![](/html/a2/a2cb/a2cbdf9babb955c8fecbe4c25b778a9b706b442a7e2a608bfd21781550e5c147/bg1.png)
Form No. 0453-592
Arctic Cat® ATV/Prowler
Installation Instructions - Accessory Kit
4-Season Clutch Kit
(p/n 1436-332/333/614)
NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain
these Installation Instructions for future reference.
1436-614/332 kit includes:
p/n QTY DESCRIPTION
0823-295 8 Roller
0823-292 1 Spacer
0453-592 1 Instructions
1436-333 kit includes:
p/n QTY DESCRIPTION
0823-292 1 Spacer
0453-592 1 Instructions
NOTE: It is recommended that this kit be
installed by an authorized Arctic Cat ATV dealer.
NOTE: Refer to the appropriate Arctic Cat ATV/
ROV Service Manual for more specific instructions.
1. On Prowler models, remove the seats and center
console and floor; then remove the left-side seatbase. Retain all hardware.
NOTE: On Prowler HDX models, remove the seat,
seat base, and floor. Retain all hardware.
2. On ATV models, remove the right-side footwell.
Retain all hardware.
Fig. 2
ATV-1151
6. Remove the movable drive face plate; then remove
and retain existing rollers.
7. Install new Rollers. See Fig. 3.
Fig. 3
3. Remove the machine screws securing the V-belt
cover. Retain all machine screws.
4. Remove the nut and flat washer securing the drive
clutch. Retain nut and flat washer. See Fig. 1.
NOTE: The clutch assembly must be cleaned
before proceeding.
Fig. 1
ATV-1150
5. Remove the movable drive face and spacer. See
Fig. 2.
ATV-1152A
8. Install new Spacer and existing spacer. See Fig. 4.
Fig. 4
ATV-1153A
1
![](/html/a2/a2cb/a2cbdf9babb955c8fecbe4c25b778a9b706b442a7e2a608bfd21781550e5c147/bg2.png)
CAUTION
Release the belt tension by installing a machine
screw (removed in step 2) into the driven pulley
until the pulley is completely opened or damage
may occur.
9. Install existing movable drive face plate; then
install movable drive face onto clutch housing.
See Fig. 5.
Fig. 5
Fig. 7
GZ075
NOTE: At this time remove the machine screw
from the driven pulley.
11. Rotate the V-belt and drive clutch and driven pulley until the V-belt is properly seated in the driven
pulley.
NOTE: The V-belt will not be flush with the driven
pulley with this kit installed. See Fig. 8.
ATV-1154
10. Using Spanner Wrench (p/n 0544-005), secure the
drive clutch with flat washer and nut (threads
coated with red Loctite #271). Tighten the nut to
165 ft-lb. See Fig. 6 and 7.
CAUTION
Make sure the splines extend beyond the drive
face or a false torque reading and spline damage
will occur.
Fig. 6
ATV-1155A
Fig. 8
UTV-298A
12. Secure the V-belt cover using existing machine
screws. Tighten to 8 ft-lb.
13. On ATV models, install existing right-side footwell using existing hardware.
14. On Prowler models, install the floor, left-side seat
base, console, and seats.
NOTE: On Prowler HDX models, install the floor,
seat base, and seat.
Printed in the U.S.A. ®™Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701 0211
2