Page 1
F E A T U R E S
Workman® HD Series
• Industry leading hauling and towing
capacity :
– 2,899 lb (
– 2,894 lb (1,313kg) total capacity – HDX-D
– 3,500 lb
• Electronic Fuel Injection Per formance –
HDX Models
– Smooth, responsive driving
– Increased fuel economy over carbureted
engines
– Instant cold starting
– Automatic high altitude compensation
– On- board diagnostics
• Four-wheel hydraulic disk brakes for easier
stopping and fast servicing
• Proven ride comfort
– Independent, double A -frame front
suspension with dual coil springs
and shock absorbers provides
5¾” (14.6cm) front travel
–
DeDion rear axle with dual leaf springs
and shock absorbers provide 3” (7.6cm)
rear travel
1,318kg) total capacity – HDX
(1,587kg) towing – all models
Get more work done
every day with confidence.
The new Workman® HD Series is designed with your toughest work challenges
in mind, from the front bumper to the rear bumper and everything in
between. Design components like an I-beam shaped DeDion rear axle,
a truss-like front space frame, integrated wheel bearings and hydraulic disk
brakes on all four wheels provide the highest total carrying capacity in the
industry and make the Workman ready for the toughest challenges.
• Extreme durability
– DeDion rear axle with I-beam design
isolates and protects transmission,
engine and main frame from vehicle
loading
– Integrated wheel bearings provide
enhanced sealing and consistent heavy
load carrying capability
– Front bumper and front fenders
designed to withstand incidental
impacts without damage
Call your Toro distributor at 1-800-803-8676
Page 2
Workman® HD/HDX Series Specifications
ENGI NE
CLUTCH
INSTRUMENTATION
ALTER NATOR
TIRE S
COOL ING SYSTE M
AIR CLE ANER
CLE ARA NCE CIRC LE 2WD
CLE ARA NCE CIRC LE 4W D
FUE L CAPACIT Y
FUE L PUMP
FUE L FILTER
HORN
SOU ND LEVEL
VEHICLE SHIP PING
WEIG HT
VEHICLE ACTU AL
WEIG HT W /O FUEL
TOTAL CAPAC ITY
CARG O BED CAPA CITY
WORKMAN HDX, NO BED, MODEL 07366
WORKMAN HDX, W/BED, MODEL 07367
WORKMAN HDX W/BED, MODEL 07367TC
WORKMAN HDX - 4WD, MODEL 07370
WORKMAN HDX - 4WD, MODEL 07370TC
B&S D aihatsu® 950G EFI, 31.5 hp (23.4 kw),
4-cycle, liquid-coole d, 950 cc, 3- cylinder,
overh ead cams haft, counterbalance d gasoline
engi ne. M echanical governor re gulates to a
maximum of 32 hp at 36 00 rpm. Rear engine
loca tion dire ct c oupl ed to a transaxle. 12-volt
electric sta rter. Fuel Inje ctio n is a closed loop
syste m with oxygen sens or to adjust air/fuel
ratio and man ifold pressure se nsor to a djus t for
altitude. Full pressure lub rication with spin-on oil
filter. Exhaust emissions m eet 2010 EPA, CARB
and Californi a Blue Sky regulation.
6.7” (17 c m) clutch and pres sure plate 6.7” (17 c m) clutch and pres sure plate 6.7” (17 c m) clutch and pres sure plate
Fuel and coolant temperature ga uges. Hour
meter. Oil pres sure, check e ngin e and bat ter y
charge indicator lights. Tach ometer and
speedometer.
60 a mp with elect ronic regulator 60 a mp with elect ronic regulator 25 am p with electr onic regulator
Front: 20” x 9” - 12, 6 -ply rating, turf tre ad
Rear: 24” x 12” - 12, 6-ply r ating, turf tread
Alum inum radiator with 10 fins pe r inch dual pass. Rig ht side m ounted with removable scree n for
debris clean ing. Thermal controlled DC electric fa n.
Remote mounted, heavy-duty 2-st age air c leaner with evacuator valve.
Inside = 32 in (81 cm); Outside = 194 in (493 cm) Inside = 32 in (81 cm); Outside = 194 in (493 cm) Inside = 32 in (81 cm); Outside = 194 in (493 cm)
Inside = 100 in (254 cm); Outside = 300 in (726 cm) Inside = 100 in (254 cm); Outside = 300 in (726 cm) N/A
6.5 gallon (24.6 lite r) 6.5 gallon (24.6 lite r) 6.5 gallon (24.6 lite r)
12V internally regulated 42 psi in -tan k Mechanical pump Diaphragm pu mp
In tank f ilter sock. 10 micron polyes ter depth.
Stan dard, button on dash on 07367TC &
07370TC. Optional on 073 66, 07367 & 07370.
75 db(A)* 85 db(A)* 80 db(A)*
Mode l 07366: 1623 lbs (738 kg)
Mode l 07367: 1951 lbs (887 kg)
Mode l 07367TC: 2725 lbs (1238 kg)
Mode l 07370: 2010 lb s (914 kg)
Mode l 07370TC: 2784 lbs (1265 kg)
Mode l 07366: 1623 lbs (738 kg)
Mode l 07367: 1951 lbs (887 kg)
Mode l 07367TC: 2032 lbs (924 kg)
Mode l 07370: 2010 lb s (914 kg)
Mode l 07370TC: 2091 lbs (950 kg)
Mode l 07367: 2899 lbs (1318 kg)
Mode l 07367TC: 2818 lbs (1281 kg)
Mode l 07370: 2840 lbs (1291 kg)
Mode l 07370TC: 2759 lbs (1254 kg)
Mode l 07367: 2499 lbs (1136 kg)
Mode l 07367TC: 2418 lbs (1099 kg)
Mode l 07370: 2440 lbs (1109 kg)
Mode l 07370TC: 2359 lbs (1072 kg)
WORKMAN HDX - D, MODEL 07368
WORKMAN HDX - D, MODEL 07368TC
WORKMAN HDX - D - 4WD, MODEL 07371
WORKMAN HDX - D - 4WD, MODEL 07371TC
B&S D aihatsu® 950D, 3-cylinder, inline vertical,
4-cycle, liquid cooled, counterbalanced die sel
engi ne. 24 hp (17.9 kw); gove rned to a maximum
speed of 360 0 rp m. Mechanical centrifugal
gover nor. 58.0 cu. in. (950 cc) displacement. Re ar
engi ne location. Direct couple to t ransaxl e. 12volt electric sta rter. Full pres sure lubrication with
spin -on oil filte r. Meets EPA Tier IV complianc e.
Fuel and coolant temperature ga uges. Hour
meter. Oil pres sure, glow plu g and batter y ch arge
indicator lights. Tachometer and speedometer.
Front: 20” x 9” - 12, 6 -ply rating, turf tre ad
Rear: 24” x 12” - 12, 6-ply r ating, turf tread
Comb ination f uel filte r / water separato r with
a 30 micron f iltration and 50 m esh suction screen
in tank.
Stan dard, button on dash on 07368TC &
07371TC. Optional on 07368 & 07371.
Mode l 07368: 1956 lbs (889 kg)
Mode l 07368TC: 2730 lbs (1240 kg)
Mode l 07371: 2015 lbs ( 916 kg)
Mode l 07371TC: 2789 lb s (1268 kg)
Mode l 07368: 1956 lbs (889 kg)
Mode l 07368TC: 2037 lbs (926 kg)
Mode l 07371: 2015 lbs ( 916 kg)
Mode l 07371TC: 2096 lbs (953 kg)
Mode l 07368: 2894 lbs (1315 kg)
Mode l 07368TC: 2813 lbs (1279 kg)
Mode l 07371: 2835 lb s (1289 kg)
Mode l 07371TC: 2754 lbs (1252 kg)
Mode l 07368: 249 4 lbs (1134 kg)
Mode l 07368TC: 2413 lbs (1097 kg)
Mode l 07371: 243 5 lbs (1107 kg)
Mode l 07371TC: 2354 lbs (1070 kg)
WORKMAN HD, MODEL 07369
Kohle r® Model CH23, 2-cylinder, 4-cycle,
air-coole d engine. 23 h p (17.2 kW) @ 3600 rpm
gover ned to a maximum spee d of 3600 rpm
by an inte rnal gove rnor. 41.1 cu. in. (674 cc)
disp lace ment . Electronic ignition. Rea r engine
loca tion dire ct c oupl ed to a transaxle. 12-volt
electric sta rter. Full pres sure lubrication with
spin -on oil filte r. Meets exhaust and evaporative
emis sions for 2010 EPA and CARB.
Fuel gauge, ho ur meter, oil pressure warning li ght
and battery charge i ndic ator light. Tachomete r /
speedometer optio nal.
Front: 20” x 9” - 12, 6 -ply rating, turf tre ad
Rear: 24” x 12” - 12, 6-ply r ating, turf tread
Fan forced air.
Large capacity, dual e leme nt.
In-l ine 40 micron filter and 50 mes h suction
scre en i n tank.
Optional
Mode l 07369: 1848 lbs (840 kg)
Mode l 07369: 1848 lbs (840 kg)
Mode l 07369: 3002 lbs (1364 kg)
Mode l 07369: 26 02 lbs (1183 kg)
Specifications subject to change. Please contact your Toro distributor for details.
* At operator’s ear; 3600 rpm with bed and sides installed.
Page 3
Workman® HD/HDX Series Specifications (continued)
SPECIFICATIONS COMMON TO WORKMAN HD SERIES VEHICLES
FRON T SU SPEN SION
REA R SU SPENSION
BATTE RY
TRA NSMISSI ON
3RD HIGH LOCK OUT
DIFF EREN TIA L LOCK
4WD SYSTE M
FRA ME
STEERING
2-PO ST ROPS
BRA KES
HYDRAUL ICS
LIGH TS
SEAT BELTS / SE ATS
CONTROL S
INTERLOCK
SAF ETY SUP PORT
GROU ND C LEA RANCE
REA R TO W HITCH
GROU ND S PEED
DIME NSIO NS
CERT IFIC ATIONS
WARR ANT Y
Inde pend ent system wit h dual “A” frame control a rms, dual coil sp ring s and dual sh ock absorbers wi th anti-sway bar. Prov ides 5 3/4” trave l.
DeDion r ear axle (weight carr yin g axle) suspension independent of transaxle with d ual leaf springs and dual shock ab sorbers . Provides 3” travel.
12-volt, group 26, with 540 cold cranking amps at 0 degre es F (-18 degrees C).
Rear transaxle directly connected to engine, t win axle drive. 3-spe ed synchromesh (forwa rd s peeds on ly), h-shift pattern with high -low range pr ovidi ng
6 forward speeds and 2 in reverse. Transm ission housing doubles as hydraulic res ervoir w ith outle t screen and exte rnal filter.
Interlock key switch that prevents eng ine from runn ing in 3r d gear, high ra nge.
Manu al engage rear di fferential l ock.
Fully automatic on- demand, bi-directional system. Uses du al bi-di rectiona l clutches. In event of rear tire sli ppag e, clutches transmit power prop ortiona lly to
front wheel with highest t raction.
Steel space f rame front frame and C-channel rear f rame.
Hydraulic power ste ering with wi th steering valve coupled to hydr aulic cylinde r with thru shaft . Ma ximu m ste ering angle is 70 degrees on 2WD
and 50 de grees on 4WD.
2-pos t rollover protective st ructure and protective back pan el bolted to ROPS.
4-wheel hydraulic disk brake sys tem. 9 1/2” disk with hydr aulic servic e br akes using twin piston fix mount ca lipers. Parking b rake uses mechanical cable
actuated caliper on rear w heels.
4 gpm (15 lpm) gear pump provides hydraulic flow for p ower steering and lift in series. Lift control valve with quick di sconnects for dual lift cylinders or for
attachments when quick disconnects are switched. 8 quar t total c apac ity.
Twin halogen headlig hts and dual taillights ac tuate d by switch on dash. Dual brake lights ac tuate d by brake pedal.
Lap seat belts standard. Bucket seats with adjustable slides to allow for various seat positions. Hip restraint tubes welde d to seat mounting straps.
Throttle, brake and clutch pedals. Gear shifter, differential lock, parking brake, high -low range sh ifte r an d hydraulic lift l evers.
To start e ngine, clutch pedal mu st be depressed and remote hydr aulic lever mu st be in neutral position. If i nsta lled, high fl ow hyd raulics and r ear PTO must
be disengage d / switch ed off.
7-gaug e ste el c hann el stores behind seat and fits over extended lif t cylinde r to preve nt accidental lowe ring of b ed.
7” (18 cm) wi th no load.
Steel hitch bracket bolted to rear DeDion axle. Mounting plate provides mounting hole for pin or ball hitch and incorpor ates two safet y chain mounting hole s.
Maximum tongue weight of 600 lbs (272 kg). Maximum trailer weight of 3500 lbs (1587 kg). Trailers over 150 0 lbs. re quire trailer brakes.
Sta nda rd T ires, G ear 1/2/3
Forward Spee ds: High Rang e 7.6/11.5/19.8 mph (12.2/18.5/31.9 km/h)
Low Range 2.9/4.5/7.7 mph (4.7/7.2/12.5 km /h)
Rever se S peeds: High Range 7.1 mph (11.6 km/h)
Low Range 2.8 mph (4.5 km/h)
Ove ral l Le ngth Overa ll W idt h Over all Height (Top o f ROPS)
127.6 in (324 cm) w/o be d 64.7 in (164.3 c m) 75.8 in (192.5 c m)
130 in (330 cm) w/ full be d
Cer tifi ed to meet SAE J2258. Certified to m eet ISO/D IS 21299 for ROPS. Engine meet s all applicable emis sion sta ndar ds per the ma nufacturer. Certif ied to
meet the CE Machinery Directive.
Two-year limited warranty. See Operator’s Man ual for f urther details.
Specifications subject to change. Please contact your Toro distributor for details.
Page 4
Workman® HD/HDX Series Accessories
FUL L AR EA F LAT BED
FUL L FL AT BED SIDE KIT
1/3 FLAT BED
1/3 FLAT BED
STAK E SID E KI T
2/3 FL AT BED
2/3 FL AT BED SIDE KIT
FUL L FL AT BED FOL D
DOWN SIDE KIT
HIGH FLOW HYDRAU LICS KI T
200 GALLON SPR AYER
VICO N SP REA DER
TOPD RES SER 1800
TOPD RES SER 250 0
1/3 VERT ICAL LIF T
HAR D CAB
CAB SLIDING W INDOW
DOOR KIT
CAB SOLI D WI NDOW
DOOR KIT
CAB REA R VI EW M IRRO R KI T
CANOPY
FOLD ING WINDSHIELD
LIGH T KIT “RIGHT SIDE”
LIGH T KIT “L EFT SIDE”
WORK LIGHT K IT
ROPS SIGNAL LIGH T KI T
HEAV Y DUTY POWER
LIF T HOLSTER HI TCH
HEAV Y DUTY HITCH
FRA ME
AUTO MATIC
TAILG ATE RE LEA SE
REA R PTO K IT
HAN D TH ROTT LE
SPARK ARREST OR
PLA STIC BED LINER
HIGH AIR INTAK E K IT
REA R VI EW MIRRO R KI T
Welde d steel diamond plate flat bed that mounts to vehicle fram e. Dimensions: 54.7 x 64.5 in (139 x 164 cm). Weight: 218 lbs (99 kg).
Long bed side pan els, front pa nel and tailgate with a fixed pivot.
Welde d steel diamond plate flat bed. Has (4) corner stake pockets for enhancing specialty mount applic ations. Dimensions: 21.5 x 54.7 in (55 x 139 cm).
Weigh t: 55 lbs (25 kg)
Formed 14-gauge ste el stake side s for use with 1/3 flat b ed.
Welde d steel diamond plate flat bed. Dim ensi ons: 48.1 x 5 4.7 in (122 x 139 cm). Weight: 161 lbs ( 73 kg)
Shor t bed side p anels, front panel an d tailgate with a fixed pivot for use with 2/3 flat bed. Optional tailgate release PN 92-1220.
Hinged side panels, f ront panel and tailgate can be folded down independently for use with full flat bed. Dimensions: 64.5 x 54.7 x 11 in (164 x 139 x 28 cm)
outs ide. 20 cu ft (.570 c u m) capacity. Weight = 109 lbs (49 kg)
Provides 8 gpm (30.3 liter) at 20 00 psi hydrau lic flow in a separate circuit to powe r ce rtain attachments a nd acces sories (standard on TC models).
200 gallon (757 liter) l ow profile tank sp rayer with dia phragm p ump and d etatchable co ntrol box. Three- section, 18.5 ft (5.6 m) open boo m sys tem.
Pendulum action spreader with polye ster hopper. 14.1 cu. ft. (.396 cu. m.), 750 lbs (340.5 kg) capacit y. Spr ead width is 3 - 46 ft . (1 - 14 m).
18 cu. ft. (.504 cu. m), 1450 lbs (541 kg) capacity conveyor belt sty le to pdre sser hydr aulically driven by remote hydraulics . 60 in (152 cm) spread width.
Workman b ed lift cylinder s raise topdresser. Spring load metering gate.
25 cu. ft. (.7 cu. m) capacity conveyor belt style topdresser towed by Wo rkman vehicle. Textu red belt, oscillating axles and all wheel drive.
Elec tric ally activated hydr aulic brakes.
An e levating, scis sor-lift work plat form with 600 lb (272 kg) lif t capacity that can be raised fro m 38 in (96.5 cm) to 98 in (249 cm).
Slop e indicator fo r safe operation. Removable over-ride key fo r lift controls.
Delu xe ha rd cab, ROPS a nd CE certif ied. Vente d front g lass windshield, interior dome light an d a 2-speed windshield wiper.
Optional heater and mi rrors availab le.
Door kit for deluxe hard cab. Operator d oor has a sliding window for ventilation and a bility to acc ess exterior elements such as an identific ation badge
secu rity entry. Passe nger door has sol id window.
Door kit for deluxe hard cab. Operator a nd passe nger doo rs h ave solid windows.
Externally mounted to the cab frame, op erator and pa ssenger side rea r view mirror s for enh anci ng all around visibility.
Durable, high-de nsity polyethylen e canopy with drai nage outlets for moisture runof f.
Clea r high-impact modifie d ac rylic material with fold d own c apab ilit y.
Cons ists of turn signal lights for both corn ers in the fr ont and rear of vehicle and bri ghter beam he adlights.
Head lights are directionally s et for ri ght hand driving and p assing.
Cons ists of turn signal lights for both corn ers in the fr ont and rear of vehicle and bri ghter beam he adlights.
Head lights are directionally s et for left h and driving a nd passi ng.
Cons ists of (2) front facing and (1) rear fa cing work lights a ll mounte d on top of ROPS bar.
Consists of (2) double amber warning lights and (2) single red tail lights all for mounting on top of ROPS bar. Requires either a “Right Side” or “Left Side” light kit.
Hydraulic ally-powered lift hitc h for rea r mounted 2 point arm attachme nts, including those requiring mec hani cal down pres sure or “flo at”. Lift capa city: 50 0
lbs (249 kg). Req uire s heavy-duty hitch fr ame.
Heav y duty h itch frame made of steel pl ate a nd tubula r co nstr ucti on. Designed for use with heav y duty power lift hoster hitch.
Provides autom atic tail gate rele ase when dumping from cargo bed and re sets automatically upo n lowering of bed. Works on full or 2/3 be d with full sides.
Does not work with folding side kit.
Rear mounted, 540 RPM, PTO s haft mechanically dr iven by tr ansaxle.
Mechanical throt tle and s peed limit contro l that pr ovides co nsta nt RPM for sta tionary att achm ents or a controlled m aximum speed for applications suc h as
spraying or s prea ding.
For D aiha tsu engines. Fits onto end of tailpi pe.
A rugged, weather proof one-piece plastic l iner and separate tailgate liner that wi ll protec t either a full are be d with si des or a 2/3 bed with side s.
Kit for extending the air i ntake system from u nderneath the cargo b ed to a position slightly a bove the ROPS s hiel d behind the passenge r po sition of
the vehicle. Recom mended for dusty work applications.
A single 8 1/2” convex mir ror with mounting capa bility o n either the oper ator or passe nger side of the vehicle.
WORKMAN VEHICLE ACCESSORIES
Specifications subject to change. Please contact your Toro distributor for details.
Page 5
Workman® HD/HDX Series Accessories (continued)
WORKMAN VEHICLE ACCESSORIES
5TH WHEEL HI TCH KIT
2” RECEIVER HITCH KIT
TRA ILER BR AKE
WIRI NG K IT
TRA ILER SIG NAL
WIRI NG K IT
REMO TE H YDR AULI C
MAN IFOL D KI T
REMO TE H YDR AULI C
FLOAT KIT
A 5th wheel hitch assembly with a rubber-mounted 2 ” ball hi tch a nd electric brake controller u sed to tow Cushman GA60 Aerator and similar implements.
Provides a 2” square receiver to enable a “drawbar ” hitch.
Kit provi des a controller which plu gs into Workma n veh icle and a positive wire to assi st the ho ok up of customer supplied electric trailer bra kes.
Kit provi des elec tric al wire for Workma n veh icle to enable easy hook up to custom er s upplied trailer signa l an d brake lights.
Hydraulic manifold kit that prov ides to ability to switch hyd raulics between cargo bed actuation and re mote port usage via use of a opertor panel
mounted switch.
Hydraulic float ki t that enables both hyd raulic lifting and “float” in the down position. Required when u sing a Deere TC125 swe eper.
©2009 The Toro Company
8111 Lyndale Ave. S.
Bloomington, MN 55420-1196
Printed in the U.S.A .
Specifications subject to change. Please contact your Toro distributor for details.
Loading...