Touch Accessible Platform for Interactive Technology
Model: TAP-IT S06-M XX
TAP-it
General Contact: 800.398.5652
www.teachsmart.org
Help Desk Contact:
US Toll Free 800.398.5652 Ext.623
tapit@stampedeglobal.com
TMC
Contents
Contents. ......................................................................................................................................................................... 2
Weight Limit. .................................................................................................................................................................... 2
Warning Statements. ....................................................................................................................................................... 2
Installation Tools. ............................................................................................................................................................. 3
Whats In the Box. ............................................................................................................................................................ 3
Features. ......................................................................................................................................................................... 4
Monitor Input Connectivity. .............................................................................................................................................. 5
Choosing a Viewing Location. ......................................................................................................................................... 6
Unpacking and Assembling the Mobile Flat Panel Cart................................................................................................... 6
Introduction. .............................................................................................................................................................. 6
Removing TAP-it From Packaging. .......................................................................................................................... 6
Inspecting Cart. ......................................................................................................................................................... 6
Caster Operation. ............................................................................................................................................................ 7
Computer Shelf Install. .................................................................................................................................................... 7
Technical Specications. ................................................................................................................................................. 8
Operation. ........................................................................................................................................................................ 9
Troubleshooting. ............................................................................................................................................................ 10
TMC-3 Cart Checklist. ....................................................................................................................................................11
Warranty. ....................................................................................................................................................................... 12
Weight Limit
THE FLOOR STRUCTURE MUST BE CAPABLE OF
SUPPORTING AT LEAST FIVE TIMES THE WEIGHT
Max Weight Capacity: 225lbs
OF THE CART AND FLAT-PANEL. IF NOT, THE FLOOR
STRUCTURE MUST BE REINFORCED.
Warning Statements
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED
IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE
PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
SmartEd SERVICES DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY SmartEd SERVICES
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR
IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
At least two qualied people should perform the assembly procedure. Personal injury and/or property damage can result
from dropping or mishandling the at panel.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious personal
injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of
impact.
This product shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, cups or
containers, shall be placed on the product.
This product shall be connected to a MAINS socket outlet with a protective earthing connection.
This product shall properly be connected to either a laptop or personal computer source utilizing the VGA, 3.5 mm audio,
and USB cabling supplied and installed to operate as a multimedia system.
Where the MAINS plug or an appliance coupler is used as the disconnect, the disconnect device shall remain readily
operable.
The maximum weight capacity for the computer shelf is 100 lb.
Page 2 Installation Instructions
TMC
Installation Tools
The following tools may be required, dependent upon your particular installation. These tools are not provided
with the TAP-it, but you can purchase them at your local hardware store.
Phillips Tip Screwdriver
Whats In the Box
Your TAP-it product is shipped with all proper installation hardware and components. Make sure that none of these
parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please
stop the installation and contact US toll free @ (800) 398-5652 Ext.623
Mobile Flat Panel Cart Hardware
TAP-it ®
(Qty 1)
Removable Laptop Shelf
(Qty 1)
Clamp
(Qty 2)
Setup Manual and CD-Rom
(Qty 1) each
Laptop Shelf Strap
(Qty 1)
Screw For Clamp
(Qty 2)
Wireless Remore Control (Qty 1)
and AAA batteries (Qty 2)
Display Switch Cover
(Qty 1)
Screw For Main Switch
(Qty 2)
Installation Instructions Page 3
Features
TMC
Electronic Tilt Housing
Allows you to tilt the at-panel
from 0° to 90° at the touch
of a button
Lifting Column Height
Adjustment & Display
Angle Control Pad
Raises/lowers stand
and tilts display with a
simple touch of a button
Interactive Display
Enables end-user control of the
computer or programs via touch of
the screen
Solid Base
Durable steel construction
Lifting Column Housing
Houses all internal
lifting components
Page 4 Installation Instructions
Locking Caster Wheels
Locking casters sercure
unit in place while in use
TMC
NE
C Display Solutions of America, Inc.
LCD4215 Installation Guide
42” LCD Display
Rev 1.1
Monitor Input Connectivity
Type A Terminal
Type B Terminal
TType C ype C TTerminalerminal
Installation Instructions Page 5
TMC
Choosing a Viewing Location
Unpacking and Assembling the Mobile Flat-Panel Cart
Introduction
Congratulations on the purchase of your mobile adjustable at-panel cart.
Your mobile at-panel cart has been designed and built with ease of operation and assembly in mind.
Please read these guidline instructions once thoroughly before attempting to unpack and assemble your cart.
Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and
tools you need to safely complete the assembly.
In addition, some steps of these instructions may require two people to prevent personal injury and/or damage to your
mobile at-panel cart/at-panel. Please observe all warnings in the following installation procedure and utilize proper
safety equipment at all times.
Removing TAP-it From Packaging
• Remove the individually sealed up box located
behind the cart unit. This box contains the laptop shelf.
• Remove the vertical cardboard support braces that
stand on both sides of the display.
• The cart is now ready to be removed from the bottom
cardboard cradle. With at least one person located on
each side of the unit, lift up from the base tubing
to remove the unit from the cradle.
• Once the unit has been placed onto the oor, carefully
remove the plastic bag and display cover.
• It is recommended that all of the packaging materials be
kept and stored.
Inspecting Cart
• Inspect the mobile at-panel cart for any damage that
may have occured during shipping.
Page 6 Installation Instructions
TMC
Caster Operation
The casters can be locked so that the wheels cannot
spin and the caster cannot rotate
To Lock the Caster
• Press down on the bottom tab labeled “ON”on the
locking caster.
To Unlock the Caster
• Press down on the top tab labeled “OFF”on the
locking caster.
Lock release Tab
Locking Tab
Computer Shelf Install
• Remove shelf from packaging.
• Remove the tie holding the 15-pin VGA, 3.5 mm audio, and
USB control cabling bundle located at the cable access
hole on the rear of the head assembly.
• Completely remove the rubber grommet from the cable
access hole where the laptop shelf will be installed.
• Feed the cabling ends through the matching cable access
hole on the laptop shelf, and install the shelf to the rear of
the head assembly via the (3) thumb screws located on the
shelf.
• Tighten the Phillips head of the thumb screws utilizing a
screwdriver as needed.
• Feed the cable ends through the rubber grommet and
re-install it into the cable access hole accordingly.
Installation Instructions Page 7
Technical Specications
All measurements are in inches [mm].
TMC
Page 8 Installation Instructions
TMC
Operation
Lower Display Angle Raise Display Angle
Control Pad
Lower Display Height Raise Display Height
CAUTION
Clear Any Obstructions
Before Lowering
Installation Instructions Page 9
TMC
Troubleshooting
The TAPit cart is a plug and play solution, and has already been congured and tested for immediate use. Should you
experience any immediate technical issues upon plugging the unit into a power source, please proceed with the following
steps prior to contacting customer service:
1. What should I do if the lift or extension systems won’t work?
a. Conrm if the power cable of the unit is properly plugged into the appropriate power supply.
2. What should I do if the lift or extension systems operate intermittently?
a. First retract the display so that it’s in the vertical home position, and then lower the lift until it comes
to a complete stop.
b. Release the down button on the controller.
c. Depress the down button again and hold it for a minimum of 10 seconds or until the unit both
visibly and audibly initializes. (The unit will noticeably move down as it is resetting itself to default.)
3. What should I do if the lift system will only move down?
a. First retract the display so that it’s in the vertical home position, and then lower the display until it
comes to a complete stop.
b. Release the down button on the controller.
c. Depress the down button again and hold it for a minimum of 10 seconds or until the unit both
visibly and audibly initializes. The unit will noticeably move down as it is resetting itself to default.
d. If the system is allowed to move upwards, then this is conrmation that the initialization was successful.
4. What should I do if I cannot see an image on the monitor?
a. Conrm if the display power cable is properly plugged into the appropriate power supply.
b. Power down the laptop or PC tower fully.
c. Conrm that all of the cabling is properly connected to the laptop or PC tower terminals.
d. Conrm that the main power switch located on right side bottom edge of the display is turned on
and that the LED light is illuminated.
e. Utilizing the supplied NEC remote control, conrm that the computer input is the selected input source.
f. Power on the laptop or computer source.
g. For laptops, conrm that the Function and appropriate F# key has been pressed to send the local
monitor signal to the monitor and to extend the desktop.
5. What should I do if I cannot hear any audio from the monitor speakers?
a. Conrm that the 3.5 mm audio cable is properly plugged into the laptop or PC tower.
b. Conrm that the laptop or PC tower volume level is turned up and/or not muted.
c. Utilizing the supplied NEC remote control conrm that the monitor audio level is turned up and/or not muted.
6. What should I do if the interactive touch capability of the monitor is not working?
a. Conrm that the USB control cable is properly plugged into the laptop or PC tower.
b. Conrm that the interactive software is properly loaded onto the laptop or PC tower.
Page 10 Installation Instructions
Home Position
TMC
TMC-3 Cart Checklist
Part Number: TMC-3-XX-82
ITEM DETAILED DESCRIPTION PASS COMMENTS
Quality Control Checklist
1 Cosmetic
2 Lift Columns
3 Tilt Actuator
4 Video
5 Audio/Speakers
6 Cable Passage
7 Secured Screws Check that all screws are tight and fastened properly.
8 Casters
Hipot and Ground
Test
10 Inspection Sticker
Visually inspect assembly paint for discrepancies i.e., scratches,
blemishes, dings, etc.
Physically test the unit by moving it up and down using the remote
control a minimum 5 times.
Physically test the unit by tilting it up and down using the remote
control a minimum 5 times.
Connect the unit to a laptop and verify on/off control via the remote,
and that the laptop image displays.
audio from the laptop source can be heard.
Check that all cables passageways are clear and that all cables do
not bind/kink up, and are secured in place.
Check that all (4) casters are tight and functional, including the
locking mechanism.
Connect the TAP-it cart power cord to the Hipot tester, and connect
the ground cable to a bare metal contact point. Press test button 9
Check the sticker for operators initials on all testing conducted and
deemed acceptable.
Check that each of the following items are included:
□ NEC Naviset document
□
NEC LCD4215/V423 set-up manual
□ NEC LCD software and documentation CD-ROM
□
11 Accessories Bag
NEC SP-4046 speaker quick start guide
□ NEC remote control
□ NEC main power cover and screws
□ Set of AA batteries
□ PC velcro strap
□ TAP-it user manual
12 Product Packaging Check that the unit is properly packed and protected for shipment.
Inspector: Date:
Tap-It Serial #: NEC Display Serial #:
Installation Instructions Page 11
9541-000-000-0X REV.1
LIMITED WARRANTY
This Limited Warranty is specific to the TMC TAP-it Mobile Cart (the “Mobile Cart”) designed and
manufactured for Stampede Presentation Products, a Delaware Corporation. This Limited Warranty applies
only to the first user purchaser of the Mobile Cart, and not to any subsequent user and/or purchaser. This
Limited Warranty applies only to the Mobile Cart, and not to any other product or service.
1. WHAT IS COVERED BY THIS WARRANTY? This Limited Warranty covers defects in materials or
workmanship relating to the components of the Mobile Cart for a period of three (3) years from the date of purchase
for the first user purchaser. Stampede Presentation Products will replace defective parts covered by this Limited
Warranty without charge during the applicable warranty period.
2. WHAT IS NOT COVERED BY THIS WARRANTY? This Limited Warranty does not cover (a) cleaning,
installation, setup, normal wear and adjustments; (b) incidental costs including, but not limited to, transporting
equipment to and from the place of purchase or the manufacturer; (c) damage caused by use of the Mobile Cart for
purposes other than those for which it was designed; (d) damage caused by accident or disasters such as fire, flood,
wind, or lightning; (e) damage resulting from unauthorized attachments, use of the equipment with unauthorized
attachments, or unauthorized modification; (f) damage resulting from improper installation of the Mobile Cart; or
(g) any other abuse or misuse of the Mobile Cart. There is no other express warranty relating to the Mobile Cart.
3. EXCLUSIVE WARRANTY. The foregoing Limited Warranty is exclusive and in lieu of all other warranties or
remedies, whether written, oral or implied. Any and all implied warranties of merchantability, fitness for a
particular purpose, course of dealing, or usage of trade are hereby expressly disclaimed and excluded.
4. LIMITATION OF REMEDIES. The Limited Warranty relating to the Mobile Cart is limited to the replacement
of defective parts. Under no circumstances, except to the extent otherwise permitted by applicable law, shall
Stampede Presentation Products be liable for any loss or damage, direct or indirect, special, incidental or
consequential arising out of the use or inability to use the Mobile Cart, including but not limited to any claim for
loss of profits, loss of savings or revenue, loss of use of the Mobile Cart or any associated equipment, facilities or
service, downtime, the claims or costs of third parties, and/or injury to real or personal property. Some states do not
allow limitations on the duration of implied warranties or the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This Limited Warranty gives you specific
legal rights, and you may also have other rights varying from state to state.
5. FUTURE CHANGES. Stampede Presentation Products reserves the right to change or modify the construction
and/or design of the Mobile Cart or any component part or parts thereof without incurring an obligation to make
such changes or modifications in present products.
6. HOW TO OBTAIN REPLACEMENT PARTS. Only Stampede Presentation Products is authorized to provide
replacement parts for the Mobile Cart. In order to obtain a replacement part, please request a Returned Materials
Authorization Number (“RMA Number”) by contacting us through our web portal at
http://stampedeglobal.com/rma/. Returned parts will be evaluated by Stampede Presentation Products to determine
existence and extent of defect prior to sending a replacement. The customer is responsible for shipping charges
relating to parts sent to Stampede Presentation Products for evaluation. Stampede Presentation Products will pay
shipping charges of replacement parts back to the customer.
Loading...