Toa TZ-S240W-AS Instruction Manual

SLIM ARRAY SPEAKER

INSTRUCTION MANUAL

TZ-S240W-AS

Thank you for purchasing TOA’s Slim Array Speaker.
Please carefully follow the instruction in this manual to ensure long, trouble free use of your equipment.

TABLE OF CONTENTS

1. SAFETY PRECAUTION .............................

2. GENERAL DESCRIPTION ..........................

3. FEATURES .................................................

4. A BO UT TH E I NP UT OV ER LO AD

PROTECTION CIRCUITRY ...................

5. COVERAGE AREA ..................................

6. DIMENSONAL DIAGRAM .........................

2
3
3

3
4
4

7. INTERNAL WIRING DIAGRAM ..............

8. CHANGING TO HIGH IMPEDANCE .......

9. JO INING SPEAKERS .. .................... ....

10.DIRECT WALL MOUNTING ................

11.S PECI FIC ATIONS .... ..... ..... .... ... .... .

5
5
6
7
8

11. SPECIFICATIONS

Note: The design and specification is subject to change without notice for improvement.

Accessories:

Mounting Bracket .......... 2 pcs

533-06-263-0A

Model No.
Enclosure

Power Handling Capacity
Impedance
Sensitivity (1 W, 1 m)
Frequency Response
(Deviation -10 dB)

Crossover Frequency

Directivity Angle

Speaker Component

Input Terminal
Operating Temperature
Finish

Dimensions
Weight

TZ-S240W-AS

Bass reflex type

Continous: 240 W, Program: 480 W

8 W

94 dB

95 - 20,000 Hz

2.5 kHz

o

Horizontal: 100

o

Vertical: 5

Low frequency: 10cm (4”) cone type x 8
High frequency: 2.5cm (1”) balanced dome type x 24

o o

-10 ~ +50 C

Enclosure: MDF, White Paint

160 (w) x 950 (h) x 262 (d) mm

17 kg

M4 screw terminal x 2

Front Grille: Punched Steel Plate, White Paint

Optional products

Matching transformer: MT-S0601
Extension plate: SR-EP4
Flying bracket: SR-FB4
Wall tilt bracket: SR-TB4

Wall mounting bracket: SR-WB4
Floor stand: SR-FS4
Stand adapter: SR-SA4

Traceability Information for Europe

Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamichi, Chuo-ku, Kobe,
Hyogo, Japan

Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany

URL: http://www.toa.com.sg/

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

1. SAFETY PRECAUTION

•

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.

• After reading, keep this manual handy for future reference.

Before installation and use, be sure to carefully read all the instruction in this section for correct and safe
operation.

Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury.

When Installing the Unit

• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface. Doing
so may result in the unit falling down and causing personal injury and/or property damage.

• Refer all installation work to the dealer from whom the speaker was purchased. Installation requires extensive
technical knowledge and experience. The speaker may fall off if incorrectly installed, resulting in possible
personal injury.

• Flying Precautions
Be sure to follow the instructions below. Otherwise, the suspension wires or belts may be off or snap and the
speaker may fall off, causing personal injury.

vCheck to confirm that the suspension wires and belts are strong enough to withstand the speaker load.
vThe connectors of the suspension wires and belts must be securely linked with those of the speaker.
vAll parts and components (such as enclosures, metal pieces, and screws) must be free from any

deformation, crack, and corrosion.

vBe sure to use screws supplied with the optional flying hardware when installing the speaker using such

hardware.

• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.

• Owing to the unit's size and weight, be sure that at least two persons are available to install the unit. Failure to do
so could result in personal injury.

• Do not use other methods than specified to install the speaker. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injury.

• Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so may
cause the speaker to fall, resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.

• Use the specified mounting bracket in combination. Doing otherwise may cause the unit or component to fall
off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the unit to fall, which could result in personal injury.

Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.

When Installing the Unit

• Avoid placing the unit in a doorway or other high traffic area as people may trip on the equipment and cords,
or be injured by falling objects.

• Avoid touching the unit's sharp metal edge to prevent injury.

• When installing the speaker at head height, attach Protection Pad to the bottom of the speaker. Failure to do
so may cause injury if people hit their heads directly against the speaker.

When the Unit is in Use

• Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate and result in a fire.

• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.

• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the unit or its mounting bracket that could cause the unit to fall, possibly causing
personal injury

2

7

10. DIRECT WALL MOUNTING

Use provided accesories bracket for direct wall mounting.

WARNING

CAUTION

Note: Bolt and screw for wall is not provided. Please use bolt and screw which suitable with wall structure and able

to handle weight of units.

(Included in product)

BH Screw M5

Bolt M8

Wall Fixing Screw M8

Wall moun t bracket

Pas s the wire through the hole

6 x 15°

230 mm

50

104

50

104

990

Hole distance for wall mount bracket

Unit: mm (millimeter)