Toro 79402 Operator's Manual
FORM NO. 3315–421
Vacuum Bagger
for 52” Mowers on Z-118 and 616\620
Model No. 79402 – 790001 & Up
Operator’s Manual
IMPORTANT: Read this manual carefully. It contains information about your
safety and the safety of others. Also become familiar with the controls and
their proper use before you operate the product.
Introduction
Thank you for purchasing a Toro product.
All of us at Toro want you to be completely satisfied
with your new product, so feel free to contact your
local Authorized Service Dealer for help with service,
genuine Toro replacement parts, or other information
you may require.
Whenever you contact your Authorized Service
Dealer or the factory, always know the model and
serial numbers of your product. These numbers will
help the Service Dealer or Service Representative
provide exact information about your specific
product. You will find the model and serial number
plate located in a unique place on the product as
shown below.
1
Read this manual carefully to learn how to operate
and maintain your product correctly. Reading this
manual will help you and others avoid personal injury
and damage to the product. Although Toro designs,
produces and markets safe, state-of-the-art products,
you are responsible for using the product properly
and safely. You are also responsible for training
persons who you allow to use the product about safe
operation.
The Toro warning system in this manual identifies
potential hazards and has special safety messages that
help you and others avoid personal injury, even death.
DANGER, WARNING and CAUTION are signal
words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
DANGER signals an extreme hazard that will cause
serious injury or death if the recommended
precautions are not followed.
WARNING signals a hazard that may cause serious
injury or death if the recommended precautions are
not followed.
1. Model and Serial Number Plate
For your convenience, write the product model and
serial numbers in the space below.
Model No:
Serial No.
1815
CAUTION signals a hazard that may cause minor or
moderate injury if the recommended precautions are
not followed.
Two other words are also used to highlight
information. “Important” calls attention to special
mechanical information and “Note” emphasizes
general information worthy of special attention.
The left and right side of the machine is determined
by sitting on the seat in the normal operator’s
position.
Printed in USA
The Toro Company – 1996
All Rights Reserved
Contents
Safety and Instruction Decals 2. . . . . . . . . . . . . .
Assembly 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loose Parts 3. . . . . . . . . . . . . . . . . . . . . . . . .
For Optimum Performance with your
Vacuum Bagger 4. . . . . . . . . . . . . . . . . . . .
Mower Preparation 5. . . . . . . . . . . . . . . . . . .
Installing the Blower 7. . . . . . . . . . . . . . . . .
Installing the Canister 10. . . . . . . . . . . . . . . .
Installing the Hose 11. . . . . . . . . . . . . . . . . . .
Page
Page
Operation 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emptying the Canister 14. . . . . . . . . . . . . . . .
Maintenance 15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Interval Chart 15. . . . . . . . . . . . . . . .
Maintenance and Storage 15. . . . . . . . . . . . . .
Replacing the Drive Belt 16. . . . . . . . . . . . . .
Lubrication 16. . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Blower Wear Strip 17. . . . . . . .
1
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near
any area of potential danger. Replace any decal that is damaged or lost.
ON BLOWER HOUSING
(Part No. 93–1122)
ON BLOWER HOUSING
AND
BELT COVER
(Part No. 79–0350)
ON BLOWER
MOUNTING PLATE
(Part No. 82–5510)
ON TOP OF BLOWER
HOUSING
(Part No. 79–0360)
ON CANISTER
SUPPORT
(Part No. 79–3970)
2
Assembly
Loose Parts
Note: Use the chart below to verify all parts have been shipped.
DESCRIPTION QTY. USE
Blower deflector
Bolt – 5/16”-18 x 3/4” (19 mm)
Locknut – 5/16”
Drill template
Blower assembly
Dual pulley
V-Belt
Bolt – 5/16”-18 x 3/4” (19 mm)
Locknut – 5/16”
Bracket assembly – welded
Spring clip
Extension spring
Carriage bolt – 3/8”-16 x 3/4” (19 mm)
Locknut – 3/8”
Belt cover
Bolt – 5/16”-18 x 3/4” (19 mm)
Belt shield bracket
Locknut – 5/16”
1
3
3
1
1
1
1
6
6
1
1
1
1
2
1
1
1
2
Install deflector to mower deck
Install blower to mower
Install lift assist spring
Install belt cover and pulley shield
Washer – 11/32”
Bolt – 5/16”-18 x 1/2”, thread-forming
Bagger mount
Support bracket
Bolt – 3/8”-16 x 3/4” (19 mm)
Locknut – 3/8”
Canister
2
4
1
1
2
2
1
Install lower bagger mount and canister to
frame
3
Assembly
DESCRIPTION USEQTY.
Canister support
Bolt – 3/8”-16 x 3/4” (32 mm)
Locknut – 3/8”
Canister top assembly
Bolt – 3/8”-16 x 2-1/4”
Nut – 3/8”-16
Extension spring
Seal
Wire tie
Hose
Adaptor
Hose clamp
POTENTIAL HAZARD
• When Vacuum Bagger is attached to the
tractor, without Front Weight Kit, the
tractor may become unstable.
WHAT CAN HAPPEN
• Loss of traction and stability may cause
loss of tractor control.
1
2
2
1
2
2
2
1
1
1
1
1
Install canister top assembly to canister
support assembly
Install hose
For Optimum Performance
with your Vacuum Bagger
For optimum performance, Toro recommends that
you install a High-lift Blade Kit (p/n 56–2390) and a
Front Baffle Kit (p/n 68–7210) on the mower deck
when you install the Vacuum Bagger.
HOW TO AVOID THE HAZARD
• NEVER operate tractor, equipped with the
Vacuum Bagger, unless the Front Weight
Kit (p/n 81127) is installed.
IMPORTANT: The tractor requires a
minimum of one Front Weight Kit when
equipped with a Vacuum Bagger Attachment.
Two kits should be used if terrain to be cut is
not flat.
Note: The Front Weight kit (part number
81127) is an accessory for the ZRT
Tractor, and is purchased separately
from the Vacuum Bagger Kit.
4
Loading...