Toshiba DLPTM, 62HM14 User Manual

OWNER'S MANUAL

DLPTM Projection Television

Introduction

your TV

Connecting

Using the

Remote Control

Owner's Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

your TV

Setting up

Features

Using the TV’s

Appendix

62HM14

62HM14(E)01 1/24/05, 8:55 PM1

Model:

Serial No.:

Index

23566611

Dear Customer,

Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV. Before operating the TV, please read this manual completely, and keep it nearby for future reference.

Safety Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAI N OR MOISTURE.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

NOTICE OF POSSIBLE TV STAND INSTABILITY

CAUTION: This television is for use only with the Toshiba stand listed below. Use with other

carts or stands is capable of resulting in instability

and causing possible injury.

Television Stand Model

62HM14 ST6214, ST6284, or ST6294

NOTE TO CATV INSTALLERS IN THE U.S.A.

This is a reminder to call the CATV system installer’s attention to Article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 27 and 28 on page 4.

The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. DO NOT TRY TO SERVICE THIS PRODUCT YOURSELF.

The exclamation mark in the triangle tells you that important operating and maintenance instructions follow this symbol.

Lamp Unit Replacement

CAUTION: HOT SURFACE! The temperature of the lamp immediately after use exceeds 392°F (200°C).

cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

The lamp in this product has a limited service life. The length of service life varies depending on product use and user settings. If you use the lamp beyond its service life:

• you may notice a reduction in the colors and/or brightness of the picture, at which time you should replace the lamp unit; and

• the strength of the quartz glass in the lamp will be reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

Note: The lamp unit is designed so broken lamp glass remains securely inside the lamp unit.

See “Appendix” on pages 56–59.

• Dispose of the used lamp unit by the approved method for your area.

disposal or recycling information, contact your local authorities or the Electronics Industries Alliance (www.eiae.org).

Touching the lamp before it has

Note:

The lamp unit contains mercury. Disposal of mercury

may be regulated due to environmental considerations. For

ENERGY STAR® qualified TV. Products that earn the ENERGY STAR prevent green house gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy. ENERGY STAR and the ENE RGY STAR mark are registered U.S. marks.

NOTE: NEVER CONNECT THI S TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

Child Safety

It Makes A Difference Where Your TV Stands

Congratulations on your purchase! As you enjoy your new TV, keep these safety tips in mind:

The Issue

 If you are like most consumers, you have a TV in your home. Many homes,

in fact, have more than one TV.

 The home theater entertainment experience is a growing trend, and larger

TVs are popular purchases; however, they are not always supported on the proper TV stands.

 Sometimes TVs are improperly secured or inappropriately

situated on dressers, bookcases, shelves, desks, audio speakers,

chests, or carts. As a result, TVs may fall over, causing

unnecessary injury.

We Care!

 The consumer electronics industry is committed to making home entertainment enjoyable and safe.

 The Consumer Electronics Association formed the

Home Entertainment Support Safety Committee, comprised

of TV and consumer electronics furniture manufacturers, to

advocate children’s safety and educate consumers and their

families about television safety.

Tune Into Safety

 One size does NOT fit all! Use appropriate furniture large enough to

support the weight of your TV (and other electronic components).

 Use appropriate angle braces, straps, and anchors to secure your furniture

to the wall (but never screw anything directly into the TV).

 Carefully read and understand the other enclosed instructions for proper

use of this product.

 Do not allow children to climb on or play with furniture and TVs.  Avoid placing any item on top of your TV (such as a VCR, remote control,

or toy) that a curious child may reach for.

 Remember that children can become excited while watching a program

and can potentially push or pull a TV over.

 Share our safety message about this hidden hazard of

your family and friends. Thank you!

2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org

CEA is the Sponsor, Producer and Manager of the International CES

the home with

62HM14(E)02-05 1/24/05, 9:42 PM2

Important Safety Instructions

Installation, Care, and Service

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing (except as specified on pages 56–60 in this manual) to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

16) WARNING: This product contains a lamp to project

the picture, and requires special safety precautions:

• See pages 56–60 for instructions on lamp unit

replacement.

• DO NOT attempt to service this product except as

specified on pages 56–60. The only user-serviceable item in this product is the lamp unit.

Wide plug

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

17) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

18) DANGER: RISK OF SERIOUS PERSONAL

INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on

an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

19) Never place or store the TV in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C).

20) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit.

21) Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled with liquid, or candles on top of the TV.

22) Always place the back of the television at least one (1) inch away from any vertical surface (such as a wall) to allow proper ventilation.

23) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar surface;

• too close to drapes, curtains, or walls; or

• in a confined space such as a bookcase, built-in cabinet,

or any other place with poor ventilation.

The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV.

24) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

25) Never overload wall outlets and extension cords.

26) Always operate this equipment from a 120 VAC, 60 Hz power source only.

62HM14(E)02-05 1/24/05, 9:42 PM3

(continued on next page)

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Power service grounding electrode system (NEC Art 250 Part H)

Ground clamps

Antenna lead-in wire

Electric service equipment

Installation

(cont. from previous page)

Care

(cont. from previous column)

27) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

28) DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH!

• Use extreme care to make sure you are never in

a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

33) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

) During normal use, the TV may make occasional snapping

or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

35)

Special care for DLP

•

Lamp—The lamp in this product has a limited service life.

(digital light processing) units:

The length of service life varies depending on product use or user settings. If you use the lamp beyond its service life:

- you may notice a reduction in the colors and/or

brightness of the picture, at which time you should replace the lamp unit; and

- the strength of the quartz glass in the lamp will be

reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

See “Appendix” on pages 56–59.

Note:

• The lamp unit is designed so broken lamp glass remains

securely inside the lamp unit.

• The lamp unit contains mercury. Disposal of

mercury may be regulated due to environmental

information, please contact your local authorities or the Electronics Industries Alliance (www.eiae.org).

• Dispose of the used lamp unit by the approved method for your area.

considerations. For disposal or recycling

29) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen. Turn the TV off to check for reflections on the screen, and then remove the source of reflections while viewing the TV.

30) Always unplug the TV before cleaning. Never use liquid or aerosol cleaners. Clean only with a dry cloth. Do not spray volatile compounds such as insecticide on the cabinet. This may cause a discoloration or damage of the cabinet.

31) WARNING: RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV cabinet slots.

32) If the air temperature rises suddenly (for example, when the TV is first delivered), condensation may form on the lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the TV for 6 to 7 hours to allow the condensation to evaporate.

Service

) WARNING: RISK OF ELECTRIC SHOCK!

Never attempt to service the TV yourself,

except as specified on pages 56–60. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Center.

37) If you have the TV serviced:

• Ask the service technician to use only replacement parts

specified by the manufacturer.

• Upon completion of service, ask the service technician to

perform routine safety checks to determine that the TV is in safe operating condition.

38) When the TV reaches the end of its useful life, ask a qualified service technician to properly dispose of the TV.

Note: The lamp unit contains mercury. Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance (www.eiae.org). Dispose of the used lamp unit by the approved method for your area.

62HM14(E)02-05 1/24/05, 9:42 PM4

Important notes about your DLPTM projection TV

1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black, or the lamp may fail, at which time you must replace the lamp unit. See “Lamp unit replacement” on pages 56-59.

2) Each time you turn on the TV, it may take up to several seconds to go from no picture to full picture brightness.

3) The display on this TV is manufactured using a chip that may contain up to 1.3 million microscopic mirrors. Each of these micromirrors measures less than one-fifth the width of a human hair and represents a single pixel on the television display. These micromirrors are mounted on tiny hinges that enable them to tilt either toward the light source (ON) or away from it (OFF). Occasionally, one of these mirrors may become inoperative, creating a light or dark pixel on the projection surface. This is a structural property of DLP™ projection TV technology, and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance (see item 29 on page 4).

4) Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a “rainbow effect” on the screen, which can, in rare instances, result in eye fatigue. This is a rare occurrence related to technology of this type, and is not a sign of TV malfunction.

5) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture quality may be affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer from eye fatigue. See item 29 on page 4.

6) This TV contains several cooling fans to moderate

the internal temperature. You may be able to hear

the fans for several minutes after the TV is turned off. This is a function of the Quick Restart standby mode and is not a sign of TV malfunction. You can set the Quick Restart feature to stop the fans as soon as the TV is turned off. See “Selecting the Quick Restart” on page 25.

7) The green and red LED lights on the control touchpad (on the lower right corner of the TV screen) indicate your TV’s current status. If either light flashes, see “LED indications” on page 60 for details.

8) Review all safety and operating information in this owner’s manual before you use your TV.

The DLP logo and DLP medallion are trademarks of Texas Instruments.

62HM14(E)02-05 1/24/05, 9:42 PM5

Important Safety Information ............................. 2-5

Introduction................................................................ 7

Welcome to Toshiba ......................................................... 7

Exploring your new TV ................................................... 7

Connecting your TV .................................................. 8

Connecting an antenna or cable TV................................. 8

Connecting a VCR .......................................................... 9

Connecting a cable converter box .................................... 9

Connecting a cable converter box and VCR................... 10

Connecting a DVD player or satellite receiver and

a VCR............................................................................ 11

Connecting a DVD player with ColorStream

(component video) and a VCR ...................................... 12

Connecting a DTV receiver/set-top box with ColorStream

(component video) and a VCR ................ 13

Connecting two VCRs ................................................... 14

Connecting a camcorder ................................................ 14

Connecting an HDMI™ or a DVI device to the

HDMI input ................................................................. 15

Connecting an audio system .......................................... 16

Using the remote control ...................................... 17

Preparing the remote control for use .............................. 17

Installing the remote control batteries ............................ 17

Remote control effective range ....................................... 17

Programming the remote control to operate a cable converter box, satellite receiver, VCR, DVD player,

or HTIB (home theater in a box) ................................... 18

Remote control codes .................................................... 18

Remote control codes (cont.) ......................................... 19

Using the remote control to operate a cable converter box, satellite receiver, VCR, DVD player, or HTIB

(home theater in a box) .................................................. 20

Learning about the remote control ................................. 21

Setting up your TV .................................................. 22

Learning about the menu system ................................... 22

Changing the on-screen display language ....................... 23

Selecting the antenna input ............................................ 23

Adding channels to the TV’s memory ............................ 24

Programming channels automatically...................... 24

Adding and erasing channels manually.................... 25

Changing channels ........................................................ 25

Selecting the Quick Restart ............................................ 25

Using the TV’s features.......................................... 26

Adjusting the channel settings ........................................ 26

Switching between two channels using Channel

Return .................................................................... 26

Switching between two channels using

SurfLock™............................................................. 26

Programming your favorite channels ....................... 26

Labeling channels ................................................... 28

Viewing the wide-screen picture formats

(480i, 480p and 1080i signals only) ............................ 29

Selecting the picture size ......................................... 29

Scrolling the Theater Wide picture

(Theater Wide 2 and 3 only) .................................. 31

Using the AUTO ASPECT feature ......................... 32

Using the POP double-window feature .......................... 33

Switching the main and POP pictures..................... 34

Switching the speaker audio (main or POP)............ 34

Double-Window aspect ratio .................................. 35

Using the programmed channel search function............. 35

Using the favorite channel search function .............. 36

About the auto favorite feature................................ 36

Using the LOCKS menu ............................................... 37

Entering the PIN code ............................................ 37

If you cannot remember your PIN code .................. 37

Using the V-CHIP menu ............................................... 37

ENABLE BLOCKING .......................................... 38

TV RATING (Independent rating system for

broadcasters) ........................................................... 38

MPAA RATING (Independent rating system for

movies) ................................................................... 39

BLOCKING OPTION .......................................... 39

Unlocking programs temporarily ............................ 40

Locking channels ........................................................... 40

Locking the video inputs ................................................ 42

Changing the PIN code ................................................. 42

Adjusting the picture ..................................................... 43

Selecting the picture mode ...................................... 43

Adjusting the picture quality ................................... 43

Saving your new preferences ................................... 44

Selecting the color temperature ............................... 44

Using the CableClear™ DNR feature .................... 45

Resetting picture adjustments ................................. 45

Selecting the lamp mode ......................................... 46

Selecting the cinema mode...................................... 46

Selecting the video input source ..................................... 47

Labeling the video input sources .................................... 47

Using the closed caption feature..................................... 48

Setting the ON timer ..................................................... 49

Setting the sleep timer.................................................... 49

Setting the clock ............................................................ 50

Adjusting the sound ....................................................... 51

Muting the sound ................................................... 51

Selecting stereo/SAP broadcasts .............................. 51

Using the WOW™ surround sound feature ........... 52

Adjusting the sound quality .................................... 52

Resetting your audio adjustments ........................... 53

Using the StableSound

feature .............................. 53

Turning off the built-in speakers ............................. 54

Selecting the Audio OUT sound ............................. 54

Selecting the background of the menu display ............... 55

Displaying on-screen information .................................. 55

Understanding the auto power off feature ...................... 55

Understanding the last mode memory feature ................ 55

Appendix ................................................................... 56

Lamp unit replacement .................................................. 56

When to replace the lamp unit................................ 56

How to replace the lamp unit ................................. 57

Lamp unit disposal ................................................. 59

LED indications ............................................................ 59

Specifications ................................................................. 60

Troubleshooting ............................................................. 61

Limited United States Warranty ..................................... 62

Index .......................................................................... 63

62HM14(E)06 1/24/05, 9:29 PM6

Introduction

Welcome to Toshiba

Congratulations! You have purchased one of the finest DLP projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible.

This manual applies to model 62HM14. The model and serial numbers are on the back of your TV. Write these numbers in the space provided on the front cover of this manual for your records.

Instructions in this manual are based on using the remote control. You can also use the controls on the TV if they have the same name as those on the remote control.

Please read all the safety and operating instructions carefully, and keep the manual for future reference.

Exploring your new TV

You can operate your TV using the control touchpad on the TV front or the remote control. The back panel and side panel (behind the door) provide terminals for connecting other equipment to your TV. See “Connecting your TV” on page 8.

™

See “Important notes about your DLPTM projection TV” on page 5.

Introduction

your TV

Connecting

Using the

Remote Control

Front

Remote control sensor

(Behind the screen)

Side

Push to open.

Back

Remote control

Control touchpad on TV front (Gently touch the printed keys.)

POWER

TV/VIDEO

EXIT

zyx •

TV / VIDEO

123

456

FAVORITE

100

MENUVOLUMECHANNELEXITTV/VIDEO POWER

Volume x •

Channel zy

MENUVOLUMECHANNELEXITTV/VIDEO POWER

Green and Red LED indicators*

* Green ON = Touchpad key being pressed;

Red ON = Power ON. See page 60 for additional LED indications.

VIDEO 3

/audio inputs

Vid

ANT-2 IN

ANT OUTAUDIO

ANT-1 IN

ENTER

TV CBL/SAT VCR DVD

POP DIRECT CH MUTE SLEEP

TV/VCR PAUSE

CH SCAN

REC

RECALL

INFO

+10

FAV

DVDMENU

FAV

VOLCH

STOP

FREEZE SOURCE

SKIP / SEARCH

FFREW

SWAP POP CH

POWER

CHRTN

ENT

PIC SIZE

EXIT

PLAY

SPLIT

LIGHT

your TV

Setting up

Features

Using the TV’s

Appendix

CT-90159

62HM14(E)07 1/24/05, 1:36 PM7

VIDEO 1/2

ColorStream

HD-1/HD-2

Video/Audio OUT

Variable Audio OUT

Index

HDMI IN

Connecting your TV

Note: Cables are not supplied with your TV.

Introduction

your TV

Connecting

●

Coaxial cable is the cable that comes in from your antenna, cable TV service, or cable converter box. Coaxial cable uses “F” connectors.

Standard A/V (audio/video) cables usually come in sets of three, and are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. On your TV’s back panel, the standard A/V inputs are color-coded in the same manner as the cables.

S-Video cable is for use with video equipment that has S-Video output. Component video cables come in sets of three, and are for use with

video equipment that has component video output. (ColorStream

Toshiba’s brand of component video.) HDMI is for use with video equipment that has HDMI output (type

A connector) (see page 15).

Coaxial (antenna) cable

Standard A/V cables (red/white/yellow)

S-video cable

Component video cables

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Connecting an antenna or cable TV

This connection allows you to watch TV programs or basic cable channels.

From Antenna or Cable

HDMI cable

CAUTION: RISK OF EQUIPMENT DAMAGE !

Never plug in any power cords until you have finished connecting all equipment.

Appendix

Index

62HM14(E)08-16 1/24/05, 1:42 PM8

Connecting a VCR

This connection allows you to watch local channels and video programs, play or record on the VCR while watching TV, and record from one channel while watching another channel.

You will need:

• two coaxial cables

• one set of standard A/V cables

From Cable Box or Antenna

Stereo VCR

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a VCR with S-video, use an Svideo cable (in the S-video jacks) instead of the standard video cable.

Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Introduction

your TV

Connecting

Using the

Remote Control

Connecting a cable converter box

This connection allows you to watch basic and premium cable channels To watch basic cable and use the TV’s features, select ANT-1. To view

premium channels, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• three coaxial cables

From Cable

INOUT

Note:

When you use a converter box with your TV, the remote control will not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

your TV

Setting up

Features

Using the TV’s

Appendix

62HM14(E)08-16 1/24/05, 1:42 PM9

Cable converter box

Index

Connecting a cable converter box and VCR

This connection allows you to watch and record basic and premium cable channels, watch videotapes, and record one channel while

Introduction

your TV

Connecting

Using the

Remote Control

watching another channel. To watch basic cable and use the TV’s features, select ANT-1.

To view premium channels or record with the VCR, select ANT-2, tune the TV and VCR to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• four coaxial cables

• one set of standard A/V cables

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a VCR with S-video, use an S-video cable (in the S-video jacks) instead of a standard video cable. Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

When you use a converter box with your TV, the remote control will not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

From Cable

your TV

Setting up

Features

Using the TV’s

Appendix

IN from ANT OUT to TV

CH 3 CH 4

Stereo VCR

VIDEO

OUT

AUDIO

INOUT

Cable converter box

Index

62HM14(E)08-16 1/24/05, 1:42 PM10

Connecting a DVD player or satellite receiver and a VCR

This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel.

You will need:

• two (or three, if satellite receiver is used) coaxial cables

• one set of standard A/V cables

• one S-video cable

• one pair of standard audio cables

Stereo VCR

OUT

AUDIO

From

Antenna

IN from ANT OUT to TV CH 3

CH 4

VIDEO

Note:

For the highest possible picture quality from a DVD player or satellite receiver without component video or HDMI, use an S-video cable. (If your DVD player has component video, see page 12. If your DVD player or satellite receiver has HDMI or DVI, see page

15.)

Do not connect both an S-video cable and a standard video cable between the TV and DVD player/satellite receiver at the same time or the picture performance will be unacceptable.

Do not connect the DVD player/satellite receiver and VCR to the same set of Video inputs on the TV. (See the illustration, which shows the DVD player/satellite receiver connected to VIDEO 1 on the TV, and the VCR connected to VIDEO 2 on the TV.)

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

From

Satellite

Dish

IN from ANT

S-VIDEO

VIDEO

OUTOUT

VIDEO

OUTOUT

DVD Player

AUDIO

OUT

Satellite Receiver

AUDIO

OUT

Features

Using the TV’s

Appendix

Index

62HM14(E)08-16 1/24/05, 1:42 PM11

Connecting a DVD player with ColorStream (component video) and a VCR

This connection allows you to watch DVD, VCR, and TV programs,

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

and record TV programs. Your TV has ColorStream

your TV to a DVD player with component video (such as a Toshiba DVD player with ColorStream and realism.

– To record one TV program while watching another TV program,

– To record a TV program while watching a DVD, tune the VCR to

You will need:

(component video) inputs. Connecting

) can greatly enhance picture quality

tune the VCR to the channel to record, and tune the TV to the channel to watch.

the channel to record, and select ColorStream HD1 on the TV (see

“Selecting the antenna input” on page 23).

• two coaxial cables

• one set of standard A/V cables

• one pair of standard audio cables

• one set of component video cables

From Antenna

Stereo VCR

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DVD player.

You can connect the component video cables to either set of ColorStream inputs on the TV (HD1 or HD2).

For HDMI or DVI connection, see page 15.

The ColorStream HD1/HD2 and HDMI inputs can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems; however, a 1080i signal will provide the best picture performance.

If your DVD player is not compatible with component video, HDMI, or DVI, use the S-video connections (plus the standard audio connections) instead (see page 11).

Features

Using the TV’s

Appendix

Index

S-VIDEO

COMPONENT VIDEO

DVD player with component video

RPB

VIDEO

OUT

AUDIO

OUT

62HM14(E)08-16 1/24/05, 1:42 PM12

Connecting a DTV receiver/set-top box with

ColorStream

This connection allows you to watch DTV (digital TV), VCR, and TV programs, and record DTV and TV programs.

Your TV has ColorStream (component video) inputs. Connecting your TV to a DTV receiver with component video can greatly enhance picture quality and realism.

– To record and watch a DTV program, select LINE IN on the

VCR, and select ColorStream HD2 (or VIDEO 1 for a nonColorStream connection) on the TV (see “Selecting the antenna input” on page 23).

– To record a TV program while watching a DTV program, tune the

VCR to the channel to record, and select ColorStream HD2 on the TV.

– To record and watch the same TV program, tune the VCR to the

channel to record, and select VIDEO 1 on the TV.

– To record one TV program while watching another TV program,

tune the VCR to the channel to record, and tune the TV to the channel to watch.

You will need:

• three coaxial cables

• two sets of standard A/V cables

• one pair of standard audio cables

• one set of component video cables

From Antenna

(component video) and a VCR

Stereo VCR

Note:

For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DTV receiver/set-top box.

You can connect component video cables to either set of ColorStream inputs on the TV (HD1 or HD2).

For HDMI or DVI connection, see page 15.

The ColorStream HD1/HD2 and HDMI inputs can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems; however, a 1080i signal will provide the best picture performance.

If your DTV receiver or set-top box is not compatible with component video or HDMI, use the S-video connections (plus the standard audio connections) instead (see page 11).

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

From DTV Antenna

IN from ANT OUT to TV CH 3

CH 4

Satelite IN

DTV Receiver with component video

S-VIDEO

VIDEO

COMPONENT VIDEO

OUT

AUDIO

RPB

VIDEO

OUT

AUDIO

OUT

Features

Using the TV’s

Appendix

Index

62HM14(E)08-16 1/24/05, 1:42 PM13

Connecting two VCRs

This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. You also can record from

Introduction

your TV

Connecting

one TV channel while watching another TV channel. You will need:

• two coaxial cables

• two sets of standard A/V cables

From Antenna

VCR1

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

If you have VCRs with S-video, use S-video cables instead of standard video cables for better picture performance. Do not connect both a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

Do not connect the same VCR to the output and input jacks on the TV at the same time. To dub or edit, VCR 2 must select Line IN, and the TV must select VIDEO 1 (see “Selecting the antenna input” on page 23).

* The VIDEO OUT jack does not output the

POP picture.

** The AUDIO OUT jacks can output the

sound of either the Main or POP picture (see “Selecting the Audio OUT sound” on page 54).

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

VCR2

CH 3 CH 4

VIDEO AUDIO

OUT

Connecting a camcorder

This connection allows you to watch video materials recorded on a camcorder.

You will need:

• one set of standard A/V cables

Note:

If you have a camcorder with S-video, use an S-video cable instead of a standard video cable for better picture performance. Do not connect both a standard video cable and an S-video cable at the same time, or the picture performance will be unacceptable.

Appendix

Index

62HM14(E)08-16 1/24/05, 1:42 PM14

VIDEO

AUDIO

OUT

Camcorder

Video-3 (side panel)

Connecting an HDMI™ or a DVI device to the HDMI input

The HDMI and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device.

This input is designed to accept HDCP material in digital form from EIA/CEA-861/861B– compliant top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with 1080i high-definition video signals, but will also accept and display 480i, 480p, and 720p signals.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector)

[1]

input on your TV receives digital audio

[2]

[3]

program

[4]

consumer electronic devices (such as a set-

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

For proper operation, it is recommended that you use a short HDMI cable. You should not encounter difficulty if you use an HDMI cable that is shorter than

16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (Video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with this connection, the HDMI terminal on the TV will not receive the HDMI digital audio signal and you will hear analog audio only.

[1]

HDMI = High-Definition Multimedia Interface.

[2]

DVI = Digital Video Interface.

[3]

HDCP = High-bandwidth Digital Content Protection.

[4]

EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals.

evolving technology, it is possible that some source devices with HDMI or DVI output may not work with the HDMI input on this TV.

To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

• When turning on your electronic components,

turn on the TV first, and then the HDMI or DVI device.

• When turning off your electronic components,

turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

• one HDMI

–to–

DVI adapter cable

(HDMI type A connector)

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

• one pair of standard analog audio cables

An HDMI-to-DVI adapter cable transfers only video. Separate analog audio cables are required (see illustration below).

Because this is an

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

HDMI device

VIDEO AUDIO

OUT

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

HDMI OUT

DVI device

VIDEO AUDIO

DVI

OUT

Features

Using the TV’s

Appendix

Index

62HM14(E)08-16 1/24/05, 1:42 PM15

Connecting an audio system

This connection allows you to use an audio amplifier and external speakers, and adjust the audio level by using the TV’s remote control.

Introduction

your TV

Connecting

To control the audio, turn on the TV and the stereo amplifier, and turn off the built-in speakers (see “Turning off the built-in speakers” on page 54).

You will need:

Note:

To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set above 0 (zero).

For example, if the volume of the TV is set to 0, you will not be able to hear any sound, even the volume of the amplifier is at its highest level.

• one pair of standard audio cables

Amplifier

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

LINE IN LR

Appendix

Index

62HM14(E)08-16 1/24/05, 1:42 PM16

Using the remote control

Preparing the remote control for use

Your TV remote control can operate your TV and many cable converter boxes, satellite receivers, VCRs, DVD players, and HTIBs (home theater in a box), even if they are different brands.

If you have a Toshiba device:

Your TV remote control is preprogrammed to operate most Toshiba devices. See page 20.

If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate:

You can program the TV remote control so it will operate the other device. See pages 18–20.

Installing the remote control batteries

1. Remove the battery cover from the back of the remote control.

Squeeze tab and lift cover.

2. Install two “AA” size batteries, making sure to match the + and – signs on the batteries to the signs on the battery compartment.

3. Reinsert the battery cover in the remote control until the tab snaps.

Remote control effective range

For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV.

Caution:

• Never throw batteries into a fire.

Note:

• If your Toshiba TV remote control does not operate all the features of your other device, use the original remote control for that device.

• Dispose of batteries in a designated disposal area.

• Attention should be drawn to the environmental aspects of battery disposal.

• Do not mix battery types or combine used batteries with new ones.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace both batteries with new ones.

• If the batteries are dead or if you will not use the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

62HM14(E)17-21 1/24/05, 1:44 PM17

Appendix

Index

Programming the remote control to operate a cable converter box, satellite receiver, VCR, DVD player, or HTIB (home theater in a box)

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see page 20.

Remote control codes

In some cases you may not be able to operate your device with the TV

Features

Using the TV’s

remote control. Your other device may use a code that is not recognized by the TV remote control. If this happens, use the device’s remote control.

1. In the remote control code table (below and on the next page), find the code for your device. If more than one code is listed, try each one separately until you find one that works.

2. Set the Device Switch to the type of device you are programming the remote control to operate — CBL/SAT (for a cable converter box or satellite receiver), VCR (for a VCR or TV/VCR combo), or DVD (for a DVD player or HTIB [home theater in a box]).

3. While holding down RECALL, press the Channel Number buttons to enter the 3-digit code for your device.

4. To test the code, turn on the device, point the remote control at it, and press POWER. See note at right.

• If the correct code was entered, the device will turn off.

• If the device does not respond, repeat steps 1–4 using another code.

• If the device does not respond to another code, you will need to use the remote control that came with the device.

Remember to set the Device Switch back to TV to control the TV.

6. For future reference, write down the code(s) you used:

DEVICE CODE DEVICE CODE

POWER

RECALL

TV / VIDEO

INFO

123

456

RECALL POWER

Channel

+10

100

FAVORITE

ENTER

TV CBL/SAT VCR DVD

POP DIRECT CH MUTE SLEEP

TV/VCR PAUSE

Note:

CH SCAN

• In addition to POWER, confirm that all

REC

FAV

DVDMENU

FAV

VOLCH

STOP

FREEZE SOURCE

SKIP / SEARCH

FFREW

SWAP POP CH

CHRTN

ENT

PIC SIZE

EXIT

PLAY

SPLIT

LIGHT

Number

Device Switch

necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

• Every time you change the batteries, you will need to reprogram the remote control.

• Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

Cable converter box

ABC: 061, 062, 063,

082, 084, 087, 091, 092, 096, 098

Appendix

Archer: 065, 092, 097,

099 Cableview: 064, 094 Century: 092 Citizen: 090, 092, 097 Contec: 083, 085, 086,

088, 093, 098 Diamond: 093 Eagle: 091

Index

GE: 061, 062 Gemini: 069, 070, 094 General Instruments:

062, 089, 096

62HM14(E)17-21 1/24/05, 1:44 PM18

Hamlin: 093 Hitachi: 062, 095, 096 Jasco: 097 Jerrold: 062, 069, 071,

082, 086, 089, 091,

096 Magnavox: 072, 096 Memorex: 091, 092, 104 Multi Canal: 090 Novavision: 101 Panasonic: 081, 083, 085 Philco: 087 Philips: 066, 067, 068,

070, 072, 073, 074,

075, 091, 092 Pioneer: 076, 077 Proscan: 061, 062 Radio Shack: 092, 097,

099

RCA: 064, 081 Realistic: 065 Recoton: 102 Samsung: 077, 090 Scientific Atlanta: 063,

078, 079, 080, 088,

098, 101, 105 Sears: 095 Signature: 062 Signature 2000: 096 Sprucer: 081, 085 Starcom: 069, 082, 087,

096, 103, 104 Stargate: 069, 090 Sylvania: 095, 100 TeleView: 090 Texscan: 100 Tocom: 071, 084, 085

U. S. Electronics: 087,

096, 098 United Cable: 082 Universal: 065, 092, 097,

099, 102, 103 Wards: 096

Satellite receiver

Alphastar: 038, 059 Chaparral: 034 DISH Network: 057 Drake: 020, 040, 044,

046, 050, 053 Echostar: 018, 041, 051 Express Vu: 057 Fujitsu: 027 GE: 008, 009, 013

General Instruments:

010, 011, 012, 022,

023, 031, 049 Hitachi: 033 Hughes: 033 Hughes Network

Systems: 019 Intersat: 048 Janeil: 027 JVC: 017, 057 Kenwood: 029 Magnavox: 060 Optimus: 058 Pansat: 036, 052 Primestar: 015, 042 Proscan: 008, 009, 013 Radio Shack: 022, 023,

030

Remote control codes (cont.)

Satellite receiver (cont.)

RCA: 008, 009, 013, 016 Realistic: 030 Samsung: 059 Sony: 014, 055 Star Choice: 057 Star Trak: 025, 026, 037,

054 STS: 024 Toshiba: 000, 001, 002,

003, 004, 005, 006,

007, 020, 031, 056 Uniden: 021, 028, 030,

032, 035, 039, 043,

045, 047, 058 Zenith: 027

TV/VCR Combo

Action: 078 GE: 059, 062 Goldstar: 065 Panasonic: 065 Precision: 078 Quasar: 065 Realistic: 079 Sony: 074 Toshiba: 057 Zenith: 065

DVD/VCR Combo

Go Video:

DVD=087, VCR=081 JVC:

DVD=088, VCR=082 RCA:

DVD=089, VCR=083 Samsung:

DVD=090, VCR=084 Sanyo:

DVD=091, VCR=085 Zenith:

DVD=092, VCR=086

DVD player

Aiwa: 006, 015 Apex: 016, 017 BOSE: 097 Broksonic: 018 Clarion: 019 Classic: 020 Daewoo: 021 Denon: 022, 023, 024,

025 Emerson: 026, 027 Fisher: 028 Funai: 027 GE: 001, 029, 030 Go Video: 087 GPX: 031

Hitachi: 005, 032, 033,

034, 035

JVC: 003, 007, 036,

042, 088 Kenwood: 037 Konka: 008, 009 Magnavox: 004, 038 Memorex: 039 Mintek: 040 NAD: 026 Nakamichi: 041 Norcent: 043 Onkyo: 044 Oritron: 058 Panasonic: 010, 045,

046, 047, 048, 049,

050 Philips: 004, 051 Pioneer: 052, 053, 054,

055 Proscan: 001, 056 Qwestar: 057, 058 RCA: 001, 002, 059, 089 Sampo: 060 Samsung: 061, 062, 086,

090 Sansui: 073 Sanyo: 063, 091 Sharp: 064, 067 Sherwood: 074 Sony: 011, 012, 065,

066, 068, 069, 070 Sylvania: 027 Teac: 071 Technics: 072 Techwood: 075 Toshiba: 000, 013, 076,

077, 078 Yamaha: 079, 080, 081 Zenith: 014, 082, 092

Portable DVD player

Aiwa: 093 Audiovox: 094, 095 Panasonic: 024, 096, 099 RCA: 098

VCR

Admiral: 049 Aiko: 019 Aiwa: 018 Akai: 003, 004, 037,

038, 039, 058, 069 Audiovox: 010 Bell & Howell: 007, 068 Broksonic: 008, 017 Calix: 010 Carver: 026 CCE: 019 Citizen: 009, 010, 011,

012, 013, 014, 015,

019, 057, 073

Colortyme: 005 Craig: 009, 010, 016,

061, 065, 079

Curtis Mathes: 001, 005,

009, 012, 014, 040, 048, 053, 056, 057

Daewoo: 011, 013, 015,

017, 018, 019, 057,

078 Daytron: 078 Denon: 063 Dimensia: 001, 048 Electrohome: 010, 020,

065 Emerson: 003, 008, 010,

011, 017, 018, 020,

028, 039, 054, 057,

062, 065, 068, 072 Fisher: 007, 016, 021,

022, 023, 057, 064,

068, 070, 071, 079 Fuji: 004, 041 Funai: 018, 073 Garrard: 018 GE: 001, 002, 009, 040,

042, 048, 056 Go Video: 056, 059,

061, 081 Goldstar: 005, 010, 014,

054, 056, 065, 067 Gradiente: 018, 065 Harman Kardon: 005 Hitachi: 024, 025, 035,

037, 042, 063, 070,

080 JBL: 076 JC Penney: 005, 006,

007, 008, 009, 010,

023, 024, 025, 026,

035, 056, 061, 063,

065 Jensen: 024, 025, 037,

050 JVC: 005, 006, 007,

014, 037, 043, 050,

062, 063, 068, 082 Kenwood: 005, 006,

007, 012, 014, 037,

043, 050, 053, 068,

071 Kodak: 010 LG: 010 Lloyds: 053, 073, 079 Logik: 061 LXI: 010 Magnasonic: 061, 065,

078 Magnavox: 026, 027,

034, 044, 057, 061,

072 Marantz: 005, 006, 007,

012, 014, 026, 053,

067

Memorex: 007, 009,

010, 016, 018, 034, 049, 063, 065, 066,

068, 075, 079 MGA: 020, 028, 039 MGN: 056 Minolta: 024, 025, 035,

063 Mitsubishi: 020, 024,

025, 028, 039, 043,

065 Montgomery Ward: 049 Motorola: 049 MTC: 009, 046, 061 Multitech: 009, 012, 018 NEC: 005, 006, 007,

012, 014, 037, 043,

053, 054, 067, 070 Nikko: 010 Noblex: 009 Optimus: 010, 049, 065 Optonica: 031 Orion: 054, 057, 062,

065, 068, 072 Panasonic: 036, 045,

046, 057, 061, 072,

079 Pentax: 012, 024, 025,

035, 042, 053, 063 Pentex Research: 014 Philco: 026, 027, 063 Philips: 026, 031, 044,

057 Pioneer: 006, 024, 043,

055 Portland: 012, 013, 015 Proscan: 001, 002, 048 Proton: 061 Quasar: 045 Radio Shack: 010, 031,

065 Radio Shack/Realistic:

007, 009, 010, 016,

018, 020, 021, 022,

031, 049 Radix: 010 RCA: 001, 002, 003,

009, 024, 025, 029,

035, 040, 042, 045,

048, 055, 056, 063,

071, 083 Realistic: 007, 009, 010,

011, 016, 018, 020,

021, 022, 031, 049,

051, 056, 060, 065,

075, 079 Ricoh: 047 Runco: 034 Samsung: 009, 011, 038,

056, 073, 084 Sansui: 006, 037, 043,

061

Sanyo: 007, 009, 016,

054, 064, 068, 071, 075, 079, 085

Scott: 008, 011, 017,

028, 030, 057, 065, 072

Sears: 007, 010, 016,

021, 022, 023, 024, 025, 035, 053, 057, 063, 064, 065, 068, 071, 075, 079

Sharp: 013, 020, 031,

049, 051, 060, 066

Shintom: 004, 025, 032,

061 Signature: 049 Signature 2000: 075 Singer: 047, 061 Sony: 004, 032, 033,

041, 052, 058, 070,

074, 076, 077, 080 STS: 035 Sylvania: 018, 026, 027,

028, 044, 072 Symphonic: 018, 050,

051, 053, 073, 079 Tandy: 007 Tashiko: 010 Tatung: 037 Teac: 018, 029, 037 Technics: 036 Teknika: 010, 018, 065 Toshiba: 000, 011, 021,

023, 024, 028, 030,

039, 057, 074, 078,

079 Totevision: 009, 010,

065 Unitec: 073 Unitech: 009 Vector Research: 005,

006, 011, 012, 053 Video Concepts: 005,

006, 011, 012, 039,

053 Wards: 009, 010, 011,

016, 018, 020, 024,

025, 031, 035, 049,

051, 056, 057, 060,

065, 066, 079 White Westinghouse:

073 XR-1000: 018 Yamaha: 005, 006, 007,

014, 037, 053 Zenith: 004, 032, 034,

041, 047, 069, 086

HTIB

Lasonic: 083 Panasonic: 084 Venturer: 085

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

62HM14(E)17-21 1/24/05, 1:44 PM19

Using the remote control to operate a cable converter box, satellite receiver, VCR, DVD player, or HTIB (home theater in a box)

Introduction

your TV

Connecting

If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you must first program the remote control to recognize the device (if you have not already done so). See pages 18 and 19.

To use your TV remote control to operate a:

• Cable converter box or satellite receiver, set the Device Switch to

CBL/SAT.

• VCR, set the Device Switch to VCR.

• DVD player or HTIB, set the Device Switch to DVD.

Point the remote control

directly at the device.

Note:

Even after the TV remote control is programmed, it may not operate certain features on your other device. If this happens and you wish to use those features, you will need to use the device’s original remote control.

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

TV / VIDEO

+10 (DVD only)

Press to directly access

DVD chapters higher than 10.

TOP MENU (DVD only)

Accesses a DVD’s top menu.

ENTER

Required by some VCRs and cable

converter boxes to change the channel.

Device Switch

Set to “TV” to control the TV; “CBL/SAT” to

control a cable converter box or satellite

receiver; “VCR” to control a VCR; “DVD”

TV CBL/SAT VCR DVD

to control a DVD player or HTIB.

PAU SE

Press during play or record mode to

pause the picture; press again to restart.

TV/VCR PAUSE

TV/VCR (VCR only)

To view one program while recording

another, press to select TV mode.

CH SCAN

REW

Rewinds the tape or DVD. (Press during play mode

to view the picture moving rapidly backward.)

REC (VCR only)

Starts tape recording.

Fast-forwards the tape or DVD.

(Press during play mode to view the

picture moving rapidly forward.)

RECALL

POWER

INFO

123

456

100

FAVORITE

ENTER

REC

FAV

CHRTN

ENT

PIC

VOLCH

STOP

SKIP / SEARCH

+10

DVDMENU

POP DIRECT CH MUTE SLEEP

FREEZE SOURCE

FFREW

SWAP POP CH

CT-90159

EXIT

PLAY

SPLIT

LIGHT

POWER

Turns the selected device on and off.

INFO (CBL/SAT only)

Displays on-screen information.

Channel Numbers (0-9)

Press to directly access channels (as opposed to CH y z).

GUIDE (CBL/SAT only)

Displays channel guide.

y z x • (DVD only) Press to navigate DVD menus (may not work on some DVD players).

Press to reset the title and chapter

CLEAR (DVD only)

number.

CH y z y selects the next higher channel; z selects the next lower channel.

PLAY

Begins playback of a tape or DVD.

STOP

Stops the tape or DVD.

SKIP/SEARCH

(DVD only)

Skips forward to locate later DVD chapters.

SKIP/SEARCH (DVD only)

Skips back to beginning of current DVD chapter or locates previous chapters.

62HM14(E)17-21 1/24/05, 1:44 PM20

+ 44 hidden pages