Toro 117-3825, 117-3826, 119-4240 Installation Instructions
FormNo.3368-137RevA
CEKit
forModel78551,78552or78553BlowerandDriveKitfora48in,
52inor60inBaggingSystem
ModelNo.117-3825
ModelNo.117-3826
ModelNo.119-4240
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Note:Thiskitneedstobeinstalledonmodel78551,78552or78553BlowerandDriveKittocreateaCEbagger.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
1
2
3
4
5
Nopartsrequired
Warningdecal1
Covermissingdecal
Blowercover1
Bolt(1/4x3/4inch)
Washer(1/4inch)
Washer(5/16inch)
Plasticplug1
Pushnut(1/4inch)
Leftguard
Backguard1
Frontguard1
Lowerguard1
Bolt(5/16x3/4inch)
Flangenut(5/16inch)
Muferguard
Qty.
Use
–
1
1
1
1
1
1
1
1
1
Preparethemower.
Installthedecals.
Installthecovers.
Installtheguards.
Installthemuferguard.
1
PreparingtheMower
NoPartsRequired
Procedure
1.Thoroughlycleanmowerdeck.Alldebrismustbe
removedtoensurethekitwilltproperly.
2.Repairallbentordamagedareasandreplaceany
missingparts.
©2011—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
2
g013161
3
InstallingtheDecals
Partsneededforthisprocedure:
1Warningdecal
1
Covermissingdecal
Procedure
1.Removetheexistingblowercover(
thehardware.
2.Cleantheareawherethedecalswillgo(Figure1).
3.InstallthedecalsasshowninFigure1.
Figure2).Save
InstallingtheCovers
Partsneededforthisprocedure:
1Blowercover
1
Bolt(1/4x3/4inch)
1
Washer(1/4inch)
1
Washer(5/16inch)
1Plasticplug
1
Pushnut(1/4inch)
Procedure
1.Removetheexistingbeltcoverretainingknoband
discard.
2.Removetheexistingbeltcover(Figure2orFigure3).
3.Attachthebolt(1/4x3/4inch)andaatwasher
(5/16inch)tothebeltcoverwithaatwasher(1/4
inch)andpushnut(1/4inch)(
4.Installthebeltcoverandtightenthebolt(1/4x3/4
inch)(Figure2orFigure3).
Figure2orFigure3).
1.Covermissingdecal
Figure1
2.Warningdecal
5.Installthenewblowercoverusingtheexisting
hardwarepreviouslyremoved(Figure2orFigure3).
6.Installtheplasticplugintheexistingbeltcover
Figure2orFigure3).
(
2
g013159
7
8
g013160
4
7
4
InstallingtheGuards
Partsneededforthisprocedure:
1
Leftguard
1Backguard
1Frontguard
1Lowerguard
1
Bolt(5/16x3/4inch)
1
Flangenut(5/16inch)
Procedure
Figure2
Formodel78551(48inch(122cm))and78552(52inch
(132cm))
1.Existinghardware5.Plasticplug
2.Newblowercover6.Existingbeltcover
3.Bolt(1/4x3/4inch)7.Washer(1/4inch)
4.Washer(5/16inch)8.Pushnut(1/4inch)
1.Removetheexistinghardwarearoundtheblowerfor
theleftguard,lowerguardandbackguard(
Figure4
orFigure5).Saveallexistinghardware
2.Installtheleftguardwithexistinghardware(Figure4
orFigure5).
3.Installthebackguardwithexistinghardware
(Figure4orFigure5).
4.Installthelowerguardwithexistinghardware
Figure4orFigure5).
(
5.Installthefrontguardwithabolt(5/16x3/4inch)
andaangenut(5/16inch)(Figure4orFigure5).
Figure3
Formodel78553(60inch(152cm))
1.Existinghardware5.Plasticplug
2.Newblowercover6.Existingbeltcover
3.Bolt(1/4x3/4inch)7.Pushnut(1/4inch)
4.Washer(5/16inch)
3
Loading...