Toro 132-3143 Parts Catalogue

REV: 1/31/13 Form No. 0453-828

Arctic Cat® Prowler

Installation Instructions - Accessory Kit

LXC HDX Rear Panel Kit

(p/n 1436-595)

 NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain
these Installation Instructions for future reference.

Kit includes:

p/n QTY DESCRIPTION

0541-063 1 Upper Panel (1)
0541-064 1 Lower Panel (2)
0541-067 1 Left-Side Lower Panel (3)
0541-066 1 Right-Side Lower Panel (4)
0541-068 2 Rubber Boot (5)
0541-065 1 Sliding Window Assembly (6)
2441-241 2 C-Clamp (7)
* 11 Button-Head Screw (M6 x 16 mm) (8)
* 2 Button-Head Screw (M6 x 20 mm) (9)
* 4 Nylon Lock Nut (M6) (10)
* 13 Rubber Washer (11)
* 13 Fender Washer (12)
** 1 Upper Foam Seal (13)
** 1 Rear Panel Trim (14)
** 2 Side Panel Foam (15)
** 1 Lower Panel Foam (16)
** 1 Seat Belt Trim (17)
0453-828 1 Instruction

* Included in Hardware Kit (p/n 0541-062)
** Included in Foam/Seal Kit (p/n 0541-069)

Parts illustration on page 2

 NOTE: If LXC doors are not being used, side
restraints must be installed and lower side panels
# 3 and #4 from this kit do not need to be installed.

1. Lift up the cargo box; then remove and retain the
four cap screws securing the backrest assembly to
the frame.

2. Slide Rear Lower Panel on the front side of the
rear ROPS tubes and between the backrest assem­bly and the frame; then loosely install the cap
screws securing the backrest assembly to the
frame making sure the top two screws are installed
through the rear panel. See Fig. 1.

4. Slide Rubber Boot around the tube and place the
edge of the lower panel between the lips of the
rubber boot with the slit positioned at the top.

5. Position Upper Panel onto the back side of the rear
ROPS tubes and on the front side of the lower
panel making sure to install the rubber boots
between the both panels. See Fig. 2.

Fig. 2

UTV-171A

6. Position the upper panel so the holes in the panel
align with the holes that secure the taillight.

7. Loosely secure the upper rear panel to the rear
ROPS tubes using two C-Clamps, two Button­Head Screws (M6 x 20 mm) (installed on the out­side), two Rubber Washers, two Fender Washers,
and two Nylon Lock Nuts. See Fig. 3.

Fig. 3

Fig. 1

UTV-187

3. Remove and retain the two torx-head screws and
nuts securing the rear taillight to the ROPS.

UTV-173A

8. Install the taillight using the existing torx-head
screws and nuts; then tighten the screws and nuts
from step 6. Tighten securely.

1

9. Secure the upper and lower panels together using
five Button-Head Screws (M6-1.0 x 16 mm), five
Rubber Washers, and five Fender Washers. See
Fig. 4.

Fig. 4

ROV-162A

10. Install LXC Door Kit (p/n 1436-594) with the
instructions provided within that kit.

11. Install Right- and Left-Side Panels using six but­ton-head screws (M6 x 16 mm) See Fig. 5.

Fig. 5

ROV-188A

12. Tighten all screws securely.

 NOTE: If doors are not being used, side restraints
must be installed.

2

Printed in the U.S.A. ®™Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701 0113