Toshiba 32CV504, 32CV505, 37CV504, 37CV505, 42CV504 User Manual
...
CV50*
DIGITAL
Series
Contents
SETTING UP
Safety Precautions ..................................................4
Installation and important information ....................5
The remote control .................................................6
Inserting batteries and effective range of the
remote ..........................................................7
Connecting external equipment ..............................8
Connecting an HDMI™ or DVI device to the HDMI
input ...................................................................9
To connect an HDMI device ..............................9
To connect a DVI device ...................................9
REGZA-LINK connection .......................................10
Connecting a computer ........................................11
To connect a PC to the RGB/PC terminal ........11
To connect a PC to the HDMI terminal ............11
Controls and input connections .............................12
Switching on ..................................................12
Using the remote control ...............................12
Using the controls and connections ................12
TUNING THE TELEVISION
Tuning Digital television .......................................13
Tuning for the first time ..................................13
Digital auto tuning .......................................14
Analogue switch-off .....................................14
Digital programme sorting ............................15
Digital manual tuning ...................................15
Tuning Analogue mode ........................................16
Quick Setup ...................................................16
Manual tune ..................................................17
Programme skip ............................................18
Sorting programme positions .........................19
Using Auto tuning ..........................................19
CONTROLS AND FEATURES
General controls ...................................................20
Selecting programme positions ......................20
The Time Display – analogue only ................20
Stereo and Bilingual transmissions .................20
Sound controls .....................................................20
Volume controls and mute sound ...................20
Bass, Treble and Balance ...............................20
Bass boost .....................................................20
SRS WOW® sound effects ..............................21
Dual – analogue only ...................................21
Stable sound® ...............................................21
Headphone Mode ..........................................21
Widescreen viewing ..............................................22
Picture controls .....................................................24
Picture position – analogue only ...................24
Backlight .......................................................24
Picture preferences ........................................25
Black/White Level ..........................................25
Cinema mode ................................................25
Colour temperature .......................................25
Reset .............................................................25
3D Colour management ................................26
Base colour adjustment ..................................26
Active Backlight Control .................................26
Auto Contrast ................................................26
MPEG NR – Noise Reduction ..........................26
DNR – Digital Noise Reduction .......................27
Automatic format (Widescreen) ......................27
4:3 stretch .....................................................27
Blue screen ....................................................27
Side panel adjustment ...................................27
Picture still .....................................................27
Panel lock ............................................................27
The timers ............................................................28
Programme timer – digital only ....................28
Sleep timer ....................................................28
Digital on-screen information and
Programme Guide .............................................29
Information ...................................................29
Guide ...........................................................29
Digital settings – parental control ........................30
Setting the PIN ..............................................30
Mode ............................................................30
Digital settings – other features ...........................31
Selecting favourite programmes .....................31
Locking programmes .....................................31
Encrypted programmes ..................................31
Audio languages ...........................................32
Optical audio output .....................................32
Subtitles ........................................................32
Audio description ..........................................32
Reset TV ........................................................32
Common interface .........................................33
Digital settings – software upgrade ......................33
Version .........................................................33
Auto Upgrade ...............................................33
Searching for new software ...........................33
PC settings – picture position, clock phase,
sampling clock, reset .........................................34
Picture position ..............................................34
Clock phase ..................................................34
Sampling clock ..............................................34
Reset .............................................................34
Input selection and AV connections ......................35
Input selection ...............................................35
INPUT signal selection ...................................35
PC audio .......................................................36
HDMI1 audio ................................................36
Lip Sync Latency ............................................36
Using REGZA-LINK ...............................................37
Enable REGZA-LINK ......................................37
TV Auto Input Switch .....................................37
TV Auto Power ...............................................37
Auto Standby ................................................37
Speaker Preference .......................................37
REGZA-LINK input source selection ................37
REGZA-LINK playback device control .............38
REGZA-LINK one touch play ..........................38
REGZA-LINK system standby ..........................38
REGZA-LINK system audio control ..................38
REGZA-LINK PC link ......................................38
TEXT SERVICES
Text services .........................................................39
Selecting modes ............................................39
Text information ............................................39
Navigating pages using Auto. ........................39
Navigating pages using LIST ..........................39
Control buttons .............................................40
Digital interactive services ...................................40
PROBLEM SOLVING
Questions and Answers ......................................41
INFORMATION
Notes ...................................................................44
Information ..........................................................46
Specifications and accessories ..............................48
3
SETTING UP
Safety Precautions
This equipment has been designed and manufactured
to meet international safety standards but, like any
electrical equipment, care must be taken to obtain the
best results and for safety to be assured. Please read
the points below for your own safety. They are of a
general nature, intended to help with all electronic
consumer products and some points may not apply to
the goods you have just purchased.
Air Circulation
Leave more than 10cm clearance around the television
to allow adequate ventilation. This will prevent
overheating and possible damage to the television.
Dusty places should also be avoided.
Heat Damage
Damage may occur if the television is left in direct
sunlight or near a heater. Avoid places subject to
extremely high temperatures or humidity. Place in a
location where the temperature remains between 5°C
(41°F) min. and 35°C (94°F) max.
Mains Supply
The mains supply required for this equipment is 220240v AC 50/60Hz. Never connect to a DC supply or
any other power source. DO ensure that the television
is not standing on the mains lead.
DO NOT cut off the mains plug from this equipment,
this incorporates a special Radio Interference Filter, the
removal of which will impair its performance. In the
UK, the fuse fitted in this plug is approved by ASTA or
BS1362
BSI to
rated and approved type and the fuse cover must be
refitted.
IF IN DOUBT PLEASE CONSULT A COMPETENT
ELECTRICIAN.
DO
read the operating instructions before you attempt
to use the equipment.
DO
ensure that all electrical connections (including the
mains plug, extension leads and inter-connections
between pieces of equipment) are properly made and
in accordance with the manufacturers’ instructions.
Switch off and withdraw the mains plug before making
or changing connections.
DO
consult your dealer if you are ever in doubt about
the installation, operation or safety of your equipment.
DO
be careful with glass panels or doors on
equipment.
. It should only be replaced by a correctly
Do
DO NOT REMOVE ANY FIXED COVERS AS THIS WILL
EXPOSE DANGEROUS AND 'LIVE' PARTS.
THE MAINS PLUG IS USED AS A DISCONNECTING
DEVICE AND THEREFORE SHOULD BE READILY
OPERABLE.
Do not
DO NOT
equipment with items such as newspapers, tablecloths,
curtains, etc. Overheating will cause damage and
shorten the life of the equipment.
DO NOT
dripping or splashing or objects filled with liquids, such
as vases, to be placed on the equipment.
DO NOT
such as lighted candles or nightlights on, or close to
equipment. High temperatures can melt plastic and
lead to fires.
DO NOT
wood screws. To ensure complete safety, always fit the
manufacturers’ approved stand, bracket or legs with
the fixings provided according to the instructions.
DO NOT
unattended, unless it is specifically stated that it is
designed for unattended operation or has a standby
mode. Switch off by withdrawing the plug, make sure
your family know how to do this. Special arrangements
may need to be made for people with disabilities.
DO NOT
in any doubt about it working normally, or it is
damaged in any way – switch off, withdraw the mains
plug and consult your dealer.
WARNING
earphones or headphones can cause hearing loss.
ABOVE ALL – NEVER let anyone, especially
children, push or hit the screen, push anything
into holes, slots or any other openings in the
case.
NEVER guess or take chances with electrical
equipment of any kind – it is better to be safe
than sorry.
obstruct the ventilation openings of the
allow electrical equipment to be exposed to
place hot objects or naked flame sources,
use makeshift stands and NEVER fix legs with
leave equipment switched on when it is
continue to operate the equipment if you are
– excessive sound pressure from
4
SETTING UP
Installation and important information
Where to install
Locate the television away from direct sunlight and
strong lights, soft, indirect lighting is recommended for
comfortable viewing. Use curtains or blinds to prevent
direct sunlight falling on the screen.
Place on a sturdy platform, the mounting surface should
be flat and steady. It should be secured to the wall with
a sturdy tie using the clip on the back of the stand, or
secured to the platform using the fixing strap located
Clip
underneath the table top stand, this will prevent it from
falling over.
The LCD display panels are manufactured using an
extremely high level of precision technology, however
sometimes some parts of the screen may be missing
Side View Top View
picture elements or have luminous spots. This is not a
sign of a malfunction.
Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will break
or damage the screen, and that small items cannot be inserted into slots or openings in the case.
Please take note
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) fire;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s
manual ;
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not limited
to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal operation or
misuse of the product.
NOTE:
A Toshiba wall bracket or stand, where available, must be used. If a non Toshiba wall bracket or stand is used the product’s
BEAB approval will become void and the equipment is then used at the consumers own risk.
Sturdy tie
(as short as possible)
Clip
Clip
• The digital reception function of this television is only effective in the countries listed in the “COUNTRY SET UP” section of the
“DIGITAL MENU”. Depending on country/area, some of this television's functions may not be available. Reception of future
additional or modified services can not be guaranteed with this television.
• If stationary images generated by 4:3 broadcasts, text services, channel identification logos, computer displays, video games, on
screen menus, etc. are left on the television screen for any length of time they could become conspicuous, it is always advisable
to reduce both the brightness and contrast settings.
• Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at the 4:3 outlines, this
is not a defect of the LCD TV and is not covered under the manufacturers warranty. Regular use of other size modes (eg:
Superlive) and varying the “side panel” brightness (if available on the model) will prevent permanent retention.
5
SETTING UP
The remote control
Simple at-a-glance reference of your remote
control.
1
3
4
8
9
10
14
15
16
17
1
To select device mode (T/R/D)*
2
For On/Standby mode (T/R/D)
3
Number buttons (T/R/D)
4
To select Audio Description mode on/off (T)
5
To select external input sources (T)
To select line input (R/D)
6
To switch between ATV (analogue television) and DTV
(digital television) (T)
To display Contents menu (R)
7
To change programme positions (T/R)
To change text pages (T)
2
5
6
7
11
12
13
18
19
20
8
To alter the TV volume (T/R/D)
9
To mute the TV sound (T/R/D)
10
To display the
To access Top Menu (R/D)
11
To exit Menus (T)
To return to previous Menu (R/D)
12
When using menus the arrows move the cursor on the
screen up, down, left or right.
(T/R/D)
13
To switch between TV, Radio and Favourite programmes
when in
To access Setup menu (R/D)
14
On-screen Menus (T)
DVD Menus (R/D)
15
Text and interactive service control buttons (T)
To work interactive service control on device (R)
16
Selectable picture preferences (T)
17
Widescreen viewing (T)
18
To display on-screen information (T/R/D)
To access index page in Text mode (T)
19
To call up text services in
services in
20
When in TV mode:
D
r
s
SUBTITLE Digital Subtitles or Analogue TEXT Subtitle
When in Text mode:
l
A
B
C
D
When using the Programme Guide:
Z
– 24 hours
z
+ 24 hours
CC
– 1 page
cc
+ 1 page
REGZA-LINK or DVD mode:
press W/w to PAUSE/STEP
press
press
press
press
press
press
press
* T=TV mode, R=REGZA-LINK mode, D=DVD mode
digital
on-screen Programme Guide (T)
Q
to confirm your selection
digital
mode
mode (T)
analogue
digital
Analogue time display
Picture still
Stereo/bilingual transmissions
pages if available
To access Sub pages
To reveal concealed text
To hold a wanted page
To enlarge text display size
To select a page whilst viewing a normal
picture
c
to PLAY
CC
to REWIND
cc
to FAST FORWARD
V
to EJECT
v
to STOP
Z
to SKIP-REWIND
z
to SKIP-FORWARD
mode and interactive
6
SETTING UP
Inserting batteries and effective range of
the remote
Remove the back cover to reveal
the battery compartment and
make sure the batteries are
inserted the right way round.
Suitable battery types for this
remote are AAA, IEC R03 1.5V.
Do not combine a used, old
battery types. Remove dead batteries immediately to prevent
acid from leaking into the battery compartment. Dispose of
them in a designated disposal area.
not be exposed to excessive heat such as sunshine, fire or the
like.
The performance of the remote control will deteriorate beyond
a distance of five metres or outside an angle of 30 degrees
from the centre of the television. If the operating range
becomes reduced the batteries may need replacing.
battery with a new one or mix
Warning:
batteries must
7
SETTING UP
Connecting external equipment
Before connecting any external equipment, turn off all main power switches. If there is no switch
remove the mains plug from the wall socket.
OPTICAL DIGITAL AUDIO OUTPUT (DTV MODE ONLY)
HDMI™ INPUT
SOCKETS
COMPONENT VIDEO INP UT (EXT3)
SCART 2 (EXT2)
SCART 1 (EXT1)
*a decoder could
be Digital Satellite or
any other compatible
decoder.
decoder*
media recorder
Aerial cables:
Connect the aerial to the socket on the rear of the television.
If you use a decoder* and/or a media recorder it is essential
- - - - - - - - - - - - - - - - - - - - - -
that the aerial cable is connected through the decoder and/or
through the media recorder to the television.
SCART leads:
Connect the video recorder
Connect the decoder
media recorder
Before running
recorder to
The phono sockets alongside the COMPONENT VIDEO INPUT
sockets will accept L and R audio signals.
. . . . . . . . . . . . . . . . . . . . . . . . . .
IN/OUT
TV
SAT
socket to the decoder
Auto tuning
Standby
.
socket to the television. Connect the
socket to the television.
put your decoder and media
MEDIA REC
. socket.
The Digital Audio Output socket enables the connection of a
suitable surround sound system.
NOTE: this output is always
active.
HDMI™ (High-Definition Multimedia Interface) is for use with
a DVD, decoder or electrical equipment with digital audio and
video output. It is designed for best performance with 1080i
and 1080p high-definition video signals but will also accept
and display VGA, 480i, 480p, 576i, 576p and 720p signals.
FIXING STRAP
POWER switch
NOTE:
Although this television is able to connect to HDMI
equipment it is possible that some equipment may not operate
correctly.
A wide variety of external equipment can be connected
to the back of the television, therefore the relevant
owners manuals for
referred to.
We recommend
all
additional equipment must be
SCART 1
for a decoder and
SCART 2
for a
media recorder.
If connecting S-VIDEO equipment, set the
See
page 35
.
If the television automatically switches over to monitor external
equipment, return to normal television by pressing the desired
INPUT
for
EXT2
.
programme position button. To recall external equipment,
press
o
to select between
HDMI2, HDMI3, PC
DTV, EXT1, EXT2, EXT3, HDMI1
or
ATV
.
,
HDMI, the HDMI logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
8
SETTING UP
Connecting an HDMI™ or DVI
device to the HDMI input
The HDMI input on your television receives digital
audio and uncompressed digital video from an
HDMI source device, or uncompressed digital video
from a DVI (Digital Visual Interface) source device.
This input is designed to accept HDCP (High-Bandwidth
Digital-Content Protection) program material in digital form
from EIA/CEA-861-D–compliant
devices (such as a set-top box or DVD player with HDMI or DVI
output). For acceptable video signal formats, see page 47.
NOTE:
• Some early HDMI equipment may not work properly with
your latest HDMI TV, due to the adoption of a new standard.
Please unplug your HDMI cable first and then try setting the
Lip Sync
to “
Off
”. Your early HDMI source should operate
properly with your television. See page 36.
• Supported Audio format: Linear PCM, sampling rate 32/
44.1/48kHz.
To connect an HDMI device
Connect an HDMI cable (type A connector) to the HDMI
terminal.
For proper operation, it is recommended that you use an HDMI
cable with the HDMI Logo ( ).
• If your HDMI connection is capable of 1080p and/or your
television is capable of refresh rates greater than 60Hz, you
will need a Category 2 cable. Conventional HDMI/DVI cable
may not work properly with this mode.
• HDMI cable transfers both video and audio. Separate analog
audio cables are not required (see illustration).
• See “HDMI1 audio” on page 36.
The HDMI3 terminal is located at the side of the television.
[1]
consumer electronic
To connect a DVI device
Connect an HDMI-to-DVI adapter cable (HDMI type A
connector) to HDMI1 terminal and audio cables to the PC/
HDMI1 (AUDIO) socket (see illustration).
• The recommended HDMI-to-DVI adapter cable length is 6.6
ft (2m).
• An HDMI-to-DVI adapter cable transfers video only.
Separate analog audio cables are required.
• See “HDMI1 audio” on page 36.
Audio cable for HDMI to
television connection
(not supplied)
HDMI-to- DVI adapter Cable
DVI device
VIDEO AUDIO
LR
IN
OUT
R
L
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is
recommended that you follow these procedures:
• When turning on your electronic components, turn on the
television first, and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device first, and then the television.
DVI/HDCP
OUT
HDMI cable
HDMI device
VIDEO AUDIO
LR
IN
OUT
R
L
To view the HDMI device video, press the
HDMI2 or HDMI3 mode.
HDMI OUT
o
to select HDMI1,
[1] EIA/CEA-861-D compliance covers the transmission of uncompressed
digital video with high-bandwidth digital content protection, which is
being standardized for reception of high-definition video signals. Because
this is an evolving technology, it is possible that some devices may not
operate properly with the television.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered t rademarks of HDMI Licensing LLC.
9
SETTING UP
REGZA-LINK connection
You can control the basic functions of connected audio/video devices using the televisions remote control
if you connect a REGZA-LINK compatible AV amplifier or playback device. For an explanation of setup and
operations, see pages 37–38.
AV amplifier
VIDEO
AUDIO
LR
R
L
IN
OUT
HDMI OUTHDMI
IN
Playback device
VIDEO
AUDIO
LR
R
L
IN
OUT
HDMI OUT
For the setup shown above, you will need three HDMI cables
(see page 9).
NOTE:
• If several devices are connected, the REGZA-LINK feature
may not operate properly.
• For proper operation, it is recommended that you use HDMI
cables with the HDMI Logo ( )
• The HDMI3 terminal is located at the side of the television.
Playback device
VIDEO
AUDIO
LR
R
L
IN
OUT
HDMI OUT
Before controlling the device(s):
• After completing the above connections, set the REGZA-LINK
menu as you desire (see page 37).
• The connected devices must also be set. For details, see the
operation manual for each device.
• The REGZA-LINK feature uses CEC technology as regulated
by the HDMI standard.
• This feature is limited to models incorporating Toshiba’s
REGZA-LINK. However, Toshiba is not liable for those
operations. Refer to individual instruction manuals for
compatibility information.
10
SETTING UP
Connecting a computer
With either the RGB/PC or HDMI connection, you
can watch your computer’s display on the television
and hear the sound from the televisions speakers.
To connect a PC to the RGB/PC terminal
When connecting a PC to the RGB/PC terminal on the
television, use an analog RGB (15-pin) computer cable and a
PC audio cable to the PC/HDMI1 (AUDIO) socket. Select
from the
PC/HDMI1 audio
menu located in the
SET UP
options in the
menu.
AV connection
the back of your television
Mini D-sub
15 pin connector
Computer
Audio cable for PC to
television connection
(not supplied)
RGB PC cable
(not supplied)
PC
• When PC input mode is selected some of the television’s
features will be unavailable e.g.
UP
menu,
Picture settings
• If connecting a certain PC model that signal is particular, the
PC signal may not be detected correctly.
Colour, Tint, DNR
menu.
Manual setting
and
Black/White Level
To connect a PC to the HDMI terminal
When connecting a PC to the HDMI terminal on the television,
use an HDMI-to DVI adapter cable and analog audio cables.
If connecting a PC with an HDMI terminal, use an HDMI cable
(type A connector). Separate analog cables are not necessary
(see page 9).
the back of your television
Computer
HDMI-to-DVI
adapter cable
in the
SET
in the
Audio cable for
PC to television
connection
(not
supplied)
Conversion
adaptor if required
(not supplied)
To use a PC, set the monitor output resolution on the PC before
connecting it to the television. For acceptable video signal
formats, see page 46.
To display the optimum picture, use the PC setting feature (see
page 34).
NOTE:
• The PC audio input terminals on the television are shared
with the HDMI1 analog audio input terminals (see page 36).
• Some PC models cannot be connected to this television.
• An adapter is not needed for computers with a compatible
mini D-sub15-pin terminal.
• Depending on the DVD’s title and the specifications of the PC
on which you are playing the DVD-Video, some scenes may
be skipped or you may not be able to pause during multiangle scenes.
• A band may appear at the edges of the screen or parts of the
picture may be obscured. This is due to scaling of the picture
by the set, it is not a malfunction.
For acceptable PC and video signal formats, see page 47.
NOTE:
• The edges of the images may be hidden.
• If connecting a certain PC model that signal is particular, the
PC signal may not be detected correctly.
11
SETTING UP
Controls and input connections
A wide variety of external equipment can be connected to the input sockets on the side of the television.
Whilst all the necessary adjustments and controls for the television are made using the remote control, the
buttons on the television may be used for some functions
.
Standby
POWER switch
Input 3 (side) will take
pr io ri ty ov er EX T3 (b ack ) i f b ot h
connections are used at the
same time.
GREEN LED - Active standby
digital
only)
(
Switching on
If the RED LED is unlit check that the mains plug is connected
to the power supply and press the
left side of the television to switch the television on. If the
picture does not appear press
take a few moments.
To put the television into Standby press
control, the GREEN active standby LED will appear (
‘Software Upgrade’ section
then disappear. To view the television press
picture may take a few seconds to appear.
!
(POWER) button on the
1
on the remote control, it may
1
on the remote
) next to the RED for a few moments
1
again. The
see
Using the remote control
Press
M
on the remote control to see the menus.
In
digital
mode the menu bar at the top of the screens will
show three different topics shown in symbols. As each symbol
is selected by pressing the
control, its respective options will appear below.
C
or c button on the remote
COMMON INTERFACE
The Common Interface is for a
Conditional Access Module
(CAM).
Contact a service provider.
HDMI3
INPUT
INPUT 3
(EXT3)
RED LED – Standby
GREEN LED – Power on
In
analogue
each symbol is selected by pressing
ring on the remote control, its respective options will appear
below.
To use the options, press
move up and down through them and
required choice. Follow the on-screen instructions. The
functions of each menu are described in detail throughout the
manual.
mode the menu appears as a list of six topics. As
C
or c on the navigation
B
and b on the remote control to
Q
, C or c to select the
Using the controls and connections
To alter the volume press –
To alter the programme position press
Press
MENU
options.
Press
An S-video cable provides better picture performance than a
composite video cable. If you connect an S-video cable to
EXT3
cable or the picture performance will be unacceptable.
To select the external input, press
input source is selected as described on
Please always refer to the owner’s manual of the equipment to
be connected for full details.
and I, i, U or u to control the sound and picture
MENU
twice to finish.
, be sure to disconnect the standard (composite) video
2
+.
o
until the appropriate
b p B
page 35
.
.
12
TUNING THE TELEVISION
Tuning Digital television
Before switching on the television put your decoder
and media recorder to
connected.
To set up the television use the buttons on the
remote control as detailed on page 6.
Tuning for the first time
a
Press the 1 button, the
appear. This screen will appear the first time that the
television is switched on and each time the television
is reset.
Country UK
Language ENGLISH
Audio Language ENGLISH
Audio Output PCM
Subtitles OFF
Local Time Settings 0
Continue
b
Press b to highlight
television will now tune the stations for your country.
c
Using b highlight
Standby
LOCAL OPTIONS
LOCAL OPTIONS
Country
and C or c to select. The
Language
, then C or c to select.
if they are
screen will
When the search is complete the television will
automatically select programme one.
The
AUTO TUNING
screen will display the total
number of services found.
AUTO TUNING
94 programmes found
58 TV 27 Radio 9 Text
Press OK to watch programme
Prog. Name Type UHF Quality
BBC ONE GOOD
134
2 34
BBC TWO
3 31
ITV1
4 31
Channel 4 POOR
5 48
Five
6 31
ITV2
Change Watch
Page Up Page Down Sort
e
Use b or B to move through the list to select a
programme then press
NOTE:
The time will be set automatically by
transmission but can be advanced or decreased by up
to 3 hours using
Q
to view.
Local Time Settings
GOOD
GOOD
GOOD
POOR
.
d
Press Q to start tuning.
The
AUTO TUNING
screen will appear and the
television will start to search for available stations. The
progress bar will move along the line.
You must allow the television to complete the
Progress
Prog. Name Type UHF Quality
CBBC Channel GOOD
70 34
Community POOR
87 21
EXIT
Cancel
search.
AUTO TUNING
13
TUNING THE TELEVISION
Digital
NOTE:
As new services are broadcast it will be necessary to re-
auto tuning
tune the television in order to view them.
Auto tuning
It is recommended that Auto tuning is run periodically to
a
b
will completely re-tune the television and can be
used to up date the channel list.
ensure that all new services are added
programmes and settings, i.e. favourites and locked
Press M, the
Use
programmes, will be lost.
SETUP MENU
b
to highlight
Auto tuning
. All current
will appear.
. Press Q.
A screen will appear warning that previous digital
programmes and settings will be deleted.
Press
Q
to continue with the
WARNING
!
All previous digital programmes and
settings will be deleted.
Continue?
Select Cancel
MENU
YES
Auto tuning
.
The television will start to search for all available
stations.
AUTO TUNING
Progress
Prog. Name Type UHF Quality
CBBC Channel GOOD
70 34
87
Community POOR
21
You must allow the television to complete the
search.
When the search is complete the
Auto tuning
screen
will display the total number of services found.
AUTO TUNING
94 programmes found
58 TV 27 Radio 9 Text
Press OK to watch programme
Prog. Name Type UHF Quality
BBC ONE GOOD
1
BBC TWO
2
ITV1
3
Channel 4
4
Five
5
ITV2
6
Change Watch
Page Up Page Down Sort
c
Use b or B to move through the list to select a
programme then press
Analogue
digital
This is a
of both
lifetime of this set it is very likely that
be switched off to allow for more new
television which is integrated to allow the use
digital
and
analogue
services. However, during the
34
34
31
31
48
31
MENU
Back
Q
to view.
switch-off
analogue
digital
GOOD
GOOD
POOR
GOOD
POOR
services will
services.
This ‘switch-off’ will happen in a number of phases, which will
be a dv er ti se d i n your area well in advanc e. It is recomm ended
that at each phase the television is re-tuned to ensure that
existing and new
disruption (
see the
digital
services can be viewed without
'Auto tuning'
section
).
EXIT
Cancel
14
TUNING THE TELEVISION
Digital
NOTE:
When the television is switched off the mode being
viewed at the time will automatically be selected when the
television is switched back on.
a
The station order may be changed to suit personal
preference. Press
on screen.
b
Use b to move down through the list and highlight
Programmes
TV Setup
Local Options
Auto tuning
Manual tuning
Programmes
MENU EXIT
c
With the list of stations now showing use b or B to
highlight the station you want to
The selected station will be moved to the right of the
screen.
Prog. Name
programme sorting
M
, the
SETUP MENU
. Press Q.
SETUP MENU
Back Watch TV
move
PROGRAMMES
1
BBC ONE
2
BBC TWO
3
ITV1
4
Channel 4
5
Five
6
ITV2
Sort Store Back Watch TV
Page Up Page Down
MENU EXIT
will appear
OK
OK
OK
OK
OK
and press c.
Digital
This feature is available for service engineers or can be
used for direct channel entry if the multiplex channel
a
Select
Manual tuning
press
Q
b
Enter the multiplex number using the number buttons
and then press
search for that multiplex.
When the multiplex is found any channels not currently
on the programme list will be added and the
programme information at the top of the screen will be
updated.
c
Repeat as necessary. Press P to finish.
manual tuning
is known.
.
from the
Q
. The television will automatically
SETUP MENU
and
d
Use b or B to move through the list to your
position. As you do so the other stations will move to
make room.
e
Press C to store your move. Repeat as necessary, then
press
P
.
preferred
15
TUNING THE TELEVISION
Tuning Analogue mode
Quick Setup
The
Quick Setup
currently available in the area. To put the television into
mode press the
a
b
c
d
e
Select
ATV/DTV
ATV
feature will tune all
button.
mode. The
analogue
Quick Setup
channels
screen will
appear.
Quick Setup
Select your language.
Language English
EXIT
Watch TV
Using C or c select your
Then press C or c to select your
To start
Auto tuning
Searching
Channel : C22 Station : BBC1
EXIT
Stop
press Q.
Auto tuning
OK
language
country
Next
, then press Q.
.
The search will begin for all available stations.
The slide bar will move along the line as the search
progresses.
You must allow the television to complete the
search.
When the search is complete the television will
automatically select programme position 1 and the
Manual tuning
screen will appear.
Prog. Channel Station
OK
Select Sort
MENU EXIT
Manual tuning
1 C22 BBC1
2 C28 BBC2
3C25ITV
4 C32 CH4
5C68
6C69
Back Watch TV
ATV
f
Use b or B to move through the list to select a
programme then press
The station order may be changed using the
tuning
screen (
positions’ section
see the
).
P
to view.
analogue
‘Sorting programme
Manual
16
Manual tune
The television can be tuned-in manually using
. For example: if the television cannot be connected to
tuning
a media recorder/decoder with a SCART lead or to tune-in a
station on another
Use C and c to move across the screen and select any of these
Manual Tune options.
OK
MENU
System
.
Manual tuning
EXIT
System
Watch TV
0 I A C 60 0
Store
Back
123 4 5 6 7 8
1
Programme:
The number to be pressed on the remote control.
2
System:
Specific to certain areas.
3
Colour system:
Factory set to Auto, should only be changed if problems
are experienced, i.e. NTSC input from external source.
4
Programme skip:
8
means nothing has been stored or the facility to skip
the channel is ON. See page 18.
5
Channel:
The channel number on which a station is being broadcast.
6
Search:
Search up and down for a signal.
7
Manual fine tuning:
Only used if interference/weak signal is experienced. See
page 41.
8
Station:
Station identification. Use the B or b and C or c buttons
to enter up to seven characters.
To allocate a programme position on the television for a
decoder and media recorder: turn the decoder on, insert a
pre-recorded film in the media recorder and press PLAY, then
manually tune.
Manual
V C R
TUNING THE TELEVISION
a
Press M and using C or c select the
with
b
highlight
Manual tuning
SET UP
Language English
Country UK
Auto tuning
Manual tuning
AV
connection
Picture position
MENU EXIT
Back Watch TV
b
Use B or b to highlight the programme position
required
e.g.
we suggest
Prog. 0
Manual tuning
Prog. Channel Station
0 C60
1 C22 BBC1
2 C28 BBC2
3 C25 ITV
4 C32 CH4
5 C69
OK
Select Sort
MENU
Back
Different
c
Press Q to select. If the programme is skipped,
Programme skip
0 I A C 60 0
OK
Store
MENU
Back
d
Press c to select
EXIT
Watch TV
Channel
numbers may be displayed.
must be removed before storing.
Manual tuning
System
EXIT
Watch TV
System
and use B or b to change if
required.
SET UP
menu,
, press Q to select.
1/2
OK
OK
OK
OK
for a media recorder.
17
e
Then press c to select
f
Press B or b to begin the search. The search symbol
Search
.
will flash.
Manual tuning
EXIT
Search: Up
Watch TV
0 I A C 60 0
OK
Store
MENU
Back
TUNING THE TELEVISION
g
Each signal will show on the television, if it is not your
media recorder, press
B
or b again to restart the
search.
h
When your media recorder signal is found, press c to
move along to
required characters,
0 I A C 60 0 V C R
OK
Store
MENU EXIT
i
Press Q to store.
j
Repeat for each
tune or, press
Station
. With B, b, C and c put in the
e.g. VCR
Manual tuning
Station
Back Watch TV
programme position
M
to return to the list of channels and
.
select the next number to tune.
k
Press P when you have finished.
l
To name external equipment,
o
to select o2, then select
SET UP
menu.
m
Press c to select
Label
e.g.
DVD on EXT2, press
Manual setting
then using B, b, C and c put
in the required characters.
Manual setting
Label
EXT2 A D V D
OK
Store
MENU EXIT
Back Watch TV
PLEASE NOTE
This television has direct channel entry if the channel
numbers are known.
Select the
Manual tuning
Programme number
the
standard (terrestrial) channels or
channels and the
screen in
, the
Channel
number. Press Q to
System
S
for cable
store.
you want to
from the
Step 3
. Enter
, then C for
Programme skip
To prevent certain programmes from being viewed, the
programme position can be skipped. The remote control must
be removed as the channels will still be available using the
number buttons. Programmes can then be watched as normal
using the controls on the television, but the television will not
a
b
c
d
e
show the skipped programme position.
Select
Manual tuning
Prog. Channel Station
1 C22 BBC1
2 C28 BBC2
3C25ITV
4 C32 CH4
5C68
6C69
OK
Select Sort
MENU EXIT
Back Watch TV
from the
Manual tuning
SET UP
menu.
Use B or b to highlight the programme position to be
skipped and press
Press c to select
Use B or b to turn
Press
Q
8
on the screen indicates a skipped programme
.
Q
to select.
Programme skip
Programme skip
.
on.
position.
Manual tuning
1 I A C 22 0 B B C 1
OK
Store
MENU EXIT
Back Watch TV
Press M and repeat from
Each programme position has to be
selected. To turn
Programme skip : On
Step 2
Programme skip
or press P.
individually
off, repeat the
procedure for each position.
Skipped programme positions
PU and
Pu or by the controls on the television, but
can
still be accessed by the number buttons on the
cannot
be selected by
remote control.
18
TUNING THE TELEVISION
Sorting programme positions
Channels may be moved and stored on the programme position
a
Select
b
With the list of stations now showing use B or b to
highlight the station you want to
The selected station will be moved to the right of the
screen.
c
Use B or b to move through the list to your
position. As you do so the other stations will move to
make room.
d
Press C to store your move.
Repeat as necessary, then press
of your choice.
Manual tuning
Prog. Channel Station
1 C22 BBC1
2 C28 BBC2
3 C25 ITV
4 C32 CH4
5C68
6C69
Store
MENU
Back
from the
Manual tuning
EXIT
Watc h TV
SET UP
move
P
.
menu.
and press c.
preferred
Using Auto tuning
a
To set up the television using
and use
C
or c to select the
Language English
Country UK
Auto tuning
Manual tuning
AV connection
Picture position
MENU EXIT
Back Watch TV
b
Press b to highlight
c
Using b highlight
Country
television will now tune the stations for your country.
d
Press b to highlight
Auto tuning
!
Previous settings will be lost !
Press EXIT for no change.
Press OK to start Auto tune.
MENU EXIT
Back Watch TV
Auto tuning
SET UP
menu.
SET UP
OK
OK
OK
OK
Language
and C or c to select.
, then C or c to select. The
Auto tuning
, then press Q.
, press M
1/2
e
To start
Auto tuning
press Q.
You must allow the television to complete the search.
When the search is complete the television will automatically
select programme position 1. This may not be a clear picture,
so the station order can be changed
(see ‘Sorting programme
positions’ section).
19
CONTROLS AND FEATURES
General controls
Selecting programme positions
To select a programme position use the numbered buttons on
the remote control.
Programme positions can also be selected using
To display on-screen information
input mode or stereo/mono signal, press . Press again to
cancel.
The Time Display –
The time display facility allows the current (text service) time to
Press
see a time display from the broadcaster. It will remain on
screen for about 5 seconds.
be seen on the television screen.
D
whilst watching a normal television broadcast to
i.e.
programme position,
analogue
Stereo and Bilingual transmissions
If stereo or dual language broadcasts are transmitted the word
Stereo or Dual will appear on the screen each time programme
positions are changed, disappearing after a few seconds. If the
broadcast is not in stereo the word Mono will appear.
Stereo…
Press s to select
Bilingual…
transmitted the word
programme number and if the word
s
Bilingual transmissions are rare. If they are
to select
Dual 1, Dual 2
Stereo
Dual
will display. Choose the required
Dual
or
Mono
or
Mono
appears press
.
PU and
only
.
Pu.
c
In
analogue
SOUND
Dual Dual 1
Headphone Mode1
Headphone Level
Bass
Treble
Balance
MENU EXIT
d
Press b to highlight
or
mode, press M and C or c to select
.
SOUND
Back Watch TV
c
to change the setting.
Bass, Treble
or
0
0
0
Balance
1/2
and C
Bass boost
Bass boost
speakers. The difference will only be noticeable on sound with
a
b
enhances the depth of the sound on the TV
a strong bass.
In the
SOUND
Use
Then press b to highlight
C
or c adjust to suit your preference.
menu press b to highlight
C
or c to select On.
Bass boost level
Bass boost
and using
.
Sound controls
Volume controls and mute sound
Volume
Press Y or y to adjust the volume.
Sound Mute
Press once to turn the sound off and again to cancel.
Bass, Treble and Balance
The sound controls are accessible in
modes, as are most of the televisions features.
a
In
digital
mode, press M and using b highlight
Setup
then press Q.
b
Use C or c to select
SOUND
digital
.
and
analogue
SOUND
WOW
Stable sound Off
Bass boost
Bass boost level
MENU EXIT
Back Watch TV
When an active Super Woofer is connected to the Woofer Out
connection on the back of the television, select
in the
SET UP
menu, press b to highlight
External
. (See 'Input Selection and AV
section
).
TV
C
or c select
Connections'
20
OK
On
70
AV connection
Woofer
and using
2/2
Loading...