10
0
X
XC9110/XC9111 Series
ETR0406-006a
PFM Controlled Step-Up DC/DC Converter / Controller ICs
■GENERAL DESCRIPTION
The XC9110/9111 series is a group of PFM controlled step-up DC/DC converter/controller ICs designed to generate low supply
voltage by the combination of PFM control and CMOS structure. The series is ideal for applications where a longer battery life is
needed such as in portable communication equipment. With a built-in 2.5ΩN-channel driver transistor, the XC9110A/C/E and
XC9111A/C/E types provide a step-up operation by using only a coil, a capacitor, and a diode connected externally.
The XC9110/9111B, D and F versions can be used with an external transistor for applications requiring larger currents.
Output voltage is internally programmable in a range from 1.5V to 7.0V in increments of 0.1V (accuracy:± 2.5%).
Maximum oscillation frequency is set to 100kHz for XC9110/9111 series. (At light loads, it is set to 180kHz for the XC9111
series.) Options include products equipped with a CE pin (C and D versions) that allows the IC to be shut down thereby
reducing supply current and with separated VDD/VOUT pins (E and F versions) to separate the power supply block and the
output voltage detect block. With the XC9110 series, maximum duty cycle is set to 75% (VDD=3.3V) making it suitable for
use with large current operations. The XC9111 series automatically switches duty ratio between 56% & 75% (VDD=3.3V)
when it senses changes in load to drop output ripple voltage and can support both large and small currents. The external
transistor types (B/D/F types) can be provided for applications, which require larger currents
■APPLICATIONS
●Mobile phones
●Various palm top equipment
●Cameras, VCRs
●Various portable equipment
■ FEATURES
Operating (Input) Range
Output Voltage Range : 1.5V~7.0V in 0.1V increments
Output Accuracy : ±2.5%
Max Oscillation Frequency : 100 kHz ±15%
180 kHz (at 56% duty of XC9111)
Built-in Switch Types : A/C/E type
N-ch FET On-Resistance : 2.5Ω@ V
External Transistor Types : B/D/F type
Lx Limit Voltage : E type: more than V
: A/C type: more than V
Max Duty Cycles : 75% (for XC9110)
: 56%/75% two steps (for XC9111)
Low Supply Current : 2.0μA @ V
Operating Ambient Temperature
Packages : SOT-23 ,SOT89 (for XC9111),
SOT-25, USP-6C
Environmentally Friendly : EU RoHS Compliant, Pb Free
.
: 0.9V ~ 10.0V
: -40℃～+85℃
=3.0V
DD
OUT
=3V
=2.0V
DD
OUT
=2.0V
■TYPICAL APPLICATION CIRCUIT
●C type circuit
54
(TOP VIEW)
SOT-25
23
1
+
SD
CL
(Tantalum)
GND
VOUT
VIN
L
CIN
+
CE
■TYPICAL PERFORMANCE
CHARACTERISTICS
C9111E331MR
L=100μH(CR54), CL47μF(Tantalum)
80
60
40
Effic iency: EFFI(% )
VIN=0.9V
20
0
0 5 0 1 00 150 2 00 250 3 00
1.5V
1.2V
Output Current:IOUT(mA)
SD: XBS104S14R-G
2.4V
3.0V
1/36
XC9110/XC9111 Series
■PIN CONFIGURATION
SOT-23 (TOP VIEW)
■PIN ASSIGNMENT
●
XC9111A/B
Lx/EXT
54
123
CE/V OUT
V OUT/V DD
SOT-25 (TOP VIEW)
PIN NUMBER
SOT-23 SOT-89
A B A B
1 1 1 1 VSS Ground
3 3 2 2 VOUT Output Voltage Montior, Internal Power Supply
2 - 3 - LX Switch
- 2 - 3 EXT External Switching transistor drive <N-ch transistor drive)
●XC9110//9111C/D/E/F
PIN NUMBER
SOT-25 USP-6C
C D E F C D E F
- - 2 2 - - 1 1 VDD Internal Power Supply
4 4 4 4 6 6 6 6 VSS Ground
- 5 - 5 - 4 - 4 EXT
5 - 5 - 4 - 4 - Lx Switch
1 1 - - 3 3 - - CE
2 2 1 1 1 1 3 3 VOUT Output voltage monitor
3 3 3 3 2,5 2,5 2,5 2,5 NC No connection
VSS
NC
USP-6C (BOTTOM VIEW)
SOT-89 (TOP VIEW)
*The dissipation pad for the USP-6C package
should be solder-plated in recommended mount
pattern and metal masking so as to enhance
mounting strength and heat release. If the pad
needs to be connected to other pins, it should be
connected to the pin No.1.
PIN NAME FUNCTIONS
PIN NAME FUNCTIONS
External switching transistor drive
<Connect to the gate pin of N-ch Power MOSFET>
Chip Enable <Connect to the V
OUT pin when Active and the
VSS pin when stand-by>
2/36
■PRODUCT CLASSIFICATION
●Selection Guide
XC9110/XC9111
Series
3/36
XC9110/XC9111 Series
■PRODUCT CLASSIFICATION
●Ordering Information
XC9110①②③④⑤⑥-⑦ : PFM control, 75% duty
XC9111①②③④⑤⑥-⑦
DESIGNATOR ITEM SYMBOL DESCRIPTION
①
②③
④
⑤⑥-⑦
(*1)
The “-G” suffix denotes Halogen and Antimony free as well as being fully RoHS compliant.
■BLOCK DIAGRAMS
●XC9111 A and B series
(*1)
Note: The XC9110 series, Tr. Built-in type, uses the Lx pin and the XC9111 series, external Tr. Type, uses the EXT pin.
The duty ratio of the XC9111 series automatically varies between 56% (oscillation frequency 180kHz) and 75%
(oscillation frequency (f
* The duty ratio depends on power supply. Please refer to the electrical characteristics on duty against output voltage
you use.
: PFM control, 56% / 75% duty variable
A VDD / V
B VDD / V
CE Function
C CE pin (5 pin) Built-in Transistor
D CE pin (5 pin) External Transistor
E VDD / V
F V
Output Voltage 15 ~ 70
Maximum Oscillation
Frequency
1 100kHz
MR
Packages
(Order Unit)
MR-G
PR
PR-G
ER
ER-G
) 100kHz). The VLx limit function only applies to the XC9110/9111 A types.
OSC
common type (for XC9111series) Built-in Transistor
OUT
common type (for XC9111series) External Transistor
OUT
separated type (5 pin) Built-in Transistor
OUT
/ V
DD
separated type (5 pin) External Transistor
OUT
ex. 3.5V output → ②= 3, ③= 5
①=A～B SOT-23 (3,000/Reel)
①=C～F SOT-25 (3,000/Reel)
①=A～B SOT-23 (3,000/Reel)
①=C～F SOT-25 (3,000/Reel)
①=A～B SOT-89 (1,000/Reel)
①=A～B SOT-89 (1,000/Reel)
①=C～F USP-6C (3,000/Reel)
①=C～F USP-6C (3,000/Reel)
4/36
■BLOCK DIAGRAMS
●XC9110 / 9111 C and D series
Note: The XC9110 series, Tr. Built-in type, uses the Lx pin and the XC9111 series, external Tr. Type, uses the EXT pin.
The XC9110 series' duty ratio is 75% and oscillation frequency (f
automatically varies between 56% (oscillation frequency 180kHz) and 75% (oscillation frequency (f
V
Lx limit function only applies to the XC9110/9111 C versions.
* The duty ratio depends on power supply. Please refer to the electrical characteristics on duty against output voltage
you use.
●XC9111 E and F series
Note: The XC9110 series, Tr. Built-in type, uses the Lx pin and the XC9111 series, external Tr. Type, uses the EXT pin.
The XC9110 / 9111 series E and F series have the V
oscillation frequency (f
56% (oscillation frequency 180kHz) and 75% (oscillation frequency (f
The V
Lx limit function only applies to the XC9110/9111 C versions.
* The duty ratio depends on power supply.
Please refer to the electrical characteristics on duty against output voltage you use.
) is 100kHz. The duty ratio of the XC9111 series
OSC
) is 100kHz. The duty ratio of the XC9111 series automatically varies between
OSC
DD pin. The XC9110 series' duty ratio is 75% and
) 100kHz).
OSC
) 100kHz). The
OSC
XC9110/XC9111
Series
5/36
XC9110/XC9111 Series
■ELECTRICAL CHARACTERISTICS
PAR AMETER SYMBOL RATINGS UNITS
VOUT Input Voltage VOUT – 0.3 ~ 12.0 V
Lx Pin Voltage VLx – 0.3 ~ 12.0 V
Lx Pin Current ILx 400 mA
EXT Pin Voltage VEXT VSS – 0.3 ~ VOUT＋0.3 V
EXT Pin Current IEXT ±100 mA
CE Input Voltage VCE – 0.3 ~ 12.0 V
VDD Input Voltage VDD – 0.3 ~ 12.0 V
SOT-23, 25 250
Power Dissipation
SOT-89 500
USP-6C
Operating Ambient Temperature Topr – 40 ~ + 85 ℃
Storage Temperature Tstg – 55 ~ +125 ℃
Pd
* Define as VSS with a standard of all the voltage.
120
mW
6/36
XC9110/XC9111
Series
■ ABSOLUTE MAXIMUM RATINGS
XC9111Axx1MR
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT
Output Voltage VOUT Connected to external components ×0.975 VOUT ×1.025 V ①
Output Voltage Temperature
Characteristics
△VOUT
△
V
OUT
・△
topr
Connected to external components
- 40℃≦Topr≦85℃
- ±100 -
Maximum Input Voltage VIN 10 - - V ①
Operating Start Voltage VST1
OUT=1mA,
Connected to external components
- 0.8 0.9 V ①
I
Oscillation Start Voltage VST2 Applied 0.8V to VOUT, Vpull=1.0V - - 0.8 V ②
Operating Hold Voltage VHLD
OUT=1mA,
Connected to external components
0.7 - - V ①
I
Input Current at No Load IIN IOUT=0mA (*1) - E1-1(*) E1-2(*) μA ①
Supply Current 1 (*2) IDD1 Applied (output voltage×0.95) to VOUT - E2-1(*) E2-2(*) μA ②
Supply Current 2 IDD2 Applied (output voltage+0.5) to VOUT - E3-1(*) E3-2(*) μA ②
Lx Switch ON Resistance RSWON Same as IDD1, VLx=0.4V (*3) - E4-1(*) E4-2(*) Ω ②
Lx Leak Current ILxL Same as IDD2, VLx＝7V - - 1 μA ③
Duty Ratio DTY Same as IDD1, measure Lx waveform E7-1(*) E7-2(*) E7-3(*) % ②
Duty Ratio 2 DTY2
Maximum Oscillation
Frequency
Maximum Oscillation
Frequency 2
MAXf
MAXf
Lx Limit Voltage (*4) VLxLMT
I
Connect to external components
Same as IDD1 85 100 115 kHz ②
OSC
Same as IDD1 153 180 207 kHz ②
OSC2
Same as I
DD1, VLx when max. oscillation
frequency is more than double
48 56 64 % ①
0.7 - 1.1 V ②
OUT=1mA, measure Lx ON time.
Efficiency (*5) EFFI Connect to external components - E8(*) - % ①
Test condition : Unless otherwise specified, V
NOTE:
*1: TOREX SBD, XBS104S14R-G is used, reverse current IR < 1μA (when reverse voltage V
parts.
*2: Supply Current 1 is the value when the IC is constantly switching. In actual operation, the oscillator periodically switches, resulting in
lower power consumption. Please refer to Input Current (I
input power supply (V
*3: Lx switch ON resistance can be calculated by (V
*4: The Lx limit voltage function becomes stable when V
*5: EFFI={[output voltage]×(output current)} / [(input voltage)×(input current)]×100
IN).
IN=VOUT×0.6, IOUT=<C1(*)>, Vpull=5.0V
R = 10V is applied), in case of using selected
IN) under no load condition for the actual current, which is supplied from the
Lx x Rp) / (Vpull - VLx). * Change Vpull so that VLx will become 0.4V.
OUT is over 2.0V.
*6: Please be aware of the absolute maximum ratings of the external components.
(*): Please refer to the charts.
ppm/
℃
Ta = 2 5 ℃
CIRCUIT
①
7/36
XC9110/XC9111 Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9111Bxx1MR
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT
Output Voltage VOUT Connected to external components ×0.975 VOUT ×1.025 V ⑥
Output Voltage
Temperature Characteristics
Maximum Input Voltage VIN 10 - - V -
Operating Start Voltage VST1
Oscillation Start Voltage VST2 Applied 0.8V to VOUT - - 0.8 V ⑦
Operation Hold Voltage VHLD
Supply Current 1 (*1) IDD1 Applied (output voltage×0.95) to VOUT - E2-1(*) E2-2(*) μA ⑦
Supply Current 2 IDD2 Applied (output voltage+0.5) to VOUT - E3-1(*) E3-2(*) μA ⑦
EXT ‘H’ ON Resistance
EXT ‘L’ ON Resistance
Duty Ratio DTY Same as IDD1, measure Lx waveform E7-1(*) E7-2(*) E7-3(*) % ⑦
Duty Ratio 2 DTY2
Maximum Oscillation
Frequency
Maximum Oscillation
Frequency 2
Efficiency (*4) EFFI Connect to external components - E9(*) - % ⑥
Test condition : Unless otherwise specified, VIN=VOUT×0.6, IOUT=<C1(*)>
NOTE:
*1: Supply Current 1 is the value when the IC is constantly switching. In actual operation, the oscillator periodically switches, resulting in
lower power consumption.
*2: EXT ‘H’ ON resistance can be calculated by (0.4 x Rp) / ( V
*3: EXT ‘L’ ON resistance can be calculated by (V
*4: EFFI={[output voltage]×(output current)} / [(input voltage)×(input current)]×100
*5: Please be aware of the absolute maximum ratings of the external components.
(*): Please refer to the charts.
△VOUT
△
V
OUT
・△topr
R
EXTH Same as IDD1, VEXT=VOUT-0.4V (*2) - E5-1(*) E5-2(*) Ω ②
R
EXTL Same as IDD1, VEXT=0.4V (*3) - E6-1(*) E6-2(*) Ω ②
MAXf
OSC
MAXf
OSC2
Connected to external components
Same as IDD1 85 100 115 kHz ⑦
Same as IDD1 153 180 207 kHz ⑦
- 40℃≦Topr≦85℃
I
OUT=1mA, Connected to external
components
I
OUT=1mA,
Connected to external components
I
OUT=1mA, measure Lx ON time.
Connect to external components
EXT – Vpull). * Change Vpull so that VEXT will become VOUT-0.4V.
EXT x Rp) / ( Vpull- VEXT). * Change Vpull so that VEXT will become 0.4V.
- ±100 -
- 0.8 0.9 V ⑥
0.7 - - V ⑥
48 56 64 % ⑥
ppm/
℃
Ta = 2 5 ℃
CIRCUIT
⑥
8/36
XC9110/XC9111
Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9110Cxx1MR, XC9111Cxx1MR
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT CIRCUIT
Output Voltage VOUT Connect to external components ×0.975 VOUT ×1.025 V ①
Output Voltage
Temperature Characteristics
△VOUT
△VOUT・△topr
Connect to external components
- 40℃≦Topr≦85℃
- ±100 -
Maximum Input Voltage VIN 10 - - V ①
Operation Start Voltage VST1
OUT=1mA, connect to external
components
- 0.8 0.9 V ①
I
Oscillation Start Voltage VST2 Applied 0.8V to VOUT, Vpull=1.0V - - 0.8 V ②
Operation Hold Voltage VHLD
OUT=1mA, connect to external
components
0.7 - - V ①
I
Input Current IIN IOUT=0mA (*1) - E1-1(*) E1-2(*) μA ①
Supply Current 1 (*2) IDD1 Applied (output voltage×0.95) to VOUT - E2-1(*) E2-2(*) μA ②
Supply Current 2 IDD2 Applied (output voltage＋0.5V) to VOUT - E3-1(*) E3-2(*) μA ②
Lx Switch ON Resistance RSWON Same as IDD1, VLx=0.4V (*3) - E4-1(*) E4-2(*) Ω ②
Lx Leak Current ILxL Same as IDD2, VLx=7V - - 1 μA ③
Duty Ratio DTY Same as IDD1, measure Lx waveform E7-1(*) E7-2(*) E7-3(*) % ②
Duty Ratio 2 DTY2
Maximum
Oscillation Frequency
Maximum
Oscillation Frequency 2
MAXf
MAXf
I
only) Connect to external components
Same as IDD1 85 100 115 kHz ②
OSC
Same as IDD1 (XC9111 only) 153 180 207 kHz ②
OSC2
48 56 64 % ①
OUT=1mA, measure Lx ON time (XC9111
Stand-by Current ISTB Same as IDD1, VCE=0V - - 0.50 μA ④
CE “High” Voltage VCEH Same as IDD1, determine Lx oscillation 0.75 - - V ④
CE “Low” Voltage VCEL Same as IDD1, determine Lx shut-down - - 0.20 V ④
CE “High” Current ICEH Same as IDD1, VCE=VOUT×0.95 - - 0.25 μA ⑤
CE “Low” Current ICEL Same as IDD1, VCE=0V - - -0.25 μA ⑤
Lx Limit Voltage (*4) VLxLMT
Same as I
DD1, when max. oscillation
frequency is more than double.
0.7 - 1.1 V ②
Efficiency (*5) EFFI Connect to external components - E8(*) - % ①
Test condition : Unless otherwise specified, connect CE to VOUT, VIN=VOUT×0.6, IOUT=<C1(*)>, Vpull=5.0V
NOTE:
*1: TOREX SD, XBS104S14R-G is used, reverse current IR < 1μA (when reverse voltage V
parts.
*2: Supply Current 1 is the value when the IC is constantly switching. In actual operation, the oscillator periodically switches, resulting in
lower power consumption. Please refer to Input Current (I
input power supply (V
*3: Lx switch ON resistance can be calculated by (V
*4: The Lx. limit voltage function becomes stable when V
*5: EFFI={[output voltage]×(output current)} / [(input voltage)×(input current)]×100
IN).
Lx x Rp) / (Vpull - VLx). * Change Vpull so that VLx will become 0.4V.
IN) under no load condition for the actual current, which is supplied from the
OUT of the XC9110/9111 series is over 2.0V.
R = 10V is applied), in case of using selected
*6: Please be aware of the absolute maximum ratings of the external components.
(*): Please refer to the charts.
ppm/
℃
Ta = 2 5 ℃
①
9/36
XC9110/XC9111 Series
■ELECTRICAL CHARACTERISTICS (Continued）
XC9110Dxx1MR, XC9111Dxx1MR
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT CIRCUIT
Output Voltage VOUT Connect to external components ×0.975 VOUT ×1.025 V ⑥
Output Voltage
Temperature Characteristics
Maximum Input Voltage VIN 10 - - V -
Operation Start Voltage VST1
Oscillation Start Voltage VST2 Applied 0.8V to VOUT - - 0.8 V ⑦
Operation Hold Voltage VHLD
Supply Current 1 (*1) IDD1 Applied (output voltage×0.95) to VOUT - E2-1(*) E2-2(*) μA ⑦
Supply Current 2 IDD2 Applied (output voltage＋0.5V) to VOUT - E3-1(*) E3-2(*) μA ⑦
EXT H ON Resistance REXTH Same as IDD1, VEXT=VOUT-0.4(*2) - E5-1(*) E5-2(*) Ω ②
EXT L ON Resistance REXTL Same as IDD1, VEXT=0.4V(*3) - E6-1(*) E6-2(*) Ω ②
Duty Ratio DTY Same as IDD1, measure Lx waveform E7-1(*) E7-2(*) E7-3(*) % ⑦
Duty Ratio 2 DTY2
Maximum Oscillation
Maximum Oscillation
Standby Current ISTB Same as IDD1, VCE=0V - - 0.50 μA ⑤
CE “High” Voltage VCEH Same as IDD1, determine Lx oscillation 0.75 - - V ⑧
CE “Low” Voltage VCEL Same as IDD1, determine Lx shut-down - - 0.20 V ⑧
CE “High” Current ICEH Same as IDD1, VCE=VOUT×0.95 - - 0.25 μA ⑤
CE “Low” Current ICEL Same as IDD1, VCE=0V - - -0.25 μA ⑤
Efficiency (*4) EFFI Connect to external components - E9(*) - % ⑥
Test condition : Unless otherwise specified, connect CE to VOUT, VIN=VOUT×0.6, IOUT=<C1(*)>
NOTE:
*1: "Supply Current 1" is the value when the IC is constantly switching. In actual operation, the oscillator periodically switches, resulting in lower
power consumption.
*2: EXT H ON resistance can be calculated by (0.4 x Rp) / (V
*3: EXT L ON resistance can be calculated by (V
*4: EFFI={[output voltage]×(output current)} / [(input voltage)×(input current)]×100
*5: Please be aware of the absolute maximum ratings of the external components.
(*): Please refer to the charts.
△VOUT
△VOUT・△topr
MAXf
MAXf
Same as IDD1 85 100 115 kHz ⑦
OSC
OSC2
Connect to external components
- 40℃≦Topr≦85℃
I
OUT=1mA, connect to external
I
OUT=1mA, connect to external
OUT=1mA, measure Lx ON time (XC9111
I
only) Connect to external components
Same as IDD1 (XC9111 only) 153 180 207 kHz ⑦
EXT x Rp) / (Vpull - VEXT). * Change Vpull so that VEXT will become 0.4V.
components
components
EXT - Vpull). * Change Vpull so that VEXT will become VOUT-0.4V.
- ±100 -
- 0.8 0.9 V ⑥
0.7 - - V ⑥
48 56 64 % ⑥
ppm/
℃
Ta = 2 5 ℃
⑥
10/36
XC9110/XC9111
Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9110Exx1MR, XC9111Exx1MR
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT CIRCUIT
Output Voltage VOUT Connect to external components ×0.975 VOUT ×1.025 V ①
Output Voltage
Temperature Characteristics
△V
OUT
△VOUT・△topr
Maximum Input Voltage VIN 10 - - V -
Operation Start Voltage VST1
Oscillation Start Voltage VST2 Applied 0.8V to VOUT, Vpull=1.0V - - 0.8 V ②
Operation Hold Voltage VHLD
Input Current IIN IOUT=0mA (*1) - E1-1(*) E1-2(*) μA ①
Supply Current 1 (*2) IDD1 Applied (output voltage×0.95) to VOUT - E2-1(*) E2-2(*) μA ②
Supply Current 2 IDD2 Applied (output voltage＋0.5V) to VOUT - E3-1(*) E3-2(*) μA ②
Lx Switch ON Resistance RSWON Same as IDD1, VLx=0.4V (*3) - E4-1(*) E4-2(*) Ω ②
Lx Leak Current ILxL Same as IDD2, VLx=7V - - 1 μA ③
Duty Ratio DTY Same as IDD1, measure Lx waveform E7-1(*) E7-2(*) E7-3(*) % ②
Duty Ratio 2 DTY2
Maximum Oscillation
Maximum Oscillation
MAXf
MAXf
OSC
OSC2
Lx Limit Voltage (*4) VLxLMT
Efficiency (*5) EFFI Connect to external components - E8(*) - % ①
Test condition : Unless otherwise specified, connect VDD to VOUT, VIN=VOUT×0.6, IOUT=<C1(*)>, Vpull=5.0V
NOTE:
*1: TOREX SD, XBS104S14R-G is used; reverse current IR < 1μA (when reverse voltage V
selected parts.
*2: "Supply Current 1" is the value when the IC is constantly switching. In actual operation, the oscillator periodically switches, resulting
in lower power consumption. Please refer to Input Current (I
from the input power supply (V
IN).
*3: Lx switch ON resistance can be calculated by (V
*4: The Lx limit voltage function becomes stable when V
*5: EFFI={[output voltage]×(output current)} / [(input voltage)×(input current)]×100
*6: When using V
The IC operates from V
DD and VOUT separately, please set the voltage range of VDD from 1.5V to 10V.
DD=0.8V, but output voltage and oscillation frequency will be stable when VDD=1.5V or more.
*7: Please be aware of the absolute maximum ratings of the external components.
(*): Please refer to the charts.
Connect to external components
- 40℃≦Topr≦85℃
I
OUT=1mA, connect to external
components
I
OUT=1mA, connect to external
components
OUT=1mA, measure Lx ON time (XC9111
I
only) Connect to external components
- ±100 -
- 0.8 0.9 V ①
0.7 - - V ①
48 56 64 % ①
Same as IDD1 85 100 115 kHz ②
Same as IDD1 (XC9111 only) 153 180 207 kHz ②
Same as I
DD1, VLx when max. oscillation
frequency is more than double.
IN) under no load condition for the actual current, which is supplied
Lx x Rp) / (Vpull - VLx). * Change Vpull so that VLx will become 0.4V.
OUT of the XC9110/9111 series is over 2.0V.
0.7 - 1.1 V ②
R = 10V is applied), in case of using
ppm/
℃
Ta = 2 5 ℃
①
11/36
XC9110/XC9111 Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9110Fxx1MR, XC9111Fxx1MR
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT CIRCUIT
Output Voltage VOUT Connect to external components ×0.975 VOUT ×1.025 V ⑥
△
V
OUT
Output Voltage
Temperature Characteristics
△
V
OUT
・△
topr
Maximum Input Voltage VIN 10 - - V
Operation Start Voltage VST1
Oscillation Start Voltage VST2 Applied 0.8V to VOUT - - 0.8 V ⑦
Operation Hold Voltage VHLD
Supply Current 1 (*1) IDD1 Applied (output voltage×0.95) to VOUT - E2-1(*) E2-2(*) μA ⑦
Supply Current 2 IDD2 Applied (output voltage＋0.5V) to VOUT - E3-1(*) E3-2(*) μA ⑦
EXT H ON Resistance REXTH Same as IDD1, VEXT=VOUT=-0.4V (*2) - E5-1(*) E5-2(*) Ω ②
EXT L ON Resistance REXTL Same as IDD1, VEXT=0.4V (*3) - E6-1(*) E6-2(*) Ω ②
Duty Ratio DTY Same as IDD1, measure Lx waveform E7-1(*) E7-2(*) E7-3(*) % ⑦
Duty Ratio 2 DTY2
Maximum Oscillation
Maximum Oscillation
MAXf
MAXf
Same as IDD1 85 100 115 kHz ⑦
OSC
2 Same as IDD1 (XC9111 only) 153 180 207 kHz ⑦
OSC
Efficiency (*4) EFFI Connect to external components - E9(*) - % ⑥
Test condition : Unless otherwise specified, connect VDD to VOUT, VIN=VOUT×0.6, IOUT=<C1(*)>
NOTE:
*1: "Supply Current 1" is the value when the IC is constantly switching. In actual operation, the oscillator periodically switches, resulting
in lower power consumption.
*2: EXT H ON resistance can be calculated by (0.4 x Rp) / (V
*3: EXT L ON resistance can be calculated by (V
*4: EFFI={[output voltage]×(output current)} / [(input voltage)×(input current)]×100
*5: When using V
The IC operates from V
DD and VOUT separately, please set the voltage range of VDD from 1.5V to 10V.
DD=0.8V, but output voltage and oscillation frequency will be stable when VDD=1.5V or more.
*6: Please be aware of the absolute maximum ratings of the external components.
(*): Please refer to the charts.
Connect to external components
- 40℃≦Topr≦85℃
I
OUT=1mA, connect to external
components
I
OUT=1mA, connect to external
components
OUT=1mA, measure Lx ON time
I
(XC9111 only) Connect to external
EXT - Vpull). * Change Vpull so that VEXT will become VOUT-0.4V.
EXT x Rp) / (Vpull - VEXT). * Change Vpull so that VEXT will become 0.4V.
- ±100 -
- 0.8 0.9 V ⑥
0.7 - - V ⑥
48 56 64 % ⑥
ppm/
℃
Ta = 2 5 ℃
⑥
-
12/36
XC9110/XC9111
■ELECTRICAL CHARACTERSTICS (Continued)
● IDD2, REXTH, REXTL, DTY Chart
SYMBOL E2-1 E2-2 E1-1 E1-2 E3-1 E3-2 E4-1 E4-2 E5-1 E5-2 E6-1 E6-2
PAR AMETER Supply Current 1
UNIT (μA) (μA) (μA) (Ω) (Ω) (Ω)
SETTING
VOLTAGE
1.5 7.7 15.1
1.6 8.0 15.6
1.7 8.3 16.2
1.8 8.6 16.8
1.9 8.9 17.5
2.0 9.3 18.2
2.1 9.7 18.9
2.2 10.1 19.7
2.3 10.5 20.6
2.4 11.0 21.5
2.5 11.5 22.5
2.6 12.0 23.5
2.7 12.5 24.5
2.8 13.1 25.6
2.9 13.7 26.8
3.0 14.3 28.0
3.1 15.0 29.3
3.2 15.7 30.6
3.3 16.4 31.9
3.4 17.1 33.3
3.5 17.8 34.8
3.6 18.6 36.3
3.7 19.4 37.9
3.8 20.3 39.5
3.9 21.1 41.1
4.0 22.0 42.8
4.1 22.9 44.5
4.2 23.8 46.3
4.3 24.8 48.2
4.4 25.7 50.0
4.5 26.7 52.0
4.6 27.7 53.9
4.7 28.8 56.0
4.8 29.8 58.0
4.9 30.9 60.1
5.0 31.7 63.4
5.1 32.3 64.7
5.2 32.9 65.9
5.3 33.5 67.1
5.4 34.1 68.3
5.5 34.7 69.5
5.6 35.3 70.7
5.7 36.0 72.0
5.8 36.5 73.1
5.9 37.1 74.3
6.0 37.7 75.5
6.1 38.4 76.8
6.2 38.9 77.9
6.3 39.5 79.1
6.4 40.2 80.4
6.5 40.8 81.6
6.6 41.3 82.7
6.7 42.0 84.0
6.8 42.6 85.2
6.9 43.2 86.4
7.0 43.7 87.5
IDD1 IIN IDD2 RSWON REXTH REXTL
TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX.
Input Current
(No Load)
4.3 8.6 1.9
4.4 8.8 4.0
4.5 9.1
4.6 9.3 4.2
4.7 9.5
4.8 9.7 4.4
5.0 10.0
5.1 10.2 4.6
5.2 10.4
5.3 10.6 4.8
5.4 10.8
5.5 11.1 5.0
5.6 11.3
5.7 11.5 5.2
5.8 11.7
6.0 12.0 2.7 5.4
Supply Current 2
3.5
3.9
2.0
4.1
2.1
4.3
2.2
4.5
2.3
4.7
2.4
4.9
2.5
5.1
2.6
5.3
Lx Switch
ON Resistance
4.2 6.3 160 240 67 101
3.5 5.3 108 162 52 78
3.2 4.8 91 137 45 68
2.8 4.2 70 105 38 57
2.5 3.8 59 89 33 50
2.1 3.2 40 60 24 36
EXT H
ON Resistance
ON Resistance
Series
EXT L
13/36
XC9110/XC9111 Series
■ELECTRICAL CHARACTERSTICS (Continued)
● IOUT, DTY, EFFI Chart
SYMBOL C1 E7-1 E7-2 E7-3 E8 E9
PAR AMETER
UNIT (mA) (%) (%)
SETTING
VOLTAGE
OUTPUT
CURRENT
IOUT
1.5 7.5
1.6 8.0
1.7 8.5
1.8 9.0
1.9 9.5
2.0 10.0
2.1 10.5
2.2 11.0
2.3 11.5
2.4 12.0
2.5 12.5
2.6 13.0
2.7 13.5
2.8 14.0
2.9 14.5
3.0 30.0
3.1 31.0
3.2 32.0
3.3 33.0
3.4 34.0
3.5 35.0
3.6 36.0
3.7 37.0
3.8 38.0
3.9 39.0
4.0 40.0
4.1 41.0
4.2 42.0
4.3 43.0
4.4 44.0
4.5 45.0
4.6 46.0
4.7 47.0
4.8 48.0
4.9 49.0
5.0 50.0
5.1 51.0
5.2 52.0
5.3 53.0
5.4 54.0
5.5 55.0
5.6 56.0
5.7 57.0
5.8 58.0
5.9 59.0
6.0 60.0
6.1 61.0
6.2 62.0
6.3 63.0
6.4 64.0
6.5 65.0
6.6 66.0
6.7 67.0
6.8 68.0
6.9 69.0
7.0 70.0
MIN. TYP. MAX. TYP.
DUTY RATIO
DTY EFFI
70 75 80
68 73 78
XC9110 XC9111 XC9110 XC9111
60 75 60 75
65 79 61 75
77 82 77 82
80 86 80 83
82 88 82 85
EFFICIENCY
14/36
XC9110/XC9111
■TYPICAL APPLICATION CIRCUITS
●A type circuit ●B type circuit
L: 100μH (Coil, CR54, SUMIDA) L: 47μH (Coil, CR54, SUMIDA)
SD: XBS104S14R-G (Schottky type, TOREX) SD: XBS104S14R-G (Schottky type, TOREX)
CL: 16V, 47μF (Tantalum) CL: 16V, 47μF (Tantalum)
CIN: 16V, 47μF (Tantalum) CIN: 16V, 47μF (Tantalum)
RB: 500Ω
CB: 2200pF
Tr: 2SD1628
●C type circuit ●D type circuit
L: 100μH (Coil, CR54,SUMIDA)
SD: XBS104S14R-G (Schottky type, TOREX)
C
L: 16V, 47μF (Tantalum)
IN: 16V, 47μF (Tantalum)
C
●E type circuit
L: 100μH (Coil, CR54,SUMIDA)
SD: XBS104S14R-G (Schottky type, TOREX)
CL: 16V, 47μF (Tantalum)
C
IN: 16V, 47μF (Tantalum)
L: 47μH (Coil, CR54,SUMIDA)
SD: XBS104S14R-G (Schottky type, TOREX)
C
L: 16V, 47μF (Tantalum)
IN: 16V, 47μF (Tantalum)
C
R
B: 500Ω
C
B: 2200pF
Tr: 2SD1628 (SANYO)
●F type circuit
L: 47μH (Coil, CR54,SUMIDA)
SD: XBS104S14R-G (Schottky type, TOREX)
L: 16V, 47μF (Tantalum)
C
C
IN: 16V, 47μF (Tantalum)
R
B: 1kΩ
B: 3300pF
C
Tr: 2SD1628 (SANYO)
Series
15/36
XC9110/XC9111 Series
■OPERATIONAL EXPLANATION
The XC9110/9111 series are PFM controlled step-up DC/DC converter (A, C and E types) / controller ICs (B, D and F
types), which contain voltage reference source, PFM comparator, duty selector, PFM controlled OSC, VLx Limiter, driver
transistor and so on. With the XC9110 series, maximum duty ratio is set to 75% (maximum oscillation
frequency=MAXf
switches duty ratio between 56% (MAXf
can support both large and small currents.
<Reference Voltage Source (Vref) >
The reference voltage source provides the reference voltage to ensure stable output voltage of the DC/DC converter.
< PFM Comparator >
The PFM comparator compares the feedback voltage divided by the internal split resistors with the internal reference
voltage. When the feedback voltage is higher than the reference voltage, PFM controlled OSC will be stopped. When
the feedback voltage is lower than the reference voltage, the PFM controlled OSC will be operated so that the output
voltage will be stable by sending a signal to the buffer drive circuit and controlling the internal or external driver transistor.
< Duty Selector >
With the XC9111 series, the duty selector automatically switches duty ratio between 56% and 75% when it senses
changes in load and can support both large and small currents.
< PFM Controlled Oscillator >
The PFM controlled OSC determines maximum oscillation frequency. The circuit generates the oscillation frequency of
100kHz at 75% duty and 180kHz at 56%.
< V
Lx Limiter>
The V
Lx circuit of the XC9110/9111 A, C and D types detects in-rush current and overcurrent, which flows from the VOUT
pin to the Lx pin during short-circuit. In overcurrent, the driver transistor will be OFF. When the overcurrent state is
eliminated, the IC resumes its normal operation.
<Chip Enable Function>
The chip enable function of the XC9110/9111 C and D types enables the IC to be in shut down mode when a low level
signal is input to the CE pin. During the shut down mode, the current consumption will be reduced to 0.5μA (MAX.).
<Separated V
With the separated V
: 100kHz) making it suitable for use with large current operations. The XC9111 series automatically
OSC
: 180kHz) and 75% (MAXf
OSC
DD/VOUT>
DD pin, the XC9110/9111 E and F types can be operated in both low and high voltage.
: 100kHz) when it senses changes in load and
OSC
16/36
XC9110/XC9111
Series
■EXTERNAL COMPONENTS
Tr.: *Using a MOSFET
XP151A13A0MR-G (N-ch Power MOSFET, TOREX)
Note : V
so please be careful with the power supply voltage.
If the power supply voltage is over 6V, Please use the
XP151A12A2MR-G with a V
●RB value example (when using NPN Transistor)
GS breakdown voltage of this Transistor is 8V
GS breakdown voltage of 12V.
VOUT (V) IOUT (mA) VIN (V)
RB (Ω)
1.8 10 1.2 4.5 3.3 5 1.2 6.5
1.8 10 1.5 6.0 3.3 5 1.5 6.5
1.8 30 1.2 2.0 3.3 10 1.2 5.0
1.8 30 1.5 2.0 3.3 10 1.5 4.5
1.8 50 1.2 1.2 3.3 30 1.2 3.5
1.8 50 1.5 1.5 3.3 30 1.5 3.5
* Tr.: 2SD1628
SD: XBS104S14R-G (TOREX)
MA2Q735 (MATSUSHITA)
L: 16V, 47μF (Tantalum type, KYOCERA TAJ)
C
CIN: 16V, 47μF (Tantalum type, KYOCERA TAJ)
16V, 220μF (Electrolytic Capacitor)
L: <XC9110/9111A, C and E series (Transistor built-in)> <XC9110/9111B, D and F series(Transistor external)>
100μH (CR54,SUMIDA) 22μH, 47μH (CR54, SUMIDA)
100μH (CDRH6D28,SUMIDA)
■NOTES ON USE
1. Please do not exceed the value of stated absolute maximum ratings.
2. The DC/DC converter / controller IC's performance is greatly influenced by not only the ICs' characteristics, but also by
those of the external components. Care must be taken when selecting the external components.
3. The Lx limit voltage function becomes stable when V
XC9110/9111E series is over 2.0V.
4. Make sure that the PCB GND traces are as thick as possible, as variations in ground potential caused by high ground
currents at the time of switching may result in instability of the IC.
5. Please mount each external component as close to the IC as possible and use thick, short connecting traces to reduce
the circuit impedance.
* Using a NPN Transistor
2SD1628 (SANYO)
R
B: 500Ω (Adjust in accordance with load and Tr’s hFE.)
C
B: 2200pF (Ceramic)
C
B
≦
1 / ( 2TT x RB x FOSC x 0.7 )
VOUT (V) IOUT (mA) VIN (V)
OUT of the XC9110/9111C series is over 2.0V and the VDD of the
RB (Ω)
17/36
p
XC9110/XC9111 Series
■TEST CIRCUITS
Circuit ①
Circuit ②
Circuit ③
Circuit ④
<External Com
Circuit ①
C
IN: 47μF, 16V (Tantalum)
L: CR54, 100μH (SUMIDA)
SD: XBS104S14R-G (Schottky, TOREX)
L: 47μF, 16V (Tantalum)
C
Circuit②
Rp: 300Ω
Rp: 10Ω (For Lx ON Resistance
Rp: 200Ω
Cp: 100μF (OS-CON, SANYO)
onents>
and measuring Lx Limit Current)
(For measuring EXT ON Resistance)
Circuit ⑤
Circuit ⑥
Circuit ⑦
Circuit ⑧
Circuit ④
Cp: 100μF (OS-CON, SANYO)
Circuit ⑥
IN: 47μF, 16V (Tantalum)
C
L: CR54, 100μH (SUMIDA)
Tr: 2SD1628 (SANYO)
B: 2200pF
C
B: 500Ω
R
SD: XBS104S14R-G (Schottky, TOREX)
L: 47μF, 16V (Tantalum)
C
18/36
■TYPICAL PERFORMANCE CHARACTERISTICS
(1) Output Voltage vs. Output Current
2
XC9111E181MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
XC9110E181MR
L=100uH(CR 54),C L:47uF (Tantalum)
2
SD:XBS104S14R
(V)
(V)
1.9
OUT
1.8
1.7
1.6
Output Voltage:V
VIN=0.9V
1.2V
1.5
0 20406080100
Output Current:I
OUT
(mA)
1.5V
1.9
OUT
1.8
1.7
VIN=0.9V
1.6
Output Voltage: V
1.5
0 20 40 60 80 100
Output Current:I
3.5
(V)
3
OUT
2.5
2
XC9111E331MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
3.0V
2.4V
1.5V
1.2V
3.5
(V)
3
OUT
2.5
2
XC9110E331MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
1.2V
VIN=0.9V
Output Voltage:V
VIN=0.9V
1.5
1
0 50 100 150 200 250 300
Output Current:I
OUT
(mA)
1.5
Output Voltage: V
1
0 50 100 150 200 250 300
Output Current:I
5.1
(V)
5
OUT
4.9
4.8
4.7
Output Voltage: V
4.6
XC9111E501MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
2.7V
3.3V
VIN=1.5V
0 50 100 150 200 250 300
Output Current:I
OUT
4.2V
(mA)
5.1
(V)
5
OUT
4.9
4.8
4.7
Output Voltage: V
4.6
XC9110E501MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
VIN=1.5V
0 50 100 150 200 250 300
Output Current:I
1.2V 1.5V
1.5V
2.7V 3.3V
OUT
OUT
OUT
(mA)
(mA)
(mA)
XC9110/XC9111
Series
*Topr = 25℃
3.0V
2.4V
4.2V
19/36
XC9110/XC9111 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(1) Output Voltage vs. Output Current (Continued)
2.0
1.9
(V)
OUT
1.8
1.7
1.6
Output Voltage:V
1.5
5.1
5.0
(V)
OUT
4.9
4.8
4.7
Output Voltage:V
4.6
XC9111F181MR
L=22uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R, Tr:XP151A13A0M
1.5V
VIN=1.2V
0 100 200 300 400
Output Current:I
XC9111F501MR
L=22uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R, Tr:XP151A12A2M
0 100 200 300 400
Output Current:I
(mA)
OUT
2.7V
VIN=2.4V
(mA)
OUT
3.3V
3.8
3.6
(V)
OUT
3.4
3.2
3.0
Output Voltage:V
2.8
2.0
1.9
(V)
OUT
1.8
1.7
1.6
Output Voltage:V
1.5
XC9111F331MR
L=22uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R, Tr:XP151A13A0M
3.0V
OUT
OUT
2.4V
(mA)
1.5V
(mA)
VIN=1.5V
0 100 200 300 400
Output Current:I
XC9111F181MR
L=22uH(CR 54),C L:47uF (Tantalum), CB: 2200pF
SD:XBS104S14R, Tr:2SD1628, RB: 100omh
VIN=0.9V 1.2V
0 100 200 300 400
Output Current:I
*Topr = 25℃
20/36
)
)
)
)
)
)
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(2) Efficiency vs. Output Current
100
80
XC9111E181MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
100
80
XC9110E181MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
60
VIN=0.9V
40
Efficiency:EFFI(%
20
0
0 20406080100
Output Current:I
1.2V
OUT
(mA)
1.5V
60
40
Efficiency:EFFI(%
20
VIN=0.9V
1.2V
0
0 20 40 60 80 100
Output Current:I
OUT
1.5V
(mA)
100
XC9111E331MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
100
XC9110E331MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
80
3.0V
60
40
VIN=0.9V
Efficiency:EFFI(%
20
1.5V
1.2V
2.4V
80
60
40
Efficiency:EFFI(%
VIN=0.9V
20
1.5V
1.2V
3.0V
2.4V
0
0 50 100 150 200 250 300
Output Current:I
OUT
(mA)
0
0 50 100 150 200 250 300
Output Current:I
OUT
(mA)
100
80
60
XC9111E501MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
VIN=1.5V
2.7V 3.3V
4.2V
100
80
60
XC9110E501MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
3.3V
VIN=1.5V
2.7V
4.2V
40
Efficiency:EFFI(%
20
0
0 50 100 150 200 250 300
Output Current:I
OUT
(mA)
40
Efficiency:EFFI(%
20
0
0 50 100 150 200 250 300
Output Current:I
OUT
(mA)
XC9110/XC9111
Series
*Topr = 25℃
21/36
)
)
)
)
XC9110/XC9111 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(2) Efficiency vs. Output Current (Continued)
100
80
60
40
Efficiency:EFFI(%
20
0
XC9111F181MR
L=22uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R,Tr:XP151A13A0M
1.5V
VIN=1.2V
0 100 200 300 400
Output Current:I
OUT
(mA)
100
80
60
40
Efficiency:EFFI(%
20
0
100
80
60
40
Efficiency:EFFI(%
20
0
XC9111F501MR
L=22uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R,Tr:XP151A12A2M
2.7V,3.3V
VIN=2.4V
0 100 200 300 400
Output Current:I
OUT
(mA)
100
80
60
40
Efficiency:EFFI(%
20
0
XC9111F331MR
L=22uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R,Tr:XP151A13A0M
3.0V
OUT
2.4V
(mA)
VIN=1.5V
0 100 200 300 400
Output Current:I
XC9111F181MR
L=22uH(CR 54),C L:47uF (Tantalum),CB:2200pF
SD:XBS104S14R,Tr:2SD 1628,R B:100ohm
1.5V
VIN=0.9V 1.2V
0 100 200 300 400
Output Current:I
OUT
(mA)
*Topr = 25℃
22/36
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(3) Ripple Voltage vs. Output Current
120
100
80
60
40
Ripple Voltage:Vr(mV)
20
0
120
100
80
60
40
Ripple Voltage:Vr(mV)
20
0
120
100
80
60
40
Ripple Voltage:Vr(mV)
20
0
XC9111E181MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
1.2V
1.5V
VIN=0.9V
0 20406080100
Output Current:I
XC9111E331MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
1.5V 2.4V
1.2V
VIN=0.9V
0 50 100 150 200 250 300
Output Current:I
XC9111E501MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
2.7V
VIN=1.5V
0 50 100 150 200 250 300
Output Current:I
OUT
OUT
3.3V
OUT
(mA)
3.0V
(mA)
4.2V
(mA)
XC9110E181MR
L=100uH(CR 54),C L:47uF (Tantalum)
120
100
80
60
40
Ripple Voltage:Vr(mV)
20
0
0 20406080100
140
120
100
80
60
40
Ripple Voltage:Vr(mV)
20
0
0 50 100 150 200 250 300
120
100
80
60
40
Ripple Voltage:Vr(mV)
20
0
0 50 100 150 200 250 300
SD:XBS104S14R
1.2V 1.5V
VIN=0.9V
Output Current:I
XC9110E331MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
1.5V
1.2V
VIN=0.9V
Output Current:I
XC9110E501MR
L=100uH(CR 54),C L:47uF (Tantalum)
SD:XBS104S14R
2.7V
VIN=1.5V
Output Current:I
OUT
3.0V
OUT
OUT
(mA)
2.4V
(mA)
3.3V
(mA)
4.2V
XC9110/XC9111
Series
*Topr = 25℃
23/36
XC9110/XC9111 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(3) Ripple Voltage vs. Output Current (Continued)
250
200
150
100
50
Ripple Voltage:Vr(mV)
0
250
200
150
100
50
Ripple Voltage:Vr (mV)
0
XC9111F181MR
L=22uH(CR54),CL:47uF(Tantalum )
SD:XBS104S14R,Tr:XP151A13A0M
VIN=1.2V
0 100 200 300 400
Output Current:I
XC9111F501MR
L=22uH(CR54),CL:47uF(Tantalum )
SD:XBS104S14R,Tr:XP151A12A2M
0 100 200 300 400
Output Current:I
OUT
VIN=2.4V
OUT
1.5V
(mA)
3.3V
2.7V
(mA)
250
200
150
100
50
Ripple Voltage:Vr(mV)
0
350
300
250
200
150
100
Ripple Voltage:Vr ( mV)
50
0
XC9111F331MR
L=22uH(CR54),CL:47uF(Tantalum )
SD:XBS104S14R,Tr:XP151A13A0M
2.4V
3.0V
VIN=1.5V
0 100 200 300 400
Output Current:I
XC9111F181MR
L=22uH(CR54),CL:47uF(Tantalum ),C B:2200pF
SD:XBS104S14R,Tr:2SD 1628,RB:100ohm
VIN=0.9V
0 100 200 300 400
Output Current:I
1.2V
OUT
OUT
(mA)
1.5V
(mA)
*Topr = 25℃
24/36
C
C
C
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(4) Supply Current 1 vs. Output Voltage (5) Supply Current 2 vs. Output Voltage
80
70
1(uA)
60
DD
50
40
30
20
10
Supply Current1: I
0
1.5 2.5 3.5 4.5 5.5 6.5
XC9111E**1
O
25
-40
C
O
C
O
Topr=85
Output Voltage:V
VDD=V
OUT
(V)
OUT
×0.95
5
4.5
4
2(uA)
3.5
DD
3
2.5
2
1.5
1
Supply Curr ent2: I
0.5
0
1.5 2.5 3.5 4.5 5.5 6.5
(6) Stand-by Current vs. Output Voltage
(7) No Load Input Current vs. Output Voltage
0.5
0.45
0.4
0.35
0.3
0.25
0.2
0.15
0.1
0.05
Stand-by Current: ISTB(uA)
0
1.5 2.5 3.5 4.5 5.5 6.5
XC9111C**1
85OC
Output Voltage:V
Topr= 25
(V)
OUT
O,
-40OC
80
uA)
70
（
60
50
40
30
20
10
No-Load Input Current: IIN
0
(8) Lx Limit Voltage vs. Output Voltage
XC9111E**1
V DD=V
OUT
OUT
×
O
C
O
C
O
(V)
1.1
1
0.9
0.8
Topr=85
25
0.7
Lx Limit Voltage: VLxLMT(V)
0.6
-40
234567
Output Voltage:V
0.95
(9) Lx Switch-ON Resistance vs. Output Voltage
)
Ω
(
SWON
Lx Switch-ON
Resistance:R
* The reason for the increase in the "no load input current" figure at Ta=85℃ in the performance characteristics is
because of an increase in the reverse current of the Schottky diode and not because of abnormalities of the IC
itself.
XC9111E**1
V DD=V
OUT+
O
Topr=85
Output Voltage:V
XC9111E**1
L=100uH(CR 54),C L:47uF(Tantalum)
SD: XBS104S14R
85
VIN=V
1.5 2.5 3.5 4.5 5.5 6.5
Output Voltage:V
XC9111E∗∗1
7
6
5
4
3
2
1
0
1.5 2.5 3.5 4.5 5.5 6.5
Output Voltage:V
25
-40
O
C
×0.6
OUT
C
O
C
O
V DD=V
(V)
OUT
Topr= 25
O
-40
(V)
OUT
×0.95,VLx=0.4V
OUT
Topr=85OC
25
-40
(V)
OUT
O
C
C
O
C
O
C
XC9110/XC9111
Series
*Topr = 25℃
0.5
25/36
XC9110/XC9111 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(10) EXT H ON Resistance vs. Output Voltage (11) EXT L ON Resistance vs. Output Voltage
(12) Maximum Oscillation Frequency 1. vs. Output Voltage
(14) Duty Ratio 1 vs. Output Voltage (15) Duty Ratio 2 vs. Output Voltage
(13) Maximum Oscillation Frequency 2 vs. Output Voltage
*Topr = 25℃
26/36
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(16) Output Voltage vs. Ambient Temperature (17) CE “H”, “L” Voltage vs. Output Voltage
3.5
(V)
3.4
OUT
3.3
3.2
3.1
Output Voltage: V
3
-50 -20 10 40 70 100
(18) Operation Start Voltage vs. Ambient Temperature (19) Oscillation Start Voltage vs. Ambient Temperature
1
(V)
0.9
ST1
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
Operation Start Voltage:V
0
-50 -20 10 40 70 100
(20) Operation Hold Voltage vs. Ambient Temperature
0.6
0.5
(V)
0.4
HLD
0.3
0.2
Voltage:V
Operation Holding
0.1
0
-50 -20 10 40 70 100
XC9111E331
VIN=1.98V
IOUT=3 0mA
o
I
OUT
C)
=1.0mA
o
C)
Ambient Temp:Ta(
XC9111E331
L=100uH(CR54), CL=47uF (Tantalum)
SD:XBS104S14R
Ambient Temp:Ta(
XC9111E331
I
=1.0mA
OUT
Ambient Temp:(
o
C)
XC9111C∗∗1
0.80
0.70
(V)
0.60
CEH,L
0.50
0.40
0.30
85
O
0.20
0.10
CE "H","L"Voltage:V
0.00
1.5 2.5 3.5 4.5 5.5 6.5
Output Voltage:V
VDD=V
-40OC
C
Topr =2 5
OUT
XC9111E331
1
(V)
0.9
ST2
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
Osillation Start Voltage:V
0
-50 -20 10 40 70 100
Ambient Temp:Ta(
VOUT=0.8V
×0.95
OUT
O
C
(V)
o
C)
XC9110/XC9111
Series
*Topr = 25℃
27/36
XC9110/XC9111 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(21) Load Transient Response
VIN=2.4V, VDD=VOUT, IOUT=0.1mA 50mA
*Topr = 25℃
28/36
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(22) Input Transient Response
XC9110/XC9111
Series
*Topr = 25℃
29/36
XC9110/XC9111 Series
■PACKAGING INFORMATION
●SOT-23
●SOT-89
+0.2
-0.1
1.6
2.8±0.2
0.2MIN
1.1±0.1
1.3MAX
●SOT-25
●USP-6C
(0.4)
2.5±0.1
1.0±0.2
(0.1)
4.0±0.25
1.5±0.1
°
5
5°
30/36
■PACKAGING INFORMATION (Continued)
XC9110/XC9111
Series
●USP-6C Reference Pattern Layout
●USP-6C Reference Metal Mask Design
31/36
XC9110/XC9111 Series
■ MARKING RULE
●SOT-23
① represents product series
MARK FUNCTIONS PRODUCT SERIES
5
6
② represents integer of output voltage and oscillation frequency
OUTPUT VOLTAGE
③ represents decimal point of output voltage and oscillation frequency
OUTPUT VOLTAGE
④ represents production lot number
0 to 9, A to Z repeated (G, I, J, O, Q, W excluded)
- Built-In Transistor XC9111Axxxxx
- External Transistor XC9111Bxxxxx
MARK
f
=100kHz
OSC
1.x 1
2.x 2
3.x 3
4.x 4
5.x 5
6.x 6
7.x 7
MARK
f
=100KHz
OSC
x.0 0
x.1 1
x.2 2
x.3 3
x.4 4
x.5 5
x.6 6
x.7 7
x.8 8
x.9 9
32/36
■ MARKING RULE (Continued)
●SOT-25
SOT-25 (TOP VIEW)
① represents product series
MARK FUNCTION PRODUCT SERIES
V CE Tr. Built-in XC9110Cxxxxx
X CE External Tr. XC9110Dxxxxx
Y VDD/VOUT Tr. Built-in XC9110Exxxxx
Z VDD/VOUT External Tr. XC9110Fxxxxx
5 CE Tr. Built-in XC9111Cxxxxx
6 CE External Tr. XC9111Dxxxxx
7 VDD/VOUT Tr. Built-in XC9111Exxxxx
8 VDD/VOUT External Tr. XC9111Fxxxxx
② represents integer of output voltage and oscillation frequency
OUTPUT VOLTAGE
1.x 1
2.x 2
3.x 3
4.x 4
5.x 5
6.x 6
7.x 7
③ represents decimal point of output voltage and oscillation frequency
OUTPUT VOLTAGE
x.0 0
x.1 1
x.2 2
x.3 3
x.4 4
x.5 5
x.6 6
x.7 7
x.8 8
x.9 9
④ represents production lot number
0 to 9, A to Z repeated (G, I, J, O, Q, W excluded)
f
f
OSC
OSC
MARK
XC9110/XC9111
Series
MARK
=100kHz
=100kHz
33/36
XC9110/XC9111 Series
■ MARKING RULE (Continued)
●SOT-89
① represents product series
MARK FUNCTIONS PRODUCT SERIES
- Built-In Transistor XC9111Axxxxx
- External Transistor XC9111Bxxxxx
5
6
② represents integer of output voltage and oscillation frequency
OUTPUT VOLTAGE
1.x 1
2.x 2
3.x 3
4.x 4
5.x 5
6.x 6
7.x 7
③ represents decimal point of output voltage and oscillation frequency
OUTPUT VOLTAGE
x.0 0
x.1 1
x.2 2
x.3 3
x.4 4
x.5 5
x.6 6
x.7 7
x.8 8
x.9 9
④ represents production lot number
0 to 9, A to Z repeated (G, I, J, O, Q, W excluded)
f
f
OSC
OSC
MARK
MARK
=100kHz
=100kHz
34/36
■ MARKING RULE (Continued)
●USP-6C
USP-6C (TOP VIEW)
① represents product series
MARK PRODUCT SERIES
M XC9110xxx1Dx
N XC9111xxx1Dx
② represents series type
MARK FUNCTION PRODUCT SERIES
C CE Tr. Built-in XC911xCxx1Dx
D CE External Tr. XC911xDxx1Dx
E VDD/VOUT Tr. Built-in XC911xExx1Dx
F VDD/VOUT External Tr. XC911xFxx1Dx
③ represents integer of output voltage
MARK OUTPUT VOLTAGE
1 1.x
2 2.x
3 3.x
4 4.x
5 5.x
6 6.x
7 7.x
④ represents decimal point of output voltage
MARK OUTPUT VOLTAGE
0 x.0
1 x.1
2 x.2
3 x.3
4 x.4
5 x.5
6 x.6
7 x.7
8 x.8
9 x.9
⑤ represents oscillation frequency
MARK OSCILLATION FREQUENCY PRODUCT SERIES
1 x.0 XC911xxxx1Dx
⑥ represents production lot number
0 to 9, A to Z repeated (G, I, J, O, Q, W excluded)
* No character inversion used
XC9110/XC9111
Series
35/36
XC9110/XC9111 Series
1. The products and product specifications contained herein are subject to change without
notice to improve performance characteristics. Consult us, or our representatives
before use, to confirm that the information in this datasheet is up to date.
2. We assume no responsibility for any infringement of patents, patent rights, or other
rights arising from the use of any information and circuitry in this datasheet.
3. Please ensure suitable shipping controls (including fail-safe designs and aging
protection) are in force for equipment employing products listed in this datasheet.
4. The products in this datasheet are not developed, designed, or approved for use with
such equipment whose failure of malfunction can be reasonably expected to directly
endanger the life of, or cause significant injury to, the user.
(e.g. Atomic energy; aerospace; transport; combustion and associated safety
equipment thereof.)
5. Please use the products listed in this datasheet within the specified ranges.
Should you wish to use the products under conditions exceeding the specifications,
please consult us or our representatives.
6. We assume no responsibility for damage or loss due to abnormal use.
7. All rights reserved. No part of this datasheet may be copied or reproduced without the
prior permission of TOREX SEMICONDUCTOR LTD.
36/36
Loading...