV Guide On Screen® system and a power outage occurs, the time and date will be updated automatically when the power is restored.

• If you highlight Manual (above) to set the time and date manually and a power outage occurs, you will lose the time and date settings when the power is restored.

• If you manually set the time and date and then perform TV Guide On Screen

setup, the manual time and date settings

will be overridden by the TV Guide On Screen® settings.

Page 56

Chapter 6: Setting up your TV

Viewing the CableCARD™ menu

A CableCARD™ enables you to view encrypted digital channels. See page 14 for connection and subscription information.

™

After the CableCARD appears in the Applications menu, with informational screens provided by your digital CableCARD below).

CableCard Connected -- Acquiring channel information.

CableCard services will only operate with cable signal connected to Antenna 1.

To view the CableCARD™ menu:

1. Press MENU and open the Applications menu.

2. Highlight CableCARD

3. Press z or y to select one of the side menu items and then

press ENTER to display the information.

Applications

TV Guide On Screen

Audio Player

Picture Viewer

Digital CC/Audio Selector

CableCARD

Navigate

Note: The CableCARD™ menu is for informational purposes only and has no user-adjustable options.

is inserted, a CableCARD™ option

™

service (see illustrations

™

and press •.

IP Service

Conditional Access

CableCARD(tm) Status

Network Setup

CableCARD(tm) Pairing

Back Exit

CH RTN

Select

EXIT

Setting the Quick Restart™ feature

With the Quick Restart™ feature set to ON, the TV will stay in Shutdown mode for several minutes after the TV is turned off (see Notes below).

If the TV is turned on from Shutdown mode, the full picture appears immediately.

™

Auto

2 Sec

15 min

Back Exit

CH RTN

feature:

Off

EXIT

To set the Quick Restart

1. Press MENU, and then press x or • until the Setup menu

appears.

2. Highlight Quick Restart and press •.

3. Press z or y to select either On or Off.

Setup

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

AVHD Skip Time

Gray Level

Quick Restart

Navigate

Select

Note:

If Quick Restart is set to OFF and you turn off the TV, it can take several seconds for the picture to appear when you turn on the TV again. See “Important notice about hot lamp restart,” below.

If Quick Restart is set to ON and you turn off the TV, the following will occur for a few minutes:

• the screen (lamp) will light dimly; and

• the fans will continue to run.

This is a function of the Quick Restart Shutdown mode and is not a TV malfunction. If you do not prefer this, set the Quick Restart feature to OFF.

When the Quick Restart feature is set to OFF, if you repeatedly turn the TV on and off in a short period of time, the useful service life of the lamp may be shorter than the average useful service life. See page 129.

IMPORTANT NOTICE ABOUT

“HOT LAMP RESTART”

When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen in the following situations:

• when the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes; or

• if the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes.

This is a property of DLP lamp technology

and is NOT a sign of malfunction.

Page 57

Chapter 6: Setting up your TV

Viewing the system statusViewing the digital signal meter

You can view the digital signal meter for the ANT 1 and ANT 2 digital TV input sources only.

To view the digital signal meter:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

3. A new set of Installation menu icons will appear on-screen, as shown below. Open the Terrestrial menu, highlight Signal Meter, and press ENTER.

Terrestrial

Input Configuration

Channel program

Channel Add/Delete

Signal Meter

To view the system status:

1. Press MENU and open the Setup menu.

2. Highlight Installation and press ENTER. A new set of Installation menu icons will appear on-screen, as shown below right.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

System Status

System Infomation

Navigate

Select

Back Exit

CH RTN

3. Open the System Status menu, highlight System Information, and then press ENTER.

4. Press x • to scroll through the menu bar to check the Product Information and Software Version.

System Information

Product Information

Brand: Model:

IEEE1394 GUID:

Toshiba

52HMX95

00003914-28343803

Done

System Information

Software Version

0.3.0

Mar 9 2005 - 12:37:10

FW:0.12

Sub:47

Done

EXIT

Navigate

Select

Back Exit

CH RTN

EXIT

4. Press yzx • to select the antenna input and digital

channel whose signal you want to check.

Note: The physical digital channel number listed in the Signal Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF channel numbers for your local digital stations.

Signal Meter

Signal Locked

Peak

Antenna 1

Physical Digital Channel 13

Virtual Digital Channel

N/A

Done

To close the screen and return to the Terrestrial menu:

Highlight Done and press ENTER.

To return to normal viewing:

Press EXIT.

To close the screen and return to the Installation menu:

Highlight Done and press ENTER.

To return to normal viewing:

Press EXIT.

Restore Factory Defaults

To restore all settings and channels to their factory default values:

1. Follow steps 1–3 above.

2. Press x • to scroll through the menu bar to select Factory Defaults.

3. Enter your PIN code (or 0000 if no PIN code has been set).

4. Highlight Yes and press ENTER. The TV will turn off automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to complete the restore process.

System Information

Press YES to confirm. After the TV turns off, unplug it and plug it dack in to complete the reset.

Yes No

To cancel the reset:

Highlight No and press ENTER.

Page 58

Using the TV Guide On Screen

interactive program guide

The TV Guide On Screen® system is a free, interactive, on-screen program guide built in to your Toshiba TV that lists schedules and information for TV programs in your area.

Note: Over-the-air or cable access to stations carrying TV Guide On Screen operate. The TV Guide On Screen® system does not work with satellite programming. Toshiba does not provide the TV Guide On Screen® data; rather, such data is provided by a third party, which is responsible for its accuracy and availability. Additionally, occasional compatibility issues may exist between the TV Guide On Screen® system contained in your TV and the data provided by the third party. If you experience any performance issues with your TV Guide On Screen® system, please contact Toshiba Consumer Solutions by calling (800) 631-3811 or visiting http://www.tacp.com/customersupport/contact.asp.

data is required for the TV Guide On Screen® system to

The TV Guide On Screen® system includes the following features:

• Streamlined on-screen assisted setup—Quickly and easily set up your TV Guide On Screen prompts (see “Setting up the TV Guide On Screen

system using the on-screen

system”

below).

• Program listings and INFO windows—Scroll through eight days of TV listings and view program information such as rating, stereo, HDTV, new episode.

• Watch TV and display TV Guide On Screen

information

simultaneously.

• Channel lineup customization—Customize your channel lineup so your favorite stations are listed first.

• Direct tuning—Directly tune the TV to a current program you want to watch by selecting it in the program guide.

• Reminders—

Schedule show reminders that will either display an on-screen notification banner or automatically tune the TV to the channel of the show for which you set the reminder.

• Recording—Easily schedule recording of one or more programs.

Note: A VCR or IEEE1394 recording device is required for recording. It is recommended that you connect your devices according to the instructions in Chapter 2.

• Search—Search for shows by category, by keyword, or alphabetically.

• On-screen help—The TV Guide On Screen

system contains

on-screen feature definitions and navigation instructions.

To open the TV Guide On Screen® system:

• While watching TV, press the TV GUIDE button on the remote control; —or—

• Press MENU, open the Applications menu, highlight TV Guide On Screen

, and press

Applications

TV Guide On Screen

Audio Player

Picture Viewer

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTN

EXIT

ENTER.

Note: After setting up the TV Guide On Screen® system, the program guide opens automatically by default when you turn on the TV. To turn off this feature, see page 45.

Setting up the TV Guide On Screen® system

Follow these instructions to set up the TV Guide On Screen

system so it can receive current program data for your area.

Note: If you move the TV to a different ZIP/postal code, you must perform the TV Guide On Screen® Setup process to reconfigure your TV Guide On Screen® system for the new location

If you have not already connected your antenna, cable box, and/or recording device, see Chapter 2 for connection instructions.

Note: You must connect a VCR or an IEEE1394 compatible recording device to use the TV Guide On Screen® system’s one-touch recording feature. It is recommended that you connect your devices according to the connection instructions in Chapter 2.

1. Press MENU and open the Setup menu.

2. Highlight Installation and then press ENTER to open the Installation menus. (A new set of menu icons will appear on-screen, as shown in step 3 below.)

3. Open the TV Guide On Screen Start, and then press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

4. Go to Chapter 5 for instructions on completing the setup. Read this chapter for details on using the TV Guide

On Screen

Auto

2 Sec

Navigate

Back Exit

CH RTN

Select

interactive program guide.

EXIT

Setup menu, highlight

TV Guide On Screen Setup

Start

Navigate

Select

CH RTN

Back Exit

EXIT

Page 59

Chapter 7: Using the TV Guide On Screen® interactive program guide

Navigating the TV Guide On Screen® system

• While watching TV, press the TV GUIDE button to open the TV Guide On Screen LISTINGS screen will appear with the current show highlighted.

• When the TV Guide On Screen pressing the TV GUIDE button from any screen will tune the TV to the show displayed in the Video Window.

• Use the arrow keys on the remote control (yzx •) to highlight any show, and then press ENTER to tune to that show.

• Scroll left or right (x •) to view eight days of listings.

• Press MENU to display a panel menu with options for the currently highlighted program or tile, including setting recordings and reminders.

• To access another Service screen:

1. Press y to highlight the Service Bar.

2. Press x or • to highlight a different Service (LISTINGS, SEARCH,

3. Press z to use that Service.

system. The

system is open,

SETUP, SCHEDULE, or RECORDINGS).

Note: Helpful information about each Service appears in the Info Box.

Note:

• The TV Guide On Screen illustration purposes only. The channels, programs, and TV Guide On Screen available in your area. The options and features as illustrated are subject to change when updates are downloaded from the TV Guide On Screen

• The TV Guide On Screen cable-ready, cable box, and digital cable services, as well as over-the-air broadcasts, but does not provide listings for satellite services.

menus shown in this manual are for

information as illustrated may not be

service to your TV.

interactive program guide supports

TV Guide On Screen® remote control functions

BUTTON FUNCTION

TV GUIDE • When watching TV, opens the TV Guide On Screen® system and highlights the current show

Numbers • For direct channel tuning, priority ordering, and channel editing.

– (digital separator) • For entering digital channel numbers.

MENU • Displays the panel menu, in which you can choose options (record, remind, keyword, etc.).

INFO • Cycles between levels of information, as available, in a Service screen or other type of screen.

ENTER • Makes a selection or executes an action.

yzx • • Provide directional control.

PAGE UP/DOWN • When the TV Guide On Screen

REC • When the TV Guide On Screen® system is open or when watching TV, starts recording.

SPLIT • When the TV Guide On Screen

SS| and |TT • Jump forward and backward one day in the LISTINGS screen.

listing.

• When the TV Guide On Screen tunes the TV to the show displayed in the Video Window.

• With a currently airing show listing highlighted, returns to watching TV and tunes to the show channel.

• With a future airing show listing highlighted, displays a panel menu with viewing options.

• When watching TV, y and z surf through channels you set to “ON” in the LISTINGS screen.

the next, when applicable.

Video Window.

system is open, closes the TV Guide On Screen® system and

system is open, moves from one set of screen information to

system is open, toggles between locking and unlocking the

– (digital

separator)

INFO

TV GUIDE

ENTER

x •

PAG E U P/

DOWN

SS| and |TT

REC

SPLIT

Numbers

}

Page 60

Chapter 7: Using the TV Guide On Screen® interactive program guide

Navigating the TV Guide On Screen® system (continued)

Video Window

• When you open the TV Guide On Screen system, the current program appears in the Video Window.

• As you scroll through the listings, the Video Window will change to display the selected program.

• The lock/unlock icon indicates the status of the Video Window.

If you lock the Video Window:

As you navigate through listings, the Video Window channel will remain on the channel it was tuned to when you locked it.

If you unlock the Video Window:

As you navigate through listings, the Video Window channel will change to the currently highlighted listing.

Info Box

To lock/unlock the Video Window:

Press the SPLIT button on the remote control to toggle between locking and unlocking the Video Window. —or— Highlight a channel logo or the LISTINGS Service Bar Label and press MENU to display the option to lock/unlock the Video Window.

Panel Menus

• A panel menu appears: – when you press MENU on a highlighted tile (if additional options

are available); or

– when you press ENTER on a show starting in the future.

• When a panel menu appears, the highlighted tile changes color to indicate that the panel menu relates to the tile.

• Press INFO to display help for the current panel menu.

• Press y and z to move among the options.

• Press x and • to move to adjacent options or, if the highlight is on an odometer, to change the odometer choice.

• To move the highlight to the default command button, press ENTER from an odometer or entry box.

• To execute the action and close the panel menu, highlight the command button and press ENTER.

• To cancel any changes and close the panel menu: – press MENU; or – highlight Cancel and press ENTER.

• If a panel menu contains more options than can be displayed in one panel, the word “more” appears at the bottom of the menu. To access the additional options, either scroll down using the z button or the PAGE UP/DOWN (CH yz) button.

Page 61

Chapter 7: Using the TV Guide On Screen® interactive program guide

Navigating the TV Guide On Screen® system (continued)

Info Box

• An Info Box contains information about a show, Service, or Panel Ad, or provides general help (for example, for a panel menu).

• An Info Box for a program in the LISTINGS screen can have up to three sizes: Small, Large, or “No.”

– Press INFO on the remote control to cycle among the sizes. – The default Info Box size is Small. To change the default size, open the

SETUP Service screen (see page 70).

• The Info Button icon ( Box size can change and/or if there are additional Info screens. Press the INFO key on the remote control to change the size and/or display additional Info screens.

• In some instances, the INFO button on the remote control is used to page forward (for example, if there are additional pages of information in a Panel Ad, a Channel Ad, or help text).

) appears on the Info Action Bar if the Info

Info Action Bar

Small Info Box

Large Info Box

TV Guide On Screen® Icons

ICON NAME DESCRIPTION

Info Button • Additional Info Box information is available, or the Info Box has additional sizes.

Progress Bar • Elapsed time in current show.

• Progress bar appears in LISTINGS and SEARCH and when the Info Button is pressed while watching TV.

HDTV • Show is presented in high-definition TV, if available.

New • Show is new (not a repeat).

Stereo • Show is available in stereo.

Dolby Digital • Show is available with Dolby Digital 5.1 audio (digital channels only).

CC • Closed captioning is available for the show.

TV Rating • TV rating for the show.

Record Once • Show is set to record once.

• Other frequencies are Daily (manual recording only), Regularly, and Weekly.

Record Off • Show is set to record but recording is currently Off (show remains in schedule).

Record Suspended • Recording resumes when the conflict no longer exists.

Remind Once • Show is set to remind once.

• Recording is suspended due to a schedule conflict (show remains in schedule).

• Other frequencies are Daily (manual reminding only), Regularly, and Weekly.

Remind Off • Show is set to remind but reminder is currently Off (show remains in schedule).

Remind • Reminder is suspended due to a schedule conflict (show remains in schedule). Suspended

• Reminder resumes when the conflict no longer exists.

Page 62

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services

The TV Guide On Screen® system consists of five main services: LISTINGS, SEARCH, RECORDINGS, SCHEDULE, and SETUP.

Note:

• For the RECORDINGS service to display, an IEEE1394 recording device must be connected to the television (see Chapter 2); otherwise, only four services display. Recording to other devices, such as a VCR, is possible from within the LISTINGS service.

• When using the TV Guide On Screen make sure your system is set up properly.

• If the power is cut or the plug becomes disconnected during timer recording, any recorded contents will be lost. It may take up to 7 days before an entire program schedule is available.

• If the TV power cord is unplugged for an extended period of time, it may take up to 24 hours with the TV in standby mode (power cord plugged in and power OFF) to download the entire TV Guide On Screen program schedule is available. Be sure to follow the instructions under “TV Guide On Screen® Reminder” on page 45.

LISTINGS screen

system to record a program for the first time, it is recommended that you perform a test recording to

program schedule. It may take up to 7 days before an entire

• When you open the TV Guide On Screen® system, LISTINGS is always the first service displayed.

• With LISTINGS highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen.

• Use the arrow keys to move the highlight within LISTINGS to do the following: – View eight days of show listings – Read show descriptions

• Use the Number keys on the remote control to jump to a specific channel’s listings.

• To watch a show (if on now), highlight the show and press ENTER.

• To display the Episode Options panel menu for a particular show, highlight a show and press MENU.

Episode Options panel menu

From the Episode Options panel menu, you can choose to set a recording, set a reminder, or tune to the channel. The following are descriptions of the buttons.

GO TO SERVICE BAR: Closes the menu, changes no information, and returns to the Service Bar.

TUNE TO CHANNEL / WATCH NOW: Exits the TV Guide

On Screen

system and tunes to the show (if the show is currently airing) or tunes to the channel of the highlighted show (if the show airs in the future). The button label changes according to whether the show is currently airing or not.

– Tune directly to a show currently airing – Set a show to Remind (e.g., start time, frequency,

automatic power ON, auto-tune TV) – Set a show to Record (e.g, start/end time, frequency) – Lock and unlock the Video Window – Access panel ads and channel ads

SET RECORDING: Displays the Record Options panel menu, from which you can set the show to record. For additional information, see “SCHEDULE screen” and “Recording features” on page 66.

SET REMINDER: Displays the Remind Options panel menu, from which you can set a reminder for the show. For additional information, see “SCHEDULE screen” on page 66 and “Remind features” on page 68.

CANCEL: Closes the menu, changes no information, and returns to the highlighted show.

Page 63

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

SEARCH screen

• SEARCH allows you to find shows by keyword, alphabetically, or by category (HDTV, Movies, Sports, Children, Educational, News, Variety, Series).

• With SEARCH highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen.

• Use the arrow keys to move the highlight within SEARCH.

Example: Category search

1. From the SEARCH screen, press z to highlight a category

(in this example, MOVIES).

2. Press z to highlight a subcategory (in this example, ALL).

3. Press ENTER to display a list of all movies, organized by date and time.

4. Highlight a show and press ENTER to watch (if on now) or press MENU to display the Episode Options panel menu. (See “Episode Options panel menu” on page 62.)

Page 64

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

SEARCH screen (continued)

Example: Keyword search

Keyword search lets you enter a word(s) to find a particular show by category or for every show title that matches.

1. From the SEARCH screen, highlight KEYWORD, and then press ENTER.

2. Highlight NEW SEARCH in the panel menu, and then press ENTER.

3. The Search Options panel menu opens. Highlight CATEGORY, and then use the arrow keys to highlight a category to search (All, HDTV, Children, Sports, etc.).

4. After highlighting a category, press z to highlight ENTER KEYWORD, and then press ENTER.

6. A list of all matching shows for that keyword is displayed.

7. Highlight a show and press ENTER to display all airings. Then highlight a specific listing and press ENTER to watch (if on now) or press MENU to display the Episode Options panel menu. From the Episode Options menu, you can choose to set a recording or reminder, or tune to the channel (see “Episode Options panel menu” on page 62.)

5. The keyboard is displayed. Use the arrow keys to highlight a character and then press ENTER to display it. When finished entering all characters, highlight DONE and press ENTER.

The TV Guide On Screen® system stores all the keywords you create.

To edit or delete a keyword:

From the SEARCH/KEYWORD screen, highlight the keyword you want to edit or delete, and then press MENU to display the Search Options panel menu, with the following options:

– GO TO SERVICE BAR: Closes the menu, changes no

information, and returns to the Service Bar.

– EDIT SEARCH: Displays the keyboard, from which you

can change the keyword.

– DELETE SEARCH: Displays the Confirmation panel

menu. Select YES to delete the search or NO to close the panel menu.

– CANCEL: Closes the panel menu, changes no

information, and returns to the highlighted keyword.

Page 65

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

RECORDINGS screen

The RECORDINGS service screen displays a list of shows that were previously recorded or are currently recording on an IEEE1394 recording device connected to the TV.

Note: RECORDINGS will not appear in the Service Bar unless you have an IEEE1394 video recording device connected to one of the IEEE1394 ports on the TV. See Chapter 2 for details.

For additional details, see “Recording features” on page 66.

• With RECORDINGS highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen.

To choose the way recordings are displayed:

1. Highlight RECORDINGS on the Service Bar and press MENU to display the Recording Options panel menu.

2. Press yz to choose between View As and Sort By, as described below.

View As: Press x • to choose between the following:

• List—Displays every recorded episode for a show (see example in Screen A, at right).

Note: In List view, highlight an episode to display an Info Box with show information. Press MENU to display the Episode Options panel menu (see “Episode Options panel menu” on page 62).

• Group—Displays recorded shows without listing every recorded episode (see example in Screen B, at right).

Note: In Group view, highlight a show and press ENTER to view all recorded episodes. Press ENTER again to collapse the episode list.

To view a recording, you can do one of the following:

• Highlight an episode and press ENTER to view it now. The episode either starts from the beginning or from where it was last stopped (if viewed previously).

• Highlight an episode and press MENU to display the Episode Options panel menu, with the following options:

– GO TO SERVICE BAR: Closes the menu, changes no

information, and returns to the Service Bar.

– RESUME: Starts from the beginning or from where it

was last stopped (if viewed previously).

– PLAY FROM BEGINNING: Starts from the beginning,

even if stopped previously.

– DELETE EPISODE: Deletes the episode from the

RECORDINGS list and deletes the recording from the IEEE1394 recording device. A Confirm panel menu displays. Press YES to delete the episode or NO to close the panel menu.

– CANCEL: Closes the panel menu, changes no

information, and returns to the highlighted show.

Screen A

Sort By: Press x and • to choose between the following:

• Title—Displays recorded shows in alphabetical order (see example in Screen A, at right).

• Date—Displays recorded shows by date and time, with the most recent first.

3. When finished, press ENTER to highlight DONE, and then press ENTER again to close the panel menu and display the recordings with the selected options.

Screen B

Page 66

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

SCHEDULE screen

The SCHEDULE service screen allows you to review, edit, or delete Record and Remind events you set previously.

• With SCHEDULE highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen.

• Highlight an event and press MENU to display the Schedule Options panel menu, with the following options (as applicable):

GO TO SERVICE BAR

–

information, and returns to the Service Bar.

WATC H NOW

–

tunes to the highlighted show.

SET RECORDING

–

recording for a show (does not cancel a set reminder).

DELETE RECORDING

–

schedule. A Confirm panel menu displays. Press YES to delete the recording or NO to close the panel menu.

EDIT RECORDING

–

change existing recording information.

SET REMINDER

–

reminder for a show (does not cancel a set recording).

DELETE REMINDER

–

schedule. A Confirm panel menu displays. Press YES to delete the reminder or NO to close the panel menu.

EDIT REMINDER

–

existing reminder information.

CANCEL

–

: Closes the panel menu, changes no information,

and returns to the highlighted show.

An icon identifies the event type. For more details, see “Recording features,”at right, and “Reminder features” on page 68.

: Closes the menu, changes no

: Exits the TV Guide On Screen® system and

: Opens a menu in which you can set a

: Removes the recording from the

: Opens a menu in which you can

: Opens a menu in which you can set a

: Removes the reminder from the

: Opens a menu in which you can change

Recording features

You can set a show to record, or edit the recording settings for a show, in the LISTINGS, SEARCH, and SCHEDULE screens. There are three ways to set a show to Record, as described below.

1) Set a show to Record using the REC key on the remote control

Press the REC key on the remote control to record the show Once with current default settings (start and end recording on time). Each time you press REC, you change the Record frequency (but not the default settings) among Once (default), Regularly, Weekly, and Cancel.

Note: The related Record icon appears on the show tile each time you press REC. See “Record icons,” on page 67.

2) Set a show to Record from a panel menu

1. Highlight a show and press MENU to display the

Episode Options panel menu.

2. Highlight SET RECORDING and press ENTER to

display the Record Options panel menu.

3. Highlight the FREQUENCY field, and press x or • to

choose among Once, Regularly, Weekly, or Off.

4. Highlight the START field, and press x or • to choose

in the range from 120 minutes early to 120 minutes late or On Time (default = On Time).

5. Repeat step 4 for the END field.

6. Highlight the RECORDER field and press x or • to

choose the recording device.

Note: For connected IEEE1394 recording devices only.

7. Highlight the KEEP UNTIL field and press x or • to

choose how long you want to keep the Record event.

Note: For connected IEEE1394 recording devices only.

8. Press ENTER to highlight SCHEDULE RECORDING,

and press ENTER again to close the menu. A Record icon for the selected frequency appears on the

show tile. See “Record icons” on page 67.

Note: For connected IEEE1394 recording devices only.

Or highlight CANCEL and press ENTER to close the menu, change no information, and return to the highlighted show.

Note: You can change the default values of the Record Options panel menu fields. See “Change default options” on page 71.

Page 67

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

Recording features (continued)

3) Manually set a show to Record

1. Highlight SCHEDULE in the Service Bar, and press MENU to display the Schedule Options panel menu.

2. Highlight NEW MANUAL RECORDING and press ENTER to display the Record Options panel menu.

Press yzx • to move through the options. Press the Number keys or yzx • to change the

information, as necessary.

3. Enter the information in the panel menu fields. You will need to set the start and end time for the recording. For details, see “Set a show to Record from a panel menu” on the previous page.

Note: When setting a Manual Recording, the frequency option “Daily” is available instead of “Regularly.” See “Record icons,” below right, for a description of the Record icons.

4. When finished entering the information in the fields, press ENTER to highlight SCHEDULE RECORDING, and press ENTER again to close the menu.

A Record icon for the selected frequency appears on the show tile. See “Record Icons,” below right.

Note: Manual recording is listed by channel number.

Or highlight CANCEL and press ENTER to close the menu, change no information, and return to the highlighted show.

Recording conflict

A recording conflict message will appear in the following situations:

• A show set to Record overlaps with any part of another show previously set to Record.

• A show set to Record overlaps with a show previously set to auto-tune. (For auto-tune details, see “Remind features” on page 68.)

Select one of these options:

• Record Anyway—This show will override an existing show set to Record or auto-tune.

• Don’t Record This Show—Cancels the Recording.

Record icons

Following is a description of the Record icons that will appear on the tile for a show set to Record.

• Record Once —Records the show one time.

When using the TV Guide On Screen® system to record a program for the first time, it is recommended that you perform a test recording to make sure your system is set up properly.

Recording notification banner

• If the TV is not on, the recording occurs as scheduled.

• If the TV is on and you are watching the channel that is set to record, the recording occurs as scheduled.

• If the TV is on and you are watching a channel other than the one that is set to record, a notification banner (illustrated below) appears on-screen before recording starts. At that time you can choose to start or cancel recording.

The default highlighted item in the notification banner is “Change channel; start recording.” If no change is made within 3 minutes, the notification banner will close automatically, the channel will change to the one set to record, and the recording will occur as scheduled. If you want to cancel the recording, select “Don’t change; cancel recording” in the notification banner and press ENTER.

• Record Regularly

—Records the show every time the

show airs on the same channel and starts at the same time.

• Record Weekly

—Records the show every time the show airs on the same day of the week and on the same channel, and starts at the same time.

• Record Daily

—Records on the same channel and at the

same start time every weekday (Monday through Friday).

Note: This icon displays for manual recordings only.

• Record Suspend —Recording is Suspended due to a schedule conflict (show remains in the Schedule list).

• Record Off

—Keeps the Recording in the Schedule list

but will not record this show until the frequency is changed.

Page 68

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

Reminder features

You can set a Reminder to perform the following functions:

• Automatically turn on the TV (if off) at the scheduled reminder time, and tune the TV to the channel of the show for which you set the reminder.

• Automatically tune the TV, at the scheduled reminder time, to the channel of the show for which you set the reminder.

• Display an on-screen notification banner (reminding you that the show is about to start), from which you can choose to tune the TV to the show’s channel or cancel the reminder.

You can set a show reminder, or edit the reminder settings for a show, in LISTINGS, SEARCH, and SCHEDULE. There are two ways to set a show reminder, as described below.

1) Set a show Reminder from a panel menu

1. Highlight a show and press MENU to display the Episode Options panel menu.

2. Highlight SET REMINDER and press ENTER to display the Remind Options panel menu.

7. Press ENTER to highlight SCHEDULE REMINDER, and press ENTER again to close the menu. A Remind icon for the selected frequency appears on the show tile. See “Remind icons” on page 69.

Or highlight CANCEL and press ENTER to close the menu, change no information, and return to the highlighted show.

2) Manually set a show Reminder

1. Highlight SCHEDULE in the Service Bar, and press MENU to display the Schedule Options panel menu.

2. Highlight NEW MANUAL REMINDER and press ENTER to display the Remind Options panel menu.

Press yzx • to move through the options. Press the Number keys or yzx • to change the

information, as necessary.

3. Highlight the FREQUENCY field, and press x or • to

choose among Once, Regularly, Weekly, or Off.

4. Highlight the POWER ON TV field, and press x or •

to choose either Yes (to turn on the TV automatically, if off, at the scheduled Reminder time) or No (default).

5. Highlight the AUTO TUNE TV field, and press x or •

to choose either Yes (to automatically tune the TV to the channel you are setting the Reminder for at the scheduled Reminder time; the TV must be on at the time) or No (default).

Note: You can change the default values of the Remind Options panel menu fields. See “Change default options” on page 71 for details.

6. Highlight the WHEN field (to set a time for displaying

the reminder screen), and press x or • to choose in the range from 15 minutes early to 15 minutes late or On Time (default = 1 minute early).

3. Enter the information in the panel menu fields. You will need to set the start and end time for the reminder. For details, see “Set a show Reminder from a panel menu,” at left.

Note: When setting a Manual Reminder, the frequency option “Daily” is available instead of “Regularly.” See “Remind icons,” on the following page, for a description of Reminder icons.

4. When finished entering the information in the fields, press ENTER to highlight SCHEDULE REMINDER, and press ENTER again to close the menu.

A Remind icon for the selected frequency appears on the show tile. See “Remind icons” on the following page.

Note: Manual reminders are listed by channel number.

Or highlight CANCEL and press ENTER to close the menu, change no information, and return to the highlighted show.

Page 69

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

Reminder features (continued)

Reminder notification banner

Based on your option settings, a notification banner will appear on-screen if your TV is on at the scheduled Reminder time.

At that time you can either press ENTER to hide the Reminder banner or highlight the show and press ENTER to tune to the show.

If no choice is made within 3 minutes, the notification banner closes automatically and performs the highlighted option (default is HIDE REMINDERS).

Note: If more than two reminders are set for the same time, arrows appear on the Reminder notification banner. Press yz to highlight the shows.

Reminder conflict

A conflict message will appear in the following situations:

• A show set with an auto-tune Reminder has the same start time as an existing auto-tune Reminder.

• A show set with an auto-tune Reminder overlaps with a scheduled Recording.

Select one of these options:

• Auto-Tune Anyway—This show will override an existing show set to auto-tune.

• Proceed, No Auto-Tune—Set the show as a Reminder but do not auto-tune.

• Don’t Set This Reminder—Cancels the Reminder.

Remind icons

Following is a description of the Remind icons that will appear on the tile for a show set to Remind.

• Remind Once

• Remind Regularly time the show airs on the same channel and starts at the same time.

• Remind Weekly the show airs on the same day of the week and on the same channel, and starts at the same time.

• Remind Daily weekday (Monday through Friday) for the same channel and start time.

Note: This icon displays for manual reminders only.

• Remind Suspend —Reminder is Suspended due to a schedule conflict (show remains in Schedule).

• Remind Off but will not display a reminder until you change the frequency.

—Displays a show reminder one time.

—Displays a show reminder every

—Displays a show reminder every time

—Displays a show Reminder every

—Keeps the Reminder in the Schedule list

Page 70

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

SETUP screen

The SETUP service screen allows you to change the following settings:

• System settings

• Channel display

• Default options

Note: You must complete the TV Guide On Screen® setup (as described in Chapter 5) before you can change these settings.

With SETUP highlighted in the Service Bar, highlight the settings you want to change, press ENTER, and follow the on-screen instructions.

With SETUP highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen.

Change channel display

This option allows you to edit channel information that appears in LISTINGS, including the following:

• Reorder the position the channels appear in LISTINGS.

• Change the “tune channel” number.

Note: The “tune channel” is the channel on which you receive a station. For example, two viewers in the same zip code may receive the same station on different channel numbers, depending on whether they have Cable service or are using a cable box.

• Switch a channel to one of the following settings:

– On (channel is always displayed in LISTINGS) – Off (channel is never displayed in LISTINGS) – Auto-Hide (channel is displayed in LISTINGS only

when program information is available)

1. From the SETUP screen, highlight CHANGE CHANNEL DISPLAY and press ENTER.

Change system settings

This option appears only after you have completed the initial TV Guide On Screen

setup process (as described in Chapter 5).

1. From the SETUP screen, highlight CHANGE SYSTEM SETTINGS and press ENTER.

2. Press ENTER again to display the Confirming Your Settings screen.

3. Highlight one of the options, press ENTER, and follow the on-screen instructions.

2. Highlight the channel row you want to edit and press ENTER to display the Grid Options panel menu.

3. To edit the options, press INFO and follow the on-screen instructions.

Page 71

Chapter 7: Using the TV Guide On Screen® interactive program guide

TV Guide On Screen® Services (continued)

SETUP screen (continued)

Change default options

This option allows you to change default settings in the following categories:

• General defaults

• Record defaults

• Remind defaults

General defaults

1. From the SETUP screen, highlight CHANGE DEFAULT OPTIONS and press ENTER.

2. Highlight GENERAL DEFAULTS and press MENU to display the General defaults panel menu.

Record defaults

1. From the SETUP screen, highlight CHANGE DEFAULT OPTIONS and press ENTER.

2. Highlight RECORD DEFAULTS and press MENU to display the Record Defaults panel menu.

3. Enter the required information in the panel menu fields (start time, end time, recorder choice, how long to keep a Record event, the quality of the recording). See “Record features” on page 66 for details on entering values in these fields.

4. When finished, press ENTER to highlight DONE, and then press ENTER again to close the menu and accept the changes (or highlight CANCEL to close the menu with no changes).

3. Enter the following information in the panel menu fields:

• BOX SIZE: The initial Info Box size when you open the TV Guide On Screen

system. Choices are No, Small

(default), Large, and Last Used.

• BOX CYCLE: The Info Box size rotation when you press INFO on the remote control when the TV Guide On Screen

system is open. Choices are No Only, Small Only, Large Only, No & Small, No & Large, Small & Large, and All (default).

• AUTO GUIDE: Automatic entry into the TV Guide On Screen

system when the TV is powered on. Choices

are On (default) and Off.

Note: Set the AUTO GUIDE to Off if you do not want the TV Guide On Screen® system to open every time you turn on the TV.

4. When finished, press ENTER to highlight DONE, and press ENTER again to close the menu and accept the changes (or highlight CANCEL to close the menu with no changes).

Remind defaults

1. From the SETUP screen, highlight CHANGE DEFAULT OPTIONS and press ENTER.

2. Highlight REMIND DEFAULTS and press MENU to display the Remind Defaults panel menu.

3. Enter the required information in the panel menu fields (power On TV, auto-tune, when to display the Remind screen). See “Reminder features” on page 68 for details on entering values in these fields.

4. When finished, press ENTER to highlight DONE, and then press ENTER again to close the menu and accept the changes (or highlight CANCEL to close the menu with no changes).

Page 72

Using the TV’s features

Selecting the video input source to view

To select the video input source to view:

1. Press INPUT on the remote control or TV/VIDEO on the TV front panel.

2. Press 0–9 to select the input source you want to view, which will depend on the input terminals you used to connect your devices (see Chapter 2).

The current signal source displays in the top right corner of the Input Selection screen.

Input Selection

ANT 1ANT 1

Video 1

Video 2

Video 3

ColorStream HD1

ColorStream HD2

HDMI 1

HDMI 2 PC

8 9

ANT 2

INPUT

- / to Select

ANT 1

Numbers

INPUT TheaterNet DEVICE

Note:

• When the Input Selection screen is open, you also can use the yz

buttons on the remote control (or the Channel yz buttons on the front panel) to change the input.

• You can repeatedly press the INPUT button on the remote control

or the TV/VIDEO button on the TV front panel to change the input.

• To select an IEEE1394 input source, press the TheaterNet DEVICE

button on the remote control (see page 31 and 51).

• If an IEEE1394 device is the current input, it will appear at the

bottom of the Input Selection list; however, it will not display in the list if you change the input source.

• You can label the video input sources according to the specific

devices connected to the TV (see “Labeling the video input sources” on the next page).

• The source can be “hidden.” See page 73 for details.

Remote control

TV front panel touchpad

CHANNEL

TV/VIDEO

{

Page 73

Chapter 8: Using the TV’s features

Labeling the video input sources

You can label each video input source according to the type of device you connected to each source, from the following preset list of labels:

– – (default label) Hide (to hide an unused input in the Input Selection window) Audio Receiver VCR Video Recorder Laser Disk Compact Disc DVD DTV Satellite/DSS Cable Game Console

Note:

• If you set up devices in TheaterNet,™ the associated inputs are automatically labeled and cannot be relabeled until you remove the device from TheaterNet (see page 50).

• If you set up a cable box in VIDEO 1, that input will be labeled automatically and cannot be relabeled until you remove the device from the TV Guide On Screen

setup.

• You cannot select IEEE1394 devices through the Input Selection window; however, you can select and control IEEE1394 devices through TheaterNet (see page 50).

To label the video input sources:

1. Press MENU and open the Preferences menu.

2. Highlight Input Labeling and press ENTER.

3. Press y or z to highlight the video source you want to

label.

4. Press x or • to select the desired label for that input source.

If a particular input is not used, you can select “Hide” as the label, which will cause that input to be “grayed out” in the input list and skipped over when you press the INPUT button on the remote control.

Note: If you select “Hide” for all of the input labels, the POP feature will be disabled. If you then attempt to access the POP feature, the message “NOT AVAILABLE” will appear on-screen.

5. To save the new input labels, highlight Done and press ENTER. To revert to the factory default labels, highlight Reset and press ENTER.

Input labeling example:

The screen below left shows the default Input Selection screen (with none of the inputs labeled). The screen below right is an example of how you could label the inputs if you connected a DVD player to VIDEO 1, Cable TV to VIDEO 2, an audio receiver to VIDEO 3, a video recorder to ColorStream HD1, a DTV set-top box to HDMI 1, and a satellite/DSS set-top box to HDMI 2. Also note that the ColorStream HD2 input is labeled “Hidden,” which means that the input will be skipped over when INPUT or TV/VIDEO is pressed.

Input Selection ANT 1

ANT 1ANT 1

Video 1

Video 2

Video 3

ColorStream HD1

ColorStream HD2

HDMI 1

HDMI 2 PC

8 9

ANT 2

INPUT

- / to Select

Input Selection screen Input Selection screen with with no inputs labeled all inputs labeled except input 5,

Input Selection ANT 1

ANT 1ANT 1

DVD

Cable

Audio Receiver

Video Receiver

ColorSteram HD2 (Hidden)

DTV

Satellite/DSS

8 9

ANT 2

- / to Select

which has been hidden.

INPUT

Preferences

Favorite Channels

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language

Home CH Setup

Navigate

Input Labeling

Video 1 DVD

Video 2 Cable

Video 3 Audio Receiver

ColorStream HD 1 Video Receiver

ColorStream HD 2 Hide

HDMI 1 DTV

HDMI 2 Satellite/DSS

ANT 2

Reset

Select

Off

English

Back Exit

CH RTN

Done

To clear the input labels:

1. Press MENU and open the Preferences menu.

2. Highlight Input Labeling and press ENTER.

3. Highlight Reset and press ENTER.

EXIT

Note: If you set up a device in TheaterNet, its input label will not be cleared unless you remove the device from TheaterNet (see page 50).

Page 74

Chapter 8: Using the TV’s features

Tuning channels

Using the Channel Browser™

The Channel Browser stores in the channel history up to 32 of the most recently viewed channels. This feature allows you to:

• Keep a separate, temporary* history of the last 32 channels tuned from each of three inputs: ANT 1, ANT 2, and Cable Box.

Note: Turning off the TV will clear the channel history for all three inputs.

• Quickly surf and tune your recently viewed channels from the Channel Browser banner (illustrated below).

• Surf via Browse mode (to immediately tune channels as you highlight them in the Channel Browser banner) or Select mode (to surf over channels in the browser banner before you select one to tune).

• Set a “HOME” channel for the ANT 1, ANT 2, and Cable Box inputs.

To open the Channel Browser banner: Press x ( ), • ( ), or ENTER on the remote control.

– Press x (

input, which are automatically stored in the channel history for the current input (ANT 1, ANT 2, or Cable Box only).

– Press • (

Elements of the Channel Browser banner

) to surf back from the most recently viewed channel through the last 32 channels that were tuned from the current

) to surf forward from the previous channels in the channel history up to the most recently viewed channel.

Active channel

status

(Displays in this area

only if available.)

12-3

12345678

Select Mode

Highlighted channel

(Displays with a yellow

background

Displays with a yellow

outline

in Browse mode.)

Current mode

(Select or Browse)

in Select mode.

ABCD-DTV

ANT 1 CABLE 3 XYZ 480p 17-2

Current

input

Channels stored

in the channel

history

26-1

QRS

Current

antenna type

(cable or TV)

channel number

Active channel

(In Browse mode, because the highlighted

channel is tuned automatically, the active

channel and the highlighted channel

will always be the same.)

17-2

TUV

Channel call

letters

(if available)

XYZ

ResolutionActive

Home channel instructions

3 sec to program

[Press

x ( ) or • ( )

to surf the other channels

in the channel history.]

Hold HOME key

Home channel

To toggle between Browse mode and Select mode:

After opening the Channel Browser banner, press y or z to toggle between Browse mode and Select mode. The “Current mode” field on the Channel Browser banner will flash green.

To tune to a channel in Browse mode:

1. While watching TV, press x (

) or •( ) to open the

Channel Browser banner and surf back to a previous channel or surf forward to the next channel in the channel history.

In Browse mode, when you stop on a channel number in the browser banner, it will be highlighted with a yellow outline and the TV will automatically tune to the channel.

2. Press EXIT to close the Channel Browser banner.

3 2 102-1

Browse Mode

ANT 1 CABLE Ch.102-1 1080i

In Browse mode, the highlighted channel number is outlined in yellow and the channel will be tuned to automatically.

Note:

The Channel Browser banner will close automatically if

you do not make a selection within 60 seconds.

Note: The Channel Browser banner opens in Browse mode by default.

To tune to a channel in Select mode:

1. While watching TV, press x (

) or •( ) to open the

Channel Browser banner and surf back to a previous channel or surf forward to the next channel in the channel history.

In Select mode, when you stop on a channel number in the browser banner, it will be highlighted with a yellow background but the TV will not automatically tune to the channel.

Hold HOME key 3 sec to program

Ch.3

2. Press ENTER to tune the TV to the highlighted channel.

3. Press EXIT to close the Channel Browser banner.

3 2 102-1

Select Mode

ANT 1 CABLE Ch.102-1 1080i

In Select mode, the highlighted channel number has a yellow background. Press ENTER to tune to the channel.

Hold HOME key

3 sec to program

Ch.3

Page 75

Chapter 8: Using the TV’s features

Tuning channels (continued)

Using the Channel Browser™ (continued)

Adding and clearing channels in the channel history

Adding channels to the channel history

The Channel Browser automatically creates a temporary* history of the last 32 channels that were tuned in the current input (ANT 1, ANT 2, and Cable Box inputs only). A separate

history will be stored for each of these inputs.

Note: Turning off the TV will clear the channel history for all

three inputs.

If you change the input you are viewing:

a) you will begin a channel history for that input if one had

not already been started; or

b) you will return to the existing channel history for that input

if one had already been started.

The Channel Browser will store the following channels:

• All channels that are tuned using the numeric buttons on the remote control.

• All channels that are tuned for at least 7 seconds using the CH yz buttons or the FAV CH yz buttons on the remote control.

Note:

• The Channel Browser banner will not appear when the POP double

window is open; however, channels tuned while the POP double window is open will be added to the Channel Browser history for the current input.

• The Channel Browser banner will not appear in the FAV SCAN

(favorite scan) multi-window. Channels that appear in the FAV SCAN multi-window will not be added to the Channel Browser history; however, the channel last selected from the multi-window will be added to the channel history.

Setting a channel as the “Home” channel for an input

To set a channel as Home using the remote control:

1. Tune the TV to the channel you would like to set as the Home channel for the current antenna input.

2. Press and hold the HOME (

) button on the remote control for 3 seconds. When the Home channel is saved, the Channel Browser banner will appear at the bottom of the screen with the home icon flashing green.

Note: You can set a different Home channel for each input (ANT 1, ANT 2, and Cable Box inputs only).

To set a channel as Home using the menus:

1. Press MENU and open the Preferences menu.

2. Highlight Home CH Setup and press ENTER. The Home CH Setup window will display.

Home CH Setup

ANT 1

ANT 2

Cable Box

Reset

Note: "Cable Box" will appear in the Home CH Setup window only if you connected a cable box to your TV.

Done

3. Use the y z buttons to select the input for which you want to set the Home channel.

4. Use the numeric and dash (–) buttons on the remote control to enter the desired Home channel for each input.

5. To save your entries, highlight Done and press ENTER. To clear your entries, highlight Reset and press ENTER.

Clearing channels from the channel history

• Turning off the TV will clear all three channel histories (ANT 1, ANT 2, and Cable Box).

™

• Removing the CableCARD

will clear the channel history

for the ANT 1 input.

• Reconfiguring the ANT 1, ANT 2, or Cable Box input will clear the channel history for the newly configured input(s).

Note:

See page 46 for details on configuring the antenna inputs.

To tune to the Home channel:

While an input that has a set Home channel is active, press the

HOME (

) button on the

remote control.

Note: If you press the HOME button while an input other than an antenna or Cable Box input is selected, the TV will tune to the most recently tuned Home channel and input.

x /BACK

•/NEXT

HOME ( )

Page 76

Tuning channels (continued)

Chapter 8: Using the TV’s features

Tuning your favorite channels

To tune to the channels you programmed as Favorite Channels, see page 49.

Tuning to the next programmed channel

To tune to the next programmed channel:

Press CHANNEL y or z on the remote control or TV front panel.

Note:

• This feature will not work unless you program channels into the

TV’s channel memory (see page 47).

• If you are recording a digital channel, you will only be able to

change analog channels while the recording is in progress. If you are recording an analog channel, you will only be able to change digital channels while the recording is in progress. This is because the TV tuner that is being recorded (digital or analog) will be locked on the channel that is currently recording.

Tuning to a specific channel (programmed or unprogrammed)

Tuning analog channels:

Press the Channel Number buttons (0–9) on the remote control. For example, to select channel 125, press 1, 2, 5.

Tuning digital channels:

Press the Channel Number buttons (0–9) on the remote control, followed by the – (dash) button and then the subchannel number. For example, to select digital channel 125-1, press 1, 2, 5, –, 1.

Note: If a digital channel is not programmed—either through the automatic channel scan (page 47) or the channel add/delete function (page 48)—you will have to tune the RF channel using the Channel Number and Dash buttons on the remote control.

Switching between two channels using Channel Return

The Channel Return feature allows you to switch between two channels without entering an actual channel number each time.

1. Select the first channel you want to view.

2. Select a second channel using the Channel Number buttons (and the dash (–) button if selecting a digital channel).

3. Press CH RTN on the remote control. The previous channel will display. Each time you press CH RTN, the TV will switch back and forth between the last two channels that were tuned.

Note:

• If you press CH RTN from a non-antenna input, the TV will return to the last-viewed ANT input and channel.

• If you are currently recording a program, this feature will not be available.

Switching between two channels using SurfLock™

The SurfLock™ feature temporarily “memorizes” one channel in the CH RTN button, so you can return to that channel quickly from any other channel by pressing CH RTN. To memorize a channel in the CH RTN button:

1. Tune the TV to the channel you want to program into the CH RTN button.

2. Press and hold CH RTN for about 2 seconds until the message “Channel Memorized” appears on the screen. The channel has been programmed into the CH RTN button.

3. You can then change channels repeatedly, and when you press CH RTN, the memorized channel will be selected.

The TV will return to the memorized channel one time only. Once you press CH RTN and then change channels again, the CH RTN memory will be cleared and the button will function as Channel Return, by switching back and forth between the last two channels that were tuned.

CH RTN

Channel Numbers

—

(dash)

CHANNEL yz

Page 77

Chapter 8: Using the TV’s features

Selecting the picture size

You can view many program formats in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3, and Full—as described below and on the next page.

The way the image displays in any of the picture sizes will vary depending on the format of the program you are viewing. Select the picture size that displays the current program the way that looks best to you.

Your picture size preferences can be saved for each input on your TV.

Numbers

PIC SIZE

To select the picture size:

1. Press PIC SIZE on the remote control.

2. While the Picture Size menu is on-screen, press the corresponding number button (0–4) to select the desired picture size.

Picture Size

Natural

TheaterWide 1

TheaterWide 2

TheaterWide 3

Full

PIC SIZE

- / to Select

Note:

• You also can repeatedly press PIC SIZE to select the desired

picture size (or press the yz buttons on the remote control while the Picture Size screen is open).

• “Full” may not be available for some program formats (it will

be “grayed out” in the Picture Size screen).

Natural picture size

• The image is displayed close to its originally formatted proportion. Some program formats will display with sidebars and/or bars at the top and bottom.

Natural picture size example: The way the image displays will vary depending on the format of the program you are currently watching.

Note:

You also can select the picture size using the menu system. Select Picture Size in the Video/Theater Settings menu. Select the input for which you want to save your picture settings. To save your settings, highlight Done and press ENTER.

Theater Settings

Picture Size Natural

Picture Scroll

Cinema Mode Film

Auto Aspect Ratio On

Reset

Done

Conventional picture on a conventional TV screen

Conventional picture in Natural size on your wide-screen TV

Page 78

Chapter 8: Using the TV’s features

Selecting the picture size (continued)

TheaterWide 1 picture size (For 4:3 format program)

• The center of the picture remains close to its original proportion, but the left and right edges are stretched wider to fill the screen.

TheaterWide 1 picture size example

TheaterWide 2 picture size (for letter box programs)

• The picture is stretched wider to fill the width of the screen, but only slightly stretched taller.

• The top and bottom edges of the picture are hidden. To view the hidden areas, see “Scrolling the TheaterWide

picture” on

A B C D E F G - - - - - - - - - - - - - - - -

page 79.

Note:

• If you select one of the TheaterWide® picture sizes, the top and bottom edges of the picture (including subtitles or captions) may be hidden. To view the hidden edges, either scroll the picture (TheaterWide 2 and 3 only) or try viewing the program in Full or Natural picture size.

• When selecting the picture size, the way the image displays will vary depending on the format of the program you are currently watching.

Using these functions to change the picture size (i.e., changing the height/ width ratio) for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

TheaterWide 2 picture size example

TheaterWide 3 picture size (for letter box programs with subtitles)

• The picture is stretched wider to fill the width of the screen, but only slightly stretched taller.

• The top and bottom edges are hidden. To view the hidden areas (such as subtitles or captions),

see “Scrolling the TheaterWide

picture” on

A B C D E F G - - - - - - - - - - - - - - - -

page 79.

A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -

TheaterWide 3 picture size example

Full picture size (for 16:9 [480i, 480p] source programs only)

• If receiving a squeezed 4:3 format program, the picture is stretched wider to fill the width of the screen, but not stretched taller.

• None of the picture is hidden.

Full picture size example

Page 79

Chapter 8: Using the TV’s features

Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only)

You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input.

To set the scroll settings:

1. Press INPUT on the remote control or TV/VIDEO on the TV to select the input for which you want to set the picture size and scroll settings.

2. Press MENU and open the Video menu.

3. Highlight Theater Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

Navigate

4. In the Picture Size field, select either TheaterWide 2 or TheaterWide 3 (you cannot scroll in any other mode).

5. Press z to highlight the Picture Scroll field.

6. Press x or • to scroll the picture up and down as needed, from –10 to +20.

Theater Settings

Picture Size TheaterWide 2

Picture Scroll -5

Cinema Mode Film

Auto Aspect Ratio On

Select

Back Exit

CH RTN

EXIT

DoneReset

Using the auto aspect ratio feature

When the auto aspect ratio feature is set to On, the picture size is automatically selected when one of the following input sources is received:

• A 480i signal from the VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD-1, or ColorStream HD-2 input.

• A 1080i, 480i, 480p, or 720p signal from the HDMI input.

Aspect ratio

of signal source

4:3 normal Natural (with sidebars)

4:3 letter box TheaterWide 2

16:9 full Full

Not defined

(no ID-1 data or

HDMI aspect data)

Note:

• The auto aspect ratio feature is not applicable to antenna or Cable input sources.

• The auto aspect ratio feature is not available when the POP doublewindow is open, the Freeze mode is active, or the TV Guide On Screen system is open.

To turn on the auto aspect ratio feature:

1. Press MENU and open the Video menu.

2. Highlight Theater Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

Automatic aspect size

(automatically selected

when Auto Aspect is On)

User-selected picture size

(see pages 77–78)

7. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Navigate

Select

Back Exit

CH RTN

EXIT

3. In the Auto Aspect Ratio field, select On.

Theater Settings

Picture Size Natural

Picture Scroll -1

Cinema Mode Film

Auto Aspect Ratio On

DoneReset

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

To turn off the auto aspect ratio feature:

Select Off in step 3 above.

Page 80

Chapter 8: Using the TV’s features

Selecting the cinema mode (480i signals only)

When you view a DVD (480i signal; 3:2 pulldown processed) from a DVD player connected to the VIDEO 1, VIDEO 2, ColorStream HD1/HD2 (component video), or HDMI inputs on the TV, smoother motion can be obtained by setting the Cinema Mode to Film.

To set the Cinema Mode to Film:

1. Press MENU and open the Video menu.

2. Highlight Theater Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

Navigate

3. In the Cinema Mode field, select Film.

Theater Settings

Picture Size Natural

Picture Scroll -1

Cinema Mode

Auto Aspect Ratio On

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

To set the Cinema Mode to Video:

Select Video in step 3 above.

Select

Back Exit

CH RTN

EXIT

Film

DoneReset

Selecting the lamp mode

You can select either High Bright or Low Power lamp mode.

• High Bright mode is useful when additional picture brightness is desired (such as in a bright room).

• Low Power mode reduces wear on the projection lamp. Using this mode should result in longer lamp life.

See “Lamp unit replacement and care” on page 129–131.

To select the lamp mode:

1. Press MENU and open the Video menu.

2. Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

Navigate

3. In the Lamp Mode field, select High Bright or Low Power, whichever you prefer.

Advanced Picture Settings ANT 1

Dynamic Contrast On

MPEG Noise Reduction

CableClear Off

Color Temperature Medium

Lamp Mode Low Power

Color Management

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Select

Reset

Back Exit

CH RTN

EXIT

Low

Done

Note:

If you set the lamp mode to Low Power, each time you turn on the TV, the lamp will start out in High Bright mode but will switch to Low Power mode in approximately 1 minute. You will notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction.

Page 81

Chapter 8: Using the TV’s features

Using the POP features

Using the POP double-window feature

The POP (picture-out-picture) double-window feature splits the screen into two windows so you can watch two programs at the same time.

To display a program in the POP window:

1. Select the program you want to watch in the main window.

2. Press SPLIT to open the POP double-window.

POP double-window

Main window

TV12

POPANT1

Video1

Green border (denotes active window)

POP window

Note:

• When the main window is in ANT1 or ANT2 mode, the ANT1 and ANT2 inputs cannot be selected for the POP window.

• When the main window is in Video 1, Video 2, Video 3, ColorStream HD1, ColorStream HD2, HDMI 1, or HDMI 2 mode, that same input cannot be selected for the POP window.

• You cannot view IEEE1394 source programs in the POP window.

• You cannot view two video or two antenna sources in both the main and POP windows simultaneously. (You can view a video source in one window and an antenna source in the other.)

• The FREEZE feature is not available when the POP double-window is open. If you press FREEZE when the POP double-window is open, the message “Not available” will appear.

3. Press • to highlight the POP (right) window. When highlighted, the window

will have a green border.

4. Press INPUT to open the POP Input Selection window. Select the input source for the POP window by pressing the corresponding Number button (0–9). The current source displays in purple in the POP Input Selection window.

POP Input Selection

ANT 1ANT 1

Video 1

Video 2

Video 3

ColorStream HD1

ColorStream HD2

HDMI 1

HDMI 2 PC

8 9

ANT 2

INPUT

- / to Select

Note: If you labeled all of the inputs as HIDE (page 73), the POP feature will be disabled and the message “NOT AVAILABLE” will appear on-screen if you try to open the POP double-window.

To tune to the highlighted window (and close the POP window):

Press ENTER after highlighting the window you want to view as a normal picture.

To close the POP window:

Press SPLIT or EXIT.

Notes about recording:

• If the POP window is open and you attempt to start recording, the POP window will close before recording starts.

• If you use the TV’s remote control to start recording, you will not be able to open the POP window and the message “Not Available” will appear on-screen if you try to do so.

• It is recommended that you use the TV’s remote control to start recording. If you use a device other than the TV’s remote control to start recording, you may be able to open the POP window during the recording process. If this happens, the recorded audio will reflect the audio of the active window (main or POP), which may not be the audio you intended to record.

Numbers

INPUT

•

ENTER

SPLIT

Page 82

Chapter 8: Using the TV’s features

Using the POP features (continued)

Switching the speaker audio (main or POP)

While the POP window is open, press x or • to switch the audio (main or POP) that is output from the TV speakers (and also from the VARIABLE AUDIO OUT terminals).

The window with the active sound is outlined with a green border.

Example: Press x Example: Press •

POP double-window aspect ratio

The POP double-window feature displays each picture according to its input signal aspect ratio, as illustrated in the examples below.

x •

480i 480i

480p/720p/1080i

480i

Note:

• The auto aspect ratio feature (page 79) does not operate in POP double-window mode.

• Aspect ratio is the ratio of width to height of the picture.

Page 83

Chapter 8: Using the TV’s features

Using the FREEZE feature

To use the FREEZE feature:

1. When viewing the TV, press FREEZE to make the picture a still picture.

2. To return to the moving picture, either press FREEZE again, press EXIT, or press any other button.

Note:

• The FREEZE feature is not available when the POP double-window or FAV SCAN

multi-window is open. If you press FREEZE when either window is open, the message “Not available” will appear.

• If the TV is left in FREEZE mode for more than 15 minutes, the FREEZE mode will

automatically be released and the TV will return to the moving picture.

Using the FREEZE function for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

x •

Still pictureMoving picture

Using the favorite channel scan feature

You can use this feature to quickly scan and tune the channels you programmed as favorite channels (for the ANT 1 and ANT 2 inputs only) from a nine-picture multi-window.

Note: To use the favorite channel scan feature, you must first program channels into the favorite channel memory. See “Programming your favorite channels” on page 49.

To scan and tune your favorite channels:

1. Press FAV SCAN. The TV will display the channels you programmed as favorite channels for the current ANT input in a nine-picture multi-window.

(To display the channels you programmed as favorite channels for the other ANT input, you must change antenna inputs first (page 72), and then press FAV SCAN.)

123

CABLE

456

789

2. Highlight the window for the channel you want to view: Either... Press the channel’s multi-window position number (1–9, as illustrated

above, and not the actual channel number) to highlight the window;

Or... Use the y z x • buttons to highlight the window.

The highlighted window will display as a moving picture.

3. Press ENTER to tune the TV to the highlighted channel and close the multi-window.

4–1 4–2

ENTER

EXIT

FREEZE FAV SCA N

2 4–1 4–2

Page 84

Adjusting the picture

Chapter 8: Using the TV’s features

Selecting the picture mode

You can select your desired picture settings from four different modes, as described below.

Mode Picture Quality

Sports Bright and dynamic picture (factory setting) Standard Standard picture settings (factory setting) Movie Lower contrast for darkened room (factory setting) Preference Your personal preferences

To select the picture mode using the remote control:

Press PIC MODE on the remote control. The following popup menu appears on-screen.

Picture Settings Mode: Standard

Mode Standard

Repeatedly press PIC MODE to cycle among the modes or use x or • to select the picture mode you prefer.

To select the picture mode using the menu system:

1. Press MENU and open the Video menu.

2. Highlight Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. In the Mode field, select the picture mode you prefer.

Picture Settings

Mode Sports

Contrast 100

Brightness

Color

Tint

Sharpness

Picture Settings Mode: Standard

Mode Standard

Reset

Done

ANT 1

PIC

MODE

Adjusting the picture quality

You can adjust the picture quality (contrast, brightness, color, tint, and sharpness) to your personal preferences.

Selection x Pressing •

contrast lower higher brightness darker lighter color paler deeper tint reddish greenish sharpness softer sharper

To adjust the picture quality:

1. Press MENU and open the Video menu.

2. Highlight Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. Press y or z to select the picture quality you want to adjust

(contrast, brightness, color, tint, or sharpness), and then x and • to adjust the setting, as described in the table above.

Picture Settings

Mode Sports

Contrast 100

Brightness

Color

Tint

Sharpness

Picture Settings Mode: Preference

Contrast 70

Reset

Done

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

The picture qualities you adjusted are automatically saved in the Preference mode (see “Selecting the picture mode,” above left).

ANT 1

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Note:

• The picture mode you select affects the current input only

(ANT 1 in the example above). You can select a different picture mode for each input.

• If you select one of the factory-set picture modes (Sports,

Standard, or Movie) and then change a picture quality setting (for example, increase the contrast or change the color temperature), the picture mode automatically changes to Preference in the Picture Settings menu.

Page 85

Chapter 8: Using the TV’s features

Adjusting the picture (continued)

Using the Color Management feature

The Color management feature allows you to adjust the hue and saturation of six colors: red, green, blue, yellow, magenta, and cyan.

To change the Color Management settings:

1. Press Menu and open the Video menu.

2. Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. Highlight Color Management and press ENTER.

Advanced Picture Settings ANT 1

Dynamic Contrast On

MPEG Noise Reduction

CableClear Auto

Color Temperature Cool

Lamp Mode Low Power

Color Management

Reset

Low

Done

4. In the Color Management field, select On.

6. Press y or z to select either Hue or Saturation, and then press x and • to adjust the setting.

Hue +2

Saturation +2

7. Press ENTER to return to the Color Management window.

8. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Note:

• If you select Off in step 4 above, you cannot adjust the Hue

or Saturation.

• If you select one of the factory-set picture modes (Sports,

Standard, or Movie) and then change the Color Management to “On,” the picture mode automatically changes to Preference in the Picture Settings menu (page 84).

5. Press y or z to highlight the color you want to adjust,

and then press ENTER.

Color Management

Color Management On

Red

Green

Blue

Yellow

Magenta

Cyan

Reset

Hue Saturation –15

–15

+15

Done

Page 86

Chapter 8: Using the TV’s features

Adjusting the picture (continued)

Using CableClear®/DNR (digital noise reduction)

The CableClear® digital noise reduction feature allows you to reduce visible interference in your TV picture. This may be useful when receiving a broadcast with a weak signal (especially a Cable channel) or playing a noisy video cassette or disc. This feature is enabled for 480i signals only.

Note: The CableClear DNR feature does not function in ColorStream, HDMI (DVI), ATSC, IEEE1394, or digital Cable mode.

To change the CableClear/DNR settings:

1. Press MENU and open the Video menu.

2. Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. In the CableClear/DNR field, select your desired setting.

Advanced Picture Settings ANT 1

Dynamic Contrast On

MPEG Noise Reduction

CableClear Auto

Color Temperature Cool

Lamp Mode Low Power

Color Management

Reset

Note:

• If the current input is ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3, the menu will display the text “CableClear.” The available selections are Off, Low, Middle, High, and Auto.

• If the current input is ColorStream HD1, ColorStream HD2, or HDMI, and the video resolution is 480i, the menu will display the text “DNR.” The available selections are Off, Low, Middle, High, and Auto. Auto will react proportionally to the strength of the noise. Low, Middle, and High will reduce the noise in varying degrees, from lowest to highest, respectively.

• If the current input is ColorStream HD1, ColorStream HD2, or HDMI, and the video resolution is not 480i, the menu will display the text “DNR”.

Low

Done

Selecting the color temperature

You can change the quality of the picture by selecting from three preset color temperatures (cool, medium, and warm), as described below.

Mode Picture Quality

cool blueish medium neutral warm reddish

To select the color temperature:

1. Press MENU and open the Video menu.

2. Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. In the Color Temperature field, select the mode you prefer (Cool, Medium, or Warm).

Advanced Picture Settings ANT 1

Dynamic Contrast On

MPEG Noise Reduction

CableClear Auto

Color Temperature Cool

Lamp Mode Low Power

Color Management

Reset

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Note:

If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then change the color temperature mode, the picture mode automatically changes to Preference in the Picture Settings menu.

Low

Done

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Page 87

Chapter 8: Using the TV’s features

Adjusting the picture (continued)

Using MPEG noise reduction

The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are High, Medium, Low, and Off. Off is automatically selected when this feature is disabled (“grayed out”). This feature is not available in the PC input mode.

To select the MPEG noise reduction level:

1. Press MENU and open the Video menu.

2. Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. Press y or z to highlight the MPEG Noise Reduction field, and then press x or • to select either High, Middle, Low, or Off.

Advanced Picture Settings ANT 1

Dynamic Contrast On

MPEG Noise Reduction

CableClear Auto

Color Temperature Cool

Lamp Mode Low Power

Color Management

Reset

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Low

Done

Using dynamic contrast

When dynamic contrast is set to “On,” the TV will detect changes in the picture quality that affect the appearance of your contrast settings and then automatically adjust the video.

When dynamic contrast is set to “Off,” the settings selected in the Contrast field in Picture Settings will be used.

To select dynamic contrast preferences:

1. Press MENU and open the Video menu.

2. Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. In the Dynamic Contrast field, select either On or Off.

Advanced Picture Settings ANT 1

Dynamic Contrast On

MPEG Noise Reduction

CableClear Auto

Color Temperature Cool

Lamp Mode Low Power

Color Management

Reset

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Note:

If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then set the dynamic contrast to “On,” the picture mode will automatically change to Preference in the Picture Settings menu.

Low

Done

Page 88

Chapter 8: Using the TV’s features

Using the closed caption mode

The closed caption mode has two options:

• Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked “CC” in program guides).

• Text—An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations).

To view captions or text:

1. Press MENU and open the Preferences menu.

2. Highlight Closed Caption Mode and then press •.

3. Press z or y to select the desired closed caption mode and

press ENTER.

Preferences

Favorite Channels

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language

Home CH Setup

Navigate

English

Select

Off

CH RTN

Off

CC1

CC2

CC3

CC4

Back Exit

EXIT

• To view captions:

Highlight CC1, CC2, CC3, or CC4. (CC1 displays translation of the primary language in your area.)

Note: If the program or video you selected is not closed captioned, no captions will display on-screen.

Giant pandas eat leaves.

• To view text:

Highlight T1, T2, T3, or T4.

Note: If text is not available in your area, a black rectangle may appear on your screen. If this happens, turn off the Closed Caption Mode.

WORLD WEATHER

Temps Current F C Weather LONDON 51 11 MOSCOW PARIS ROME TOKYO

57 14 53 12 66 19 65 18

Clear Cloudy Clear Cloudy Rain

Advanced closed captions

You can customize the closed caption display characteristics by changing the text size, type, edge, color, and the background color.

Note:

• This feature is available for digital channels only.

• You cannot set the Caption Text and Background as the same color.

To customize the closed captions:

1. Press MENU and open the Preferences menu.

2. Highlight Closed Caption Advanced and press ENTER.

3. Press y or z to highlight the characteristic you want to change, and then press x or to select the format for that characteristic.

4. To save the

•

Advanced Closed Captions

Caption Size Auto

Caption Text Type

Caption Text Edge

Caption Text Color

Background Color

new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Caption Size

Caption Text Type

Caption Text Edge

Caption Text Color

Background Color

Auto, Small, Standard, Large

Auto, Default, Mono w. Serif, Prof. w. Serif, Mono w/o Serif, Prop w/o Serif, Casual, Cursive, Small Capitals

Auto, None, Raised, Depressed, Uniform, Left Drop Shadow, Right Drop shadow

Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan

Preferences

Favorite Channels

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language

Home CH Setup

Navigate

Select

Reset

CC1

English

Done

Back Exit

CH RTN

Auto

EXIT

• To turn off the Closed Caption mode:

Select Off in step 3 above.

Note: A closed caption signal may not display in the following situations:

• When a videotape has been dubbed

• When the signal reception is weak

• When the signal reception is non-standard

Page 89

Chapter 8: Using the TV’s features

Using the closed caption mode (continued)

Digital closed captions

You can use the Digital CC/Audio selector to select digital closed caption services (if available), which will temporarily override closed captions for digital channels only.

When such services are not available, the Digital CC/Audio selector presents a default list of services. If the selected service is not available, the next best service will be used instead.

To select digital closed captions:

1. Press MENU and open the Applications menu.

2. Highlight Digital CC/Audio Selector and press ENTER.

Applications

TV Guide On Screen

Audio Player

Picture Viewer

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTN

EXIT

3. Press y or z to select Closed Caption, and then press x or • to select the desired service.

CC 1Audio

Closed Caption

Service 1

4. Press ENTER.

Page 90

Adjusting the audio

Chapter 8: Using the TV’s features

Muting the sound

Press MUTE to partially reduce (1/2 MUTE) or turn off (MUTE) the sound. Each time you press MUTE, the mute mode will change in the following order:

→ 1/2 Mute → Mute → Volume →

If the closed caption mode is set to Off when you select “MUTE” mode, the closed caption feature is automatically activated. To mute the audio without automatically activating the closed caption feature, use the VOL z button to set the volume to 0. See “Using the closed caption mode” on page 88 for more information on closed caption modes.

VOL z

RECALL MUTE

Using the digital audio selector

You can use the Digital CC/Audio selector to conveniently switch between audio tracks on a digital channel (for those channels that have multiple audio tracks). This temporarily overrides the audio track chosen by the language option under Audio Setup (see “Selecting stereo/SAP broadcasts,” at right).

To use the digital audio selector:

1. Press MENU and open the Applications menu.

2. Highlight Digital CC/Audio Selector and press ENTER.

Applications

TV Guide On Screen

Audio Player

Picture Viewer

Digital CC/Audio Selector

CableCARD

Navigate

3. Press y or z to select Audio, and then press x or • to select the desired service.

Closed Caption

4. Press ENTER.

Select

Back Exit

CH RTN

EXIT

CC 1Audio

Service 1

Selecting stereo/SAP broadcasts

The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music, or other audio information (when provided by individual stations).

The MTS feature is not available when the TV is in VIDEO mode. When the TV receives a stereo or SAP broadcast, the word “STEREO” or “SAP” appears on-screen when RECALL is pressed.

To listen to stereo sound:

1. Press MENU and open the Audio menu.

2. Highlight Audio Setup and press ENTER.

3. In the MTS field, select Stereo.

4. To save the new settings, highlight Done and press ENTER. To reset the settings to the factory defaults, highlight Reset and press ENTER.

Note:

• If you leave the TV in Stereo mode it will automatically output the

type of sound being broadcast (stereo or monaural).

• If the stereo sound is noisy, select MONO to reduce the noise.

To listen to an alternate language on an ATSC digital station (if available):

Highlight the Language field in step 3 above, and then press x or • to select the language you prefer.

To listen to a second audio program on an analog station (if available):

Select SAP in step 3 above.

Note:

• A second audio program (SAP) can be heard only on TV stations that offer it. For example, a station might broadcast another language as a second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program’s normal audio.

• If you have SAP on and the station you are watching is not broadcasting a second audio program, the station’s normal audio will be output. However, occasionally there is no sound at all in SAP mode. If this happens, set the MTS feature to Stereo mode.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

MTS

Language

Speakers On

Optical Output Format Dolby Digital

Reset

Done

Stereo

English

Page 91

Chapter 8: Using the TV’s features

Adjusting the audio (continued)

Adjusting the audio quality

You can adjust the audio quality by adjusting the bass, treble, and balance.

To adjust the audio quality:

1. Press MENU and open the Audio menu.

2. Highlight Audio Settings

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

and press ENTER.

3. Press zor the item you want to adjust

y to highlight

Navigate

Select

Back Exit

CH RTN

EXIT

(bass, treble, or balance).

Audio Settings

Bass 100

Treble

Balance

SBS

SBS Level

StableSound Off

Reset

100

Done

4. Press x or • to adjust the level.

• x

makes the bass or treble weaker or increases the balance

in the left channel (depending on the item selected).

• •

makes the bass or treble stronger or increases the balance

in the right channel (depending on the item selected).

5. To save the new settings, highlight Done and press ENTER. To reset the settings to the factory defaults, highlight Reset and press ENTER.

Using the sub-bass system (SBS)

The sub-bass system allows you to enhance bass performance, even when the volume is low.

To turn on the SBS and adjust the level:

1. Press MENU and open the Audio menu.

2. Highlight Audio settings and press ENTER.

3. In the SBS field, select On.

4. Press y or z to highlight SBS Level, and then press x or • to adjust the sub-bass system.

Audio Settings

Bass 100

Treble

Balance

SBS

SBS Level

StableSound Off

Reset

100

Done

Using the StableSound® feature

The StableSound® feature limits the highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial).

Back Exit

EXIT

Done

feature:

To turn on the StableSound

1. Press MENU and open the Audio menu.

2. Highlight Audio Settings and press ENTER.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

Navigate

Select

CH RTN

3. In the StableSound field, select On.

Audio Settings

Bass 100

Treble

Balance

SBS

SBS Level

StableSound On

Reset

100

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Note: The RESET function returns your audio adjustments to the following factory settings:

Bass ............. center (50)

Treble .......... center (50)

Balance ........ center (0)

StableSound... Off

To turn off the StableSound feature:

Select Off in step 3 above.

5. To save the new settings, highlight Done and press ENTER. To reset the settings to the factory defaults, highlight Reset and press ENTER.

To turn off the SBS:

Select Off in step 3.

Page 92

Chapter 8: Using the TV’s features

Adjusting the audio (continued)

Using the SRS™ WOW™ surround sound feature

WOW™ is a special combination of SRS Labs audio technologies (SRS 3D, FOCUS, and TruBass) that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer, and wider.

Reset

™

settings:

Off

Done

To adjust the WOW

1. Put the TV in STEREO mode (see “Selecting stereo/SAP broadcasts” on page 90).

2. Press MENU and open the Audio menu.

3. Highlight Advanced Audio Settings and press ENTER.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

4. Press z or y to highlight the WOW feature you want to adjust, and then press x or • to adjust the item.

Advanced Audio Settings

WOW: SRS 3D

WOW: FOCUS

WOW: TruBass Low

Dolby Virtual TruSurround

• WOW: SRS 3D — To turn the surround sound effect

On or Off.

Note: If the broadcast is monaural, the SRS 3D effect will not work.

• WOW: Focus — To turn the vocal emphasis effect On

or Off.

• WOW: TruBass — To select the desired bass expansion

level (High, Low, or Off).

Using the virtual surround sound

feature (Dolby

The Dolby* Virtual/TruSurround feature allows you to enjoy virtual surround sound from the TV’s speakers. This feature is enabled only when the TV is receiving digital broadcasts.

To turn on the Dolby Virtual/TruSurround feature:

1. Press MENU and open the Audio menu.

2. Highlight Advanced Audio Settings and press ENTER.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

3. In the Dolby Virtual/TruSurround field, select On.

Advanced Audio Settings

WOW: SRS 3D

WOW: FOCUS

WOW: TruBass Low

Dolby Virtual TruSurround

Reset

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

To turn off theDolby Virtual/TruSurround feature:

Select Off in step 3 above.

Note: The Dolby Virtual/TruSurround and WOW SRS 3D features cannot be on at the same time. If you set one to On, the other will automatically be set to Off.

Virtual/TruSurround™)

Off

Done

5. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

_________

WOW, TruSurround, SRS and symbol are trademarks of SRS Labs, Inc.

WOW technology is incorporated under license from SRS Labs, Inc. TruSurround technology is incorporated under license from SRS Labs, Inc.

*Manufactured under license from Dolby Laboratories. Dolby is a registered trademark of Dolby Laboratories.

Page 93

Chapter 8: Using the TV’s features

Adjusting the audio (continued)

Turning off the built-in speakers

You can use this feature to turn off the TV speakers when you connect an audio system to your TV (see “Connecting a digital audio system” and “Connecting an analog audio system” on page 24).

To turn off the built-in speakers:

1. Press MENU and open the Audio menu.

2. Highlight Audio Setup and press ENTER.

3. In the Speakers field, select Off.

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

To turn on the built-in speakers:

Select On in step 3 above.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

MTS

Language

Speakers On

Optical Output Format Dolby Digital

Reset

Done

Stereo

English

Selecting the optical audio output format

You can use this feature to select the optical audio output format when you connect a Dolby Digital decoder or other digital audio system to the Optical Audio Out terminal on the TV (see “Connecting a digital audio system” on page 24).

To select the optical audio output format:

1. Press MENU and open the Audio menu.

2. Highlight Audio Setup and press ENTER.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

3. In the Optical Output Format field, select either Dolby Digital or PCM, depending on your device.

Audio Setup

MTS

Language

Speakers On

Optical Output Format

Reset

Stereo

English

Dolby Digital

Done

4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Page 94

Chapter 8: Using the TV’s features

Setting the On/Off Timer

You can use the On/Off Timer to turn the TV on and off at a preset time on a recurring basis.

Note: You must first set the time (see page 55).

To set the On/Off Timer:

1. Press MENU and open the Setup menu.

2. Highlight On/Off Timer and press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

3. In the DAY field, press x or • to select the recurrence

(weekends, weekdays, every day, etc).

On/Off Timer

Turn TV ON:

Day

Time (HH:MM)

TV ON Duration:

Reset DoneCancel

4. Press z to highlight the Time field, and then use the

Number buttons to enter the time you want the TV to turn on.

5. When the AM/PM field is highlighted, press • to select

AM or PM.

6. Press z to highlight the TV ON Duration field, and then press x or • to select the length of time until the TV turns off (30 Minutes, 12 Hours, 8 Hours, 4 Hours, 2 Hours, 1 Hour).

7. Highlight Done and press ENTER.

8. Turn off the TV. The TV will turn on automatically on the day(s) and at the time you set. The TV will then turn off automatically after the length of time you set in the TV ON Duration field.

Note:

• When a power failure occurs, the On/Off Timer settings may

be cleared.

• To display the On/Off Timer setting, press RECALL.

To turn off the On/Off Timer:

Select Not Set in step 3 above.

On/Off Timer

Turn TV ON:

Day

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

Weekends

09 00 AM

30 Minutes

Not Set

Setting the sleep timer

You can set the sleep timer to turn off the TV after a set length of time (maximum of 3 hours).

The sleep timer turns off the TV one time only, as opposed to the On/Off Timer, which turns off the TV on a recurring basis.

To set the sleep timer:

Press SLEEP on the remote control to set the length of time until the TV turns off. Repeatedly press SLEEP to increase the time in 10-minute increments or press y or z to increase or decrease the time in 10-minute increments, to a maximum of 3 hours and 00 minutes.

To cancel the sleep timer:

Press SLEEP until it is set to 0.

SLEEP

To set the sleep timer using the on-screen menus:

1. Press MENU and open the Setup menu.

2. Highlight Sleep Timer and press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

3. Press the Number buttons to enter the length of time in 10-minute increments.

Sleep Timer

Enter total minutes until the TV

turns off automatically (Maximum

180 minutes)

Cancel

4. Highlight Done and press ENTER.

Note:

• When a power failure occurs, the sleep timer setting may be cleared.

• To display the amount of time left on the sleep timer, press RECALL.

To display the remaining sleep time:

Press SLEEP.

Sleep Timer

1h10m

1 2 0

Select

2 Sec

Done

Auto

Back Exit

CH RTN

EXIT

Reset DoneCancel

Note:

A message will display on-screen when there is one minute remaining on the sleep timer.

Page 95

Chapter 8: Using the TV’s features

Using the PC settings feature

You can view the image from a PC on the TV screen. The PC must be connected to the TV’s PC IN terminals. (See page 29 for connection details.)

You can use the PC Settings feature to adjust the picture’s horizontal position/size, vertical position/size, clock phase, and sampling clock.

Note: If a PC is not connected, this feature will be grayed out in the Input Selection screen and Setup menu.

To adjust the PC settings:

1. Repeatedly press INPUT to select “PC” input mode. (See “Selecting the video input source to view” on page 72.)

2. Press MENU and open the Setup menu.

3. Highlight PC Settings and press ENTER.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

Back Exit

CH RTN

EXIT

4. Press y or z to highlight the item you want to adjust.

5. Press x or • to make the appropriate adjustments.

• Horizontal Position:

Moves the picture left/right. The adjustment range is within ±5 from center.*

• Vertical Position:

Moves the picture up/down. The adjustment range is within ±5 from center.*

• Horizontal Width:

Adjusts the width of the picture. The adjustment range is within ±5 from center.*

• Vertical Height:

Adjusts the height of the picture. The adjustment range is within ±5 from center.*

• Clock Phase:

Helps to reduce noise and sharpen the picture. The adjustment range is within ±15 from center.*

• Sampling Clock:

Helps to minimize periodic vertical stripes on the screen. The adjustment range is within ±15 from center.*

___________

*The range of adjustment may vary slightly.

PC Settings

Horizontal Position 0

Horizontal Width 0

Vertical Position

Vertical Height

Clock Phase

Sampling Clock

Reset

Done

Page 96

Chapter 8: Using the TV’s features

Displaying TV setting information on-screen using RECALL

To display TV setting information on-screen:

Press RECALL on the remote control. The following information will display on-screen (if applicable):

• Current input (ANT 1, ANT 2, VIDEO 1, etc.)

• If ANT 1 or ANT 2 is the current input, whether it is

Cable TV (“CABLE”) or off-air (“TV”)

• Channel number (if in ANT 1 or ANT 2 mode)

• Signal strength indicator (bar graph in lower right corner of screen; for ATSC signal only)

Note: The signal strength indicator will react to fading and increasing signals.

• Time (if set)

• On/Off timer settings (if set)

• Remaining time on sleep timer (if set)

• Remaining time on game timer (if set)

• Stereo or SAP audio status

• V-Chip rating status

• Picture size

• Tuner hold* (if applicable)

*If you are recording on one tuner (for example, the digital tuner), you will be able to change channels on the other tuner only (the analog tuner in this example). The tuner from which you are recording is “on hold” (i.e., locked) so your recordings will not be affected by channel changes.

• Video resolution

• Lamp mode (appears only if the TV is in Hi Bright mode)

STEREO T uner Hold: On

NC-17 On Timer: Weekdays 12:00pm Sleep Timer: 18 min.

Game Timer: 28 min.

Natural 1080i

5:32pm CABLE

81-1

Sample RECALL screen

Understanding the auto power off feature

The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This feature functions in ANT 1 and ANT 2 modes only.

Understanding the last mode memory feature

ANT 1

If the power is cut off while you are viewing the TV, the Last Mode Memory feature automatically turns on the TV when the power is resupplied.

Note: You should unplug the TV’s power cord if it is possible that you will be away from the TV for an extended period of time after the power is restored.

Using the Gray Level feature

The gray level feature will set the sidebars to three different levels of darkness. Sidebars are the blanks spaces on either side of a 4:3 viewing area.

To set the gray level of the sidebars:

1. Press MENU and open the Setup menu.

2. Highlight Gray Level and press •.

3. Press y or z to select your desired level of darkness

(1 – Black, 2 – Dark Gray or 3 – Gray).

To close the RECALL screen:

Press RECALL again.

Setup

PC Settings

HDMI 1 Audio

HDMI 2 Audio

Slide Show Interval

AVHD Skip Time

Gray Level

Quick Restart

Navigate

Note:

• The gray level feature does not affect video being viewed in 16:9 aspect ratio.

• When receiving a signal that has sidebars (e.g., 4:3 aspect ratio video over a 1080i or 720p signal), the gray level feature will not be applied to the sidebars.

Select

Auto

2 Sec

15 min

Back Exit

CH RTN

EXIT

Page 97

Using the Locks menu

The Locks menu includes the Enable Rating Blocking, Edit Rating Limits, Channels Block, Input Lock, Front Panel Lock, Game Timer, and New PIN Code features. You can use these features after entering the correct PIN code.

Entering the PIN code

1. Press MENU and highlight the Locks menu icon.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

2. Press z, which displays the PIN code entry screen.

• The Lock System screen (below) appears if a PIN code has not been stored. Press the Channel Number buttons to enter a new four-digit code, enter the code a second time to confirm, and press ENTER.

Lock System

Please enter a 4 digit PIN code

Confirm PIN code

Cancel

Select

Off

Back Exit

CH RTN

Done

EXIT

If you cannot remember your PIN code

While the PIN code entering screen is displayed, press RECALL four times within five seconds. The PIN code will be cleared and you can enter a new PIN code.

Changing your PIN code

1. Press MENU and highlight the Locks menu icon.

2. Press z to display the PIN code entering screen.

3. Enter your four-digit PIN code and press ENTER.

4. Press z to highlight New PIN Code and press ENTER.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

EXIT

• The Locks/Active screen (below) appears if the PIN code is already stored. Use the Channel Number buttons to enter your four-digit code and press ENTER.

Locks Active

Please enter the 4 digit PIN code

****

Cancel

Done

If the wrong PIN code is entered, the message “Incorrect PIN code, please try again!” appears. Highlight Retry and press ENTER. Enter the code again and press ENTER.

When the correct PIN code is entered, the Locks menu opens.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

EXIT

5. Press the Number buttons to enter a new four-digit code. Retype the numbers to confirm the PIN code you entered.

6. Press ENTER. The new PIN code is now active.

New PIN Code

Please enter a 4 digit PIN code

****

Confirm PIN code

****

Cancel

Done

Page 98

Chapter 9: Using the Locks menu

Blocking TV programs and movies by rating (V-Chip)

Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language). The V-Chip feature in this TV detects the signals and blocks the programs according to the ratings you select. (See the tables at right for rating descriptions.)

Note: Rating blocking is a function of the V-Chip feature in this TV, which supports the U.S. V-Chip system only.

To block and unblock TV programs and movies:

1. Press MENU and highlight the Locks menu icon.

2. Press z to display the PIN code entering screen.

3. Enter your four-digit PIN code and press ENTER.

4. Press z to highlight Enable Rating Blocking.

5. Press • and then z to select On, and then press ENTER.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

Off

EXIT

6. Press z to highlight Edit Rating Limits and press ENTER.

Independent rating system for broadcasters

Ratings Description and Content themes

TV-MA Mature Audience Only (This program is specifically designed

to be viewed by adults and therefore may be unsuitable for children under 17.)

L) Crude or indecent language S) Explicit sexual activity V) Graphic violence

TV-14 Parents Strongly Cautioned (This program contains some

material that many parents would find unsuitable for children under 14 years of age.)

D) Intensely suggestive dialog L) Strong, coarse language S) Intense sexual situations V) Intense violence

TV-PG Parental Guidance Suggested (This program contains

material parents may find unsuitable for younger children.)

D) Some suggestive dialog L) Infrequent coarse language S) Some sexual situations V) Moderate violence

TV-G General Audience (Most parents would find this program

suitable for all ages.)

TV-Y7, Directed to Older Children (This program is designed

TV-Y7FV for children age 7 and above. Note: Programs in which

fantasy violence may be more intense or more combative than other programs in this category are designated Y7FV.)

TV-Y All Children (This program is designed to be appropriate for

all children.)

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

EXIT

The Edit Rating Limits screen (below) appears.

7. Press yzx • and then press ENTER to select the level of

blocking you prefer. A box with an “×” is a rating that will be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen.

8. When you are finished selecting the ratings you want to block, highlight Done and press ENTER.

Independent rating system for movies

Rating Description and content themes

X X-rated (For adults only)

NC-17 Not intended for anyone 17 and under

R Restricted (Under 17 requires accompanying parent or adult)

PG-13 Parents Strongly Cautioned (Some material may be

inappropriate for children under 13)

PG Parental Guidance Suggested (Some material may not be

suitable for children)

G General Audience (Appropriate for all ages)

Note:

• If you place an “X” in the box next to “ ‘None’ Rated,” programs rated “None” will be blocked; however, programs that do not provide any rating information will not be blocked.

• To display the rating of the program you are watching, press RECALL on the remote control. If it is rated “None,” the word “NONE” appears in the RECALL screen (as shown below right). If rating information is not provided, no rating will appear in the RECALL screen.

TV PG L V– NONE

Page 99

Chapter 9: Using the Locks menu

Blocking channels

With the Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you clear the setting first.

To block channels:

1. Press MENU and highlight the Locks menu icon.

2. Press z to display the

PIN code entering screen.

3. Enter your four-digit PIN code and press ENTER (see page 97 for details).

4. Press z to highlight Channels Block and then press ENTER.

5. Using the yz x • buttons, select the input for which you want to change the rating limits (ANT1, ANT2, or Cable Box, if connected) and press ENTER.

A list of the channels available for that input will be displayed along with the call letters for each channel, if available.

6. Press yz to highlight the channel you want to block, then press ENTER, which puts an “×” in the box next to that channel.

7. Repeat step 6 for other channels you want to block.

8. Highlight Done and press ENTER.

To unblock individual channels:

In step 6 above, press yz to highlight the channel you want to unblock, and then press ENTER to remove the “X” from the box, and then highlight Done and press ENTER.

To block all channels at once:

Highlight Block All in step 6 above, and then highlight Done, and press ENTER.

To unblock all locked channels at once:

Highlight Allow All in step 6 above, and then highlight Done and press ENTER.

Note: Channel blocking may not take effect if you have a cable box connected and use the cable box controls to change channels.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Channels Block

Select

Off

Back Exit

CH RTN

EXIT

ANT 1

ANT 2

Cable Box

Allow All

Block All

Cancel

Done

ANT 1

ANT 2

Cable Box

Allow All

Block All

Cancel

Done

Unlocking programs temporarily

If you try to tune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will appear on-screen:

You can either temporarily unlock the program or select an unlocked program to watch.

To temporarily unlock the program:

1. Press MUTE.

2. Enter your four-digit PIN code and press ENTER. If the correct code is entered, the

Locks Active

Enter PIN code to temporaily un-

Cancel

block.

****

Done

program lock mode is released and the normal picture appears. All locking is disabled until the TV is turned off, and will be enabled when the TV is turned on again.

Using the input lock feature

You can use the Input Lock feature to lock the video inputs (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD-1, ColorStream HD-2, HDMI 1, HDMI 2, and PC) and channels 3 and 4. You will not be able to view the input sources or channels until you unlock the inputs.

To lock/unlock the video inputs:

1. Press MENU and highlight the Locks menu icon.

2. Press z to display the PIN code entering screen.

3. Enter your four-digit PIN code and press ENTER.

4. Press z to highlight Input Lock and press •.

5. Press y or z to select the level of video input locking you prefer, as described below.

6. Press ENTER. Video: Locks VIDEO 1, VIDEO 2, VIDEO 3,

ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2, and PC.

Video+: Locks VIDEO 1, VIDEO 2, VIDEO 3,

ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2, PC, and channels 3 and 4.

• Make sure the POP window is not on channel 3 or 4.

• Select Video+ if you play video tapes via an ANT input.

• When a CableCARD™ is inserted, Video+ will not lock channels 3 and 4.

Off: Unlocks all video inputs and channels 3 and 4.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

Off

Video

Video +

EXIT

Page 100

Chapter 9: Using the Locks menu

Using the GameTimer™

You can use the GameTimer to set a time limit for playing a video game (30–120 minutes). When the GameTimer is activated, the TV enters VIDEO LOCK mode and locks out the input source for the video game device.

To set the GameTimer™:

1. Press MENU and highlight the Locks menu icon.

2. Press z to display the PIN code entering screen.

3. Enter your four-digit PIN code and press ENTER.

4. Press z to highlight Game Timer and then press •.

5. Press y or z to select the length of time until the Video

Lock is activated (30, 60, 90, or 120 minutes) and press ENTER.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

Off

30 min

60 min

90 min

120 min

EXIT

Using the front panel lock feature

You can lock the front panel touchpad controls to prevent your settings from being changed accidentally (by children, for example). When the front panel lock is On, none of the controls on the TV front touchpad will operate except POWER.

To lock the front panel:

1. Press MENU and highlight the Locks menu icon.

2. Press z to display the PIN code entering screen.

3. Enter your four-digit PIN code and press ENTER.

4. Press z to highlight Front Panel Lock.

5. Press • to highlight On and press ENTER. When the front

panel is locked and any button on the touchpad (except POWER) is pressed, the message “Not Available” appears.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock Off

Front Panel Lock

Game Timer

New PIN Code

Navigate

Select

Off

Back Exit

CH RTN

Off

EXIT

To cancel the GameTimer™:

Select Off in step 5 above.

To deactivate the video lock once the GameTimer has activated it:

Set the VIDEO LOCK to Off (see “Locking video inputs” on page 99).

Note:

• A message will appear on-screen when 10 minutes, 3 minutes, and 1 minute remain on the GameTimer.

• If the TV loses power with time remaining on the GameTimer, when power is restored the TV will enter VIDEO LOCK mode (as if the GameTimer had expired) and you will have to deactivate the video lock (as described above).

To unlock the front panel:

Highlight Off in step 5 above, or press and hold the VOLUME x button on the TV front panel for about 10 seconds until the volume icon appears on-screen.

TV front panel touchpad

VOLUME x

100

Toshiba 62HMX95, 52HMX95 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual