Toastmaster TMGT24 Parts List

Gas Griddle

Owner’s Manual

Models

TMGM24, TMGM36, TMGM48
TMGT24, TMGT36, TMGT48

This manual includes material related to installation,
use , cleaning, and care. Exploded view[s], as well
as any available parts list[s] and wiring diagram[s]
pertaining to the unit[s] covered by this manual are
also included.

This manual must be read and understood by all
persons using or installing this appliance. Contact
your Star dealer if you have any questions concerning
installation, use, or maintenance of this equipment.

DO NOT DISCARD THIS MANUAL.

TMGT36

2M-Z12966 • REV E • 06/2019

SAFETY SYMBOLS

These symbols are intended to alert the user to the

presence of important operating and maintenance

instructions in the manual accompanying the appliance.

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

This unit has been tested for proper operation before leaving our plant to ensure delivery of your unit

in perfect condition. However, there are instances in which the unit may be damaged in transit. In the
event you discover any type of damage to your product upon receipt, you must immediately contact the
transportation company who delivered the item to you and initiate your claim with that company. If this
procedure is not followed, it may affect the warranty status of the unit. If damage or loss is not apparent
until after equipment is unpacked, a request for inspection of concealed damage must be made with
carrier within 15 days. Please record the model number, serial number, voltage, and purchase date in the
area below at the time of receipt.

Model Number _______________________

Serial Number _______________________

Voltage _______________________

Purchase Date _______________________

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please have the

information in the above fi elds ready when you call to ensure a faster service.

Using any part other than genuine Toasmaster factory supplied parts relieves the manufacturer of all liability.

Due to periodic changes in designs, methods, procedures, policies, and regulations, the

specifi cations contained in this document are subject to change without notice. Toastmaster reserves the

right to change product specifi cations and design without notice. Such revisions do not entitle the

buyer to corresponding changes, improvements, additions or replacements for previously purchased
equipment. While Toastmaster exercises good faith efforts to provide information that is accurate,

we are not responsible for errors or omissions in information provided or conclusions reached as a result

of using the specifi cations. By using the information provided, the user assumes all risks in connection

with such use.

PLEASE REFER TO THE WARRANTY PAGE FOR SPECIFIC WARRANTY INFORMATION.

AUTHORIZED SERVICE AGENT LISTING

Reference the listing provided with the unit or for an updated listing go to the website or call customer

service to fi nd an agent.

Business hours: 8:00 a.m. to 4:30 p.m. Central Standard Time

Telephone: [phone]

Fax: [phone]

Email: [e-mail]

Website: www.star-mfg.com

Please visit www.starwebconnect.com/manuals.aspx for digital versions of any documents associated with

this unit.

2M-Z12966: Toastmaster TMGT Series Gas Griddles

SPECIFICATIONS: Gas Griddle

MODEL: TMGM24, TMGM36, TMGM48, TMGT24, TMGT36, TMGT48

TMGT36 shown

A

MODEL HEIGH T

2M-Z12966: Toastmaster TMGT Series Gas Griddles

TMGM24/

TMGT24

TMGM36/

TMGT36

TMGM48/

TMGT48

15.5 in.

(394 mm)

15.5 in.

(394 mm)

15.5 in.

(394 mm)

WIDTH DEPT H BTU

[A]

24 in.

(610 mm) (806 mm)

36 in.

(914 mm) (806 mm)

48 in.

(1.22 m) (806 mm)

1.2 in.

(30 mm)

31.75 in .

31.75 in .

31.75 in .

6.7 in.

(170 mm)

40,000

60,000

80,000

2 in.

(51 mm)

27.75 in.

(705 mm)

3.4 in.

(86 mm)

APPROX. SHIP APPROX. WEIGHT

WEIGHT

162 lb .

(73.5 kg )

232 lb .

(105.2 kg)

315 lb .

(142.9 k g)

0.7 in.

(18 mm)

INSTALLED

140 lb .

(63.5 kg)

197 lb .

(89.4 kg)

266 lb .

(120 .7 k g)

4 in.

(102 mm)

11.5 in.

(292 mm)

4 in.

(102 mm)

CAUTION

CAUTION

GENERAL INSTALLATION DATA

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.

The Toastmaster model griddles are equipped for use with the types of gas specified on the

nameplate.

All units are shipped from the factory for use with natural gas. The unit can easily be

converted for use on propane gas: See propane gas.

-IMPORTANT-

The installation of the Appliance should conform to the NATIONAL FUEL GAS
CODE "ANSI Z223.1 - LATEST EDITION" AND ALL LOCAL GAS COMPANY
RULES AND REGULATIONS.

IN CANADA INSTALLATION SHALL BE IN ACCORDANCE WITH THE
CURRENT CAN/CGA-B149.1 NATURAL GAS INSTALLATION CODE OR
CAN/CGA-B149.2 PROPANE INSTALLATION CODE AND LOCAL CODES
WHERE APPLICABLE.

Improper installation, adjustment, alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating and maintenance instructions
thoroughly before installing or servicing the equipment.

CAUTION

CAUTION

For your safety, do not store or use gasoline or other ammable vapors and liquids in

the vicinity of this or any other appliance. Keep the appliance area clear and free from
combustibles.

This appliance, its pressure regulator and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of that system at test
pressures in excess of 1/2 PSIG (3.45KPA).

This appliance and its pressure regulator must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure testing of the gas supply piping system

at test pressures equal to or less than 1/2 PSIG (3.45KPA). For your protection, we recommend a
qualified installing agency install this appliance. They should be familiar with gas installations and
your local gas requirements. In any case, your gas company should be called to approve the final

installation. In addition, there should be posted, in a prominent location, detailed instructions to be
followed in the event the operator smells gas. Obtain the instructions from the local gas supplier.

For your safety, if you smell gas -

1. Do not touch electrical switches.

2. Extinguish any open ame.

3. Immediately call your gas company.

KEEP THE APPLIANCE AREA FREE AND CLEAR FROM COMBUSTIBLES.

CLEARANCE

For use on non-combustible countertops only.

2M-Z12966: Toastmaster TMGT Series Gas Griddles

Combustible and non-combustible material must be at least 48" (120cm) from the top of the
appliance and 6" (150mm) from the sides and back. Adequate clearance should also be

provided for proper operation and servicing.

AIR SUPPLY

Make certain not to obstruct the ow of combustion and ventilation air. Provisions for adequate air

supply must be furnished. The legs supplied with the unit must be installed. Make certain that air
intake openings in the bottom of the appliance are not obstructed. They are essential for proper
combustion and operation of the appliance.

EXHAUST CANOPY

It is essential that facilities be provided over the griddle to carry off fumes and gases.

However, the unit should not be directly connected to a ue or stack.

LEVELING UNIT

This griddle is supplied with (4) feet which must be screwed into the legs attached to the
body. Level unit by adjusting the (4) feet which have an adjustment of 1-3/4" (43.75mm) for
accurate and perfect lineup with other units. After the griddle is in its final position, adjust
the legs to create 1/8 inch slant from back to front on the griddle plate. This will allow

grease to run into the grease gutter and provide the proper combustion air for the burners.

CAUTION

DO NOT INSTALL WITHOUT ATTACHING FEET - DO NOT REMOVE FEET.

GAS PIPING

Gas piping shall be of such size and so installed as to provide a supply of gas sufficient to meet

the full gas input of the appliance. If the appliance is to be connected to existing piping, it shall be
checked to determine if it has adequate capacity. Joint compound shall be used sparingly and only

on the male threads of the pipe joints. Such compounds shall be resistant to the action of LP gases.
WARNING: Any loose dirt or metal particles which are allowed to enter the gas lines on this appliance
will damage the valve and affect its operation. When installing this appliance, all pipe and fittings must

be free from loose dirt.

GAS PRESSURE REGULATOR

A convertible pressure regulator is provided with each griddle. It should be connected to the inlet pipe

at the rear of the unit. The gas supply line is then connected to it. It is shipped set for 6" (15.24cm)

water column manifold pressure for use with natural gas.

MANUAL SHUT-OFF VALVE

A manual shut-off valve should be installed upstream from the union and within 6 feet (1.829m) of this

appliance.

LP [PROPANE] GAS CONVERSION

This griddle is equipped with fixed orifice hoods and is shipped from the factory for use on natural

gas. Note: TMGM & TMGT units use a #47 drill orice for natural gas and a #55 drill orice

for propane. To convert to propane gas, install the burner orifice hoods, located in the grease

drawer, as follows:

1. Remove front panel by removing screws located on the front and the bottom.

2. Remove the burner(s) from the orifice hood(s). This is accomplished by removing the burner
mounting screw(s) and sliding the burner(s) off the hood(s).

3. Remove natural gas orifice hood(s) and install the propane hood(s) furnished.

4. Reinstall burner(s).

5. Reinstall front panel.

6. Remove the slotted, or hex-threaded, plug from the pressure regulator. Invert the plug and re­install. The letters "LP" should now be visible on the plug. The regulator is now set for 10" (25.4cm)

water column.

2M-Z12966: Toastmaster TMGT Series Gas Griddles

7. Set manifold pressure to 10" (25.4cm) water column. A 1/8" pipe plug on the supply pipe can be

removed for attaching a pressure gauge.

CONNECTING GAS SUPPLY LINE

The gas inlet of the griddle is sealed at the factory to prevent entry of dirt. Do not remove this seal
until the actual connection is made to the gas supply line.

CHECKING FOR GAS LEAKS

Soap and water solution or other material acceptable for the purpose shall be used in locating gas
leakage. Matches, candle ame, or other sources of ignition shall not be used for this purpose.
Check entire piping system for leaks.

LIGHTING INSTRUCTIONS

When griddle is first lit, it will smoke until the preservation oils and impurities are burned off.

1. Turn off main valve to unit and wait 5 minutes to clear gas.

2. Turn off all knobs and pilot valves.

3. Turn on main valve and light all pilots.

4. Turn burner knobs to desired setting.

5. To turn burners off, turn knobs off.

NOTE: The griddles are equipped with standing pilots and should be lit immediately after
the gas is turned on.

Pilot ames can be lit and observed through the front panel view ports. However, best access for
lighting the pilot is from the bottom of the unit just behind the center wall.

PILOT LIGHT REGULATION

Adjust pilot light ames as small as possible, but high enough to light burner immediately when

burner valve is turned on high.

BURNER ADJUSTMENT (MODELS TMGM)

1. Remove the front panel.

2. Turn burner valve knob to "HI" position.

3. Close the air shutter on the front of the burner to give a soft blue ame having luminous tips and
open to a point where the yellow tips disappear and a hard blue ame is obtained. Repeat for all

burners.

BURNER ADJUSTMENT (MODELS TMGT)

1. Remove the front panel.

2. Push dial in and set thermostat of one burner to 450°F (229.9°C).

3. Close the air shutter on the front of the burner to give a soft blue ame having luminous
tips and open to a point where the yellow tips disappear and a hard blue ame is obtained.

Repeat for all burners.

BURNER OPERATION (MODELS TMGM)

To ignite burners, turn burner valve knob to "HI" position. Each burner is controlled by an individual
high-low, on-off valve. An infinite number of temperatures may be obtained by turning the burner valve
knob to any position between high and low. For overnight shutdown, turn the valves to the "OFF"

position.

SEASONING THE GRIDDLE SURFACE (NON-CHROMIUM SURFACES)

Clean the griddle surface thoroughly. After the griddle has been thoroughly cleaned, it should be

seasoned to prevent food from sticking. Before using, and after each thorough scouring, season the
griddle heating surface in the following manner:

1. Turn the temperature control dial to 350°F (174.9°C).

2. Using a clean cloth, not a spatula, spread a thin film of cooking oil over the griddle cooking surface.
This film should remain on the hot griddle surface 1/2 hour.

3. Remove excess oil and wipe clean.

4. Apply another film of cooking oil over the hot cooking area for another 1/2 hour and again remove

excess oil and wipe clean. The griddle surface should now be ready for use.

2M-Z12966: Toastmaster TMGT Series Gas Griddles

Even with careful seasoning food may, to some extent, stick to the griddle cooking
surface until griddle plate is "broken in."

CAUTION

COOKING (MODELS TD)

Set the thermostat dial knob to the temperature desired. After a short preheating period, the
thermostat will automatically maintain the selected temperature.

GREASE PAN

A grease pan is located at the front and can be removed for cleaning from the front. This pan should
be checked and emptied on a regular basis.

EXERCISE EXTREME CARE IN HANDLING THE GREASE PAN CONTAINING HOT
GREASE.

GRIDDLE CARE (NON-CHROMIUM AREAS)

It takes very little time and effort to keep the griddle attractive and performing at top efficiency.

If grease is permitted to accumulate, it will form a gummy cake and then carbonize into a hard

substance which is extremely difficult to remove. To prevent this condition, the following suggestions
for cleanliness should be followed:

1. After each use, scrape the griddle with a scraper or exible spatula to remove excess grease and

food. A waste drawer is provided for the scrapings. If there is an accumulation of burned on grease
and food, the griddle should be thoroughly scoured and reseasoned. Use pumice or griddle stone
while the griddle is warm. Do not use steel wool because of the danger of steel slivers getting into
the food.

2. Daily-use a clean cloth and good non-abrasive cleaner to clean the stainless steel body of the

griddle. Wipe the polished front with a soft cloth.

3. At least once a day remove the waste drawer and wash in the same way as an ordinary cooking

utensil. The drawer is removed by pulling forward, up and out.

TEMPERATURE CONTROL

TMGT: The temperature controls are combination “ON/OFF” switches and thermostats. Turning the dial

knob automatically maintains the selected heat range. There is one thermostat for every twelve [12]
inch (305 mm) wide section that operate independently.

TMGM: To ignite burners, turn burner valve knob to highest temperature position. Each burner is controlled
by an individual high–low, on/off valve. Any temperature in the operable range may be obtained by turning

the burner valve knob to any position between high and low and adjusting for time and application. For
over- night shutdown, turn the valves to the “OFF” position.

COOKING

TMGT: Set the thermostat dial knob at the desired temperature. After a short pre-heating period, the

thermostat will automatically maintain the selected temperature.

TMGM: Adjust the knob to the desired area in the heat range. Once the desired heat is reached make
adjustments over time to maintain target heat.

IDLING: During idle periods, to save on operating costs, lower the temperature setting of the thermostat

to about 250°F (121°C) on thermostatic models and to a low heat setting on manual models. It is not

necessary to maintain cooking temperature during idle periods, as the griddle can quickly be reheated
to the desired temperature.

2M-Z12966: Toastmaster TMGT Series Gas Griddles

SIGNAL LIGHTS: On thermostatic models, each thermostat has its own signal light which indicates
when the unit’s control knob is not in the off position.

FRONT—PANEL AND CONTROLS
RIGHT SIDE—PANELS

TMGT36 shown

35

27

28

29

36

18

REAR PANEL
LEFT SIDE— PANELS

TMGT36 shown

4

33

30

2M-Z12966: Toastmaster TMGT Series Gas Griddles

23444 262626 1116

9

31

3032

BOTTOM

TMGT36 shown

228

31

31

4

4

21

17

THERMOSTAT [TMGT ONLY] AND BURNERS

TMGT36 shown

34

4

2M-Z12966: Toastmaster TMGT Series Gas Griddles

1

A

14

13

10

7

6

3

20 15 14

12

35

14

23

27

THERMOSTAT
[TMGT MODELS ONLY]

19

18

PARTS LIST

Side references are from the operator's point-of-view—from the front of the unit.
Items labeled “NS” are non-serviceable. Items labeled “NP” are not pictured.

REF NO MODE LQ TYPART NUMBERD ESCRIPTION

TMGM24 2

TMGM36 3

1

2A LL 2G3-Z6036 7

3

4

5A LL 12P-1453N P

6

7

8

9

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 4

TMGM48 4

TMGM24 2

TMGM36 3

TMGM48 4

TMGM24 46

TMGM48 58

TMGM24 2

TMGM36 3

TMGM48 4

TMGM24 2

TMGM36 3

TMGM48 4

TMGT24/TMGM24

TMGT36/TMGM36G 3-Z5929p anel, bottom 36-inch

TMGT48/TMGM48G 3-Z5939

TMGM24/TMGT24G 3-Z5953

TMGM36/TMGT36G 3-Z5955p anel, rear 36-inch

TMGM48/TMGT48G 3-Z5957p anel, rear 48-inch

2F-Z5949 7u-burner

G3-Z5946 7cover, gas

2C-88236 , 7

2V-66717 valve, pilot

2V-Z6647 7burner, pilot

G3-Z5919

2TMGT24

3TMGT36

4TMGT48

drawer slide

2TMGT24

3TMGT36

4TMGT48

59TMGM36

screw, #8 x 0.375-inch

46TMGT24

55TMGT36

58TMGT48

manifold plug

2TMGT24

3TMGT36

4TMGT48

2TMGT24

3TMGT36

4TMGT48

panel, bottom 24-inch

panel, bottom 48-inch

1

panel, rear 24-inch

PAGE NO

7

6

2M-Z12966: Toastmaster TMGT Series Gas Griddles

Some items are included for illustrative purposes only and in certain instances may not be available.

PARTS LIST

10 ALL1 G3-6243047

TMGM24/TMGT24

11

12

13 ALL1 G3-Y7046 7

14

15

16

17

2M-Z12966: Toastmaster TMGT Series Gas Griddles

18

19

TMGM36/TMGT36G 5-Z4813fl ue, 36-inch

TMGM48/TMGT48G 5-Z4814

TMGM24 2

TMGM36 3

TMGM48 4

TMGM24

TMGM36 G3-636306

TMGM48 G3-648306

TMGT24 G3-624307

TMGT36 G3-636307

TMGT48 G3-64830 7

TMGM24 2

TMGM48 4

TMGM36

TMGM48

TMGT36

TMGT48

TMGM24 2

TMGM36 3

TMGM48 4

TMGT24 2

TMGT24 2

G3-624306

G3-GD0036N P

grease chute

G5-Z4812

1

2C-2555 NPnut, #8-32 acorn

2TMGT24

3TMGT36

4TMGT48

manifold, 24-inch without thermostat [ manual control]

manifold, 36-inch without thermostat [manual control ]

manifold, 48-inch without thermostat [manual control ]

1

manifold, 24-inch with thermosta t

manifold, 36-inch with thermostat

manifold, 48-inch with thermostat

3TMGM36

2A-9369

2TMGT24

3TMGT36

4TMGT48

1G5-Z4817 6flue divider

2TMGT24

3TMGT36

4TMGT48

2T-Z4293 6thermostat3TMGT36

4TMGT48

2K-Y7111 7assembled fitting, 90°3TMGT36

4TMGT48

flue, 24-inch

flue, 48-inch

grease drawer

probe tube assembl y

6

7

7fitting, orifice

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 2
INCLUDE MODEL AND SERIAL NUMBER OF 4

Some items are included for illustrative purposes only and in certain instances may not be available.

PARTS LIST

TMGM24 2

TMGM36 3

20

21

22

23 ALL1 2J-Z0792 6, 7

24

25

26

27

28

TMGM48 4

TMGT24 2

TMGT24 6

TMGT24 2

TMGM24

TMGM36

TMGM48

TMGT24 G4-Z12942-10

TMGT36 G4-Z12942-11

TMGT48

TMGM24 6

TMGM36 8

TMGM48 8

TMGM24 2

TMGM36 3

TMGM48 4

TMGT24

TMGM24 2

TMGM36 3

TMGM48 4

TMGT24

2K-Z4921 7

G3-Z4398 NPbulb cap3TMGT36

2C-6517N Pnut, 1/4-209TMGT36

G3-Y9531 NPinsulator3TMGT36

G4-Z12942-07

G4-Z12942-08

G4-Z12942-09

G4-Z12942-12

2C-Z2893 6nut, #10-24

2R-Z13014

2R-Z130153TMGT36 knob, with thermostat

2M-Z21075

2M-Z210743TMGT36 knob label, with thermosta t

2TMGT24

corrugated burner tube

3TMGT36

4TMGT48

4TMGT48

12TMGT48

pressure regulator

4TMGT48

1

6TMGT24

8TMGT36

8TMGT48

knob, without thermostat [manual control]

2

4TMGT48

knob label, without thermostat [ manual control]

2

4TMGT48

NPnameplat e

6

2M-Z12966: Toastmaster TMGT Series Gas Griddles

6

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 3
INCLUDE MODEL AND SERIAL NUMBER OF 4

Some items are included for illustrative purposes only and in certain instances may not be available.

PARTS LIST

29 ALL1 2M-Z209706

30 ALL

31 ALL4 2A-Z5942 leg 6, 7

32 ALL2 G3-6243026

33 ALL

TMGM24/TMGT24

34

35

36

37 ALL2 2C-Z6035

38

39

TMGM36/TMGT36G 3-Z5925c enter wall, 36-inch

TMGM48/TMGT48

TMGM24

TMGM36 G4-TC0102

TMGM48 G4-TC0105

TMGT24 G4-TC0097

TMGT36 G4-TC0103

TMGT48 G4-TC0106

TMGM24

TMGM36 G3-Z15807

TMGM48 G3-Z15809

TMGT24 G3-Z15806

TMGT36

TMGT48

TMGT24 2

TMGM24

TMGM36

TMGM48

G3-Z5915

G4-TC0096

G3-Z15799

G3-Z15808

G3-Z15810

2T-Y7590 NPstem, thermostat3TMGT36

2V-Y8832

2G3-Z5945 6side panel

1G3-6243036

1

top weldment, 24-inch without thermostat [manual control]

top weldment, 36-inch without thermostat [manual control]

top weldment, 48-inch without thermostat [manual control]

1

top weldment, 24-inch with thermostat

top weldment, 36-inch with thermostat

top weldment, 48-inch with thermostat

panel, front 24-inch without thermostat [manual control]

panel, front 36-inch without thermostat [manual control ]

panel, front 48-inch without thermostat [manual control]

1

4TMGT48

2

3

4

badge, Toastmaster

liner assembly, left

liner assembly, right

center wall, 24-inch

center wall, 48-inch

panel, front 24-inch with thermostat

panel, front 36-inch with thermostat

panel, front 48-inch with thermostat

bolt, 1/2-13 x 3-inch

manual gas control valve

6, 7

NP

NP

7

6

2M-Z12966: Toastmaster TMGT Series Gas Griddles

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 4
INCLUDE MODEL AND SERIAL NUMBER OF 4

Some items are included for illustrative purposes only and in certain instances may not be available.

LIMITED EQUIPMENT WARRANTY

Star Manufacturing [as well as its subsidiaries,
Toastmaster and Holman] warranties new products to
be free from defects in material and/or workmanship
for a period of one [1] year from the date of original
installation, except as noted below. Defects that
occur as a result of normal use, within the time period
and limitations defined in this warranty, will at Star’s
discretion have the parts replaced or repaired by Star or
a Star-authorized service agency.

THIS WARRANTY IS SUBJECT TO ALL LISTED CONDITIONS.

Repairs performed under this warranty are to be
performed by a Star authorized service agency. Star
will not be responsible for charges incurred or service
performed by non-authorized repair agencies. In all
cases, the nearest Star-authorized service agency must
be used. Star will be responsible for normal labor charges
incurred in the repair or replacement of a warrantied
product within 50 miles (80.5 km) of an authorized
service agency. Time and expense charges for anything
beyond that distance will be the responsibility of the
owner. All labor will need to be performed during regular
service hours. Any overtime premium will be charged
to the owner. For all shipments outside the U.S.A. and
Canada, please see the International Warranty for specific
details. It is the responsibility of the owner to inspect and
report any shipping damage claims, hidden or otherwise,
promptly following delivery. No mileage or travel charges
will be honored on any equipment that is deemed
portable. In general, equipment with a cord and plug
weighing less than 50 lb. (22.7 kg) is considered portable
and should be taken or shipped to the closest authorized
service agency, transportation prepaid.

PORTABLE EQUIPMENT EXAMPLES

• 514LL fryer

• 15MC and 18MCP hot food
merchandisers

• QCS1, QCS2, and RCS2 toasters

• 16PD-A pretzel merchandisers

• Condiment dispensers
except HPD- and SPD-series
models

• All pop-up toasters

• All pastry display cabinets

• All heat lamps

CONTACT

Should you require any assistance regarding the
operation or maintenance of any Star equipment;
write, phone, fax or email our service department. In
all correspondence mention the model number and
serial number of your unit, as well as the voltage or
type of gas you are using.
Business hours are 8:00 a.m. to 4:30 p.m. Central
Standard Time (CST)
Telephone: [phone]
Fax: [phone]
Email: [e-mail]
www.star-mfg.com

• J4R popcorn machine

• 12NCPW and 15NCPW nacho
merchandisers

• Nacho cheese warmers
except 11WLA-series models

• Specialty food warmers
except 130R, 11RW, and 11WSA
models

• All butter dispensers

• All nacho chip merchandisers

• All accessories

WARRANTY EXCLUSIONS

THE FOLLOWING WILL NOT BE COVERED UNDER WARRANTY.

• Any product which has not been used, cleaned,
maintained, or installed in accordance with the directions
published in the appropriate installation sheet and/
or owner’s manual as well as national and local codes,
including incorrect gas, electrical, or water connection. Star
is not liable for any unit which has
been mishandled, abused, misapplied, subjected to
chlorides, harsh chemicals, or caustic cleaners, damaged
from exposure to hard water, modified by unauthorized
personnel, damaged by flood, fire, or other acts of nature
[or God], or which have an altered or missing serial number.

• Installation, labor, and job checkouts, calibration of heat
controls, air and gas burner/bypass/pilot adjustments, gas
or electrical system checks, voltage and phase conversions,
cleaning of equipment, or seasoning of griddle surface.

• Replacement of fuses or resetting of circuit breakers,
safety controls, or reset buttons.

• Replacement of broken or damaged glass components,
quartz heating elements, and light bulbs.

• Labor charges for all removable parts in gas charbroilers
and hotplates, including but not limited to burners, grates,
and radiants.

• Any labor charges incurred by delays, waiting time, or
operating restrictions that hinder a service technician’s
ability to perform service.

• Replacement of items subject to normal wear or items
that can easily be replaced during a daily cleaning routine,
such as but not limited to knobs, bulbs, fuses, quartz
heating elements, baskets, racks, and grease drawers.

• Components that should be replaced when damaged
or worn, but have been field-repaired instead [eg. field­welded fry pots]

• Any loss of business or profits.

PRODUCTS PARTS LABOR

Star-Ultra Max® fryers, griddles,

2 years 2 years

charbroilers, and hotplates

Star-Max® fryers, griddles, char­broilers, and hotplates

Jetstar® popcorn poppers

Staltek™ roller grill coatings

Cast iron grates, burners; and
burner shields

Star, Toastmaster, or Holman
parts sold to repair equipment

2 years 2 years

2 years 2 years

5 years

180 days

90 days

Service First 1 year

2M-Z12966: Toastmaster TMGT Series Gas Griddles

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

2M-Z21647 ∙ Rev. E ∙ 01.2019

TOASTMASTER • www.star-mfg.com
265 Hobson St. • Smithville, TN 37166
Telephone: [phone] • Fax: [phone]

Printed in the U.S.A. • 2M-Z12966 • Rev E • 06.2019
Specifications are subjec t to change without notice .