Toro 51574 Sell Sheet

FEATURES

• 23 hp (17.2 kW) Kohler® Command Pro®
engine

• 4.75 cubic yard (3.6 cubic meter) capacity

®

Rake-O-Vac

A clean sweep.

The Rake-O-Vac’s Kohler® 23 hp engine insures there is plenty of

horsepower to clean debris from the most difficult turf. A spring-loaded

flex tip reel provides exceptional sweeping performance especially

with those annoying pine needles. The large 4.75 cubic yard hopper

provides plenty of capacity for picking up large areas. Compact and

maneuverable, the Toro Rake-O-Vac clears debris from even the

tightest areas. The rugged impeller fan pulverizes leaves and

debris saving space in the hopper yet the airflow in the

hopper minimizes dust by directing it back to the ground

keeping your neighbors happy.

• New airflow
system delivers a
cleaner sweeping
environment

• Spring-Loaded Flex Tip Reel –
Flexible nylon fingers brush the ground
clear of debris utilizing a spring-loaded
design to give the fingers an extra kick
for clearing debris in wet conditions

• Optional Broom Reel provides
additional sweeping power

©2013 The Toro Company
All rights reser ved.
8111 Lyndale Ave. S.
Bloomington, MN 55420-1196
Printed in the U.S.A. Rev. 2/13

Call your Toro distributor at 1-800-803-8676

Rake-O-Vac® Specifications*

Kohler® Command Pro® CH680, 23 hp (17.2 kW) @ 3600 rpm, 4 cycle, air-cooled, V-twin cylinders, horizontal crankshaft with a 5.5" (14 cm) dry centrifugal clutch.

POWER SUPPLy

FAN IMPELLER

DRIVE

FAN HOOD

REEL/BRUSH DRIVE

MAIN FRAME

WHEELS AND TIRES

HOPPER

HITCH

FLEX TIP REEL

DIMENSIONS

WEIGHT

WARRANTy

Compression ratio: 8.5:1. Overhead placement valves; intake, forged high carbon steel, exhaust Stellite
liter) with filter, oil capacity. 12-volt, 15 amp alternator with solid state regulator/rectifier. Solid state electronic ignition system with electronically controlled spark
advance. Tri-phase design with screen pre-cleaner, replaceable filter cartridge and dump valve.

Centrifugal type housing, double inlet. Four alloy steel blades, 16" (41 cm) wide x 23.25" (59 cm) diameter, .1875" (4.8 mm) thick. High tensile, .5625" (4 cm) stress-proof steel shaft mounted
in self-aligning sealed ball bearings. Blower discharge area: 255 in

Banded double. B-80 drive belt direct from drive shaft to fan impeller drive shaft. Fan impeller runs at 1580 rpm [tip speed 9,720 ft/min. (2963 m/min.)] at 3250
engine rpm.

Twin construction for uniform air distribution; 4.5" (11.4 cm) deep x 63" (160 cm) wide. Inlet area: 283 in2 (1826 cm2).
Variable position, front weighted rubber flap.

Belted-double B-53 drive belt from engine to jack shaft. Banded (4) 3V cross section belt, from jack shaft to flex tip reel.
Flex tip reel runs at 275 rpm [tip speed 1,355 ft./min. (413 m/min.)] at 3250 engine rpm.

All welded, structural, rectangular, 2" x 4" (5 cm x 10 cm) and 4" x 4" (10 cm x 10 cm), 11-gauge, steel tubing.

High flotation type I-1 rib tread, 11L-14SL, 6 ply rating, tubeless construction mounted on 8" (20 cm) x 14" (36 cm) wheel with six bolt attachment. Inflation
pressure 28 psi (1.9 bar).

4.75 cu. yd. (3.6 m3) volume; 18-gauge top section with 16-gauge bottom section - rib reinforced; full width, self-cleaning,
semi-automatic dumping.

Pin type, .75" (1.9 cm) diameter; adjustable vertical height for tractor hitches from 7.25" (18.4 cm) to 17.25" (43.8 cm) height.

Forward sweeping, 6 rows of teeth, all steel construction with replaceable .1875" (4.8 mm) extruded nylon teeth; each row containing 11 individually spring
loaded flexible sets, 552 total teeth, 18.75" (48 cm) diameter reel, 61" (155 cm) wide, 1.125"
(2.9 cm) diameter shaft set in self aligning sealed bearings. Reel supported by adjustable counterbalance springs and adjustable-gauge wheels. Gauge wheels
aluminum construction with non-scuffing rubber tires operating on greaseable ball bearings;
infinitely adjustable vertically.

Width Height Length

85.5" (217 cm) 79.5" (202 cm) 13'3" (4.0 m)

2,980 lbs. (1,355 kg)

Two-year limited warranty. Refer to the Operator’s Manual for further details.

RAKE-O-VAC ENGINE DRIVE, MODEL 07055

®

faced. Hydraulic valve lifters. Full pressure 4 pint (2.3

2

(1645 cm2).

BRUSH

OPTIONAL EQUIPMENT

Forward sweeping continuous, polypropylene bristle, floating action provided by spring counterbalance and gauge wheel height adjustment. Model 07162.

Brush speed: 275 rpm [tip speed 1,370 ft./min. (417 m/min.)] at 3200 engine rpm.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.
“Stellite” is a trademark of Stoody Deloro Stellite, Inc.