Toro 132-3141 Parts Catalogue
Form No. 0453-731
Arctic Cat® Prowler
Installation Instructions - Accessory Kit
LXC Windshield Kit
(1436-501)
NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain
these Installation Instructions for future reference.
Kit includes:
p/n QTY DESCRIPTION
2441-243 1 Windshield Glass
2441-242 1 Top Sealing Foam
2441-244 2 Gas Spring
2441-241 4 C-Clamp
2441-247 1 Grab Handle
2441-245 1 Grab Catch Support
2441-246 1 Grab Catch
* 2 Machine Screw (M6-10 x 14 mm)
* 2 Machine Screw (M6-1.0 x 16 mm)
* 2 Machine Screw (M6-1.0 x 20 mm)
* 2 Machine Screw (M6-1.0 x 25 mm)
* 2 M6 Fender Washer
* 4 Flange Lock Nut
* 4 Lock Nut (M8-1.25)
* 2 Grab Catch Screws w/Rubber Well Nuts
* 4 Rubber Washer
* 4 Fender Washer
0453-731 1 Instructions
*Included in Hardware Kit (p/n 1436-705)
1. Assemble Grab Catch (B) onto Grab Catch Support (C)
using two Machine Screws (M6-1.0 X 16 mm) (A) and
two Flange Lock Nuts (D) (finger tighten at this time).
See Fig. 1.
Fig. 1
2. Secure the grab catch support (D) onto the lower center
part of Windshield Assembly using two Machine
Screws (M6-1.0 X 14 mm) (A), two Fender Washers
(#B), and two Rubber Washers (C). See Fig. 2.
Fig. 2
UTV-161A
NOTE: If Roof Kit (p/n 1436-500) is installed, go
to step 3. If not, go to step 4.
3. Remove and retain the C-clamps securing the roof to
the ROPS tubes; then remove the roof. See Fig. 3.
Fig. 3
UTV-160A
UTV-162
1
4. If you plan to proceed with the installation of the
Roof Kit (p/n 1436-500) or it will be mounted on
your vehicle at this time, apply Self-Adhesive
Foam (A) on top of the windshield. If not, keep it
for future installation.
Fig. 4
UTV-157A
5. Position the windshield assembly on front of the
ROPS tubes. See Fig. 5.
Fig. 5
7. Fasten the lower part of the windshield assembly onto
the front vertical tubes of the ROPS using two C-clamps
(A), two machine screws (M6-1.0 X 20 mm) (C), and
two fender washers (B) (finger tighten at this time). See
Fig. 7.
Fig. 7
UTV-165A
8. Make sure that the upper part of the windshield
assembly is well supported on the ROPS. If the
bottom frame is not well supported against the
ROPS, loosen the four machine screws (two on
each side) connecting the side main frames to the
lower main frame. Adjust and tighten the four
machine screws (see Fig. 8). Tighten all machine
screws attaching the C-clamps installed in steps 6
and 7.
UTV-163
6. Fasten the upper part of the windshield assembly onto
the front horizontal tube of the ROPS using two Cclamps (D), two machine screws (M6-1.0 X 25 mm)
(A), fender washers (B), two rubber washers (C), and
flange nylock nuts (M6-1.0) (E) (finger tighten at this
time). See Fig. 6.
Fig. 6
Fig. 8
UTV-167
9. Insert the ends of the gas spring (A) into the holes
on the windshield frame and secure using the two
nylock nuts (M8-1.25) (B). Repeat step for the
opposite side. See Fig. 9.
Fig. 9
UTV-164A
UTV-169A
2
Loading...