Toshiba 32dt2u, 40FT2U User Manual

Owner’s Manual
Integrated High Definition LCD Television
HIGH-DEFINITION TELEVISION
32DT2U 32DT2UL 40FT2U
For an overview of steps for setting up your new TV, see page 10.
Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider.
© 2011 TOSHIBA CORPORATION All Rights Reserved
The model number and serial number are on of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.
Model number:
Serial number:
the back
Dear Customer,
Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:
The Issue
• The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.
• Flat panel displays that are inappropriately situated on dressers,
bookcases, shelves, desks,
speakers, chests, or carts may fall
over and cause injury.
TOSHIBA Cares!
• The consumer electronics industry is committed to making home
entertainment enjoyable and safe.
Tune Into Safety
One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for proper use of this product.
• Don’t allow children to climb on or play with furniture and television sets.
• Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers.
• Remember that children can become excited while watching a program, especially on a “larger than life” flat panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or knocked down.
• Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be pulled or grabbed by curious children.
Wall Mounting: If you decide to wall mount your flat panel display, always:
• Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount manufacturers.
• If you have any doubts about your ability to safely install your flat panel display, contact your retailer about professional installation.
• Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not designed to be mounted to walls with steel studs or old cinder block construction. If you are unsure, contact a professional installer.
• A minimum of two people are required for installation. Flat panel displays can be heavy.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat Panel Display
Thank you for purchasing this Toshiba LCD TV. This manual will help you use the many exciting features of your new LCD TV. Before operating your LCD TV, please read this manual completely, and keep it nearby for future reference.
Safety Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. See item 25 on page 4.
WARNING:
television, always use a UL Listed wall bracket appropriate for the size and weight of this television. The use of any wall bracket other than a UL Listed wall bracket appropriate for the size and weight of this television for wall mounting this television could result in serious bodily injury and/or property damage. See “Removing the Pedestal Stand” (page 6).
NOTE TO CATV INSTALLERS
This is a reminder to call the CATV system installer’s attention to Article 820-40 of the U.S. NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 32 and 33 on page 4.
WARNING
RISK OF ELECTRIC
SHOCK DO NOT OPEN.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
If you decide to wall mount this
2
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
Do not block any ventilation openings. Install in
7) accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip­over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Wide blade
Additional Safety Precautions
14a) CAUTION:
enclosure surface has been damaged or the TV does not operate normally, take the following precautions:
•
If the TV is dropped and the cabinet or
ALWAYS turn off the TV and unplug the power cord to avoid possible electric shock or fire.
NEVER allow your body to come in contact with any
•
broken glass or liquid from the damaged television. The LCD panel inside the TV contains glass and a toxic liquid. If the liquid comes in contact with your mouth or eyes, or your skin is cut by broken glass, rinse the affected area thoroughly with water and consult your doctor. ALWAYS contact a service technician to inspect the TV
•
any time it has been damaged or dropped.
15) CAUTION:
To reduce the risk of electric shock, do not
•
use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.
To prevent electric shock, match wide blade of plug
•
to wide slot; fully insert.
16) CAUTION: Do not let children swallow the product or play with the plastic bag. Keep the product and the plastic bag out of the reach of children.
17) CAUTION
18
) WARNING
:
Do not let water or other liquids come into contact with the product, as it may result in damage.
:
To prevent the spread of fire, keep candles or other
•
open flames away from this product at all times. Keep the product away from direct sunlight, fire or
•
a heat source such as a heater. This may reduce the product lifetime or result in fire.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and heed all warnings when installing your TV:
)
WARNING: NEVER expose batteries
19
to excessive heat such as sunshine, fire, or the like.
20
) ALWAYS plug the product into an outlet that is
located in such a manner that it can be easily unplugged in case the product requires service.
21
) NEVER route the product’s power cord inside a wall
or similar enclosed area.
22) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.
23
) DANGER: RISK OF SERIOUS PERSONAL
Never place the TV on an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.
INJURY, DEATH, OR EQUIPMENT DAMAGE!
(continued)
3
24
pot VTedis VT
) To avoid damage to this product, never place or store
the TV in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration.
25) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. To secure the TV, use a sturdy strap from the hook(s) on the rear of the TV to a wall stud, pillar, or other immovable structure. Make sure the strap is tight, secure, and parallel to the floor.
Sturdy strap (as short as possible)
4"
min.
Hook
33)
Use extreme care to make sure you are never in
•
DANGER: RISK OF SERIOUS
PERSONAL INJURY OR DEATH!
a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits. Never attempt to install any of the following
•
during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.
26) The apparatus should not be exposed to dripping or splashing. Objects filled with liquids should not be placed on the apparatus.
27) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:
on a bed, sofa, rug, or
•
similar surface; too close to drapes,
•
curtains, or walls; or in a confined space such
•
as a bookcase, built-in cabinet, or any other place with poor ventilation.
The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV. Leave a space of at least 4 (four) inches around the TV.
28) Always place the back of the television at least four (4) inches away from any vertical surface (such as a wall) to allow proper ventilation.
29) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.
30) Never overload wall outlets and extension cords.
31) Always operate this equipment from a 120 VAC, 60 Hz power source only.
32) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).
Antenna lead-in wire
Antenna discharge unit
Ground clamp
Electric service
equipment
Ground clamps
(NEC Section 810-20)
Grounding conductors (NEC Section 810-21)
Power service grounding electrode system (NEC Art 250 Part-H)
Care
For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:
34) If you use the TV in a room whose temperature is 32 °F (0 °C) or below, the picture brightness may vary until the LCD warms up. This is not a sign of malfunction.
35) Always unplug the TV before cleaning. Gently wipe the display panel surface (the TV screen) using a dry, soft cloth (cotton, flannel, etc.). A hard cloth may damage the surface of the panel. Avoid contact with alcohol, thinner, benzene, acidic or alkaline solvent cleaners, abrasive cleaners, or chemical cloths, which may damage the surface. Never spray volatile compounds such as insecticide on the cabinet. Such products may damage or discolor the cabinet.
36)
Never spill liquids or push objects of any kind into the TV cabinet slots.
37) While it is thundering, do not touch the connecting cables or apparatus.
38) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.
39) ALWAYS unplug the TV to completely disconnect from mains power. When the TV is turned off using the on/off switch, it is not completely disconnected from power and a minute amount of current is still consumed.
WARNING:
RISK OF ELECTRIC SHOCK!
4
40)
During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Provider.
41)
Never strike the screen with a sharp or heavy object.
42) •TheLCDscreenofthisproductcanbedamagedby
•
DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH!
ultraviolet radiation from the sun. When selecting a location for the television, avoid locations where the screen may be exposed to direct sunlight, such as in front of a window.
Never touch, press, or place anything on the LCD screen. These actions will damage the LCD screen. If you need to clean the LCD screen, follow the instructions in item 35 on page 4.
Service
43)
Never attempt to service the TV yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Provider.
44) If you have the TV serviced: Ask the service technician to use only replacement
•
parts specified by the manufacturer. Upon completion of service, ask the service technician
•
to perform routine safety checks to determine that the TV is in safe operating condition.
45)
The cold cathode fluorescent lamp in the LCD panel contains a small amount of mercury.
When the TV reaches the end of its useful life, dispose of the used TV by the approved method for your area, or ask a qualified service technician to properly dispose of the TV.
environmental considerations. For disposal or recycling information, contact your local authorities or the Electronics Industries Alliance (www.eiae.org).
WARNING:
RISK OF ELECTRIC SHOCK!
Note: The lamp(s) inside this product contain mercury. Disposal may be regulated due to
Choosing a location for your LCD TV
To Display your LCD TV on the included Pedestal Stand:
Observe the following safety precautions:
1) Read and Follow the pedestal assembly instructions
included with the pedestal. CAUTION: Before beginning pedestal assembly, carefully lay the front of the LCD Panel face down on a flat, cushioned surface such as a quilt or blanket. Leave the bottom of the unit protruding over the edge of the surface and assemble the pedestal as indicated below.
Note: Extreme care should always be used when attaching the pedestal stand to avoid damage to the LCD panel.
2) Place the TV on a sturdy, level surface that can
support the weight of the TV.
3) Be sure to secure the TV to a wall, pillar, surface, or
other immovable structure (item 25, page 4).
To Display your LCD TV using a Wall Bracket:
If you decide to wall mount your LCD TV, always use a UL listed wall bracket appropriate for the size and weight of the LCD TV ( page 2):
1) CAUTION:
2) Unplug and remove any cables and/or other component connectors from the rear of the TV.
3) Remove the screws of the VESA Mounting Pattern show in the next page.
CAUTION:
the back cover to attach the wall mount bracket to the TV.
4) Always use the screws supplied or recommended by the wall mount manufacturer.
5) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.
6) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand from the TV as described on page 6.
7) VESA Mounting Pattern
Two people are required for installation.
Do not use the screws removed from
5
TV Size Hole Pattern(HxV) Screw Size
32” 200x200 mm M6 40” 200x200 mm M6
(unit in mm)
Removing the Pedestal Stand
Carefully lay the front of the unit face down on a
1) flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface.
Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.
2) Remove the four screws shown in the below diagram. This will allow removal of the pedestal stand.
3) Once you have removed all four screws holding the pedestal stand in place, remove the pedestal stand from the TV.
32/40” TV
VESA Mounting Pattern
Four screws
Hook Sturdy strap
(as short as possible)
CAUTION: Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. To secure the TV, use a sturdy strap from the hook(s) on the rear of the TV to a wall stud, pillar, or other immovable structure. Make sure the strap is tight, secure, and parallel to the floor.
6
FCC Declaration of Conformity Compliance Statement (Part 15):
Important notes about your LCD TV
Toshiba 32DT2U, 32DT2UL and 40FT2U Television models comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
The party responsible for compliance to these rules is: Toshiba America Information Systems, Inc. 9740 Irvine Blvd.; Irvine CA 92618 Ph: 1-800-631-3811
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
•
the receiver. Connect the equipment into an outlet on a circuit
•
different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV
•
technician for help.
Caution: Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment.
The following symptoms are technical limitations of LCD Display technology and are not an indication of malfunction; therefore, Toshiba is not responsible for perceived issues resulting from these symptoms.
1) An afterimage (ghost) may appear on the screen if a fixed, nonmoving image is displayed for a long period of time. The afterimage is not permanent and will disappear in a short period of time.
2) The LCD panel contained in this TV is manufactured using an extremely high level of precision technology; however, there may be an occasional pixel (dot of light) that does not operate properly (does not light, remains constantly lit, etc.). This is a structural property of LCD technology, is not a sign of malfunction, and is not covered under your warranty. Such pixels are not visible when the picture is viewed from a normal viewing distance.
Note: Interactive video games that involve shooting a “gun” type of joystick at an on­screen target may not work with this TV.
Trademark Information
ManufacturedunderlicensefromDolby
•
Laboratories. Dolbyandthedouble-Dsymbolaretrademarks ofDolbyLaboratories.
HDMI,theHDMIlogo,andHigh-Definition
•
MultimediaInterfacearetrademarksor registeredtrademarksofHDMILicensingLLC theUnitedStatesandothercountries.
ThisproductioncontainsBitstreamVeraSans
•
fontsunderthefollowingcopyright. Copyright©2003byBitstream,Inc.AllRights Reserved. BitstreamVeraisatrademarkofBitstream,Inc.
in
7
Contents
Important Safety Instructions ............................ 3
Installation, Care, and Service .......................... 3
Chapter 1: Introduction ................................... 9
Features of your new TV ......................................................9
Overview of steps for installing, setting up,
and using your new TV ...............................................10
TV front and side panel controls and connections............. 11
TV back panel connections ................................................ 12
Chapter 2: Connecting your TV .........................13
Overview of cable types ..................................................... 13
About the connection illustrations .....................................13
Connecting a VCR, Antenna, Cable TV, or Camcorder ....14
Connecting a DVD player with ColorStream
(component video), a VCR, and a satellite receiver ... 15 Connecting an HDMI REGZA-LINK
®
or DVI device to the HDMI input 16
®
connection ...............................................17
Connecting a digital audio system ..................................... 18
Connecting a personal computer (PC) ...............................18
Chapter 3: Using the remote control ................... 20
Installing the remote control batteries ................................ 20
Remote control effective range .......................................... 20
Learning about the remote control ..................................... 21
Chapter 4: Menu layout and navigation ...............22
Main menu layout ............................................................... 22
Setup/Installation menu layout ...........................................23
Navigating the menu system .............................................. 23
Chapter 5: Setting up your TV ...........................24
Initial Setup .........................................................................24
Selecting the menu language ..............................................24
Configuring the antenna input source for the
ANT/CABLE terminal ................................................24
Programming channels into the TV’s channel memory .... 25
Programming channels automatically ............................ 25
Setting channel skip ........................................................25
Setting AV Input mode .......................................................26
Setting the HDMI
Viewing the digital signal meter.........................................27
®
audio mode .........................................26
Setting the time zone ..........................................................27
Viewing the system status ..................................................27
Chapter 6: Using the TV’s features .....................28
Selecting the video input source to view ........................... 28
Labeling the video input sources........................................ 28
Tuning channels ..................................................................29
Tuning channels using the Channel Browser™ ............. 29
Setting the Channel Tuning Mode ..................................31
Tuning to the next programmed channel ........................ 31
Tuning to a specific channel
(programmed or unprogrammed) ......................... 31
Switching between two channels using SurfLock™ ..... 32
Selecting the picture size ....................................................32
Scrolling the TheaterWide
(TheaterWide 2 and 3 only).........................................34
®
picture
Using the auto aspect ratio feature ..................................... 34
Using the FREEZE feature................................................. 34
Adjusting the picture .......................................................... 34
Selecting the picture mode .............................................. 34
Adjusting the picture quality .......................................... 35
Using the closed caption mode ..........................................35
Base closed captions .......................................................35
Digital CC Settings ........................................................36
CC Selector .....................................................................36
®
Adjusting the audio ............................................................37
Muting the sound ............................................................ 37
Using the digital audio selector ......................................37
Selecting stereo/SAP broadcasts ....................................37
Adjusting the audio quality ............................................. 37
Selecting the digital audio output format .......................38
Using the Dolby
®
Digital Dynamic Range
Control feature ......................................................38
Using the Locks menu ........................................................38
Entering the PIN code ..................................................... 38
If you cannot remember your PIN code ......................... 38
Changing your PIN code ................................................ 39
Blocking TV programs and movies
by rating (V-Chip) ................................................39
Downloading an additional rating system
for blocking TV programs and movies ................ 39
Unlocking programs temporarily ...................................41
Using the input lock feature ............................................ 41
Locking channels ............................................................41
Using the GameTimer
Using the panel lock feature ...........................................42
®
...................................................41
Using the PC settings feature .............................................42
Setting the PC Audio ..........................................................43
Using the Media Player ......................................................43
Using the Media Player with USB .................................43
To select the Auto Start function ....................................43
To open the Media Player ..............................................44
Viewing photo files ........................................................44
Single View .....................................................................44
Slideshow ........................................................................44
Setting the sleep timer ........................................................45
Automatic Power Down .....................................................46
No Signal Power Down ......................................................46
Using REGZA-LINK
REGZA-LINK
(DVD player, etc.) control ...................................46
REGZA-LINK
VOLUME and MUTE controls of Audio Receiver ....... 47
Other REGZA-LINK
Displaying TV status information ......................................48
®
....................................................... 46
®
playback device
®
input source selection ..........................47
®
functions .................................... 47
Understanding the last mode memory feature ...................48
Chapter 7: Using the TV’s advanced features ........49
Using the advanced picture settings features ..................... 49
Using Dynamic Contrast.................................................49
Using the static gamma feature ......................................49
Selecting the color temperature ......................................49
Using CableClear
Using MPEG noise reduction .........................................50
®
digital noise reduction ..................... 50
Using the Game Mode feature ........................................50
Chapter 8: Troubleshooting .............................51
General troubleshooting ..................................................... 51
Chapter 9: Appendix ......................................53
Specifications ......................................................................53
Acceptable signal formats for PC IN
and HDMI terminals .................................................... 54
Limited United States Warranty for LCD Televisions ....... 55
Limited Canadian Warranty for
Toshiba Brand Flat Panel Televisions ......................... 56
8
Chapter 1: Introduction
Features of your new TV
The following are just a few of the many exciting features of your new Toshiba widescreen, integrated
HD, LCD TV:
Integrated digital tuning (8VSB ATSC and
•
QAM) eliminates the need for a separate digital converter set-top box (in most cases). 1366 x 768 output resolution
•
(32DT2U / 32DT2UL). 1920 x 1080 output resoluation (40FT2U).
HDMI® digital, high-definition multimedia
•
interfaces 1080p input support (page 16).
One set of ColorStream® HD high-resolution
•
component video inputs (page 15). This is used by setting the AV input mode to ColorStream® HD (page 26).
Digital Audio Out digital audio connection with
•
®
Digital audio output format (page 38).
Dolby
CableClear® digital picture noise reduction (
•
page 50).
PC IN (Analog RGB) computer terminal (
•
pages 18-19).
REGZA-LINK® allows control of external
•
devices from the TV remote via HDMI connection (page 46).
Media Player allows you to view your JPEG files
•
(page 43).
9
Overview of steps for installing, setting up, and using your new TV
Follow these steps to set up your TV and begin using its many exciting features.
Carefully read the important safety, installation,
1
care, and service information. Keep this manual for future reference.
Observe the following when choosing a location
2
for the TV:
Read “Important notes about your LCD TV”
•
(page 7). Place the TV on the floor or a sturdy, level,
•
stable surface that can support the weight of the unit. Secure the TV to a wall, pillar, or other immovable structure ( page 4). Place the TV in a location where light does not
•
reflect on the screen. Place the TV far enough from walls and other
•
objects to allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY.
Do not plug in any power cords until AFTER you
3
have connected all cables and devices to your TV.
4
BEFORE connecting cables or devices to the TV, learn the functions of the TV’s connections and
controls (pages 11–12).
5
Connect your other electronic device(s) to the TV (pages 13–19).
6
Install the batteries in the remote control (page
20).
7
See “Learning about the remote control” (page
21) for an overview of the buttons on the remote control.
8
AFTER connecting all cables and devices, plug in the power cords for your TV and other devices.
Then press POWER on the TV control panel or remote control to turn on the TV. If the TV stops responding to the remote control or TV control panel and you cannot turn the TV off or on, please unplug the power cord a few seconds then plug it back in and try again.
9
See “Menu layout and navigation” for a quick overview of navigating the TV’s menu system
(page 22).
10 Program channels into the TV’s channel memory
(page 24).
11 For details on using the TV’s features, see
Chapters 6 and 7.
12 For help, refer to Chapter 8: Troubleshooting. 13 For technical specifications and warranty
information, see Chapter 9.
14 Enjoy your new TV!
10
Chapter 1: Introduction
12
3
7
8
9
4
5
6
10
TV front and side panel controls and connections
Models 32DT2U, 32DT2UL, and 40FT2U are used in this manual for illustration purposes.
Left side panel
1無 Green LED
Power LED (Green) = Power indicator
2無 Remote sensor (embedded)
control toward this remote sensor ( “Remote control effective range” on page 20).
— Press to turn the TV on and off. If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the TV, press and hold the
button on the TV control panel for 5 or
POWER
more seconds to reset the TV.
screen, these buttons function as up/down/left/ right menu navigation buttons.
system ( pages 22–23). When a menu is on­screen, the panel can function as the
— Press to instantly close an on-screen
menu.
3無 POWER
4無 ARROWS
5無 MENU (ENTER)
6無 EXIT
— Point the remote
— When a menu is on-
pqtu
— Press to access the menu
button on the TV’s control
MENU
ENTER
button.
TV front
TV top
7無 CHANNEL
these buttons change the channel (programmed channels only;  page 25).
8無 VOLUME
These buttons adjust the volume level.
9無 INPUT
source you are viewing.
10無 USB port
pq — When no menu is on-screen,
tu — When no menu is on-screen.
— Repeatedly press to change the video
— To access JPEG files.
11
Chapter 1: Introduction
TV back panel connections
For an explanation of cable types and connections, see pages 13–19.
TV back
Power Cord
1無 PC IN
2無 HDMI
3無 PC/HDMI 1 (AUDIO) IN
4無 ANT/CABLE
5無 DIGITAL AUDIO OUT
— For use when connecting a personal
computer.
®
— High-Definition Multimedia
IN
Interface input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. HDMI connection is necessary to receive 1080p signals.
terminal is shared with HDMI 1 analog audio input terminals, and its use can be configured in the
Audio Setup
and digital (ATSC) off-air antenna signals and analog and digital Cable TV (QAM) signals.
Dolby Digital or PCM (Pulse-Code Modulation) format for connecting an external Dolby Digital decoder, amplifier, or home theater system with digital audio input.
— Input that supports analog (NTSC)
— PC audio input
menu ( page 43).
audio output in
Digital
1
56
6無 VIDEO / COLORSTREAM® HD IN
include standard A/V connections ( page 15). These are switched by AV input mode ( page 26).
Note: Component / Standard (composite) video cables carry only video information; separate audio cables are required for a complete connection.
— These
2
3 4
12
Chapter 2: Connecting your TV
Overview of cable types
Cables can be purchased from most stores that sell audio/ video devices. Before purchasing any cables, be sure of connector types required by your devices and the length of each cable.
Coaxial cable (F-type)
(F-type) Coaxial cable is used for connecting your antenna, cable TV service, and/or cable converter box to the ANT/CABLE input on your TV.
Standard A/V cables (red/white/yellow)
Standard A/V cables (composite video) usually come in sets of three, and are for use with video devices with analog audio and composite video output. These cables (and the related inputs on your TV) are typically color­coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio.
Component video cables (red/green/blue)
Component video cables come in sets of three and are for use with video devices with component video output. (ColorStream® is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection.
Note: Component video cables provide better picture performance than a standard (composite) video.
Coaxial digital audio cable
Coaxial digital audio cable is for connecting receivers with Dolby Digital or PCM (pulse-code modulation) digital audio input to the TV’s DIGITAL AUDIO OUT terminal (page 18).
Analog RGB (15-pin) computer cable
Analog RGB (15-pin) computer cable is for connecting a PC to the TV’s PC IN terminal (page 18).
Note: Separate audio cables are required for a complete connection.
3.5mm Stereo to RCA Y-cable
3.5mm Stereo to RCA Y-Cable is for connecting audio signals from a DVI device to the TV.
About the connection illustrations
You can connect different types and brands of devices to your TV in several different configurations. The connection illustrations in this manual are representative of typical device connections only. The input/output terminals on your devices may differ from those illustrated herein. For details on connecting and using your specific devices, refer to each device’s owner’s manual.
HDMI® cable (with HDMI Logo “ ”)
HDMI (High-Definition Multimedia Interface) cable is for use with devices with an HDMI output. An HDMI cable delivers digital audio and video in its native format. This cable carries both video and audio information; therefore, separate audio cables are not required for a complete HDMI device connection ( page 16 and page 19).
Note: HDMI cable provides better picture performance than a standard (composite) video.
13
Chapter 2: Connecting your TV
IN
OUT
CH 3 CH 4
IN from ANT
VIDEO AUDIO
OUT
to
TV
L R
R
L
OUT
IN
CH 3 CH 4
VIDEO
AUDIO
OUT
L
R
Connecting a VCR, Antenna, Cable TV, or Camcorder
Camcorder
TV back panel
Standard audio cable
You will need:
Coaxialcables
•
StandardA/Vcables
•
− If you have a mono VCR, connect on the TV to your VCR’s audio out terminal using the white audio cable only.
Standardaudiocables.
•
Note:
When you use a Cable box, you may not be
•
able to use the remote control to program or access certain features on the TV. When you use ColorStream HD or Video,
•
switch AV input mode appropriately (“Setting AV Input mode” on page 26).
To view the antenna or Cable signal:
SelecttheANT/CABLEvideoinputsourceontheTV.*
To view basic and premium Cable channels:
TurnOFFtheVCR.SelecttheANT/CABLEvideo
L/MONO
From Cable TV or
From Cable TV
antenna
Stereo VCR
Standard A/V cables
Coaxial cable
inputsourceontheTV.*TunetheTVtochannel3or 4(whicheverchanneltheCableboxoutputissetto). UsetheCableboxcontrolstochangechannels.
To view the VCR:
TurnONtheVCR.SelecttheVIDEO videoinput sourceontheTV.*
To view the camcorder video:
SelecttheVIDEO videoinputsourceontheTV.*
To select the video input source, press
*
remote control ( page 21).
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.
Cable box
on the
14
Chapter 2: Connecting your TV
S-VIDEO
OUT
VIDEO
OUT
AUDIO
OUT
COMPONENT VIDEO
L
R
Satellite
IN
P
B
P
R
Y
IN from ANT
VIDEO AUDIO
OUT to TV
L R
R
L
OUT
IN
CH 3 CH 4
Connecting a DVD player with ColorStream® (component video), a VCR, and a satellite receiver
From satellite dish
Standard audio cable
Component video cable
Satellite receiver with component video or DVD player with component video
You will need:
Coaxialcables
•
StandardA/Vcables
•
− If you have a mono VCR, connect on the TV to your VCR’s audio out terminal using the white audio cable only.
Standardaudiocables
•
Componentvideocables
•
− You can connect the component video cables (plus audio cables) from the DVD player or satellite receiver to the on the TV. The can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems. A 1080i signal will provide the best picture performance (1080p is not supported).
− If your DVD player or satellite receiver does not have component video, connect a standard A/V cable to your DVD player has HDMI video, see page
16.
Note: When you use ColorStream HD or Video, switch AV input mode appropriately ( AV Input mode” on page 26).
ColorStream
ColorStream HD
VIDEO
TV back panel
L/MONO
terminal
terminal
terminal. If
“Setting
Stereo VCR
Coaxial cable
Standard A/V cables
To view antenna or Cable channels:
SelecttheANT/CABLEvideoinputsourceontheTV.*
To view the DVD player:
TurnONtheDVDplayer.SelecttheColorStream HD videoinputsourceontheTV.*
To view satellite programs using the component video connections:
Turnonthesatellitereceiver.SelecttheColorStream
HD
videoinputsourceontheTV.*
To view the VCR or view and record antenna channels:
TurnONtheVCR.TunetheVCRtothechannelyouwant towatch.SelecttheVIDEO videoinputsourceontheTV.*
To select the video input source, press
*
remote control (page 21).
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.
From antenna
on the
15
Chapter 2: Connecting your TV
Connecting an HDMI® or DVI device to the HDMI input
The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device. This input is designed to accept HDCP (High­Bandwidth Digital-Content Protection) program material in digital form from EIA/CEA-861-D­compliant a set-top box or DVD player with HDMI or DVI output).The HDMI input can accept and display VGA, SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz) and 1080p (24Hz/60Hz) signal formats. For detailed signal specifications, see page 56. Supported Audio format: Linear PCM, sampling rate 32/44.1/ 48 kHz
Note: To connect a PC to the HDMI input, see page 19.
To connect an HDMI device, you will need:
•
To view the HDMI device video:
Select the HDMI 1, HDMI 2 video input source on the TV.
[1]
consumer electronic devices (such as
One HDMI cable (type A connector) per HDMI device
− For proper operation, it is recommended that you use an HDMI cable with the HDMI Logo ( ).
− To display a 1080p/60Hz signal format, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work properly.
− HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration).
− See “Setting the HDMI ® audio mode” ( page 26).
TV back panel
HDMI device
HDMI cable
*
To select the video input source, press
*
remote control (page 21).
on the
To connect a DVI device, you will need:
One HDMI-to-DVI adapter cable
•
− For proper operation, the length of an HDMI­to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).
One 3.5mm stereo to RCA Y-cable
•
− An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration).
− See “Setting the HDMI ® audio mode” ( page 26).
TV back panel
Audio cable
DVI device
VIDEO AUDIO
L R
IN
IN
OUT
R
L
Note: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:
When turning on your electronic components,
turn on the TV first, and then the HDMI or
DVI device.
When turning off your electronic components,
turn off the HDMI or DVI device first, and
then the TV.
[1] EIA/CEA-861-D compliance covers the
transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.
DVI/HDCP
OUT
HDMI-to-DVI adapter cable
16
Chapter 2: Connecting your TV
REGZA-LINK® connection
You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a REGZA-LINK® compatible audio receiver or playback device. For an explanation of setup and operations, see page 46.
TV back panel
Audio receiver
Playback device (REGZA-LINK
®
DVD player, etc.)
To connect an Audio Receiver and Playback Devices, you will need:
HDMI cables ( page 13)
•
Note:
If several devices are connected, the
REGZA-LINK feature may not operate
properly.
For proper operation, it is recommended that
you use HDMI cables with the HDMI Logo
( ).
Playback device (REGZA-LINK
®
DVD player, etc.)
Before controlling the device(s):
After completing the above connections, set the
•
REGZA-LINK Setup
47). The connected devices must also be set. For
•
details, see the operation manual for each device. The REGZA-LINK® feature uses the CEC
•
technology as regulated by the HDMI standard. This feature is limited to models incorporating
•
Toshiba’s REGZA-LINK liable for those operations. Refer to the individual instruction manuals for compatibility information.
Note: This feature may not work properly depending on the devices that are connected.
menu as you desire ( page
®
. However, Toshiba is not
17
Chapter 2: Connecting your TV
Connecting a digital audio system
The TV’s DIGITAL AUDIO OUT terminal outputs a
® *
Dolby
Digital or 2-channel down-mixed PCM (Pulse-Code Modulation) signal for use with an external Dolby® Digital decoder or other external audio system with digital audio input.
You will need:
Coaxial digital audio cable
•
Dolby Digital decoder or
other digital audio system
DIGITAL
AUDIO IN
TV back panel
To control the audio:
Turn on the TV and the digital audio device.
1無
Press on the TV’s remote control and open the
2無
Sound menu.
Highlight Audio Setup and press .
3無
Coaxial digital audio cable
Note:
Some audio systems may not be compatible
with Dolby Digital bitstream signals. Older audio systems that are not compatible with standard digital out signals may not work properly, creating a high noise level that may damage speakers or headphones. THIS DAMAGE IS NOT COVERED BY YOUR WARRANTY.
The DIGITAL AUDIO OUT terminal may not
output some digital audio sources because
of copy restrictions.
Manufactured under license from Dolby
*
Laboratories. Dolby, and the double-D symbol are trademarks of Dolby Laboratories.
Connecting a personal computer (PC)
With either the PC IN or HDMI connection, you can watch your computer’s display on the TV and hear the sound from the TV’s speakers.
To connect a PC to the PC IN terminal on the TV:
When connecting a PC to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable.
TV back panel
Analog RGB computer cable
PC audio
cable
In the
4無
Dolby Digital
Digital Output Format
or
PCM
field, select either
, depending on your device
(“Selecting the digital audio output format” on page 38).
18
Computer
PC audio
output
Conversion adapter (if necessary)
To use a PC, set the monitor output resolution on the
•
PC before connecting it to the TV. The PC IN terminal can accept and display VGA, SVGA, XGA, WXGA and SXGA signal formats. For detailed signal specifications ( page 56). Other formats or non-standard signals will not be displayed correctly. To display the optimum picture, use the PC setting
•
feature ( “Using the PC settings feature” on page 42).
(continued)
Loading...
+ 41 hidden pages