Toshiba 37A3030D Schematic

SERVICE MANUAL
Стр. 1 из
1
05.05.2015
file://C:\Program Files\zeus\js\!!fcover.html
LCD Color Television
37A3030D
Ver. 2.00
This model is classified as a green product (*1), as indicated by the underlined serial number. This
Service Manual describes replacement parts for the green product. When repairing this green
For (*1) and (*2), refer to
© TOSHIBA CORPORATION
GREEN PRODUCT PROCUREMENT
and
LEAD-FREE SOLDER
.
ADJUSTMENT
↓↓↓↓
↓↓↓↓
Стр. 1 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Service Mode
Entering to Service Mode
1. Set VOLUME to minimum and press button once on remote control.
Service Mode display
2. Press button again and hold button down.
3. While holding the button, press MENU button on TV set.
Стр. 2 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Displaying the Adjustment Menu
Press MENU button on TV.
Service Mode
Press
Adjustment Mode
↑↑↑↑ ↓↓↓↓
Press
Key Function in the Service Mode
The following key entry during display of adjustment menu provides special functions.
CAUTION: Never try to perform initialization unless you have changed the
memory IC.
button (on remote control)
Never adjust H.POS and V.POS except PAL/WIDE mode.
Test signal selection
Стр. 3 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Selection of the adjustment items CH (on TV or remote control)
Change of the data value Volume +/- (on TV or remote control)
Adjustment menu mode ON/OFF MENU button (on TV)
Initialization of the memory (QA02) CALL + CH button on TV
Reset the count of operating
protect circuit to "00"
Turn off I2C bus communication CALL + Volume + button on TV
"RCUT" selection 1 button
"GCUT" selection 2 button
"BCUT" selection 3 button
"CNTX" selection 4 button
"COLC" selection 5 button
"UVTT" selection 6 button
Automatic A/D Adjustment
(PC, Component, Composite (PAL, NTSC))
Self diagnostic display ON/OFF 9 button
CALL + CH button on TV
7 button
Selecting the Adjusting Item
Every pressing of CH button in the service mode changes the adjustment items in the order of table below. ( button for reverse order)
SETTING & ADJUSTING DATA
[ SERVICE MODE ]
ADJUSTING ITEMS AND DATA IN THE SERVICE MODE:
Note:
The image system data of RCUT-BDRV is different by each image format.
The PAL value is indicated in the table.
Стр. 4 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Item Name of adjustment
RCUT R CUT OFF
GCUT G CUT OFF
BCUT B CUT OFF
RDRV R DRIVE
GDRV G DRIVE
BDRV B DRIVE
BRTC BRIGHTNESS CENTER
COLC COLOR CENTER
UVTT BASE BAND TINT
CNTX CONTRAST MAX
VOLUX MAX VOLUME LIMITED
PLLW0 PLL WAIT TIME
PLLW1 PLL WAIT TIME
PLLW2 PLL WAIT TIME
PLLW3 PLL WAIT TIME
PLLW4 PLL WAIT TIME
PLLW5 PLL WAIT TIME
OPT1 TV SET OPTION 1
OPT2 TV SET OPTION 2
OPT3 TV SET OPTION 3
OPT4 TV SET OPTION 4 (PANEL OPT DATA FOR VENDOR)
OPT5 TV SET OPTION 5 (PANEL OPT DATA FOR SIZE)
OPT6 TV SET OPTION 6 (HOTEL MODE)
OPT7 TV SET OPTION 7 (HOTEL MODE)
OPT8 TV SET OPTION 8 (HOTEL MODE)
TVOP TV SET OPTION
ID MODEL ID
BDWID BORDER WIDTH FOR EXACT SCAN
BDHIT BORDER HEIGHT FOR EXACT SCAN
FPLG MASK_ENABLE (SD/HD)
FPLG2 Channel LOGO Vector Clip SW (SD)
Стр. 5 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
FPLG3 Channel LOGO Vector Clip SW (HD)
Factory preset data will be loaded after setting Model ID data.
(Refer to Initialization of Memory Data of QA02 and setting data of signal board.)
Adjusting the Data
Pressing of VOLUME +/- button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item.
I2C Bus Off
Turn off I2C communication between IC700 and IC400.
1) Press and hold the CALL button on the remote control, then press the Volume + button on the TV.
2) Display "BUS Off" OSD.
3) I2C communication turned off.
Note:
To return Bus on status, press and hold the CALL button on the remote control, then press the Volume + button on the TV again. TV will be turned off and automatically turned on, then status will be Bus On.
Setting TVOP
Enter to service mode and select menu of TVOP by pressing P or P during display of adjustment menu. After selecting TVOP, press + or - to set I2C check function to
disable or enable as below.
TVOP FUNCTION DESCRIPTION 1 0 (Normal)
D5 (bit5) I2C check between IC700 and IC400. (WDT) Disable Enable
Стр. 6 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Setting Panel Option Data
Panel option data is subject to OP4 and OP5. Enter to service mode and select menu of OPT4 or OPT5 by pressing P or P during
display of adjustment menu. After selecting OPT4 or OPT5, press + or - to set OPT4 or OPT5 value as table below.
Panel option data
Series Model name Panel vendor OPT4 value OPT5 value
A3000 EU Digital/Ready 26A3030D/A3000P LPL 0x01 0x03
IPS 0x07 0x03
32A3030D/A3000P LPL 0x01 0x05
IPS 0x07 0x05
37A3030D/A3000P LPL 0x01 0x06
IPS 0x07 0x06
42A3030D/A3000P LPL 0x01 0x07
OP4
Ex. OPT4 value 0x05 indicates that panel vendor is AUO AMVA.
OPT4
Panel vendor LPL - - - - 0 0 0 1
SHP - - - - 0 0 1 0
CMO - - - - 0 0 1 1
AUO PMVA - - - - 0 1 0 0
D7
(bit7)
D6
(bit6)
D5
(bit5)
D4
(bit4)
D3
(bit3)
D2
(bit2)
D1
(bit1)
(bit0)
D0
AUO AMVA - - - - 0 1 0 1
SAMSUNG - - - - 0 1 1 0
IPS - - - - 0 1 1 1
OP5
Ex. OPT5 value 0x05 indicates that panel size is 32.
Стр. 7 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
OPT5
Size 32 - - - - 0 1 0 1
37 - - - - 0 1 1 0
42 - - - - 0 1 1 1
D7
(bit7)
D6
(bit6)
D5
(bit5)
D4
(bit4)
D3
(bit3)
D2
(bit2)
D1
(bit1)
(bit0)
Convert from Bit (Binary) to Hex
The table for converting from bit (D7-D0) to hex (0x**).
BIT (Binary)
High nibble
Low nibble
D7 D6 D5 D4
D3 D2 D1 D0
D0
HEX
0
1
2
3
4
5
6
7
8 1
9 1
A 1
B 1
C 1 1
D 1 1
0 0 0 0
0 0 0
0 0
0 0
0
0
0
0
1
1 1
1
1
1 1
1 1 1
0 0 0
0 0
0
0
0 0
0
1
1 1
0 0
0
1
0
1
0
1
0
1
E 1 1 1
F 1 1 1 1
0
E.g. If Bit D7-0 = 0101 1010, Hex data is 0x5A.
Стр. 8 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Exit from Service Mode
Pressing POWER button to turn off the TV once.
Initialization of Memory Data of QA02 and Setting Data of Signal Unit
After replacing QA02 or signal board, the following initialization is required.
CAUTION: Never attempt to initialize the data unless QA02 has been
replaced.
Whenever using new signal board to the set, setting the Model ID data
according to Panel option data.
1) Enter the service mode.
2) Select menu of ID by pressing P or P during display of adjustment menu in the service mode.
3) Change ID data into MODEL ID to initialize by pressing + or -., refer to table below.
4) Press and hold the CALL button on the remote control, then press the CHANNEL
button on the TV.
5) Initialization progress dialog including model name and panel vendor is shown.
Progress status is "WRITING".
6) Progress status is changed "OK" and power cycle (automatically). Then QA02
initialization has been completed.
7) Enter the service mode and select version check mode. Confirm if model name and
model id set is correct. If not, repeat steps 1) to 6).
Note:
Стр. 9 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
In case initialization by setting wrong MODEL ID is done, there is a possibility of
abnormal display.
8) Set I2C check function of TVOP to enable.
9) Check the picture carefully. If necessary, adjust any adjustment item above.
Perform "Auto tune" on the owner's manual.
MODEL ID (HEX) Model name Panel vendor
0x01 26A3000P LPL
0x02 26A3000P IPS
0x03 32A3000P LPL
0x04 32A3000P IPS
0x05 37A3000P LPL
0x06 37A3000P IPS
0x07 42A3000P LPL
0x08 26A3030D LPL
0x09 26A3030D IPS
0x10 32A3030D LPL
0x11 32A3030D IPS
0x12 37A3030D LPL
0x13 37A3030D IPS
0x14 42A3030D LPL
0x15
0x16
0x17
0x18
0x19
0x20
0x21
0x22
0x23
0x24
0x25
0x26
Стр. 10 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
0x27
0x28
0x29
0x30
0x31
0x32
0x33
Initializing Data setting flowchart after replacing the Signal Unit
Стр. 11 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
Test Signal Selection
Every pressing of button on the remote control changes the built-in test patterns on
Стр. 12 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
screen as described below in Service Mode.
Picture Signal
Red raster
Green raster
Blue raster
All Black
All White
Self Diagnostic Function
1. Press "9" button on remote control during display of adjustment menu in the service
mode. The diagnosis will begin to check if interface among IC's is executed properly.
2. During diagnosis, the following displays are shown.
* Self check display and Item are subject to the models.
NG is abnormal (Red indication).
Стр. 13 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
(1) Firmware :
Version information of microprocessor
Series name (AAAA) and market area (BB) and software program version (0000)
(2) Time : Total hour of turn the TV on. (Unit : H)
(3) BL_STATUS :
Counter for saving BackLight on error.
This value is counted till 99 (Decimal).
(4) Bus line : -- "OK" is normal
SCL-GND (Red indication) : SCL-GND short circuit
SDA-GND (Red indication) : SDA-GND short circuit
SCL-SDA (Red indication) : SCL-SDA short circuit
(5) Bus cont : --- "OK" is normal.
When the abnormal status is detected, type name of semiconductor is
indicated in red colour.
(6) Block
UV : TV reception mode
V1 - V9 : VIDEO 1-9 input mode
PC : PC mode
YUV : YUV mode
DTV : DTV mode
UV RF
V1
(SCART (FULL))
1
2
V2 (SCART (S+AV))
Стр. 14 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
V3
(Component/Composite)
V4 HDMI1
V5 --
V6 --
V7 --
V8 --
V9 --
PC PC
YUV --
DTV --
3
Version Check Mode
1. Press "9" button twice on remote control during display of adjustment menu in the
service mode.
The version of main MPU will be checked.
2. During Version Check, the following displays are shown.
* Version check display and Item are subject to the models.
Стр. 15 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
(1) MAIN MPU :
Version information of microprocessor
Series name and Code Program Version (4 figure number) and OSD Version (2 figure
number).
(2) EEPROM :
Version information of EEPROM : Display 1 byte data.
(3) SUB MPU :
Version information of SUB MPU : Display 1 byte data.
(4) OPTION :
Option information : Display six numbers of 1 byte data.
(5) HDMI ID :
HDMI ID information : Display 4 byte data.
(6) SW Ver
Version information of DB software as Toshiba release. (Only digital model.)
(7) MW Ver
Left side is Application and UI version information of DB software. (Only digital
model.)
Right side is Firmware (Driver) version information of DB software. (Only digital
model.)
(8) A/D Adjust
NTSC (60 Hz) SD signal (composite input).
Стр. 16 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
A/D adjustment item.
--MAIN : It's enable only in double Window model. A/D adjustment status of main
picture.
--PIP : It's enable only in double Window model. A/D adjustment status of sub
picture.
--COMP : Component input
--PC : PC input
--NTSC :
--PAL : PAL (50 Hz) SD signal (composite input).
--OK : A/D adjustment set correctly.
--NG : A/D adjustment set incorrect.
-- : A/D adjustment is not needed. Because its picture format isn't used.
(9) 100 Hz FPGA Software Version
It's enable only in 100 Hz drive panel model.
Upper 2 figure number means function versions of double frequency convert.
Lower 2 figure number means function version of vector complement.
(10) Memory Data Version
Version information of EEPROM.
DRMA**** means model number of EEPROM.
REV** means version of EEPROM.
(11) CD number
CD information (ascii code). : Display 4 byte data.
(12) Model Name
Model name information (ascii code). : Display 7 byte data.
(13) LCD Panel Vendor information display
The following Panel Vendor (DDD) and screen size (00) are displayed.
Example : AUO-32 indicates that Vendor is AUO and Screen Size is 32 inch
Status Check Mode
1. Press "9" button thrice on remote control during display of adjustment menu in the
service mode.
The status of this model will be checked.
2. During Status Check, the following displays are shown.
* Status check display and Item are subject to the models.
Стр. 17 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
(1) MAIN :
Main source information :
Display RF position number (0 - 99) on the main screen, or Input Source
(EXT1/2/3/HDMI etc.)
(2) MAIN FORMAT :
Display Video and PC format information
(3) MAIN PLL :
Main PLL information : Display 1 byte data at five.
(4) SUB :
Sub source information :
Display RF position number (0 - 99) on the Sub screen, or Input Source
(EXT1/2/3/HDMI etc.)
This item displays only Double window model.
(5) SUB FORMAT :
Display Video and PC format information
This item displays only Double window model.
(6) SUB PLL :
Sub PLL information : Display 1 byte data at five.
This item displays only Double window model.
(7) SCREEN SIZE :
Display the screen size as follows.
Exact Scan
Wide
Super Live 2
Cinema 2
Стр. 18 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
4:3
Super Live 1
Cinema 1
Subtitle
14:9
Note:
Exact Scan is shown only for 1080p panel model with video input mode except pc.
(8) OTHER STATUS :
Other status information : Display three numbers of 2 byte data.
Setting Hotel Mode
Enter to service mode and select Hotel Mode menu by pressing P or P . After selecting Hotel Mode, press + to enter details setting in Hotel Mode.
To select menu, press P or P and press OK to enter the adjustment menu of table bellow. To move the cursor in the adjustment, press + or -.
1. By pressing P or P , OPT2 setting will change the value either 1 or 0 on selected items as follows;
OP2
OPT2 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) - (no use) - -
D6 (bit6) - (no use) - -
D5 (bit5) FRONT Key Disable Enable
D4 (bit4) All keys except input selector key
(Video/TV)
D3 (bit3) User remote control operation Disable
D2 (bit2) Disable SET UP MENU except Disable Enable
Disable Enable
Enable
(Service mode and Supere
User mode may possible to
setting only)
language.
Стр. 19 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
(tuning SETUP MENU)
D1 (bit1) Disable SETUP MENU Disable Enable
(Display the language only)
D0 (bit0) HOTEL Mode On (Enable the setting of D1
from to D7)
Off
(Normal)
VOLUX
Set VOLUX as following.
1) Set speaker volume to 100. (Any value is OK, but 100 is better to check sound level.)
2) Down value of VOLUX until finding suitable sound volume level.
VOLUX FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) ~
D0 (bit0)
Max Limiter of Volume Control 0x00 ~ 0x7F (Normal: 0x7C)
OP6
OPT6 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) Enable mode that POS or VIDEO program
number will be appeared in forced when turn
ON the main power
D6 (bit6) ~
D0 (bit0)
POS or VIDEO program number 0 ~ 127 [decimal] (Normal: 0)
Enable Disable
POS number: 0 ~ 99
VIDEO number: 100 ~ 127
(DTV = 100, VIDEO = 101,
VIDEO = 102..)
100 is used as ATV when
DTV option is disable.
OP7
OPT7 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) Enable mode that speaker volume will be set
in forced when turn ON the main power
Enable Disable
D6 (bit6) ~
Forced speaker volume 0 ~ 100 [decimal] (Normal: 0)
D0 (bit0) Value above 100 is no effect.
Стр. 20 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
OP8
OPT8 FUNCTION DESCRIPTION 1 0 (Normal)
D7 (bit7) ~
D3 (bit3)
D2 (bit2) Enable mode that picture mode will be set in
forced when turn ON the main power
D1 (bit1) ~
D0 (bit0)
Forced picture mode 0 [dec]: Dynamic (mode-1)
- (no use) - -
Enable
(Display the
language only)
(Normal)
1 [dec]: Standard (mode-2)
2 [dec]: Mild (mode-3)
3 [dec]: Memory (mode-M)
Disable
LED Indication
The Green and Red LEDs on the TV (at the bottom center of the TV) indicate the TV's
status, as described below.
Red ON (solid) and Green OFF = The TV power cord is plugged in.
Green ON (solid) and Red ON = The On timer is operating.
1 Green is OFF;
Red blinks continuously at 0.5-
second intervals.
2 Green is OFF;
Red blinks continuously at 1-
second intervals.
LED Indication Condition Solution
Abnormal operation Turn OFF the TV and unplug
the power cord.
Plug the power cord in again
and turn ON the TV.
Abnormal operation of
BUS line.
Turn OFF the TV and unplug
the power cord.
Plug the power cord in again
and turn ON the TV.
Стр. 21 из 21ADJUSTMENT [LCD Color Television] ASIA_EU
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.529\37A
...
FUNCTION AND OPERATION
Стр. 1 из
1
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.487\37A
...
The Remote Control
Simple at-a-glance reference of your remote control.
FUNCTION AND OPERATION
Стр. 1 из
2
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.187\37A
...
Controls and Input Connections
A wide variety of external equipment can be connected to the input sockets on the side of the
television.
Whilst all the necessary adjustments and controls for the television are made using the remote
control, the buttons on the television may be used for some functions.
Switching On
Using the Remote Control
Using the Controls and Connections
Стр. 2 из
2
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.187\37A
...
FUNCTION AND OPERATION
Стр. 1 из
3
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.444\37A
...
Tuning Digital Television for the First Time
Before switching on the television put your decoder and media recorder to
are connected and ensure the aerial is connected. To set up the television use the buttons on
the remote control.
Standby
if they
Стр. 2 из
3
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.444\37A
...
Стр. 3 из
3
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.444\37A
...
FUNCTION AND OPERATION
Стр. 1 из
2
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.421\37A
...
Digital Auto Tuning
Note:
view them.
As new services are broadcast it will be necessary to re-tune the television in order to
Auto Tuning
Стр. 2 из
2
05.05.2015
file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.421\37A
...
Loading...
+ 142 hidden pages