Toshiba 15DLV76 Schematic

FILE NO. 810-200621GR

SERVICE MANUAL

15-inch Diagonal LCD TV/DVD COMBINATION

15DLV76

The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).

For (*1) and (*2), see the next page.

DOCUMENT CREATED IN JAPAN, April, 2006 GREEN

(*1) GREEN PRODUCT PROCUREMENT

The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances.

Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.

Green procurement of parts is not only confined to manufacture. The same green parts used in manufacture must also be used as replacement parts.

(*2) LEAD-FREE SOLDER

This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product.

WARNING

This product is manufactured using lead free solder .

DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !

The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F (30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product made with lead-free solder may result in damage to the component and or PCB being soldered. Great care should be made to ensure high-quality soldering when servicing this product ⎯ especially when soldering large components, through-hole pins, and on PCBs ⎯ as the level of heat required to melt lead-free solder is high.

ColorStream® is a registered trademark of Toshiba America Consumer Products, L.L.C.

is a trademark of Toshiba America Consumer Products, L.L.C.

J5X00201A SH 06/02

Printed in Thailand

15-inch Diagonal LCD TV/DVD

COMBINATION

15DLV76

OWNER’S MANUAL

Introduction

Connections

Basic setup

TV operation

Basic playback

Advanced playback

Function setup

Others

Introduction

The lightning flash with arrowhead symbol, within an equilateral

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN CAUTION : TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

FCC NOTICE :

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with

WARNING: Handling the cord on this product or cords associated with accessories sold with this product will

CAUTION:

THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE

READ THIS OWNER'S MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM.

OR MOISTURE.

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

the FCC (Federal Communications Commission) Rules could void the user's authority to operate this equipment.

expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a soft dry cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation, and to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

11. GROUNDING OR POLARIZATION

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

PORTABLE CART WARNING

(symbol provided by RETAC)

S3125A

the plug

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. However, if there is thunder or lightning now, do not touch the unit and any connected cable. This will for you not to receive the electric shock by the serge of thunder.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

NEC-NATIONAL ELECTRICAL CODE S2898A

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. For example: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the

unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING

ELECTRODE SYSTEM (NEC ART 250, PART H)

(continued)

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

22. DISC SLOT

Keep your fingers well clear of the disc slot as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

24. HEADPHONES

When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

25. LASER BEAM

Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

26. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

27. LCD

Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur. Should the LCD panel be broken and liquid leaks out, do not inhale or swallow it. Doing so may cause poisoning. If you have got it into your mouth, wash it out and consult your doctor. If your hands or clothes have touched it, wipe them with alcohol and a cleaning cloth and then wash them well.

28. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

ON DISPOSAL

This product contains mercury. Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industrial Alliance : www.eiae.org.

Introduction

Precautions

Notes on handling

■ Do not shock the LCD panel. It may cause unit damage and malfunction.

■ When shipping the unit, the original shipping carton and packing materials come in handy. For fully protection, repack the unit as it was originally packed at the factory.

■ Do not use volatile liquids, such as insect spray, near the unit. Do not leave rubber or plastic products to contact the unit for prolonged period. They will leave marks on the finish.

■ The top and rear panels of the unit may become warm after a long period of use. This is not a malfunction.

■ When the unit is not in use, be sure to remove the disc and turn off the power.

■ If you do not use the unit for a long period, the unit may not function properly in the future. Turn on and use the unit occasionally.

Notes on LCD

The color LCD is manufactured using extremely high precision technology, but even so may include certain pixels that do not operate properly (that do not light, that remain lit constantly, etc.). We do our best to keep the number of these defective pixels to a minimum, but please understand that they cannot be completely eliminated even with the most advanced manufacturing technologies available today. The fluorescent tube which illuminates the panel from the inside will deteriorate with use. When the LCD becomes dim, flickers, or does not illuminate, contact your dealer for replacement. The brightness of the LCD monitor differs slightly depending on the viewing angles. Adjust the angle to obtain the best viewing. (The recommended angle is 90 degrees to the monitor.)

Notes on locating

■ When you place this unit near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted. In this case, place the unit away from the TV, radio, or VCR.

■ To avoid damage to this product, never place or store the unit in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration.

■ Always place the

TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. Use a sturdy tie between the TV’s rear hook and the rear wall, pillar, etc., to secure the TV. If you use a TV stand, fix the TV by using the attached

band.

Sturdy tie (as short as possible)

Hooks

Band

TV side

TV top

Notes on moisture condensation

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

■ Moisture condensation occurs during the following cases.

When you bring the unit directly from a cold place to a warm place. When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit. In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room. When you use the unit in a humid place.

■ Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

Clip

Screw

Wait!

Notes on cleaning

Use a soft, dry cloth for cleaning.

Do not use any type of solvent, such as thinner and

benzine, as they may damage the surface of the unit.

Optical pick-up

lens

Wall outlet

Notes on discs

On handling discs

Do not touch the playback side of the disc. For example, handle the disc so that it is shown in figure below.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources. Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Video CDs and Audio CDs are divided into tracks.

DVD video disc

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively. There may be discs that do not have these numbers.

DVD video disc

Title 1 Title 2

Video CD/Audio CD

Notes on copyright

The unauthorized recording, use, distribution, or revision of copyrighted materials including, without limitation, television programs, videotapes, and DVDs, is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Introduction

Notes on discs (Continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this unit. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the unit may not respond to all operating command. This is not a defect in the unit. Refer to instruction notes of discs.

The following symbol may appear on the TV screen during operation.

It means that the operation is not permitted by the TV/ DVD or the disc. For example, sometimes it is unable to stop the playback of copyright message of the disc when the

) button is pressed. Alternatively, this symbol

STOP ( may also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this unit is 1. If region numbers, which stand for their playable area, are printed on your DVD video disc and you do not find playback will not be allowed by the player. (In this case, the unit will display a message on-screen.) Some DVDs that have no region code label may still be subject to area restrictions and therefore not playable.

On Video CDs

This DVD supports Video CDs equipped with the PBC (Version 2.0) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on types of discs.

• Video CD not equipped with PBC function (Version 1.1)

Sound and movie can be played on this DVD in the same way as an audio CD.

• Video CD equipped with PBC function (Version 2.0)

In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback). Some of the functions described in this owner’s manual may not work with some discs.

ALL

, disc

Playable discs

This unit can play the following discs.

Contents

Disc Mark

DIGITAL VIDEO

format

Audio

Video (moving pictures)

Audio

Video (moving

pictures)

Audio

DVD video discs

Video CDs

Audio CDs

The following discs are also available.

DVD-R/RW discs of DVD video format CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA, JPEG or DivX Kodak Picture CD and FUJICOLOR CD format

Some of these discs may be incompatible.

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM, Photo

CD, etc., or non standardized discs even if they may be labeled as above.

• Some CD-R/RWs cannot be played back depending on the recording conditions.

• This unit uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).

• This unit can play an 8cm disc. Please do not use a disc adapter. It may cause trouble.

• Please do not insert any disc of an irregular shape into the unit, as it may interfere with the function of the unit. You may not be able to remove it.

• Please do not use after market accessories, such as a ring protector, as this may cause trouble with the operation of the unit.

Because of problems and errors that can occur during the creation of DVD and CD Software and/or the manufacture of DVD and CD discs, Toshiba cannot assure that the DVD player contained in this TV will successfully play every disc bearing the DVD and CD logos. If you happen to experience any difficulty playing a DVD and/or CD disc on the DVD player contained in this TV, please contact Toshiba Customer Service.

is a trademark of DVD Format/Logo Licensing Corporation.

Maximum

Disc

playback time

Size

Approx. 4 hours

(single sided disc)

12 cm

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

8 cm

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

12 cm

(single sided disc)

Approx. 20 minutes

8 cm

(single sided disc)

Approx. 74 minutes

12 cm

(single sided disc)

Approx. 20 minutes

8 cm

(single sided disc)

Contents

Introduction

IMPORTANT SAFEGUARDS............................3

Precautions ....................................................... 6

Notes on discs................................................... 7

Contents............................................................9

Identification of controls ..................................10

Connections

Antenna connections....................................... 14

Cable TV connections ..................................... 15

Connecting to optional equipment................... 16

Power source .................................................. 20

Basic setup

Setting the language ....................................... 21

To memorize channels....................................22

TV operation

TV operation.................................................... 23

Closed captions............................................... 25

Setting the V-Chip ........................................... 26

Picture control adjustment............................... 28

Adjusting the picture mode.............................. 28

Selecting the color temperature ...................... 29

Sound control adjustment ...............................30

Stereo and Second Audio Program (SAP)......30

Basic playback

Playing a disc .................................................. 31

Advanced playback

Zooming ......................................................... 34

Locating desired scene .................................. 34

Repeat playback ............................................ 35

A-B Repeat playback ..................................... 35

Program playback .......................................... 36

Random playback .......................................... 36

Changing angles ............................................ 37

Title selection ................................................. 37

DVD menu...................................................... 37

Changing soundtrack language ..................... 38

Subtitles ......................................................... 38

Disc status...................................................... 39

To turn off the PBC ........................................ 39

MP3/WMA/JPEG/DivX

and Audio CD operation................................. 40

Repeat and program playback

using file browser ........................................... 44

Function setup

Customizing the function settings .................. 46

Temporary cancel the rating level

by DVD disc ................................................... 52

Others

Language code list ......................................... 53

Troubleshooting ............................................. 54

Reception disturbances.................................. 56

Specifications ................................................. 57

Limited United States Warranty ..................... 58

Introduction

Identification of controls

See the page in for details.

Top

POWER button

VOLUME ( ) buttons

CHANNEL (4/3) buttons

EJECT ( ) button

SKIP ( / ) buttons

STOP( ) button

PLAY ( ) button

Front

Speaker Speaker

Side

Adjusting the angle of the base

Approx. 15° Approx. 5°

Introduction

Left Side Right Side

PHONES jack

AUDIO IN (L/R)

/VIDEO IN

(LINE 2 IN) jacks

S-VIDEO jack

Disc slot

You can adjust the angle of the TV-screen for 5° forward or for 15° backward from vertical angle. Hold the base of the TV while adjusting the angle.

Rear

COAXIAL DIGITAL AUDIO OUT jack

Remote sensor

POWER indicator

Antenna jack

DC input jack

VIDEO IN (LINE 1 IN) jack

COMPONENT VIDEO IN (Y, P

B, PR) (LINE 1 IN) jacks

AUDIO IN (L/R) (LINE 1 IN) jacks

Introduction

Identification of controls (Continued)

Remote control

The instructions in this manual describe the function on the remote control. See the page in for details.

EJECT button

TV/DVD button

Direct channel selection

buttons (0

Numbered buttons (0

TOP MENU button

*DVD MENU button

Use the DVD MENU button to display the menu included on many DVD video discs. To operate a menu, follow the instructions in “DVD menu.”

RECALL button

JUMP button

INPUT SELECT button

PLAY MODE button

GAME button

MENU button

SETUP button

PLAY button STOP button SKIP buttons

REV button

FWD button

SLOW buttons

ANGLE button AUDIO button

37 42

34 16 35 16

21 46

31 31 33 33 33 33

37 38

POWER button SLEEP button

CH RTN button ZOOM button

MUTE button VOL +/– buttons CANCEL button

*DVD MENU button

Direction buttons CH +/– buttons

ENTER button RETURN button

PAUSE button

CLOSED CAPTION button REPEAT A-B button

SUBTITLE button

21 34

( / / / )

37 42

Inserting batteries

Open the battery compartment

cover in the direction of the arrow.

Install two “R03/AAA” batteries

(supplied), paying attention to the polarity indicated in the battery compartment.

Replace the compartment cover.

Introduction

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5 meters.

Approx. 5 meters

Caution:

• Never throw batteries into a fire.

Notes:

Be sure to use AAA size batteries.

•

• Dispose of batteries in a designated disposal area. Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with

• applicable laws and regulations.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.

• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Connections

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see page 15 for Cable TV connections.

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Antenna

jack

75 ohm coaxial cable (not supplied)

Antenna

jack

300-75 ohm matching transformer (supplied)

Connect the 75 ohm cable from the combination VHF/UHF antenna to the antenna jack on the back of the TV/DVD.

If your combination VHF/UHF antenna has a 300 ohm twin-lead wire, use the 300-75 ohm matching transformer.

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

Antenna

jack

Combiner (not supplied)

UHF 300 ohm twin-lead wire (not supplied)

300-75 ohm matching transformer (supplied)

VHF 300 ohm twin-lead wire (not supplied)

Connect the UHF 300 ohm twin-lead wire to the combiner (not supplied). Connect the VHF 300 ohm twin-lead wire to the 300-75 ohm matching transformer. Attach the transformer to the combiner, then attach the combiner to the antenna jack on the back of the TV/DVD.

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

Antenna

jack

Combiner (not supplied)

UHF 300 ohm twin-lead wire (not supplied)

VHF 75 ohm (not supplied)

Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the combiner (not supplied). Attach the combiner to the antenna jack on the back of the TV/DVD.

Cable TV connections

This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

For subscribers to basic cable TV service

75 ohm coaxial cable

Antenna

jack

For basic cable service not requiring a converter/descrambler box, connect the Cable TV 75 ohm coaxial cable directly to the Antenna jack on the back of the TV/DVD.

For subscribers to scrambled cable TV service

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to select channels.

Incoming 75 ohm Cable TV

For subscribers to unscrambled basic cable TV service with scrambled premium channels

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A” position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/ descrambler box to tune scrambled channels.

Incoming 75 ohm Cable TV

Splitter

Converter/

descrambler

Converter/

descrambler

A/B switch

75 ohm cable to TV/DVD

Antenna

jack

Antenna

jack

Connections

Connecting to optional equipment

You can enjoy VCR, camcorder or TV game with connection to external input.

INPUT SELECT GAME

Using the audio/video inputs

Press INPUT SELECT repeatedly to select the desired mode. “VIDEO1”, “VIDEO2”, “ColorStream” or TV channel will display on the screen for 4 seconds.

TV Channel VIDEO1

(Rear lower left)

Note: This key will not operate in DVD mode.

ColorStream

VIDEO2

(Left side)

VIDEO1

Connecting to a VCR

To playback from the VCR, connect the VCR to the TV/DVD as shown. Select the “VIDEO2” by pressing INPUT SELECT repeatedly.

: Signal flow

Note: Picture might be muted for some VCR playback. This is not a malfunction of this unit.

VCR

To Audio/Video OUT

Audio/Video cable (not supplied)

(white)

(yellow)

(red)

Left side (LINE 2 IN)

To AUDIO(L/R)/VIDEO IN

The LINE 1 IN terminals can be used in the same way.

Connecting to a camcorder

To playback from the camcorder, connect the camcorder to the TV/DVD as shown. Select the “VIDEO2” by pressing INPUT SELECT repeatedly.

: Signal flow

Camcorder

To Audio/Video OUT

Audio/Video cable (not supplied)

(white)

(yellow)

(red)

Left side (LINE 2 IN)

To AUDIO(L/R)/VIDEO IN

The LINE 1 IN terminals can be used in the same way.

Connecting to a TV Game

You can enjoy playing a TV game on the screen by adjusting to suitable brightness for your eyes.

1. Connect a TV Game to the TV/DVD.

2. Select the “GAME” by pressing GAME. The GAME mode screen appears.

• This TV/DVD has the GAME mode function (see page 24).

: Signal flow

To Audio/Video OUT

Notes:

• You can also change the TV screen to the desired mode by pressing the CH +/– buttons.

• The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. You'll need to consult each component's Owner's Manual for additional information.

• Interactive video games that involve shooting a “gun” type of joystick at on-screen target may not work on this TV/DVD.

Audio/Video cable (not supplied)

(white)

(yellow)

(red)

Left side (LINE 2 IN)

To AUDIO(L/R)/VIDEO IN

Only the LINE 2 IN terminals can be used with the GAME mode.

Connecting to an optional equipment with S-video output

If you connect a VCR with an S-VIDEO cable to the S-VIDEO IN jack on the left side of the TV/DVD, you must also connect the audio cables to the AUDIO IN (LINE 2 IN) jacks on the left side of the TV/DVD. The S-VIDEO cable only carries the video signal. The audio signal is separate. Select the “VIDEO2” by pressing INPUT SELECT repeatedly.

: Signal flow

Ex. VCR with S-Video

To AUDIO (L/R) IN

Left side (LINE 2 IN)

(red)

(white)

(playback)

To S-VIDEO OUT

Note: When the S-VIDEO cable and the standard video cable are connected at the same time, the S-video cable takes precedence.

To Audio (L/R) OUT

Audio cable (not supplied)

S-Video cable (not supplied)

To S-VIDEO IN

Connecting an optional equipment with ColorStream® (Component video) output

Your TV/DVD is capable of using ColorStream® (component video). Connecting your TV/DVD to a component video compatible DVD player, such as a Toshiba DVD player with ColorStream quality and performance.

Ex. DVD player with Component video

: Signal flow

To Component Video OUT

■ Selecting Component input mode

Press INPUT SELECT repeatedly to select “ColorStream” mode.

ColorStream

The ColorStream® inputs on this unit are for use with devices that output 480i interlaced signals and 480p progressive signals. This unit will not accept or display 720p progressive scan signals or 1080i interlaced high-definition signals. If you connect a highdefinition set-top receiver, 720p progressive scan DVD player, or other similar device to the unit’s ColorStream SWITCH THE DEVICE’S OUTPUT TO 480i INTERLACED OR 480p PROGRESSIVE MODE FIRST. Failure to do this will cause a poor or no picture to display.

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet

before making any connections.

• If you place the unit near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the unit away from the tuner and radio.

To AUDIO (L/R) IN

To Audio OUT

Audio cable (not supplied)

Component video cable (not supplied)

When using the Component video cable, an Audio cable must be connected to AUDIO IN (L/R) (LINE 1 IN) jacks.

can greatly enhance picture

Rear lower right of the TV

To COMPONENT

) IN

(Y, P

B, PR

inputs, YOU MUST

Connections

Connecting to optional equipment (Continued)

You can enjoy high quality dynamic sounds by connecting the TV/DVD to optional audio equipment.

This section uses the following reference mark.

: Front speaker : Rear speaker : Sub woofer

: Center speaker : Signal flow

Connecting to an amplifier equipped with a Dolby® Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs encoded via the Dolby Digital recording system with this dynamic realistic sound by connecting the TV/DVD to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Amplifier equipped with a

Dolby Digital decoder

To COAXIAL type digital audio input

75 Ω coaxial cable (not supplied)

To COAXIAL DIGITAL AUDIO OUT

Rear lower left of the TV

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

Connecting to an amplifier equipped with a Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).

■ With an amplifier equipped with a Dolby Digital Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set the amplifier so that you can enjoy Dolby Surround Pro Logic sound.

■ With an amplifier not equipped with a Dolby Digital Connect the equipment as follows.

• This connection is only suitable for Video CDs and Audio CDs.

Amplifier equipped with a Dolby Surround Pro Logic

To COAXIAL type digital audio input

75 Ω coaxial cable (not supplied)

To COAXIAL DIGITAL AUDIO OUT

Rear lower left of the TV

Connect one or two rear speak-

* ers. The output sound from the

rear speakers will be monaural even if you connect two rear speakers.

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs. If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs or audio CDs.

Amplifier equipped with

a DTS decoder

To COAXIAL type digital audio input

75 Ω coaxial cable (not supplied)

Rear lower left of the TV

To COAXIAL DIGITAL AUDIO OUT

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Connecting to an amplifier equipped with an MPEG audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs encoded via the MPEG2 recording system with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.

Amplifier equipped with an

MPEG2 audio decoder

To COAXIAL type digital audio input

75 Ω coaxial cable (not supplied)

Rear lower left of the TV

To COAXIAL DIGITAL AUDIO OUT

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers). Note: PCM audio is limited to DVD or CD playback.

Amplifier equipped with a

Digital audio input

To COAXIAL type digital audio input

Notes:

• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the AC-3 RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD.

• Connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the “COAXIAL” input of a Receiver or Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the TV/DVD to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• The output sound of the TV/DVD has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the TV/DVD’s power cord. If you leave the amplifier’s power on, the speakers may be damaged.

75 Ω coaxial cable (not supplied)

Rear lower left of the TV

To COAXIAL DIGITAL AUDIO OUT

Connections

Basic setup

Power source

Power connection

AC 120V,

To DC input jack

TO USE AC POWER

1. Connect the AC cord to the AC adapter.

2. Connect the AC adapter plug into the TV/DVD’s DC input jack.

3. Connect the AC cord into a wall outlet.

Notes:

Make sure to insert the plug of each cord securely.

• During use the AC adapter becomes warm. This is not a malfunction.

•

WARNING:

DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC ADAPTER OR

• POWER CORD. THIS COULD CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE. DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE DISPLAYED. THIS COULD CAUSE FIRE,

• ELECTRIC SHOCK, OR DAMAGE.

CAUTION:

DO NOT USE THE AC ADAPTER IF IT IS COVERED BY A CLOTH ETC., OR PRESSED INTO A NARROW AREA.

• THIS RESULTS IN POOR DISSIPATION OF HEAT AND MAY CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE. WHEN THIS UNIT IS NOT USED FOR AN EXTENDED PERIOD OF TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF

• SAFETY, BE SURE TO UNPLUG IT FROM THE WALL OUTLET. DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRIC SHOCK.

• IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED AC ADAPTER AND AC

• CORD MUST BE USED. CONTACT THE DEALER THAT YOU PURCHASED THE UNIT FROM.

AC adapter (supplied)

60Hz

AC cord (supplied)

Setting the language

This TV/DVD can display the on screen language in English, Spanish or French in the TV mode. Select the language you prefer first, then proceed with the other menu options.

Setting the language

To turn on the TV/DVD, press POWER.

The Power indicator on the front of the main unit

will light.

Press MENU and then press or to select “SETUP”.

Press or to select “LANGUAGE”, then

or to select the desired language:

press

English (ENGLISH), Spanish (ESPAÑOL) or French (FRANÇAIS), then press ENTER.

Press CANCEL to clear the menu screen.

CANCEL

Notes:

• If the unit does not operate properly, or No key operation (by the unit and/or the remote control): Static electricity,

etc., may affect the TV/DVD’s operation. In such case, disconnect the AC cord once, then connect it again.

• The TV section has its own menu and also DVD section has its own menu

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE

CABLE

TV/CABLE CH PROGRAM

ADD

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE ENGLISH/FRANÇAIS/ESPAÑOL

CABLE

TV/CABLE CH PROGRAM

ADD

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

POWER

CANCEL ENTER

/ / /

Basic setup

To memorize channels

This TV/DVD is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV/DVD’s memory. In addition to normal VHF and UHF channels, this TV/ DVD can receive up to 113 Cable TV channels. To use this TV/DVD with an antenna, set the TV/CABLE selection to the TV position. When shipped from the factory, this selection is in the CABLE position.

TV/CABLE selection

Press MENU in the TV mode, then press or to select SETUP.

Press or to select “TV/CABLE”.

Press or to select “TV” or “CABLE”.

TV - VHF/UHF channels CABLE - Cable TV channels

Press CANCEL to clear the menu screen.

CANCEL

Cable TV chart

The chart below is typical of many cable system channel allocations.

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE

CABLE

TV/CABLE CH PROGRAM

ADD

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE

TV/CABLE

CH PROGRAM

ADD

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE

TV/CABLE

CH PROGRAM

ADD

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

0–9

CANCEL

/ / /

CH +/– MENU

Automatic memory tuning

Press MENU, then press or to select SETUP. Press

or to select the “CH PROGRAM”, then press .

The TV will begin memorizing all the channels available in your area.

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE

CABLE

TV/CABLE

CH PROGRAM

ADD

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

To ADD/ERASE channels

Select the desired channel to be added or deleted

channel selection (0–9) or CH +/–.

using Direct

Press MENU, then press or to select SETUP. Press

Press or to select “ADD” or “ERASE”.

Press CANCEL to clear the menu screen. Repeat steps 1 ~ 3 to add or erase other channel.

CANCEL

or to select “ADD/ERASE”.

PICTURE AUDIO SETUP V-CHIP

SETUP

ENGLISH

LANGUAGE

CABLE

TV/CABLE CH PROGRAM

ADD/ERASE

OFF

CLOSED CAPTION

:SELECT :ADJUST

TV operation

To turn on the TV/DVD, press POWER.

The Power indicator on the front of the main unit

will light.

Adjust the volume level by pressing VOL + or –. The volume level will be indicated on the

screen by white bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of white bars also decreases.

VOLUME 32

Set the TV/ C ABLE selection to the appropriate

position.

TV - VHF/UHF channels CABLE

- Cable TV channels

Auto power off

If a station being viewed stops broadcasting, the TV will automatically shut itself off after 15 minutes.

POWER 0–9

VOL +/–

Press direct channel selection (0–9) to select the channel.

TV mode direct channel selection

When the TV/CABLE selection is in the TV position, all channels can be instantly selected by using two buttons. (for example, to select channel 2, press “0”, then “2”. If you press only “2”, channel selection will be delayed for a few seconds.) For channels 10 and above, press the 2 digits in order.

CABLE mode direct channel selection

When the TV/CABLE selection is in the CABLE position, channels can be selected as follows: TO SELECT CABLE TV CHANNELS: 1-9: Press “0” twice, then 1-9 as needed.

Example, to select channel 2, press “002”.

10-12: Press “0”, then the remaining 2 digits.

Example, to select channel 12, press “012”.

13-99: Press the 2 digits in order. Example, to

select channel 36, press “36”.

100-125: Press the 3 digits in order. Example, to

select channel 120, press “120”.

NOTE FOR CHANNELS 1-12:

If only 1 or 2 buttons are pressed, the corresponding channel will be selected in 2 seconds.

Note:

If a channel with no broadcast is selected, the sound will automatically be muted.

14-69

CATV

VHF

2-13

STD/HRC/IRC

UHF

14-36

(A) (W)

37-59

(AA) (WW)

60-85

(AAA) (ZZZ)

86-94

(86) (94)

95-99

(A-5) (A-1)

100-125

(100) (125)

(5A)

TV operation

ANT

TV operation

TV operation (Continued)

TV operation

■ CHANNEL UP/DOWN

Press and release CH + or –. The channel automatically stops at the next channel set into memory. For proper operation, before selecting channels, they should be set into the memory. See page 22 “To memorize channels”.

ANT

■ RECALL

Press RECALL to display the current informations on the screen. Press RECALL again to clear the display.

• Channel number or external input mode

• Stereo or SAP (Second Audio Program) audio status

STEREO SAP

ANT

■ CH RETURN

This button allows you to go back to the last channel selected by pressing CH RTN. Press CH RTN again to return to the last channel you were watching.

ANT

■ MUTE

Press MUTE to switch off the sound. The TV/DVD’s sound will be silenced and “MUTE” will appear briefly on the screen. The sound can be switched back on by pressing this button again or one of VOL +/–.

SLEEP RECALL

CH RTN MUTE VOL +/– GAME CH +/–

■ SLEEP

To set the TV/DVD to turn off after a preset amount of time, press SLEEP on the remote control. The clock will count up 10 minutes for each press of SLEEP (0h00m, 0h10m,... 1h50m, 2h00m). After the sleep time is programmed, the display will appear briefly every ten minutes to remind you that the sleep timer is operating. To confirm the sleep timer setting, press SLEEP and the remaining time will be displayed for a few seconds. To cancel the sleep timer, press SLEEP repeatedly until the display turns to 0h00m.

SLEEP

0h00m

■ GAME MODE

After connecting a TV Game to the unit (see page 16), press GAME. The TV screen changes to the Game mode.

GAME

• The Game mode screen is adjusted to the suitable brightness for your eyes.

• If GAME is pressed during standby mode, the unit turns on automatically and the Game mode screen appears on the screen.

• Interactive video games that involve shooting a “gun” type of joy-stick at an on-screen target may not work on this TV/DVD.

■ HEADPHONES

Insert a stereo headphones (not supplied) with a 1/8” mini plug into the PHONES jack on the front panel. If you connect headphones, the sound from TV speakers is muted.

Closed captions

WHAT IS CLOSED CAPTIONING?

This television has the capability to decode and display closed captioned television programs. Closed captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language.

CLOSED CAPTION

Closed captions

Captions: This closed caption mode will display text on the screen in English or another language (depending

on the setting of the closed captions CH 1/2). Generally, closed captions in English are transmitted on captions channel 1 and closed captions in other languages are transmitted on captions channel 2.

Text: The text closed caption mode will usually fill the screen with a programming schedule or other information. After selecting a closed caption mode, it will stay in effect until it is changed, even if the channel is changed. If the captions signal is lost due to a commercial or a break in the signal, the captions will reappear when the signal is received again. If the channels are changed, the captions will be delayed approximately 10 seconds. The captions will appear in places on the screen where they will least interfere with the picture, usually on the bottom of the screen. News programs will usually show three-line closed captions which scroll onto the screen. Most other shows provide two or three lined captions placed near the character who is speaking so the viewer can follow the dialogue. Words in italics or underlined describe titles, words in foreign languages or words requiring emphasis. Words that are sung usually appear enclosed by musical notes. For television programs broadcasting with closed captions, look in your TV guide for the closed captions symbol (CC).

TO VIEW CLOSED CAPTIONS

Press CLOSED CAPTION to switch between normal TV and the two closed caption modes (captions and full screen text). Closed captioning will display text on the screen for hearing impaired viewers.

• You can also select the closed captions in SETUP menu in the TV mode.

CLOSED CAPTION OFF

Notes:

• When selecting closed captions, the captioning will be delayed approximately 10 seconds.

• If no caption signal is received, no captions will appear, but the television will remain in the caption mode.

• Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with closed captioning, especially with live programs. This is because during live programs, captions are also entered live. These transmissions do not allow time for editing.

• When captions are being displayed, on-screen displays, such as volume and mute may not be seen or may interfere with closed captions.

• Some cable systems and copy protection systems may interfere with the closed captioned signal.

• If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or may appear with strange characters or misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna.

TV operation

MUTE

TV operation

Setting the V-Chip

An age limitation can be set to forbid children to see and hear violent scenes or pictures for adults, etc. The TV/DVD corresponds to “TV RATING” and “MOVIE RATING”. To use the V-Chip function, you must register a password.

Notes:

• If you forget the password, you cannot set the V-Chip.

• To avoid forgetting the password, write it down and keep in the safe place.

To register password

Press MENU and then press or to select V-CHIP.

PICTURE AUDIO SETUP V-CHIP

V-CHIP

OFF

V-CHIP

OFF

TV RATING

OFF

MOVIE RATING

NEW PASSWORD

:SELECT :ADJUST

Press or . New password entering screen appears.

Enter the password (4 digits) using Number buttons (0–9), then press ENTER.

PICTURE AUDIO SETUP V-CHIP

V-CHIP

----

NEW PASSWORD

[0-9]:SELECT ENTER:SET

CANCEL:END

PICTURE AUDIO SETUP V-CHIP

V-CHIP

NEW PASSWORD

[0-9]:SELECT ENTER:SET

CANCEL:END

“ ” appears instead of the number.

Enter the same password again for the safety, then press ENTER.

Now the password was registered and V-Chip setting menu will appear on the display.

PICTURE AUDIO SETUP V-CHIP

V-CHIP

CONFIRM PASSWORD

[0-9]:SELECT ENTER:SET

CANCEL:END

0–9

CANCEL ENTER

/ / /

To change password

Repeat steps 1 ~ 3 in “To register password” on left, then press

PASSWORD”, then press

Enter the new password using Number buttons (0–9), then press ENTER.

Enter the same password again using Number buttons (0–9) for safety, then press ENTER.

Press CANCEL to clear the menu screen.

CANCEL

Note:

The V-Chip feature is available only for the U.S. V-Chip system. The Canadian V-Chip system is not supported.

or to select “NEW

PICTURE AUDIO SETUP V-CHIP

V-CHIP

OFF

V-CHIP

OFF

TV RATING

OFF

MOVIE RATING

NEW PASSWORD

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

V-CHIP

----

NEW PASSWORD

[0-9]:SELECT ENTER:SET

CANCEL:END

PICTURE AUDIO SETUP V-CHIP

V-CHIP

CONFIRM PASSWORD

[0-9]:SELECT ENTER:SET

CANCEL:END

To set the V-Chip

Repeat steps 1 ~ 3 in “To register password” on page 26, then press

“TV RATING”.

Press

or to select the desired rating.

OFF : TV RATING is not set TV-Y : All children TV-Y7 : 7 years old and above TV-G : General audience TV-PG: Parental guidance TV-14 : 14 years old and above TV-MA: 17 years old and above

When you select TVY7, TV-PG, TV-14 or TV-MA, press RECALL to show the contained rating.

/ or /

Press to select the desired item you want.

Press or to select “MOVIE RATING”.

or to select

PICTURE AUDIO SETUP V-CHIP

V-CHIP

TV RATING OFF/TV-Y/TV-Y7/TV-G TV-PG/TV-14/TV-MA

MOVIE RATING

NEW PASSWORD

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

V-CHIP

TV RATING OFF/TV-Y/TV-Y7/TV-G TV-PG/TV-14/TV-MA

MOVIE RATING

NEW PASSWORD

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

V-CHIP

V-CHIP TV RATING

MOVIE RATING OFF/G/PG/PG-13/R/NC-17/X

NEW PASSWORD

:SELECT :ADJUST

Press

or to select

OFF

OFF : MOVIE RATING is not set G:All ages PG : Parental guidance PG-13 : Parental guidance

less than 13 years old

R:Under 17 years old

Parental guidance suggested

NC-17 : 17 years old and above X:Adult only

Press or to select “V-CHIP”.

OFF

TV-Y

OFF

OFF TV-Y

OFF

Press or to display “ON”.

Now your settings were set into the memory.

Press CANCEL to clear the menu screen.

CANCEL

To use after the TV is protected

When you try to view a program with a ratings block, a message will appear listing the program’s ratings. The program can still be viewed if you press MUTE and then enter your password to temporarily bypass the block.

Note:

The V-Chip function is activated only on programs that have the rating signal.

RECALL CANCEL

ENTER

/ / /

the desired rating.

PICTURE AUDIO SETUP V-CHIP

V-CHIP

OFF

V-CHIP

TV-Y

TV RATING

PG-13

MOVIE RATING OFF/G/PG/PG-13/R/NC-17/X

NEW PASSWORD

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

V-CHIP

ON/OFF

V-CHIP

TV-Y

TV RATING

PG-13

MOVIE RATING

NEW PASSWORD

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

V-CHIP

ON/OFF

V-CHIP

TV-Y

TV RATING

PG-13

MOVIE RATING

NEW PASSWORD

:SELECT :ADJUST

TV operation

Picture control adjustment/ Adjusting the picture mode

Picture controls are factory preset but you can adjust them individually as follows: And also you can select four picture modes—Standard, Sports, Movie, and Memory—as described in the following table:

Picture control adjustment Adjusting the picture mode

Press MENU and then press or to select “PICTURE”.

Press or to select the item you want to adjust, then press

Selection Pressing

BRIGHTNESS darker lighter CONTRAST lower higher COLOR paler deeper TINT reddish greenish SHARPNESS softer sharper

Note:

The CONTRAST default setting is set to maximum (+50) at the factory.

Press CANCEL to clear the menu screen.

CANCEL

■ To return all adjustments to the factory preset levels

Press

or to select “RESET”, then press .

PICTURE AUDIO SETUP V-CHIP

PICTURE

SPORTS

MODE

BRIGHTNESS

CONTRAST

COLOR

TINT

SHARPNESS

:SELECT :ADJUST

or to adjust the setting.

PICTURE AUDIO SETUP V-CHIP

PICTURE

SPORTS

MODE

BRIGHTNESS

CONTRAST

COLOR

TINT

SHARPNESS

:SELECT :ADJUST

Press MENU and then press or to select “PICTURE”.

Press or to select “MODE”, then press

or to select the desired picture mode.

Mode Picture quality

SPORTS Bright and dynamic picture (factory-set) STANDARD Standard picture quality (factory-set) MOVIE Movie-like picture setting (factory-set) MEMORY Your personal preferences (set by you;

see “Picture control adjustment” as left)

Press CANCEL to clear the menu screen.

CANCEL

Note:

You cannot select “MODE” in the Game mode.

PICTURE AUDIO SETUP V-CHIP

PICTURE

MODE

BRIGHTNESS CONTRAST COLOR TINT SHARPNESS

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

PICTURE

MODE SPORTS/STANDARD/MOVIE/MEMORY

BRIGHTNESS CONTRAST COLOR TINT SHARPNESS

:SELECT :ADJUST

CANCEL

/ / /

SPORTS

25 50 25

SPORTS

25 50 25

Selecting the color temperature

Press MENU and then press or to select “PICTURE”

Press or to select “COLOR TEMPERATURE”.

Press or to select the desired color mode.

Mode Picture quality

COOL Bluish MEDIUM Neutral WARM Reddish

Press CANCEL to clear the menu screen.

CANCEL

PICTURE AUDIO SETUP V-CHIP

PICTURE

SPORTS

MODE

BRIGHTNESS

CONTRAST

COLOR

TINT

SHARPNESS

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

PICTURE

COLOR

COOL

TEMPERATURE COOL/MEDIUM/WARM

RESET

:SELECT :ADJUST

PICTURE AUDIO SETUP V-CHIP

PICTURE

COLOR

WARM

TEMPERATURE COOL/MEDIUM/WARM

RESET

:SELECT :ADJUST

CANCEL

/ / /

TV operation

Sound control adjustment/ Stereo and Second Audio Program (SAP)

Sound controls are factory preset but you can adjust them individually as follows:

The TV/DVD is equipped with a feature known as multi-channel TV sound or MTS. MTS broadcasts greatly enhance TV viewing by bringing you programs with high fidelity stereo sound. MTS also provides an extra channel called the Second Audio Program or SAP which broadcasters can use to transmit a second language for bilingual transmission or for other purposes.

Sound control adjustment

Press MENU and then press or to select “AUDIO”

Press or to select the item you want to adjust, then press

MTS

Press

or to select “STR” (STEREO), “SAP” or

“MONO”.

BASS:

Press

or to adjust the bass sound.

TREBLE:

Press

or to adjust the treble sound.

BALANCE:

Press

or to obtain an equal sound level from

both speakers.

SURROUND:

Press

or to select “ON” or “OFF”.

ON:

The dynamic presence and sound created offers a thoroughly enjoyable listening experience.

OFF: Normal sound.

Press CANCEL to clear the menu screen.

CANCEL

■ To return BASS/TREBLE/BALANCE control adjustments to the factory preset levels

or to select “RESET”, then press .

Press

PICTURE AUDIO SETUP V-CHIP

AUDIO

MTS BASS TREBLE BALANCE SURROUND RESET

:SELECT :ADJUST

or to adjust the setting.

PICTURE AUDIO SETUP V-CHIP

AUDIO

MTS

BASS

TREBLE BALANCE SURROUND RESET

:SELECT :ADJUST

STEREO 25 25

OFF

STEREO

OFF

Listening to stereo sound

Repeat step 1 in “Sound control adjustment” on left, then press Then press When the TV is turned on or a channel selection is made, the “STEREO” will appear on the screen. This means that Stereo broadcasting is available. You can enjoy stereo sound from the left and right speakers.

• When mono broadcasting is received, no indication is

displayed.

• If the broadcast signal is not strong enough or clear stereo sound is not available, select “MONO”. The noise may be eliminated.

Listening to SAP (Second Audio Program)

Repeat step 1 in “Sound control adjustment” on left, then press Then press When the TV is turned on or a channel selection is made, the “SAP” will appear on the screen. This means that the Second Audio Program broadcasting is available.

or to select “MTS”.

or to select “STR”.

STEREO

or to select “MTS”.

or to select “SAP”.

STEREO SAP

CANCEL

/ / /

Note:

You cannot select “COLOR TEMPERATURE” in the Game mode.

Basic playback

Playing a disc

This section shows you the basics on how to play a disc.

CAUTION

Keep your fingers well clear of the disc slot when disc is loading or unloading. Neglecting to do so may cause serious personal injury.

DVD VCD

Basic playback

Preparations:

• When connecting to other equipment, turn the power off.

Press POWER on the unit or on the remote control to turn on the unit.

The Power indicator on the front of the main unit will light.

• Every time you press POWER, the TV/DVD starts from TV mode.

• When using an amplifier, switch on the amplifier.

Press TV/DVD on the remote control to select DVD mode.

The DVD startup screen will appear on the screen.

Load a disc in the disc slot.

Load the disc in the disc slot with the label side facing forward. (If the disc has a label.) Hold the disc without touching either of its surfaces, align it with the guides, and place it in position.

POWER

VOLUME

On the TV-screen, “0” changes to “Reading” and then playback commences.

• A menu screen will appear on the TV screen if the disc has a menu feature.

/ or / to select title, then press

Press

ENTER. Title is selected and play commences.

Press VOLUME + or – to adjust the volume.

Press STOP to end playback.

■ To start playback in the stop mode

Press PLA Y.

PLAY STOP EJECT

/–

Reading

VOLUME 32

■ Resuming facility

• The unit records the stopped point, depending on the disc. “

” appears on the screen. Press PLAY to resume playback (from the scene point).

• If you press STOP again (“■” appears on the screen.), the unit will clear the stopped point.

Basic playback

Note: If the unit does not operate properly:

Static electricity, etc., may affect the TV/DVD’s operation. In such

case, disconnect the AC cord, then connect it again.

Basic playback

Playing a disc (Continued)

To obtain a higher quality picture

Occasionally, some picture noise may appear on the TV screen while playing a DVD video disc because the high resolution pictures on these discs include a lot of information. In such case, you may reduce the SHARPNESS with the Picture control adjustment menu (see page 28).

DVD VCD CD

About

DVD VCD CD

The function described under that heading.

VCD

DVD VCD CD

To pause playback (still mode)

Press PAUSE during playback.

To stop playback

Press STOP.

Notes:

• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen

according to the type of loaded disc. In this case, check your disc again (see pages 8 and 50).

• Some discs may take a minute or so to start playback.

• When you set a single-faced disc label downwards (ie. the wrong way up), “Reading” will appear on the display for a few

minutes and then “Incorrect Disc” will continue to be displayed.

• Some discs may not work the resuming facility.

• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page 39.

• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according

to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.

• Do not move the unit during playback. Doing so may damage the disc.

• Use the EJECT button to unload and eject the disc.

• Do not put any objects other than discs on the disc slot. Doing so may cause the unit to malfunctions.

• There may be a slight delay between the button is pressed and the function activates.

icons on the heading bar show the playable discs for the

: You can use this function with DVD video discs. : You can use this function with Video CDs. : You can use this function with Audio CDs and CD-R/RW CDs.

Basic playback

To resume normal playback, press PLAY.

• The sound is muted during still mode.

To remove the disc

Press EJECT.

Remove the disc after the disc comes out.

POWER TV/DVD

EJECT

VOL +/– ENTER

/ / /

PAUSE PLAY STOP

REV PLAY

PAUSE FWD

SKIP SLOW /

DVD VCD

Playing in fast reverse or fast forward directions

Press REV or FWD during playback.

REV: Fast reverse playback FWD: Fast forward playback

Each time you press REV or FWD button, the playback speed changes.

DVD

Playing frame by frame

VCD

Press PAUSE during still playback.

DVD VCD

Press SLOW (REVERSE) or (FORWARD) during playback.

DVD VCD CD

Press SKIP or repeatedly to display the chapter or track number you want.

Playback starts from the selected chapter or track.

Note:

A “Prohibition” symbol “✕” may appear at the upper right of the screen. This symbol means either the feature you tried is not available on the disc, or the TV/DVD cannot access the feature at this time. This does not indicate a problem with the TV/DVD.

Each time you press PAUSE, the picture advances one frame.

Playing in slow-motion

Each time you press the button, the slow-motion speed changes.

Locating a chapter or track

To locate succeeding chapters or tracks.

To resume normal playback

Press PLA Y.

Notes:

• The TV/DVD mutes sound during reverse and forward scan of DVD and Video CD discs. Howerer, the TV/DVD plays sound during fast forward or fast reverse play of audio CDs.

• The playback speed may differ depending on the disc.

To resume normal playback

Press PLA Y.

Note:

The sound is muted during frame by frame playback.

To resume normal playback

Press PLA Y.

Notes:

• The sound is muted during slow-motion playback.

• The Video CD cannot play Reverse Slow.

Playback starts from the beginning of the current chapter or track. When you press twice in quick successions, playback starts from the beginning of the preceding chapter or track.

Basic playback

Advanced playback

Zooming/Locating desired scene

DVD VCD

Zooming

This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.

Press ZOOM during playback.

Notes:

•You can select the Pause, Slow or Search playback in the zoom mode.

•Some discs may not respond to zoom feature.

The center part of the image will be zoomed in. Each press of ZOOM will change the

1 (x 1.3), 2 (x 1.5) and 3

ZOOM (x 2.0).

Press / / / to view a different part of the frame.

In the zoom mode, press ZOOM repeatedly to return to a 1:1 view (

You may move the frame from the center position to UP, DOWN, LEFT or RIGHT direction.

Off).

0–9 ZOOM

JUMP CANCEL ENTER

/ / /

RECALL

DVD VCD

Locating desired scene

Use the title, chapter and time recorded on the DVD disc to locate the desired point to playback. In the case of VCD/CD discs, time and track are used to locate the desired point to playback. To check the title, chapter and time, press RECALL.

Press JUMP during playback or resume stop mode.

Press or to select the “Time”, “Title/Track” or “Chapter”.

Press Number buttons (0–9) to input the number.

• If you input a wrong number, press CANCEL.

• Refer to the package supplied with the disc to check the numbers.

Press ENTER. Playback starts.

Note:

In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page

• When you change the title,

playback starts from Chapter 1 of the selected title.

• Some discs may not work in the

above operation.

Jump Title Chapter Time

Jump Title Chapter 12 Time

Repeat playback/A-B Repeat playback

DVD

Repeat playback

VCD

Press PLAY MODE during playback or stop mode.

[DVD] Press ENTER to select “Chapter” or “Title”.

[Video CD] Press Press ENTER to select “Track” or “All”.

• If you set the repeat mode during stop mode, press PLAY to start Repeat playback.

[Audio CD and MP3/WMA CD] Please “Repeat playback (CD)”

Press PLAY MODE again to clear the screen.

To resume normal playback

Select Repeat : “Off” in step 2.

Notes:

• Some discs may not work with the repeat operation.

• In case of Video CD with PBC, Repeat functions are prohibited during playback.

• Chapter/Track repeat function is canceled whenever SKIP

or is pressed.

The unit automatically starts repeat playback after finishing the current title or chapter.

Repeat : Off

to select “Repeat”.

The unit automatically starts repeat playback after finishing the current track.

Mode : Off

Repeat : Off

Play Mode

A-B repeat playback allows you to repeat a section between two selected points.

Press REPEAT A-B again.

Notes:

• In A-B Repeat mode, subtitles near the A or B locations may

• You cannot set the A-B Repeat for the scenes that include

• A-B Repeat playback does not work when Repeat playback is

• You may not be able to set A-B Repeat, during certain scenes

• A-B Repeat does not work with an interactive DVD, MP3/WMA/

• A-B Repeat is prohibited when PBC is on.

DVD

A-B Repeat playback

VCD

Press REPEAT A-B during playback.

To resume normal playback

not be displayed.

multiple angles.

activated.

of the DVD.

JPEG CD.

The start point is selected.

Press REPEAT A-B again.

The end point is selected. Playback starts at the point that you selected. Playback stops at the end point and returns to Point A automatically, then starts again.

” appears on the screen.

“

Off

PLAY MODE

ENTER PLAY

SKIP

REPEAT A-B

Advanced playback

Program playback/Random playback

You can arrange the playback order of tracks or files on the disc. And the unit can also select tracks or files at random and playback them. These feature works for Video CD.

For Audio CD and MP3/WMA CD, please see “Random playback

(CD)”

and “Program playback (CD)” 45.

VCD

Program playback

Press PLAY MODE in the stop mode.

Press or to select “Mode”, then press ENTER to select “Program”.

Press / to select the programming position. Use Number buttons (0–9) to input the Track on

sequentially.

VCD

Random playback

Press PLAY MODE during playback or stop mode.

Press / to select “Mode”, then press ENTER to select “Random”.

Play Mode

Mode : Off

Repeat : Off

Program Playback

Mode : Program

Repeat : Off

Program Playback

• To program others, repeat step 3.

• If you input a wrong number, press

CANCEL.

Mode : Program Repeat : Off

Program Playback

Mode : Random

Repeat : Off

Program Playback

Play Mode

1 — — — 2 — — — 3 — — —

1 – – – 2 – – – 3 – – –

1 9

2 – – – 3 – – –

1 – – – 2 – – – 3 – – –

0–9

CANCEL PLAY MODE

▲ /▼ / ENTER

PLAY

Press / to return to the left column, then

/ to select the “Program Playback”

press

and press ENTER.

The programs you selected will start to playback in order.

• To resume normal playback, select Mode: “Off” in step 2.

Play Mode

Mode : Program Repeat : Off

Program Playback

■ To change the program

1. Select Mode to “Program” (as step 2), press to select the track/file number you want to change, then press CANCEL.

2. Press Number buttons (0–9) to overwrite the new track/file number.

■ To clear the program one by one

Select Mode to “Program”, press track number. Then press CANCEL.

■ To clear all the programs

In the left column, press Then press ENTER.

Notes:

• In playing back the Video CD with PBC, you cannot set Program playback.

• The program is canceled when you eject the disc or turn the power off.

Press PLAY

• If you set “Random” during playback mode, Random playback will begin after the track/file that is currently being played has ended.

• To resume normal playback, select Mode: “Off” in step 2.

Note:

In case of Video CD with PBC, you cannot set Random function during playback.

/ to select “Clear Program”.

The Random Playback will start.

1 9 2 3 3 11

/ / /

/ / / to select the

Changing angles/Title selection/DVD menu

TOP MENU DVD MENU

▲ /▼ / ENTER

PLAY

ANGLE

Changing angles

When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.

Press ANGLE during playback.

The current angle will appear.

1/2

Title selection

Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.

Press TOP MENU during playback.

1 2

Title menu appears on the screen.

Press / / / to select the desired title.

DVD menu

Some DVDs allow you to select the disc contents using the menu. When you playback these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.

Press DVD MENU during playback.

1 2

The DVD menu appears on the screen.

• Press DVD MENU again to resume playback at the scene when you pressed DVD MENU.

Press / / / to select the desired item.

Press ANGLE repeatedly until the desired angle is selected.

Note:

Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.

Press ENTER or PLAY.

Note:

Depending on the DVD, you may not be able to select the title. Depending on the DVD, a “title menu” may simply be called a “menu” or “title” in the instructions supplied with the disc.

Note:

Depending on the DVD, you may not be able to resume playback from the scene point when you press the DVD MENU button.

The playback of the selected title will start.

Press ENTER.

The menu continues to another screen. Repeat steps 2 and 3 to set the item completely.

Advanced playback

Changing soundtrack language/ Subtitles

DVD

Changing soundtrack language

VCD

You can select the language when you play a multilingual disc.

Press AUDIO during playback.

In case of Video CD playback

Audio type changes as follows each time you press AUDIO.

Notes:

• If the desired language is not heard after pressing the button several times, the language is not recorded on the disc.

• The selected soundtrack language is canceled when you eject the disc. The initial default language or available language will be heard if the disc is played back again.

• If you select DTS in playing DTS-encoded disc, no sound will be heard from the TV/DVD’s speakers.

The current soundtrack language will appear.

Press AUDIO repeatedly until the desired language is selected.

• The on screen display will disappear after a few seconds.

1/2 Eng Dolby Digital

2/2 Fre Dolby Digital

L R

SUBTITLE AUDIO

Subtitles

When playing back a disc recorded with subtitles, you can select the subtitle language or turn the subtitle off.

Press SUBTITLE repeatedly during playback until the desired language is selected.

To turn off the subtitle, press SUBTITLE until “Off” appears.

• The on screen display will disappear after a few seconds.

Notes:

• Depending on the DVD, you may not be able to change subtitles, or to turn subtitles on or off.

• While playing a DVD, the subtitle may change when you loaded or eject the disc.

• In some cases, a selected subtitle language may not be changed immediately.

1/5 Eng

Off

Disc status/To turn off the PBC

DVD

Disc status

VCD

With each press of RECALL, the status of the disc will appear on the screen and change as follows. To cancel the display, press RECALL again.

DVD

DISC OPERATION

TITLE NO.

ANGLE NO.

AUDIO LANGUAGE A KIND OF AUDIO

Video CD

DISC OPERATION

ELAPSED TIME

DVD 00:15:25 01:41:39 Title 1/3 Chapter2/24

1/1 Eng Dolby Digital 1/2 Eng 1/1

SUBTITLE LANGUAGE

ELAPSED TIME

VCD 00:08:32 00:51:03 Track 3/15

TRACK NO.

TOTAL TIME

CHAPTER NO.

RECALL

PLAY MODE

ENTER

VCD

To turn off the PBC (see page 8)

Press PLAY MODE in the stop mode.

Press / to select “Mode”, then press ENTER repeatedly until “Off” appear.

Press PLAY MODE again to clear the screen.

■ To turn on the PBC

Follow the above steps 1~2, then press ENTER repeatedly until “PBC” appear.

Note:

You can also turn off the PBC by pressing number button 1 and ENTER in the stop mode.

Mode : Off

Repeat : Off

Program Playback

Play Mode

1 — — — 2 — — — 3 — — —

Advanced playback

MP3/WMA/JPEG/DivX® and Audio CD operation

This player can playback the MP3/WMA/JPEG/DivX®-data which has been recorded on CD-R or CD-RW. To produce the MP3/

WMA/JPEG/DivX supplied). The Apple-HFS-System cannot be played.

This player requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality. There are many different types of recordable disc formats (including CD-R containing MP3/WMA files). Not all recordable discs will produce optimal playback quality. The technical criteria set forth in this owner's manual are meant only as a guide. Use of CD-RW for MP3 files is not recommended.

You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission.

Limitations on MP3/WMA/JPEG/DivX® CD playback

• MP3/WMA/JPEG/DivX® CD is the disc that is standardized by ISO9660, its file name must include 3-digits extension letters, “.mp3”, “.wma”, “.jpg”, “.div”, “.divx”, “.avi”.

• MP3/WMA/JPEG/DivX

• This unit can read 600 files per disc. If one directory has more than 600 files, it reads up to 600 files, the remaining files will be omitted.

• The unit is able to recognize up to a maximum of 50 directories per disc.

• MP3/WMA/JPEG/DivX

• If the CD has both CDA audio tracks and MP3/WMA/JPEG/DivX

• It may take more than one minute for this unit to read MP3/WMA/JPEG/DivX

• Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 15 letters) on the screen. Long file names will be condensed.

• The music files recorded by “Hierarchical File System” (HFS) cannot be played.

Limitations on display

• The maximum number for display is 15 letters. Available letters for display are the following: capital or small alphabets of A through Z, numbers of 0 through 9, and _ (under score).

• Other letters than those above are replaced in hyphen.

Notes on MP3/WMA/JPEG/DivX

To playback MP3/WMA/JPEG/DivX

1. Use MP3/WMA/JPEG/DivX® software that records data alphabetically or numerically.

2. Name each file including two-digit or three-digit number (ex. “01” “02” or “001” “002”).

3. Refrain from making too many sub-folders.

CAUTION:

• Some MP3/WMA/JPEG/DivX

• The CD-R/RW that has no music data or non MP3/WMA/JPEG/DivX

Standard, sampling frequency, and the bit rate:

MP3 CD

MPEG-1 Audio 32kHz, 44.1kHz, 48kHz 32kbps ~ 320kbps (constant bit rate or variable bit rate) The recommend recording setting for a high-quality sound is 44.1kHz of sampling frequency and 128kbps of constant bit rate.

WMA CD

WMA version 7, and 8 32kHz/48kbps, 44.1kHz/48kbps~192kbps, 48kHz/128kbps~192kbps The file recorded by mono, 48kHz, 48 kbps is not available to this unit.

DivX® video

DivX® version: DivX® 3, 4, 5, and 6 (specifically 3.1.1, 4.1.2, 5.0.2, 5.0.5, 5.1.1, 5.2.1, 6.0 at Home Theater profile). Audio format: MPEG1 Layer2 (MP2), MPEG1 Layer3 (MP3) Sampling frequencies: 32kHz, 44.1kHz, 48kHz Bit rate: 32kbps ~ 320kbps Resolution: Max 720 x 576 (at 25fps), Max 720 x 480 (at 30fps)

Microsoft, Windows Media, and Windows Logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

-data, you need a Windows-PC with CD-RW drive and a MP3/WMA/JPEG/DivX®-encoding Software (not

CD/MP3/WMA/JPEG/DivX® CD information

CD must be correspond to the ISO standardized files.

CDs cannot be used for the purpose of recording.

files

CD in the recorded order,

CDs cannot be played back depending on the recording conditions.

files, only the CDA audio tracks will be played.

files depending on its structure.

files cannot be played back.

MP3/WMA CD playback

Load a disc on which MP3 or WMA files have been recorded in the disc slot.

A file browser screen will appear on the screen.

Press / to select file.

• In case the current directory includes more than 8

or to scroll in the file list.

files, press

• To see contents in folder, select the folder and then press ENTER. To return to the upstairs directory,

Go Up ...” then press ENTER.

select “

• When PLAY is pressed after the file browser displayed, playback begins automatically starting from the first file. In this case, if the first file is an MP3/WMA file, only MP3/WMA files are played back in order. If the first file is a JPEG file, the first JPEG file is played back. If the first file is a

first DivX

file is played back. If there is no file at a

root directry, playback does not begin automatically.

Press ENTER.

The selected file starts playing back.

Press STOP to end playback.

• The unit records the stopped point. “ ” appears on the screen. Press PLAY to resume playback (from the scene point).

• If you press STOP again or unload the disc, the unit will clear the stopped point.

Folder-1

Folder-2 MP3-1 MP3-2 MP3-3 WMA-1 WMA-2 WMA-3

/MP3-2.MP3

Folder-1 Folder-2 MP3-1

MP3-2

MP3-3 WMA-1 WMA-2 WMA-3

DivX® file, the

SelectFiles Repeat :Off Mode :Off

JPEGPreview

Select Files

Repeat :Off Mode :Off

JPEG Preview

TOP MENU ▲ /▼ / /

ENTER RETURN PLAY STOP

About file menu

3/15 00:00:00

/Folder-1/WMA-11.WMA

MP3-5 MP3-6

WMA-11

WMA-12 Picture-1 Picture-2 Movie-1 Movie-2

Notes:

• The thumbnail list is displayed when the FUJICOLOR CD or the Kodak Picture CD are played. To display the file browser, press TOP MENU.

• In the case of a CD containing a mixture of MP3, WMA, JPEG and DivX selecting them from the file browser.

• MP3 or WMA file on the Kodak Picture CD is not recognized on this unit.

Notes:

• During MP3/WMA/JPEG Playback, you cannot use JUMP and A-B Repeat functions.

• You can use Repeat (Track or All), Random functions and Program playback for MP3/WMA/JPEG/DivX

, 45.

Select Files

The file type to make it display in the file browser can be chosen.

or to highlight “Select Files” at right column

1.Press

in the file browser.

2. Press ENTER, then press

from the list (Music, Picture or Movie).

3.Press ENTER to add/remove check mark. Checked

file type will be displayed in the file browser.

4.Press RETURN to save the setting.

Select Files Repeat :Off Mode :Off

Music Playing

files, the files are played back by

or to select file type

CD Playback

Advanced playback

MP3/WMA/JPEG/DivX® and Audio CD operation (Continued)

You can select your desired JPEG file on the file menu and picture menu. The selected JPEG file is automatically adjusted to the TV screen. (When the aspect ratio of the JPEG file is different to the TV screen, the black bar will appear at the top and bottom, or the both sides of the TV screen.)

CD CD

JPEG CD playback

Load a JPEG disc in the slot.

A file browser screen will appear on the

screen.

Press / to select the file. To display a thumbnail list, press DVD MENU.

/ or / to select the desired file.

Press (To return to a file browser, press TOP MENU.)

• When PLAY is pressed after displaying the file browser, playback begins starting from the first file. In this case, file is a JPEG file, the first JPEG file is played back. If the first file is a DivX

file is played back.

DivX If the first file is an MP3/WMA file, only MP3/ WMA files are played back in order. If there is no file at a root directory, playback does not begin automatically.

Press ENTER or PLAY. The selected picture appears on the screen.

Rotating an image

You can rotate an image by 90 degrees. Press ANGLE during playback of the image.

”, “ ”, “ ” or “ ” appears on the screen.

“

Press STOP to end playback.

The file browser appears on the screen. If you want to watch the other file, repeat steps 3 ~ 4.

/Picture-01.JPG

Picture-01

Picture-02 Picture-03 Picture-04 Picture-05 Picture-06 Picture-07 Picture-08

automatically

file, the first

The slide show enables you to view pictures (files) one after another automatically.

Preparation:

• Set “JPEG Interval” setting to “5 Seconds”, “10 Seconds”

Select Files

or “15 Seconds”

Repeat :Off Mode :Off

JPEG Preview

W: 2048 H: 1536

• If you press PAUSE during the slide show, the slide

if the first

• When the slide show playback finished, the file list

• To stop the slide show, press STOP. The file list appears.

Notes:

• Zoom function also can be used in viewing JPEG files. See “Zooming”

• During JPEG playback, you cannot use Jump and A-B Repeat functions.

STOP TOP MENU

DVD MENU ▲ /▼ / / ENTER PAUSE

PLAY SKIP ¢

ANGLE

Slide show playback

Select your desired starting file for the slide show in the step 3 on left.

Press ENTER or PLAY to start slide show from the selected file.

show stops temporary. “;” appears briefly on the screen. If the picture appears upside down or sideways, press ANGLE repeatedly until it’s right side up.

”, “ ”, “ ” or “ ” appears on the screen.

“ Press PLAY or SKIP again to resume the slide show .

appears.

DivX® CD playback

Load a disc on which DivX® files have been recorded in the slot.

A file browser screen will appear on the screen.

Press / to select file.

• When PLAY has been pressed after displaying the file browser, playback begins automatically starting from the first file. In this case, if the first file is a JPEG file, the first JPEG file is played back. If the first file is a

file is played back. If the first file is an

DivX

MP3/WMA file, only MP3/WMA file are played back in order. If there is no file at a root directory, playback does not begin automatically.

Press ENTER or PLAY. The selected DivX movie will be played back on the screen.

Press STOP to end playback.

/Movie-01.DIVX

Movie-01

Movie-02 Movie-03 Movie-04 Movie-05 Movie-06 Movie-07 Movie-08

DivX® file, the first

The file browser appears on the screen. If you want to watch the other file, repeat steps 3 ~ 4.

Playing DivX® VOD content

DivX® VOD content is protected by DRM (Digital Rights Management) system. This restricts playback of content to specific registered devices.

If the incorrect DRM file is loaded, “Authorization

Select Files

Error This player is not

Repeat :Off Mode :Off

authorized to play this video.” will appear on the

JPEG Preview

screen. When you attempt to play

VOD, the number of

DivX plays is limited and the right message will appear on the screen. If you wish to play it, select “YES”.

• If the number of plays goes over the limit, then “Rental Expired” will be displayed, in this case the file will not be played.

Note:

In order to play DivX need to register the unit with registration code. See page

VOD content on this unit, you first

STOP ▲ /▼

ENTER PLAY

View DivX® VOD Rental

This rental has 5 views left.

Do you want to use one

of your 5 views now?

NoYes

Advanced playback

Repeat and program playback using file browser

CD CD

Repeat playback (CD)

In the file browser, press / or / to select “Repeat” during stop mode.

Folder-1 Folder-2 MP3-1 MP3-2

Press ENTER to select “Track” or “All”.

Folder-1 Folder-2 MP3-1 MP3-2

Press PLAY.

To resume normal playback

Select Repeat : “Off” in step 2.

Notes:

• The program is canceled when you eject the disc or turn the power off.

• In case of Audio CD, the function of A-B Repeat can be used. See “A-B Repeat playback”

• Track repeat function is canceled whenever SKIP

The unit automatically starts repeat playback after finishing the current track.

is pressed.

Select Files Repeat :Off Mode :Off

Select Files

Repeat :Track Mode :Off

To resume normal playback

Select Mode : “Off” in step 2.

▲ /▼ / / ENTER

PLAY SKIP /

Random playback (CD)

In the file browser, press “Mode” during stop mode.

Press ENTER to select “Random”.

Press PLAY.

/ or / to select

Folder-1 Folder-2 MP3-1 MP3-2

The Random playback will start.

Select Files Repeat :Off Mode :Off

Select Files Repeat :Off Mode :Random

Program playback (CD)

In the file browser, press / or / to select “Edit Mode”, then press ENTER.

Folder-1

Repeat :Off

Folder-2

Mode :Off

MP3-1 MP3-2

When “Edit Mode” is black color, you can mark the files which you want to add into Program list.

/ or / to select file you want to

Press add into the program list.

Press / or / to select “Add To Program”. Then press ENTER. All marked files are added

into the program list.

Folder-1 Folder-2

MP3-1

MP3-2 MP3-3 WMA-1

Press ENTER. Selected file was marked. Repeat this procedure to select the other files.

Folder-1 Folder-2 MP3-1 MP3-2 MP3-3 WMA-1

•When you finish store all files which you want into the Program list, select “Edit Mode” and press ENTER to release edit mode.

Edit Mode

Repeat :Off Mode :Off

Edit Mode

JPEG Previe

Edit Mode

Program View

Add To Program

JPEG Preview

▲ /▼ / / ENTER

PLAY

Press

/ or /

then press ENTER. Program View shows only the

programed files that you have added in step 2.

to select “Program View”,

MP3-1 MP3-2 MP3-3 WMA-3

Program View

Folder-1 Folder-2 MP3-1 MP3-2 MP3-3 WMA-1 WMA-2

Browser View

In the Program View, press PLAY. The files start to playback in programmed order that

were added by you.

To remove file from program list

In the Edit Mode, switch to Program View. Select file you want to remove, then press ENTER. Select “Clear Program” and press ENTER. Marked file is removed from program list.

WMA-3

Edit Mode

Browser View

Clear Program

JPEG Preview

Edit Mode

Program View

Add To Program

JPEG Preview

Advanced playback

Function setup

Customizing the function settings

You can change the default settings of the DVD mode to customize performance to your preference.

DVD VCD

Setting procedure

Press SETUP during stop mode.

The following on-screen display appears.

Press ▲or ▼ to select the desired section, then

press

First option will be highlighted. Press to select the desired option.

Then press or ENTER. The selectable settings will appear.

Parental : Off

DRC : Off

E.B.L. : Off

Menu : English Set Password

QSound : On

TV Screen : 4:3

Subtitle : English Output : Interlace

Display : On

Audio : English DivX(R) VOD

Picture Mode : Auto JPEG Interval : 5 Seconds Screen Saver : On

Parental : Off

DRC : Off

Menu : English

TV Screen : 4:3 Set Password

QSound : On

Subtitle : English

Display : On Output : Interlace

Audio : English

Picture Mode : Auto DivX(R) VOD

JPEG Interval : Off

▲ or ▼

Parental : Off

DRC : Off

Menu : English

TV Screen : 4:3

Set Password

QSound : On

Subtitle : English

Display : On Output : Interlace

Audio : English

Picture Mode : Auto DivX(R) VOD

JPEG Interval : Off

Parental : Off

DRC : Off

Menu : English

TV Screen 4:3

Set Password

QSound : On

Subtitle : English

Display 4:3 Output : Interlace

Audio : English

Picture Mode : Auto DivX(R) VOD

JPEG Interval : Off

SETUP ENTER ▲ /▼ / RETURN

Change the selection using ▲ or ▼ , by referring to the corresponding pages

Press ENTER to save the setting.

To clear SETUP screen, press SETUP or RETURN.

~ 51.

• Repeat steps 3 and 5 to change

other option.

• To select another section, go

back to step 2 by pressing repeatedly.

Setting details

Section

Option

Menu Subtitle Audio

TV Screen

Display

Picture Mode

JPEG Interval

DRC

Parental

Password

DivX(R) VOD

Details

To select the language of “Menu”, “Subtitle” and “Audio” if more than one language are available on the disc.

To select a picture size according to the aspect ratio of your TV.

To turn On or Off the operational status display on the screen.

To select a preferred picture mode from “Video”, “Film” or “Auto”.

To select a preferred setting for the slide show playback.

To select On or Off for DRC (Dynamic Range Control).

To select a preferred parental level for the parental setting.

Input 4-digit password to set the parental level.

To display your 8-character registration code.

Page

Function setup

Customizing the function settings (Continued)

Setting details

Parental : Off

DRC : Off

E.B.L. : Off

Menu : English Set Password

QSound : On

TV Screen : 4:3

Subtitle : English Output : Interlace

Display : On

Audio : English DivX(R) VOD

Picture Mode : Auto JPEG Interval : 5 Seconds Screen Saver : On

Menu, Subtitle, Audio

You can select the language of “Menu”, “Subtitle” and “Audio” if more than one languages are recorded onto the disc.

English, Francais, Espanol:

The selected language will be heard or seen.

Other:

Other language can be selected (see “Language

code list”

Original (Audio):

The unit will select the first priority language of each disc.

Off (Subtitle):

Subtitles do not appear.

Notes:

• If the selected language is not recorded on the disc, the first-priority language is selected.

• If you want to change the OSD language, you can perform it by TV SETUP MENU

TV Screen

You have the following screen sizes to choose from:

4:3

(Letter box):

Select this mode when connecting to a conventional TV. When playing back a wide screen-DVD disc, it displays the wide picture with black bands at the top and bottom of screen.

(Pan & scan):

4:3

It displays the wide picture on the whole screen with left and right edges automatically cut off.

Note:

If the DVD disc is not formatted in the Pan & scan style, it will display 4:3 style.

Display

On screen display can be switched on or off when you press any buttons.

On: On screen displays appear when you press

the buttons (factory setting).

Off: On screen displays do not appear when you

press any buttons.

Parental : Off

DRC : Off

Menu : English

TV Screen : 4:3 Set Password

QSound : On

Subtitle : English

Display : On Output : Interlace

Audio : English

Picture Mode : Auto DivX(R) VOD

JPEG Interval : Off

Picture Mode

There are two types of source content in pictures recorded in DVD video discs: film content (pictures recorded from films at 24 frames per second) and video content (video signals recorded at 30 frames per second). Make this selection according to the type of content being viewed.

Auto: Select this position normally.

The DVD player automatically detects source content, film or video of playback source, and converts that signal in the progressive output format in an appropriate method.

Film: The DVD player converts film content

pictures in the progressive output format appropriately. Suitable for playback of film content pictures. The progressive output feature will be most effective under this selection.

Video: The DVD player filters video signal and

converts it in the progressive output format appropriately. Suitable for playback of video content pictures.

Note:

Depending on the disc, pictures may be cut off or doubled. In this case, select “Video”.

JPEG Interval

You can continuously playback all JPEG files automatically. After the selection below, the disc will start playback on which JPEG files have been recorded.

Off:

Plays back one file at a time.

5 Seconds:

Plays back images in the form of a slide show at 5 second intervals.

10 Seconds:

Plays back images in the form of a slide show at 10 second intervals.

15 Seconds:

Plays back images in the form of a slide show at 15 second intervals.

Function setup

Customizing the function settings (Continued)

Setting details

Parental : Off

E.B.L. : Off

DRC : Off DRC : Off Set Password

TV Screen : 4:3 Output : Interlace

Display : On DivX(R) VOD

Picture Mode : Auto JPEG Interval : 5 Seconds Screen Saver : On

DRC

DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment.

Off:

It plays back at the recording level on the disc.

On:

Loud sound such as explosion is toned down slightly when played back. This is suitable when it is connected to a stereo.

Notes:

• This function works only during playback of Dolby Digital

recorded discs.

• The level of Dynamic Range Reduction may differ

depending on DVD video disc.

Parental control setting

Some discs are specified as not suitable for children. Such discs can be limited not to playback with the unit.

1) Press

or to select “Parental”, then press

ENTER. “Enter Password” screen will appear.

2) Press “0000” using Number buttons (0–9). (Please note, this is pre-setting password of this unit). Then press ENTER. The parental level list will appear.

• Level Off: The parental control setting does not

• Level 8: All DVD software can be played

• Level 1: DVD software for adults cannot be

3) Press

or to select from the level 1 to level 8.

The limitation will be more severe as the level number is lower. Then press ENTER.

Notes:

• Depending on the discs, the unit cannot limit playback.

• Some discs may not be encoded with specific rating

level information though its disc jacket says “adult.” For those discs, the age restriction will not work.

• The password is required every time when you

change the parental level.

• If you input a wrong number, press CANCEL.

function. back. played back.

Menu : English

E.B.L. : Off

Parental : Off QSound : On

Subtitle : English

TV Screen : 4:3

Password : Change Audio : English

Display : On

DivX(R) VOD : Display Picture Mode : Auto JPEG Interval : 5 Seconds Screen Saver : On

■ Set the new password

1) Press

or to select “Password”, then press

ENTER. “Enter Current Password” screen will appear.

2) Press Number buttons (0–9) to input the current password (If the password has not been set yet after you purchase this unit, it is “0000”).

3) Then press ENTER. “Enter New Password” screen will appear. Press Number buttons (0–9) to input the new password.

4) Press ENTER. Now your new password has been set. Be sure to remember this number!

If you forget the password.

1) Press EJECT to remove the disc.

2) While holding 7 down on the remote control and then press STOP on the front panel. “Password Clear” appears on the screen. Now the password has been returned to the initial value (“0000”).

DivX

VOD

In order to play DivX content on this unit, you first need to register the unit with your DivX generating a DivX submit to your provider.

Press or to select “DivX(R) VOD”. Then press ENTER. Your 8-character registration code is displayed. Make a note of the code as you will need it when you register with a DivX Then press ENTER to select Done.

Note: If each setup (pages can always work under the same condition (especially with DVD discs). Each setup will be retained in the memory even if you turn the power off.

VOD (Video On Demand)

VOD content provider. You do this by

VOD registration code, which you

VOD provider.

~ 51) has completed, the unit

Function setup

Others

Temporary cancel the rating level by DVD disc

Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set. It is up to you to decide whether to cancel the rating level or not.

DVD

Temporary cancel the rating level by DVD disc

Load a DVD disc.

If the DVD disc has been designed to temporarily cancel the Rating level, the screen

which follows the “Reading” screen will change, depending on which disc is played. If you select “YES” with the ENTER key, password input screen will then appear.

• If “NO” is selected, press EJECT to remove the disc.

Enter the password with Number buttons (0–9). Then press ENTER.

To exit from the entry, press RETURN.

Enter Password

Playback will commence if the entered password is correct.

Note:

This temporary cancellation of rating level will be kept until the disc is ejected. When the disc is ejected, the original rating level will be set again automatically.

0–9

ENTER RETURN

Language code list

Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” 48.

Language Name Code Language Name Code Language Name Code Language Name Code Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919 Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921 Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922 Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925 Amharic 1123 Galician 1722 Malay 2329 Spanish 1529 Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931 Armenian 1835 German 1415 Maltese 2330 Swahili 2933 Assamese 1129 Greek 1522 Maori 2319 Swedish 2932 Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022 Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017 Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011 Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030 Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015 Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018 Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225 Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019 Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025 Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028 Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021 Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033 Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121 Chinese 3618 Javanese 2033

Rhaeto-Romance

2823 Urdu 3128 Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136 Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219 Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225 Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335 Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325 English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418 Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019 Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525 Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631

Others

Troubleshooting

Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer or service outlet if problems persist. Be sure all connections are properly made when using with other units.

SYMPTOMS POSSIBLE SOLUTIONS

POWER

TV/DVD does not operate.

TV BROADCAST RECEPTION

Poor sound or No sound.

Poor picture or No picture.

Poor reception on some channels.

Poor color or no color.

Picture wobbles or drifts.

No CATV reception.

Horizontal or diagonal bars on screen.

No reception above channel 13.

TV shuts off.

Closed - Caption is not activated.

Display is not shown in your language.

• Make sure the connection of the AC adapter and AC cord.

• Try another AC outlet.

• Unplug unit, then plug it back in.

• Station or Cable TV may have problems, try another station.

• Check Volume adjustments.

• Check for sources of possible interference.

• Station or Cable TV may have problems, try another station.

• Check antenna or Cable TV connections, reorient antenna.

• Check for sources of possible interference.

• Check picture control adjustments.

• Station or Cable TV may have problems, try another station.

• Station signal is weak, reorient antenna to receive weaker station.

• Check for sources of possible interference.

• Station or Cable TV may have problems, try another station.

• Make sure channels are set into memory.

• Check picture control adjustments.

• Check antenna or Cable TV connections, reorient antenna.

• Check for sources of possible interference.

• Station or Cable TV may have problems, try another station.

• Make sure channels are set into memory.

• Cable TV company is scrambling signal.

• Check antenna or Cable TV connections, reorient antenna.

• Check all Cable TV connections.

• Set TV/CABLE selection to the CABLE position.

• Station or Cable TV system problems, try another station.

• Check antenna or Cable TV connections, reorient antenna.

• Check for sources of possible interference.

• Make sure TV/CABLE selection is in the appropriate position.

• If using antenna, check UHF antenna connections.

• No broadcast on station tuned.

• Auto power off feature worked.

• Sleep Timer is set.

• Power interrupted.

• TV station experiencing problems or program tuned is not closed captioned. Try another channel.

• Check Cable TV connection or VHF/UHF antenna, reposition or rotate antenna.

• Press CLOSED CAPTION button to turn on the closed caption decoder.

• Select proper language in the menu options.

PAGE

23 23 56

14,15

56 28

23 14 56

23 22 28

14,15

56 23

14,15

15 22 23

14,15

56 22

14 22

23 24

14,15

SYMPTOMS POSSIBLE SOLUTIONS PAGE

DVD

Playback doesn’t start.

No picture. • TV/DVD selector is not set correctly.

No sound.

Picture is distorted during fast reverse/forward playback.

Stopping playback, search, slowmotion play, repeat play, or program play, etc. cannot be performed.

No on-screen display. • Set Display to On. The unit or remote operation key

is not functioning. Playback does not start when the

title is selected. Audio soundtrack and/or subtitle

–

language is not changed when you playback a DVD.

No subtitle.

Angle cannot be changed. • Multi-angles are not recorded on the DVD disc. “✕” appears on the screen.

REMOTE CONTROL

The remote control does not function.

• No disc is loaded.

• The disc may be dirty. Clean up the disc.

• The unit cannot play CD-ROMs, etc.

• Check the input selector of the amplifier is set properly.

• The unit is in the special playback mode.

• Select the correct Audio Input/Output position on AV amplifier.

• The picture will be distorted occasionally.

• Some discs may not do some of the functions.

• Turn off the unit and unplug the AC power cord for several minutes, then replug it.

• Check the RATING LEVEL setup.

• Multilingual language is not recorded on the DVD disc.

• Some discs have no subtitles.

• Subtitles are cleared. Press the SUBTITLE button.

• The function is prohibited with the unit or the disc.

• Aim the remote control at the remote sensor.

• Operate within approx. 5 meters or reduce the light in the room.

• Clear the path of the beam.

• The batteries are weak. Replace the batteries.

• Check the batteries are inserted correctly.

7 8

– 33 18

–

Others

38 37

Others

Reception disturbances

Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF antenna. Outdoor antennas are recommended for best results. The most common types of television interference are shown below. If one of these symptoms appear when the TV/DVD is connected to a Cable TV system, the disturbance may be caused by the local Cable TV company broadcast.

IGNITION

Black spots or horizontal streaks may appear, the picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps or AC powered tools and appliances such as drills or hair dryers.

GHOSTS

Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected by tall buildings, hills or other large objects. Changing the direction or position of the antenna may improve the reception.

SNOW

If the TV/DVD is located far from the TV station, in a fringe reception area where the signal is weak, small dots may appear in the picture. If the signal is extremely weak, the installation of a larger external antenna may be necessary.

RADIO FREQUENCY INTERFERENCE (RFI)

Caused by two-way radios, this type of interference produces moving ripples or diagonal streaks in the picture. Some cases may cause a loss of contrast in the picture. Changing the direction and position of the antenna or installing an RFI filter may improve the picture.

CARE AND MAINTENANCE

To prevent fire or shock hazard, disconnect the TV/DVD from the power source before cleaning. Use caution when cleaning or wiping the plastic parts.

Specifications

General

Power supply AC 120V 60Hz (with supplied AC adapter) Power consumption Operation: 50 W, Stand by: 1 W (with supplied AC adapter) Weight 13.2 lbs (6.0 kg) Dimensions Width: 18-3/4 inches (476 mm)

Operating temperature 5˚C-40˚C (41˚F-104˚F) Operating humidity Less than 80% RH (No condensation)

Television

LCD panel 15-inch diagonal (Screen size is approximate.) Display method Color TFT LCD Number of pixels 1024 (Horizontal) x 768 (Vertical) Tuner type F-Synth Receiving channels VHF: 2-13

Antenna input VHF/UHF 75 Ω Speaker 1-1/2 x 2-11/16 inches (38.1 x 68.6 mm), 8 Ω x 2 Audio output power 1.5W + 1.5W

DVD/CD Player

Signal system NTSC Applicable disc 1. DVD (12cm, 8cm)

Pickup 1-Lens, 2-Beams System

Input/Output

S-Video input (Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1

Component video input (Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1

Video input 1.0 V (p-p), 75 Ω, negative sync., pin jack x 2 Audio input –8dBm, 50 kΩ, negative sync., pin jack (L/R) x 2 Digital audio output (Coaxial) 0.5 V (p-p), 75 Ω, pin jack x 1 Headphone ø3.5mm stereo mini jack x 1

Accessories

Remote control (DC-LB1) ................................................ 1

Batteries (R03/AAA) ........................................................ 2

AC adapter ...................................................................... 1

AC cord (for AC adapter) ................................................. 1

300-75 Ω matching transformer....................................... 1

Owner’s manual (this booklet) ......................................... 1

• This model complies with the above specifications.

• Designs and specifications are subject to change without notice.

• This model may not be compatible with features and/or specifications that may be added in the future.

Height: 13-15/16 inches (353.5 mm) Depth: 9-1/16 inches (230 mm)

UHF: 14-69 CATV: 1-125 (4A, A5~A1, A~I, J~W, W+1~W+84)

2. CD (12cm, 8cm)

(PB, PR) 0.7V (p-p), 75 Ω, pin jack x 2

Others

Limited United States Warranty LCD TV/DVD Combination - Depot Repair Warranty

Toshiba America Consumer Products, L.L.C. ("TACP") makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD TV/DVD COMBINATION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.

LCD TV/DVD COMBINATIONS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.

LCD TV/DVD COMBINATIONS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.

Limited One (1) Year Warranty on Parts and Labor

TACP warrants this LCD TV/DVD Combination and its parts against defects in materials or workmanship for a period of one (1) year after the date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP'S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU.

Rental Units

The warranty for LCD TV/DVD Combination rental units begins on the date of the first rental or thirty (30) days after the date of shipment to the rental firm, whichever comes first.

Commercial Units

LCD TV/DVD Combinations sold and used for commercial purposes have a limited warranty for all parts and labor, which warranty begins on the date of original retail purchase and ends on the date that is ninety (90) days thereafter.

Owner's Manual and Product Registration Card

Read this owner’s manual thoroughly before operating this LCD TV/DVD Combination.

Complete and mail the enclosed product registration card or register your LCD TV/DVD Combination online at

www.tacp.toshiba.com/service as soon as possible. By registering your LCD TV/DVD Combination you will enable TACP to bring you new products specifically designed to meet your needs and help us to contact you in the unlikely event a safety notification is required under the U.S. Consumer Product Safety Act. Failure to complete and return the product registration card does not diminish your warranty rights.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING CONDITIONS:

(1) You must retain your bill of sale or provide

other proof of purchase.

(2) All warranty servicing of this LCD TV/DVD

Combination must be made by the Depot Warranty Repair Center specified by the TACP Consumer Solutions Center.

(3) The warranties from TACP are effective only if

the LCD TV/DVD Combination is purchased and operated in the Continental U.S.A. or Puerto Rico.

(4) Labor service charges for set installation,

setup, adjustment of customer controls, and installation or repair of antenna systems are not covered by this warranty. Reception problems caused by inadequate antenna systems are your responsibility.

(5) Warranties extend only to defects in materials

or workmanship as limited above, and do not extend to any LCD TV/DVD Combination or parts that have been lost or discarded by you or to damage to the LCD TV/DVD Combination or parts caused by fires, misuse, accident, Acts of God (such as lightning or fluctuations in electric power), improper installation, improper maintenance, or use in violation of instructions furnished by TACP; use or malfunction through simultaneous use of this LCD TV/DVD Combination and connected equipment; or to units that have been modified or had the serial number removed, altered, defaced, or rendered illegible.

How to Obtain Warranty Services

If, after following all of the operating instructions in this manual and checking the section "Troubleshooting," you find that service is needed:

(1) For instructions on how to obtain warranty

service for your LCD TV/DVD Combination, contact TACP's Consumer Solution Center toll free at 1-800-631-3811.

(2) You must include a copy or original bill of sale

or other proof of purchase along with the entire LCD TV/DVD Combination to the Depot Warranty Repair Center specified by the TACP Consumer Solutions Center. You are responsible for all inbound transportation and insurance charges for the LCD TV/DVD Combination to the Depot Warranty Repair Center specified by the TACP Consumer Solutions Center.

For additional information, visit TACP's website: www.tacp.toshiba.com

ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A., INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A. AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR INABILITY TO USE THIS LCD TV/DVD COMBINATION).

No person, agent, distributor, dealer, or company is authorized to change, modify, or extend the terms of these warranties in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP arising under the warranty or under any statute or law of the United States or any state thereof is hereby limited to ninety (90) days from the date you discover, or should have discovered, the defect. This limitation does not apply to implied warranties arising under state law.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, WHEN AN ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE PROVISIONS MAY NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES.

Others

CAUTION

THIS

LCD COLOR TELEVISION

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MA Y RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIA TION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT ST ARE INTO BEAM.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

EMPLOYS A LASER SYSTEM.

CERTIFICATION: COMPLIES WITH FDA RADIA TION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

PREPARATION OF SERVICING

The laser diode used for a pickup head may be destroyed with external static electricity. Moreover, even if it is operating normally after repair, when static electricity discharge is received at the time of repair, the life of the product may be shortened. Please perform the following measure against static electricity, be careful of destruction of a laser diode at the time of repair.

• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat.

• Soldering iron with ground wire or ceramic type is used.

• A worker needs to use a ground conductive wrist strap for body.

A1-1

IMPORTANT SERVICE SAFETY INFORMATION

Safety precautions to be followed during servicing:

Parts marked with an list.

Before returning the DVD product to the customer, make the appropriate leakage current check or resistance measurements to ensure that exposed parts are properly insulated from the supply circuit.

A leakage current check is recommended for this unit. Plug the AC line cord directly into a 120V 60Hz AC outlet (do not use an isolation transformer for this check). Use a leakage current tester (Fig. 1) or a metering system which complies with Underwriters Laboratories (UL 1492P). Measure for current from all exposed metal parts of the cabinet to a known earth ground: particularly, any exposed metal part having a return path to the chassis. Any current measured must not exceed 0.5mA. Any measurement not within the limits outlined above are indicative of a potential shock hazard and corrective action must be taken before returning the unit to the customer.

are critical parts for safety. Replace only with the one described in the parts

(Reading should not be above 0.5mA) Leakage Current Tester

PRODUCT UNDER TEST

1.5K ohm

0.15 µF

2-Blade polarized type cord set

Test all exposed metal surfaces

TEST PROBE

Fig. 1 AC Leakage Test

KNOWN EARTH GROUND

A1-2

IMPORTANT SAFEGUARDS

READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

ATTACHMENTS

Do not use attachments not recommended by the unit’s manufacturer as they may cause hazards.

WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer.

8A.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

VENTILATION

Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10.

POWER SOURCES

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company . For units intended to operate from battery power, or other sources, refer to the operating instructions.

11.

GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way . This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If your unit is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin, this plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

12.

POWER-CORD PROTECTION

13.

LIGHTNING

14.

POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15.

OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16.

OBJECT AND LIQUID ENTRY

PORT ABLE CART WARNING

(symbol provided by RETAC)

S3126A

A1-3

IMPORTANT SAFEGUARDS (CONTINUED)

OUTDOOR ANTENNA GROUNDING

17.

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

SERVICING

18.

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

DAMAGE REQUIRING SERVICE

19.

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

When the power-supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen into the unit.

If the unit has been exposed to rain or water.

If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

If the unit has been dropped or the cabinet has been damaged.

When the unit exhibits a distinct change in performance, this indicates a need for service.

REPLACEMENT PARTS

20.

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards.

SAFETY CHECK

21.

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

WALL OR CEILING MOUNTING

22.

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

HEAT

23.

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

DISC TRAY

24.

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

CONNECTING

25.

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

SOUND VOLUME

26.

Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume sound may cause hearing or speaker damage.

SOUND DISTORTION

27.

Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.

HEADPHONES

28.

When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

LASER BEAM

29.

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

DISC

30.

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

NOTE TO CATV SYSTEM INSTALLER

31.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

A1-4

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

ELECTRIC SERVICE

EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

S2898A

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

A1-5

WHEN REPLACING DVD DECK

[ When removing the DVD Deck ]

Before removing Pick Up PCB and DVD PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged.

[ When installing the DVD Deck ]

Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector.

NOTE

Before your operation, please read “PREPARATION OF SERVICING”.

• Use the Lead Free solder.

• Manual soldering conditions

•

• Soldering temperature: 350 ± 5˚C

• Soldering time: Within 2 seconds

• Soldering combination: Sn-3.0Ag-0.5Cu When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to keep the

• Flux smoke away from it.

Pick Up PCB

Fig. 1

Short circuit using a soldering iron.

A1-6

DISC REMOVAL METHOD AT NO POWER SUPPLY

Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)

Slide the Belt Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1)

Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc.

DVD Deck

Belt Loading

Fig. 1

PARENTAL CONTROL - RATING LEVEL

4 DIGIT PASSWORD CANCELLATION

If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below.

Turn Unit ON.

1. Set the DVD to the Stop Mode.

2. Check that ‘No disc’ is displayed on the screen.

3. Press and hold the ‘STOP’ button on the front panel.

4. Simultaneously press and hold the ‘7’ key on the remote control unit.

5. Hold both keys for more than 2 seconds.

6. The On Screen Display message ‘PASSWORD CLEAR’ will appear.

7. The 4 digit password has now been cleared.

TRAY LOCK

The disk cannot be taken out by setting the Tray Lock, please follow the steps below.

Turn Unit ON.

1. Set the DVD to the Stop Mode.

2. Press it in order of ‘SETUP’, ‘SUBTITLE’, ‘3’, ‘AUDIO’ and ‘0’ key of a remote control unit.

3. The On Screen Display message ‘ ‘ will appear.

4. The Tray Lock has now been set up.

To unlock the Tray Lock, please follow the steps below.

Turn Unit ON.

1. Set the DVD to the Stop Mode.

2. Press it in order of ‘SETUP’, ‘SUBTITLE’, ‘3’, ‘AUDIO’ and ‘0’ key of a remote control unit.

3. The On Screen Display message ‘ ‘ will appear.

4. The Tray Lock has now been cleared.

A1-7

TABLE OF CONTENTS

• GREEN PRODUCT PROCUREMENT

• LEAD-FREE SOLDER

• OWNER'S MANUAL

CAUTION.....................................................................................................................

IMPORTANT SERVICE SAFETY INFORMATION .....................................................

IMPORTANT SAFEGUARDS .....................................................................................

WHEN REPLACING DVD DECK ................................................................................

DISC REMOVAL METHOD AT NO POWER SUPPLY...............................................

PARENTAL CONTROL - RATING LEVEL .................................................................

TRAY LOCK ................................................................................................................

TABLE OF CONTENTS ..............................................................................................

GENERAL SPECIFICATIONS ....................................................................................

DISASSEMBLY INSTRUCTIONS

1.REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS ................................

2.REMOVAL OF DVD DECK PARTS ......................................................................

3.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ..................................

SERVICE MODE LIST.................................................................................................

SERVICING FIXTURES AND TOOLS ........................................................................

RE-WRITE FOR DVD FIRMWARE .............................................................................

CONFIRMATION OF CHECK SUM ............................................................................

WHEN REPLACING EEPROM (MEMORY) IC ...........................................................

ELECTRICAL ADJUSTMENTS ..................................................................................

TROUBLESHOOTING GUIDE ....................................................................................

BLOCK DIAGRAMS

DVD..........................................................................................................................

TV.............................................................................................................................

POWER....................................................................................................................

PRINTED CIRCUIT BOARDS

SCALER ...................................................................................................................

AV/OPERATION1/REMOCON/SIDE JACK.............................................................

DVD/OPERATION2 .................................................................................................

BACK LIGHT/SW .....................................................................................................

SCHEMATIC DIAGRAMS

JACK ........................................................................................................................

TUNER/STEREO

AV SWITCH .............................................................................................................

SOUND ....................................................................................................................

POWER....................................................................................................................

OPERATION/SIDE JACK/REMOCON.....................................................................

MICON .....................................................................................................................

SCALER ...................................................................................................................

LVDS........................................................................................................................

SYNC SEPA.............................................................................................................

REGULATOR...........................................................................................................

MPEG/MICON/DSP/RF_AMP..................................................................................

MEMORY .................................................................................................................

AUDIO/VIDEO..........................................................................................................

MOTOR DRIVE ........................................................................................................

REGULATOR2.........................................................................................................

OPERATION2 ..........................................................................................................

INVERTER ...............................................................................................................

SW ...........................................................................................................................

INTERCONNECTION DIAGRAM ................................................................................

WAVEFORMS .............................................................................................................

MECHANICAL EXPLODED VIEWS ...........................................................................

DVD DECK EXPLODED VIEW ...................................................................................

MECHANICAL REPLACEMENT PARTS LIST ..........................................................

DVD DECK REPLACEMENT PARTS LIST ................................................................

ELECTRICAL REPLACEMENT PARTS LIST ............................................................

A1-1 A1-2 A1-3~A1-5 A1-6 A1-7 A1-7 A1-7 A2-1 A3-1~A3-5

B1-1~B1-4 B2-1~B2-3 B3-1, B3-2 C-1 C-2 C-2 C-3 C-3 D-1~D-4 E-1~E-11

F-1, F-2 F-3, F-4 F-5, F-6

G-1, G-2 G-3~G-6 G-7, G-8 G-9, G-10

H-1, H-2 H-3, H-4 H-5, H-6 H-7, H-8 H-9, H-10 H-11, H-12 H-13, H-14 H-15, H-16 H-17, H-18 H-19, H-20 H-21, H-22 H-23, H-24 H-25, H-26 H-27, H-28 H-29, H-30 H-31, H-32 H-33, H-34 H-35, H-36 H-37, H-38 H-39, H-40 I-1~I-4 J1-1~J1-3 J2-1 K1-1, K1-2 K2-1 K3-1~K3-5

A2-1

GENERAL SPECIFICATIONS

G-1 TV LCD LCD Size / Visual Size 15.0 inch / 380.0mmV

System LCD Type Color TFT LCD

Color System NTSC Speaker 2 Speaker

Sound Output Max 1.5W + 1.5W

G-2 DVD System Color System NTSC

Disc

Disc Diameter 120 mm , 80 mm Drive DSM-2 Search speed Fwd 4 step

Slow speed Fwd 1/7 -1/2 times

G-3 Tuning Broadcasting System US System M

System Tuner and System 1Tuner

Receive CH Destination US(W/CABLE)

Intermediate Picture(FP) 45.75MHz Frequency Sound(FS) 41.25MHz

Preset CH No Stereo/Dual TV Sound US-Stereo Tuner Sound Muting Yes

G-4 Signal Video Signal Input Level 1 V p-p/75 ohm

RGB Signal Output Level -Audio Signal Input Level -8.0dBm/50k ohm

G-5 Power Power Source AC 120V, 60Hz

Power Consumption at AC Adapter 50W at 120V 60Hz

Protector Power Fuse Yes

G-6 Regulation Safety UL/CSA

G-7 Temperature Operation +5oC ~ +40oC

G-8 Operating Humidity Less than 80% RH

Number of Pixels 1024(H) x 768(V)

View Range Left/Right 70/70 degree

Up/Down 60/65 degree

Position Front Size 1.5 x 2.7 inch Impedance 8 ohm

10%(Typical) ---

DVD, CD-DA, CD-R/RW, Video CD DVD-R/RW (Video Format Only)

Actual 2-45 times (DVD)

4-40 times (CD)

Rev 4 step

Actual 2-45 times (DVD)

4-40 times (CD)

Actual --

Rev 1/7 -1/2 times

Actual --

CH Coverage 2~69, 4A, A-5~A-1, A~I, J~W, W+1~W+84

FP-FS 4.50MHz

Output Level -S/N Ratio (Weighted) -Horizontal Resolution at DVD Mode --

Output Level -Digital Output Level 0.5 V p-p/75 ohm S/N Ratio at DVD (Weighted) -Harmonic Distortion -Frequency Response : at DVD --

at Video CD --

at SVCD --

at CD --

DC --

at DC -Stand by (at AC Adapter) 1W at 120V 60Hz Energy Star Yes Per Year -- kWh/Year

Safety Circuit Yes IC Protector(Micro Fuse) Yes

Radiation FCC/IC Laser DHHS

Storage -20oC ~ +60oC

A3-1

GENERAL SPECIFICATIONS

G-9 Clock and Clock No

Timer Sleep Timer Max Time 120 Min

On Timer Program No Off Timer Program No Wake Up Timer No Timer Back-up (at Power Off Mode) more than -- Min Sec

G-10 Remote Unit RC-LB

Control Glow in Dark Remocon Yes

Remocon Format ORION Format NEC Custom Code 71-8E h Power Source Voltage(D.C) 3V

Total Keys 47 Key Keys Power Yes

Step 10 Min

UM size x pcs UM-4 x 2 pcs

1 Yes 2 Yes 3 Yes 4 Yes 5 Yes 6 Yes 7 Yes 8 Yes 9 Yes 0 Yes Play Yes Stop Yes Search+ Yes Search- Yes Skip+ Yes Skip- Yes Slow+ Yes Slow- Yes Pause/Still/Step Yes Recall Yes TV/DVD Yes Cancel Yes Audio Select Yes Angle Yes Subtitle Yes Top Menu Yes Setup/ Menu Yes DVD Menu Yes Return Yes Up / CH Up Yes Down / CH Down Yes Vol Down Yes Vol Up Yes Left Yes Right Yes Enter Yes Play Mode Yes Closed Caption Yes Input Select Yes Repeat A-B Yes Zoom/ Quick View Yes Mute Yes Eject Yes Sleep Yes Jump Yes Game Yes Freeze frame No

A3-2

GENERAL SPECIFICATIONS

G-11 Features Auto Shut Off Yes

(TV) Auto Search No

Power On Memory No Comb Filter Yes

Game Position Yes Auto Setup(Language/CH Program) No Picture Setting Yes

Picture Preference Yes Brightness , Contrast , Color Yes Tint Yes Sharpness Yes Color Temperature Yes Cable Clear No

Audio MTS Yes

Tone Control (Bass/Treble/Balance) Yes Stable Sound No Surround Yes BBE No SRS WOW (SRS 3D/Focus/Tru Bass) No Valiable Audio Out No

Tuning CH Program Yes

TV/Cable Yes ADD/DELETE Yes

Label CH Label No

Video Label No

Favorite CH No V-Chip Yes

Type USA Type

RRT Setup Lock Hotel Lock No

Channel Lock No Video Lock No Panel Lock No

OSD Language Closed Caption CC Advanced Picture Size Picture Scroll Cinema Mode No Aspect Backlight No PFC(Power Factor circuit) Freeze frame No PIP/POP No Direct Input Selection No Game Position Yes PC Monitor Input No HDMI Input No Component Input Yes

720x480i (4:3) Yes (60Hz) 720x480i (16:9) Yes (60Hz) 720x480p (4:3) Yes (60Hz) 720x480p (16:9) Yes (60Hz) 720x576i (4:3) No 720x576i (16:9) No 720x576p (4:3) No 720x576p (16:9) No 1280x720p No 1920x1080i No

English French Spanish Yes

No No No

A3-3

GENERAL SPECIFICATIONS

Features Tray Lock Yes (DVD) WMA Yes

G-12 Accessories Owner's Manual Language English/French

JPEG Yes Video CD Playback Yes SVCD Playback

Overlay Graphics And Text No Command List No Entry Point Jump No

MP3 Playback Yes Divx Playback Yes

DMF Support No

Digital Out (Dolby Digital) Yes

(MPEG) Yes (PCM) Yes (DTS) Yes

Down Mix Out (Dolby Digital) Yes

(DTS) No

3D Surround No Closed Caption Yes Screen Saver No Audio DAC 192kHz / 24bit

w/Guarantee Card Yes

Remote Control Unit Yes Rod Antenna

Poles -Terminal --

Loop Antenna

Terminal --

U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet Quick Set-up Sheet Battery Yes

UM size x pcs UM-4 x 2 pcs OEM Brand No

AC Adapter Yes AC Cord (for AC Adapter) Yes AV Cord (2Pin-1Pin) Registration Card Yes 300 ohm to 75 ohm Antenna Adapter Yes Sheet Information (Return) Yes(USA version, Canada version)

No No No No No No No No No No

A3-4

GENERAL SPECIFICATIONS

G-13 Interface Switch Top Power (Tact) Yes

Rear Main Power SW No

Indicator Power/Stand-By Yes (Green / Red)

Terminals Rear Video Input 1 RCA x 1

Side Video Input 2 RCA x 1

G-14 Set Size Approx. W x D x H (mm) 476 x 230 x 353.5

G-15 Weight Net (Approx.) 6.0kg (13.2 lbs)

G-16 Carton Master Carton No

Gift Box Material Single/Brown

Drop Test

Container Stuffing (40' container) 740

G-17 Material Cabinet Front PS 94V0 DECABROM

PCB Non-Halogen Demand No

G-18 Environment Environmental standard requirement (by buyer) Green procurement of TOSHIBA

G-19 AC Power Adapter Provided Accessories

Power Requirement AC 120V 60Hz Max Power Consumption (Adapter Only) at AC 65 W DC Output DC Jack : DC12V 4.5A Dimension Approx. W x D x H (mm) 150 x 72 x 43 Weight Approx. 450g

Channel Up Yes Channel Down Yes Volume Up Yes Volume Down Yes Play Yes Eject Yes Skip+, Search+ Yes Skip-, Search- Yes Still/Pause No Stop Yes Main Power SW No Input Select No

On Timer No

Audio Input 1 RCA x 2 (L/MONO, R) S- Input 1 No Video Output No Audio Output No Component Yes Euro Scart(21Pin) No PC Monitor Input No Digital Audio Output Coaxial (DVD Only) DC Jack (Center +) VHF/UHF Antenna Input AC Outlet No

Audio Input 2 RCA x 2 (L/MONO, R) S- Input 2 Yes Other Terminal Headphone

w/o Handle, Stand Approx. W x D x H (mm)

Net w/o Handle, Stand (Approx.) 4.5kg (9.9 lbs) Gross (Approx.) 8.0kg (17.6 lbs)

Content --- Sets Material --- / --Dimensions W x D x H(mm) --Description of Origin ---

W/Color Photo Label No Dimensions W x D x H(mm) 575x322x441 Description of Origin Yes

Height (cm) 80

Rear PS 94V0 DECABROM Jack Panel --

Eyelet Demand No

Pb-free Phase3 (Phase3A) Measures for Whisker Yes

Yes F Type

476 x 78.5 x 312.5

Natural Dropping At 1 Corner / 3 Edges / 6

Surfaces

Sets/40' container

A3-5

+ 93 hidden pages