Toro 21062, 21072 Parts Catalogue
Electric - Recycler
®
34 cm / 40 cm
ModelModel
Model
ModelModel
34 cm34 cm
34 cm
34 cm34 cm
40 cm40 cm
40 cm
40 cm40 cm
Serial-No.:Serial-No.:
Serial-No.:
Serial-No.:Serial-No.:
Operator's ManualOperator's Manual
Operator's Manual
Operator's ManualOperator's Manual
2106221062
21062
2106221062
2107221072
21072
2107221072
230 000 101 & up.230 000 101 & up.
230 000 101 & up.
230 000 101 & up.230 000 101 & up.
© by The Toro Company
General 3
Maintenance and Upkeep 15
Safety 5
Assembly and Start-up 7
Operation 11
Spare Parts and Troub leshooting 17
Hints on T ending the La wn 23
2
© by TORO Company
1 General
1.1 Introduction
1.2 Regulation on time limits for the operation of lawn
mowers
1.3 Technical data
1.1 Introduction
The TORO lawn mower has been designed according to the
latest technical and physiological aspects with due regard to the
safety regulations in force.
With its special equipment the Recycler
grass and leaves several times. This superfine-cut material will
be sprinkled into the lawn by the mower.
Read the instructions for use carefully and familiarize yourself
with the instructions on safety, assembling, operation and
maintenance.
The TORO lawn mower has been designed for the private use in
the garden. Lawn mowers for the private garden are units which
are - as a rule - in use for not more than 50 hours per year, and
which are mainly used for the tending of patches of grass and
lawns; they are, however, not to be used in public gardens,
parks, sports fields etc. and not on roadsides nor in the agriculture and forestry.
The observance of the instructions for use enclosed by TORO is
a prerequisite for the proper use of the lawn mower. The instructions for use also enclose the conditions of operation, maintenance and upkeep.
Safety
On-the-job safety symbol, this symbol you will find
with all on-the-job safety instructions dealing with
danger of personal injury. It is imperative to observe
these instructions. The on-the-job safety instructions
should be passed on to other users as well. The
general regulations for safety and prevention of
accidents must also be observed.
Warning sign, this symbol marks the points which are
to be taken special notice of in order to avoid
damaging or destroying the unit.
®-
-Mower can cut up
1.2 Regulation on time limits for the operation of lawn
mowers.
The regulations on the operation of lawn mowers vary from one
region to another. The competent authority will be pleased to
inform you on regulations and regional restrictions, especially as
to the protection of the period of quiet after lunch or of very
sensitive areas (e. g. nature reserves),
1.3 Technical data
Electro Recycler 34 cm
width of cut: 34 cm
motor type: CRB 52/21A with brake
output: 1050 W
voltage: 230 V~ 50 Hz
amperage: 5,3 A
motor speed: 2800 min
vibrations on the
handle bar ahw: 4 m/sec
-1
2
(measured in accordance with pr EN 1033)
weight: 17 kg
dimensions : L x W x H = 80 x 38 x 35 cm
(folded up)
Electro Recycler 40 cm
width of cut: 40 cm
motor type: CRB 72/21A with brake
output: 1300 W
voltage: 230 V~ 50 Hz
amperage: 6,0 A
motor speed: 2800 min
vibrations on the
handle bar ahw: 4 m/sec
-1
2
(measured in accordance with pr EN 1033)
weight: 19 kg
dimensions: L x W x H = 88 x 44 x 35 cm
(folded up)
© by TORO Company
3
EC Declaration of Conformity
We The Toro Company
8111 Lyndale Ave.So.
Bloomington, MN 55420-1196, USA
Declare that the machine "Lawnmower, walk behind and mains-operated (EN836)"
Type: TORO 21062,
Cuttingwidth: 34 cm motor speed: 2800 min
Type: TORO 21072,
Cuttingwidth: 40 cm motor speed: 2800 min
Conforms to the specifications of the following EC directives: 98/37/EG, 73/23/EWG, 89/336/EWG, 84/538/EWG, 2000/14/EG
Where appropriate applied standards: EN836, EN60335-1, DIN VDE 0700 Teil 206, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3
Conformity assessment procedure followed: Annex VI
Measured sound power level: TORO 21062: 84,2 dB(A)
TORO 21072: 87,2 dB(A)
Guaranteed sound power level: TORO 21062: 85 dB(A)
TORO 21072: 89 dB(A)
Storage of the technical documents:
Technical office of Roth Motorgeräte GmbH
Bloomington, MN, USA 01.10.2002 Jerry Patrin VP Technical Manager
Place Date Signature Representative
-1
-1
output: 1050 W
output: 1300 W
4
© by The Toro Company
2 Safety
2.1 General notes
2.2 Proper use
2.3 Improper use
2.4 Preparing the lawn mower for safe operation
2.5 Safe operation
2.6 Safe maintenance and storage
2.7 List of symbols
2.1 General notes
1. Read the instructions carefully. Familiarize yourself with the
operating elements and the proper use of the unit.
2. Children as well as persons who are not familiar with the
instructions for use must not operate the lawn Observe the
local age limits for the operation of the unit.
3. Do not start the mower in close proximity to children and
pets.
4. The operator is liable for injuries of third parties and damages
of their property.
2.2 Proper use
The lawn mower serves exclusively for the tending of grass
patches and lawns in the private garden. Any other use is
regarded as inexpedient. Roth Motorgeraete GmbH is not liable
for damages resulting from this.
2.3 Improper use
The mower must not be used for the trimming of bushes, hedges
and shrubs, for the cutting of creepers or grass on roof gardens
or in balcony boxes, for the cleaning (by suction, blowing away;
snow removal) of sidewalks nor as a chaffcutter for chopping cutoff twigs and branches of trees and hedges. Moreover, the mower
must not be used as drive unit for other interchangeable equipment items and tool kits. It is also regarded as inexpedient to use
the unit for pulling lawn sweepers and barrow-type spreaders.
The same holds true for the attachment of trailers, e. g. to ride
along with or for transporting cut material except with the grass
collecting sack which TORO designated for this purpose.
2.4 Preparations for safe operation
1. You should always wear sturdy shoes and trousers when
mowing. Do not mow barefoot or wearing sandals.
2. The area to be moved must be checked. Objects like stones,
sticks, wires, bones a.s.o. must be removed first.
3. Make a visual inspection before starting the motor and check
for damages and wear on cutter bar, fastening screws of
cutter and cutting parts.
Worn or damaged cutters and screws must always be
exchanged in sets to keep the balance.
4. To avoid fire and motor overheating, always the air entry
around the engine has to be kept clean from any grass,
leaves and dirt.
2.5 Safe operation
1. Mow only in daylight or with good illumination.
2. Do not mow grass when wet.
3. Make sure to have a firm foothold when mowing on sloping
ground.
4. Mow at a walking pace, do not run.
5. With a wheeled rotary mower you should always mow
sideways to the slope, never up and down.
6. Be careful when changing direction on sloping ground.
7. Do not mow on extremly sloping ground.
8. Be careful when moving the lawn mower backward or pulling
it.
9. Stop the engine, if you have to tilt the lawn mower when
walking off the grass to cross paths. Transport the machine to
the area to be mowed and back with the motor off.
10. Never operate the lawn mower without safety devices e. g.
impact protection and/or grass collecting elements.
11. On starting the motor, all instructions are to be observed, and
attention is to be paid that the feet are in a safe distance to
the cutters.
12. Do not tilt the lawn mower when starting the motor, unless the
motor has to be tilted for this purpose. In this case, the unit
must not be tilted more than absolutely necessary, to be more
precise, the mower may only be tilted backward, so that the
bottom side with the cutters is not turned towards the
operator
13. Keep away from the grass ejection opening when starting the
motor.
14. Never put your hands and feet on or under rotating parts.
Keep a due distance to the ejection hole.
15. Do not lift or carry the lawn mower with the motor running.
16. In the following cases, the motor is to be stopped and the
mains plug is to be disconnected:
• before removing chokings resp. obstructions in the ejection
channel
• before inspecting, cleaning or performing any other work on
the lawn mower;
• after the lawn mower has hit against a foreign matter. Check
your lawn mower for damages and make the necessary
repairs before further use of the lawn mower.
• if the unit starts to vibrate heavily (immediate inspection
required).
17. Switch off the mower and pull the cable connector, before
adjusting or cleaning the mower. This is olso true, before the
cable is checked for demage or interlace.
18. In accordance with VDE standard 0282, for electric mowers
only extension cables with a metallic section of at least 1.5
mm² of the type HO5RN-F or HO7RN-F may be used. The
coupler plugs and socket connections of the connecting
cables must be made of rubber or rubber-covered, splashproof and in accordance with VDE standard 0282.
TORO cables conform to this requirement. Check the cable
periodically for signs of defects. It may only be used if
undamaged.
2.6 Safe maintenance and storage
1. Ensure that all nuts, bolts and screws are tightened to
guarantee a safe operating state.
2. Check the grass collecting sack at short, regular intervals for
wear and damages.
3. For safety reasons, worn or damaged parts are to be
exchanged.
© by The Toro Company
5
2.7 List of symbols
„Motor ON“
„Motor OFF“
„Adjustment of cutting height“
Warning
Read the instructions for use before starting
Third parties have to be kept out of the hazardous
area
Warning! Rotating cutter!
Keep hands and feet off
Electrical shock / electrocution
Keep dry
Disconnect mains plug before
servicing the cutting tool
Always keep connecting cable away from blade.
If the blade catches or cuts the cord, immediately
unplug the cable from the outlet.
6
© by The Toro Company
10
10
3 Assembly and start-up
3.1 Become acquainted with your lawn mower
3.2 Setting the lawn mower up
3.3 Mounting the wheels
9
1
6
7
3
2
8
5
4
3.4 Mounting the handlebar
3.5 Attaching the grass collecting device
3.6 Adjusting the cutting height
3.7 Proper cutting height
3.8 Connecting the lawn mower
3.1 Become acquainted with your lawn mower
1 ON-OFF switch
For turning the mower on and off.
2 Height adjustment of handlebar
3 Pushbutton for adjustment of cutting height (6 steps)
4 Cutting height scale
Scale indicating the adjusted cutting height
5 „Smart Wheel“ scale
Scale for adjusting the proper cutting height
6 Ejection door
Guard for the ejection opening which must not be removed. It
also serves as a stacker for the cut grass when mowing
without collecting device.
7 Grass-collecting device
Device for collecting the grass during mowing.
8 Recycler® plug
To recycle, close the ejection channel with it.
For mowing with the grass collecting device or if a deposition
of the grass is desired, remove the Recycler® plug
9 Cable strain relief
Protects plug-in socket and socket connection from extreme
pull
10 Carrying handles
© by The Toro Company
1
7
3.2 Setting the lawn mower up
1. Open the tapes and lift the upper part of the carton (Fig. 2).
2. Take out the components and put them down (Fig. 2).
3. Check completeness of contents.
Dispose packaging according to the local regulations.
3.3 Mounting the wheels
Note: First mount the wheel bearing with the ”Smart-
Wheel” scale on the left in the back.
2 3 4
5
6
1. Push the wheel bearing the ”Smart-Wheel“ scale on the lefthand side in the back onto the axle until engaged (Fig. 3).
2. Mount the other wheels.
Wheels must engage on the axles.
3.4 Mounting the handlebar
The cable must not be bent, pinched or damaged.
1. Unscrew the tommy nuts on the sides of the mower rear and
pull up the lower part of the handlebar until the locks engage
7
into the groove on the housing (Fig. 4 + 5).
2. Fasten the tommy nuts fingertight.
3. Add the upper part of the handlebar and put the screws from
the outside inwards into the bore holes (Fig. 6).
4. Fasten the upper part of the handlebar by screwing down the
butterfly nut fingertight.
5. Adjust the height of the handlebar with the tommy nuts on the
mower housing - asdjusting range approx. 10 cm (Fig.7).
8
© by The Toro Company
Loading...