TMC LI7WM User Manual

LI7WM
Socket 370 810E Chipset
Custom LPX from Factor Motherboard
User's Manual
Version 1.0A
The brand names, product names and trade names in this manual are trademarks or registered trademarks of their respective holders.
This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form, without prior consent in writing from the manufacturer.
The information in this document has been carefully checked and is believed to be accurate. However, the manufacturer assumes no responsibility for any inaccuracies that may appear in this manual. In no event will the manufacturer be liable for direct, indirect, special, exemplary, incidental or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The material contained herein is for informational purposes only.
Contents
Contents
Chapter 1 Introduction...................................................5
Chapter 2 Specifications .................................................6
Chapter 3 Hardware Description................................10
3.1 Processor..........................................................................................11
3.2 L2 Cache ..........................................................................................11
3.3 LMA Channels................................................................................11
3.4 BIOS ...................................................................................................9
3.5 I/O Port Address Map......................................................................9
3.6 Onboard PCI-IDE ...........................................................................9
3.7 Main Memory ...............................................................................10
3.8 Onboard Multi-I/O.............................................................................10
3.9 Interrupt Request (IRQ) Lines ...................................................11
3.10 Onboard VGA ...............................................................................11
3.11 TV-Out .........................................................................................11
3.12 Panel Link Sopport ....................................................................12
3.13 Onboard Ethernet Controller ....................................................12
Chapter 4 Configuring the Motherboard ...................14
4.1 CPU Frequency Selection .............................................................15
4.2 Clear CMOS Select: JP11 .............................................................15
4.3 Onboard Audio Enable/Disable :JP2 ..........................................16
4.4 Onboard LAN Enable/Disable :JP3 ............................................16
Chapter 5 Installation...................................................18
5.1 I/O Connectors................................................................................20
5.2 J1: S-VHS Connector.....................................................................20
5.3 J2: RCA Connector........................................................................20
5.4 J3: Panel Link Connector (option)...............................................21
5.5 J4: CRT Connector.........................................................................21
5.6 J5: USB Connector.........................................................................22
5.7 J6/J7: PS/2 Keyboard and PS/2 Mouse Connectors ...............22
5.8 J8/J9: Serial Ports .........................................................................23
5.9 J10: Parallel Port Connector .......................................................23
5.10 J11: RJ45 Connector ..................................................................24
5.11 J J12, J13, J14: Line Out, Line In, Mic Connectors .............24
5.12 J15: IrDA Connector BL21PI Riser Card ..............................24
5.13 J16: OWL (Wake On Lan) Connector ....................................24
5.14 J17: Game Port Connector ........................................................25
5.15 J18: CPU Fan Power Connector ..............................................25
Contents
5.16 J19 Front Bezel Connectors........................................................25
5.17 J20: ATX Power Supply Connector .......................................26
5.18 J21: Floppy Drive Connector ...................................................26
5.19 J22,J23: IDE1 and IDE2 Connector ........................................27
5.20 J24,J25: CD-ROM Audio In Connector...................................28
5.21 J26: Chassis Fan Power Connectors .......................................28
5.22 J27: CPU Fan Power Connectors ............................................28
5.23 J28: Reset Switch .........................................................................28
5.24 JP1:TV-Out: PAL/NTSC............................................................29
5.25 JP2: Onboard Audio In Connector............................................29
5.26 JP3: Onboard Lan Enable/Disable ............................................29
5.27 JP4: Boot Block/Unlock..............................................................30
5.28 JP5: Clear CMOS Slect ...............................................................30
5.29 S1: BL21PI Riser Card Connector............................................30
Chapter 6 BIOS and System Setup.............................32
6.1 BIOS Introduction..........................................................................35
6.2 BIOS Setup......................................................................................35
6.3 Standard CMOS Setup...................................................................37
6.4 BIOS Features Setup......................................................................40
6.5 Advanced Chipset Features Setup .............................................43
6.6 Intergrated Prephierals ................................................................45
6.7 Power Management Setup ..........................................................48
6.8 PNP/PCI Configuration ...............................................................51
6.9 PC Health Status ...........................................................................52
6.10 Frequency/ Voltage Control .....................................................52
6.11 I Load Fail-Safe Defaults ..........................................................54
6.12 Load Optimized Defaults ..........................................................54
6.13 I Set Supervisor / User Password ............................................55
6.14 Save & Exit Setup ........................................................................56
6.15 Exit Without Saving.....................................................................56
Chapter 7 Audio Driver Installation Guide ................58
Chapter 8 VGA Driver Installation Guide .................62
Chapter 9 LAN Driver Installation Guide ..................68
Chapter 10 System Monitor Utility User’s Guide .......86
Chapter 11 LI7WM and the Databook Case...............94
Chapter 1 Introduction
This manual is designed to give you information on the LI7WM motherboard. It is divided into the following sections:
Introduction
Specifications
Hardware Description
Configuring the Motherboard
Installation
BIOS and System Setup
Audio Driver Installation Guide
VGA Driver Installation Guide
LAN Driver Installation Guide
System Monitor Utility User’s Guide
Checklist
Please check that your package is complete and contains the items below. If you discover damaged or missing items, please contact your dealer.
The LI7WM Motherboard with the BL7WM Riser Card
1 40-pin IDE ribbon cable (14 cm)
1 40-pin CD-ROM ribbon cable (8 cm)
1 34-pin FDD ribbon cable (20 cm)
1 16-pin game port cable
Chapter 2 Specifications
Chapter 2 Specifications
CPU Socket
PGA370 Socket
Processor
Intel Celeron ( PGA370 ) and Pentium III ( FC-PGA370 ).
300MHz~1GHz
L2 Cache
CPU integrated L2 cache
Chipset
Intel 810E (GMCH in 421 BGA and ICH in 241 BGA)
Year 2000 Compliant BIOS
The onboard Award BIOS is Year 2000 Compliant and will pass software applications that have the tendency to invoke INT1AH function 04H such as year 2000.exe utility released by NSTL. The BIOS comes with ISA Plug and Play (PnP) extension, DMI, bootable CD-ROM and power -management features.
Power Connector
ATX power supply connector (Use an ATX power supply with 3.3V power.)
Onboard Audio
Onboard AC97 Codec with external connectors for Line out, Line in, Mic, and Game port.
Onboard VGA
The highly integrated graphics accelerator consists of dedicated multimedia engines executing in parallel to deliver high performance 3D, 2D and motion compensation video capabilities. The 3D and 2D engines are managed by a 3D/2D pipeline preprocessor allowing a sustained flow of graphics data to be rendered and displayed. It also features a 4MB display cache buffer. Onboard TV-out connectors support S-VHS and RCA specifications.
TV-Out
Chrontel’s CH7007 digital PC to TV encoder is a stand-alone integrated circuit which provides a PC 99 compliant solution for TV output. Suggested for application use with the Intel 810 chipset and Intel 810E chipset, it provides a universal digital input port to accept a pixel data stream from a compatible VGA controller (or equivalent) and converts this directly into NTSC or PAL TV format.
Expansion Slots on Riser Card BL7WM
Two PCI 32-bit slots
Panel Link Support
The Sil154 transmitter uses PanelLink® digital technology to support display ranging from VGA to SXGA resolutions (25-112MPps) in a single link interface. The Sil154 transmitter has a highly width 12-bit (1/2 pixel) or 24-bit 1 pixel /clock input for true color (16.7 million) support. In 24-bit mode, the data may be latch on the positive or negative edge of the clock. In 12-bit mode, multiple clocking options exist: with a signal clock, data will be clocked on the falling and the rising edge; with dual clocks data can be clocked on either the falling edge of the rising edge of both clocks.
Onboard Ethernet Controller
The onboard Intel 82559B Ethernet controller is compatible with both the traditional 10Mbps and advanced 100Mbps LAN facilities. An RJ45 connector and Wake on LAN are supported by LI7WM.
DMI BIOS Support
Desktop Management Interface (DMI) allows users to download system hardware -level information such as CPU type, CPU speed, internal/external frequencies and memory size.
PCI Bus Master IDE Controller (Ultra DMA/33)
Supports two connectors for up to four IDE devices in two channels such as ATAPI Tape Backup and CD-ROM drives, PIO Mode 3/4 and Bus Mastering Ultra DMA/33/66 Hard Disk Drives.
Super I/O
Winbond 83627 HF with 1x ECP, 1x IrDA, 2x UART, 1xfdc, 3x fan, speed monitoring and 7x voltage monitoring and 2x temperature monitoring.
Keyboard and Mouse Connectors
PS/2 type
Chapter 2 Specifications
USB Connector
2 ports onboar d
Win95/98 shut-off
Allows shut-off control from within Windows 95/98
Modem-ring-on
Supports PC powering on through an external modem.
Board Dimensions
11.91" x 11.80" (30.3cm x 30.0cm)
Figure 1: Layout of the LI7WM Motherboard
Chapter 3 Hardware Description
This chapter briefly describes each of the major features of the LI7WM motherboard. The layout of the board in Figure 1 shows the location of the key components. The topics covered in this chapter are as follows:
3.1 Processor..........................................................................................11
3.2 L2 Cache ..........................................................................................11
3.3 BIOS .................................................................................................11
3.4 Main Memory....................................................................................9
3.5 I/O Port Address Map......................................................................9
3.6 DMA Channels .................................................................................9
3.7 Onboard PCI-IDE...........................................................................10
3.8 Interrupt Request (IRQ) Lines ......................................................10
3.9 Onboard Multi-I/O.........................................................................11
3.10 Onboard VGA ...............................................................................11
3.11 Onboard Audio .............................................................................12
3.12 Onboard Ethernet Controller (option).......................................13
3.13 Hardware Monitoring IC.............................................................13
3.1 Processor
The LI7WM motherboard is designed to take a Intel 810E processor running from 300/ 333/ 366/ 400/ 433/ 466/ 500/ 533/ 566/ 600 to 633MHz at 66MHz CPU bus speed or 550/ 600/ 650/ 700/ 750/ 800/ 850/ 900/ 950MHz at 100MHz CPU bus speed or 600/ 666/ 733/ 800/ 866/ 933 at 133MHz CPU bus speed with its Socket 370 processor connector.
3.2 L2 Cache
The L2 cache is integrated in the Intel 810E processor. The private L2 cache bus is not connected to package pins; rather its signals are routed between the two cavities using standard package techniques.
3.3 DMA Channels
There are seven DMA channels available on the motherboard. Only DMA2 is used by the floppy controller. In the case that ECP mode on the parallel port is utilized, DMA1 or DMA3 will be used.
3.4 BIOS
The BIOS on the LI7WM motherboard provides the standard BIOS functions plus the following additional feature:
Power Management
The power management feature provides power savings by slowing down the CPU clock, turning off the monitor screen and stopping the HDD spindle motor. The BIOS fully conforms to ACPI (Advanced Configuration and Power Interface) specification.
3.5 Onboard Multi-I/O
Onboard AC97 Codec with external connectors for Line out, Line in, Mic, and Game port.
3.6 I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses, which also becomes the identity of the device. There is a total of 1K port address space available. The following table lists the I/O port addresses used on the motherboard.
Chapter 3 Hardware Description
Address Device Description
000h - 01Fh DMA Controller #1 020h - 03Fh Interrupt Controller #1 040h - 05Fh Timer 060h - 06Fh Keyboard Controller 070h - 07Fh Real Time Clock,, NMI 080h - 09Fh DMA Page Register 0A0h - 0BFh Interrupt Controller #2 0C0h - 0DFh DMA Controller #2 0F0h Clear Math Coprocessor Busy Signal 0F1h Reset Math Coprocessor 1F0h - 1F7h IDE Interface 2F8h - 2FFh Serial Port #2(COM2) 378h - 3FFh Parallel Port #1(LPT1) 3F0h - 3F7h Floppy Disk Controller 3F8h - 3FFh Serial Port #1(COM1)
3.7 Onboard PCI-IDE
The PCI-IDE contro ller is a part of the Intel 810E chipset. It supports PIO mode 3/4 and bus mastering Ultra DMA/33 and DMA/66. The peak transfer rate of PIO mode 3/4 can be as high as 17MB/sec. Using HDDs that support Ultra DMA/33, the peak transfer rate can reach 33 and 66MB/sec. There are two IDE connectors - primary IDE and secondary IDE. With two devices per connector, up to four IDE devices can be supported.
3.8 Main Memory
The LI7WM motherboard supports two 168-pin DIMM (Dual In-line Memory Module) sockets to form a memory configuration from 64MB to 512MB. DIMM modules can be 64M and 256MB in SDRAM. In populating the DIMM sockets, any socket can be populated first. Refer to the following table on how to do the memory configuration.
(DIMM1) (DIMM2) Total Memory
64MB ----- 64MB
128MB ----- 128MB
64MB 64MB 128MB 128MB 64MB 192MB 128MB 128MB 256MB 256MB 64MB 320MB 256MB 128MB 384MB 256MB 256MB 512MB
3.9 Interrupt Request (IRQ) Lines
There are a total of 15 IRQ lines available on the motherboard. Peripheral devices use an interrupt request to notify the CPU for the service required. The following table shows the IRQ lines used by the devices on the motherboard:
Level Function
IRQ0 System Timer Output IRQ1 Keyboard IRQ2 Interrupt Cascade IRQ8 Real Time Clock IRQ9 Software Redirected to Int 0Ah or PCI Slot Int# IRQ10 Reserved or PCI Slot Int# IRQ11 Reserved or PCI Slot Int# IRQ12 PS/2 Mouse or PCI Slot Int# IRQ13 Co-Processor IRQ14 Primary IDE
IRQ15 Secondary IDE IRQ3 Serial Port #2 IRQ4 Serial Port #1 IRQ5 Parallel Port #2 or PCI Slot Int# IRQ6 Floppy Disk Controller IRQ7 Parallel Port #1
3.10 Onboard VGA
The Intel 810E chipset is the result of new design approach to optimize the shared memory architecture while maintaining the cost benefits of integration through Direct AGP and Dynamic Video Memory Technology.
a. Direct AGP
Direct AGP delivers AGP class graphics performance to PCs at reduced cost. Rather than simply combining two semiconductor cell libraries for component reduction, Intel architects combined the 2D and 3D video capabilities with the memory control unit. This functional overlap within the Graphics and Memory Controller (Intel® 82810E) enables Direct AGP. Direct AGP provides an integrated graphics part with the capability to make direct memory set-up calls (similar to those associated with standard AGP protocol) to system memory. Direct AGP calls can dynamically allocate and de-allocate system memory for complex 3D textures, preserving the benefits of standard AGP add-in solutions.
Chapter 3 Hardware Description
b. Dynamic Video Memory Technology
Dynamic Video Memory Technology (DVMT) enables breakthrough graphics and memory performance for all PC segments through Direct AGP and highly efficient memory use. DVMT ensures the most efficient use of all available memory – regardless of whether a frame buffer is present or the size of the main memory– for maximum 3D graphics performance. DVMT also responds to application requirements by automatically allocating the proper amount of display and texturing memory. For example, a 3D application might require more texture memory to enhance the richness of 3D objects. The operating system (OS) views the Intel 810 and 810E chipset driver as an application which uses Direct AGP to request re-allocation of additional memory for 3D applications and returns memory when not required. DVMT is highly scalable — as additional memory is added to the system, more memory will be available to enhance 3D applications. DVMT works dynamically and modulates the bandwidth available to the CPU, graphics and I/O interface, through the intelligent arbitration built into the Intel 82810E. This hard-coded logic evaluates the operating environment and prioritizes traffic to maximize bandwidth for memory intense multimedia applications.
c. Memory Usage with DVMT
The operating system requires allocation of up to 1Mbyte of system memory to support legacy VGA. System properties will display up to 1Mbyte less than physical system memory available to the operating system. The graphics driver for the Intel 810E/810 chipsets configurations will request up to 4Mbyte of memory from the OS to implement a maximum 1024 x768 screen resolution, 2Mbyte for a command buffer and 4Mbyte used for z-buffering. For high-end 3D applications, the drivers request allocation of system memory from the OS for graphics textures. When the 3D application is closed, the O/S will re-allocate system memory back for generic use.
3.11 TV-Out
Chrontel’s CH7007 digital PC to TV encoder is a stand-alone integrated circuit which provides a PC 99 compliant solution for TV output. Suggested application use with the Intel 810 chipset and Intel 810E chipset. It provides a universal digital input port to accept a pixel data stream from a compatible VGA controller (or equivalent) and converts this directly into NTSC or PAL TV format.
3.12 Panel Link Support
The Sil154 transmitter uses PanelLink® digital technology to support display ranging from VGA to SXGA resolutions (25-112MPps) in a single link interface. The Sil154 transmitter has a highly with 12-bit (1/2 pixel) or 24-bit 1 pixel /clock input for true color (16.7 million) support. In 24-bit mode, the data may be latch on the positive or negative edge of the clock. In 12-bit mode, multiple clocking options exist: with a signal clock, data will be clocked on the falling and the rising edge; with dual clocks data can be clocked on either the falling edge of the rising edge of both clocks.
3.13 Onboard Ethernet Controller
The onboard Intel 82559B Ethernet contr oller features the following:
PCI local bus
IEEE802.3u auto-negotiation for automatic speed selection
10/100Mbps operation in a single port PCI bus master architecture
Wake On LAN function support
Chapter 4 Configuring the Motherboard
The following sections describe the necessary procedures and proper jumper settings to configure the LI7WM motherboard. For the locations of the jumpers, refer to Figure 2.
4.1 CPU Frequency Selection .............................................................15
4.2 Clear CMOS Select: JP5 .............................................................15
4.3 Onboard Audio Enable/ Disable: JP2.........................................16
4.4 Onboard Lan Enable/ Disable: JP3 ..............................................16
The following examples show the conventions used in this chapter.
Jumper Open
Jumper
Closed/Short
1 2
4.1 CPU Frequency Selection
Setting CPU Speed in the BIOS Setup
The LI7WM motherboard allows users to set the CPU speed through the BIOS Setup. The parameters used in configuring the CPU speed include CPU Clock Multiplier (X3, X3.5, X4, X4.5, X5, X5.5, X6, X6.5, X7, X7.5, X8) and CPU Clock (66MHz, 68MHz, 75MHz, 83MHz or 100MHz, 103MHz, 112MHz, 133MHz).
In the initial setup, the system automatically detects the base Frequency of the CPU (66MHz or 100MHz/133MHz). Under
the under CPU Speed Setting section, use the and ↓ keys to easily change the CPU speed or press the PageUp or PageDown key to see more options.
Overclocking could cause the system not to boot in the process of setting the CPU speed. When this happens, turn off the computer by pressing the power button and turn it on again by pressing the Insert key and the power button simultaneously. When the system is turned on, press the Delete key to enter BIOS Setup and configure the CPU speed.
4.2 Clear CMOS Select: JP5
Use JP5, to clear the contents of the CMOS RAM. Do not clear the CMOS RAM unless it is absolutely necessary. Before clearing CMOS, you should disconnect the ATX-power connector from the motherboard.
JP5 Jumper Setting Function
pin 1-2: short Clear CMOS
3
1 2 3
pin 2-3: short Normal
Chapter 4 Configuring the Motherboard
1 2
1 2
4.3 JP2: Onboard Audio Enable/Disable
Onboard AC ’97 codec support the Audio function. Please refer to the default jumper setting before you proceeding with system installation.
JP2 Jumper Setting Function
Onboard Audio
Disabled
pin 1-2: short
3
1 2 3
pin 2-3: short
4.4 JP3: Onboard Lan Enable/Disable
JP2, a 3-pin header, is the onboard Intel 82559B Ethernet controller. Please refer to the default jumper setting before you proceeding with system installation.
JP3 Jumper Setting Function
pin 1-2: short
Onboard Audio
Enabled
Onboard LAN
Disabled
3
Onboard Audio
Enabled
1 2 3
pin 2-3: short
Chapter 7 Audio Driver Installation Guide
Figure 1: Layout of the LI7WM Motherboard
19 LI7WM User’s Manual
Chapter 6 BIOS and System Setup
Chapter 5 Installation
This chapter describes the interface that the LI7WM provides for creating a working system. Refer to Figure 3 for the location of the connectors.
The following items are covered in this chapter:
5.1 I/O Connectors................................................................................20
5.2 J1: S-VHS Connector.....................................................................20
5.3 J2: RCA Connector........................................................................20
5.4 J3: Panel Link Connector ............................................................21
5.5 J4: CRT Connector.........................................................................21
5.6 J5: USB Connector.........................................................................22
5.7 J6/J7: PS/2 Keyboard and PS/2 Mouse Connectors .................22
5.8 J8/J9: Serial Ports ...........................................................................23
5.9 J10: Parallel Port Connector.........................................................23
5.10 J11: RJ45 Connector ..................................................................24
5.11 J12, J13, J14: Line Out, Line In, Mic Connectors ..................24
5.12 J15: IrDA Connector....................................................................24
5.13 J16: WOL(Wake On Lan)Connector........................................24
5.14 J17: Game Port Connector..........................................................25
5.15 J18: Chassis Fan Power Connector...........................................25
5.16 J19: Front Bezel Connector........................................................25
5.17 J20: ATX Power Supply Connector..........................................26
5.18 J21: Floppy Drive Connector.....................................................26
5.19 J22, J23: IDE1 and IDE2 Connectors .......................................27
5.20 J24, J25: CD-ROM Audio In Connectors................................28
5.21 J26: Chassis Fan Power Connector...........................................28
5.22 J27: CPU Fan Power Connector................................................28
5.23 J28: Reset Switch .........................................................................28
Chapter 6 BIOS and System Setup
5.24 JP1: TV-Out: PAL/NTSC ...........................................................29
5.25 JP2: Onboard Audio In Connector............................................29
5.26 JP3: Onboad Lan Enable/ Disable .............................................29
5.27 JP4: Boot Block Lock/Unlock ...................................................30
5.28 JP5: Clear CMOS Select .............................................................30
5.29 S1: BL7WM Riser Card Connector ......................................30
Chapter 6 BIOS and System Setup
5.1 I/O Connectors
The I/O connectors connect the LI7WM to the most common peripherals. To attach cables to these connectors, carefully align Pin 1 of the cables to that of the connectors. Refer to Figure 4 for the location and orientation of the connectors.
Figure 4: Orientation of the I/O Connector
5.2 J1: S-VHS Connector
The J1 S-VHS connector is for the TV -Out feature of the onboard VGA controller. Below are the pin-out assignments of the connectors.
Pin # Signal Name
1 Ground 2 Ground 3 Luma Output 4 Chroma Output
5.3 J2: RCA Connector
The J2 RCA connector is for the TV -Out feature of the onboard VGA controller.
Chapter 6 BIOS and System Setup
5.4 J3: Panel Link Conne ctor (option)
Below are the pin-out assignments of the connectors.
Signal Name Pin # Pin # Signal Name
TXOUT 1+ 1 11 TXOUT 2+
TXOUT 1- 2 12 TXOUT 2-
Ground 3 13 Ground Ground 4 14 Ground
TXCLKOUT+ 5 15 TXOUT 0+
TXCLKOUT- 6 16 TXOUT 0-
Ground 7 17 No Connect
Vcc 8 18 Panel detection No Connect 9 19 Panel ID SDA No Connect 10 20 Panel ID SCL
5.5 J4: CRT Connector
J4 is a DB-15 VGA connector. The following table shows the pin-out assignments of this connector.
Signal Name Pin # Pin # Signal Name
Red 1 2 Green
Blue 3 4 N.C. Ground 5 6 Ground Ground 7 8 Ground
+5V 9 10 Ground
N.C. 11 12 Monitor ID SDA
HSYNC 13 14 VSYNC
Monitor ID SCL 15
Chapter 6 BIOS and System Setup
5.6 J5: USB Connector
J5 is the standard USB external connector consisting of two ports. USB support allows connections of up to 64 plug and play external peripherals per channel. The following table shows the pin outs of these ports.
PORT 2
Pin # Signal Name
1 Vcc 2 USB­3 USB+
PORT 1
4 Ground
5.7 J6/J7: PS/2 Keyboard and PS/2 Mouse Connectors
PS/2 Mouse
PS/2 Keyboard
Below are the pin-out assignments of the connectors.
Signal Name Keyboard Mouse Signal Name
Keyboard data 1 1 Mouse data
No Connect 2 2 No Connect
Ground 3 3 No Connect
5V 4 4 5V
Keyboard clock 5 5 Mouse Clock
No Connect 6 6 No Connect
Chapter 6 BIOS and System Setup
5.8 J8/J9: Serial Ports
The onboard serial ports of the LI7WM are two DB-9 external connectors.
COM1 Serial Port
COM2 Serial Port
The table below shows the pin-out assignments of these connectors.
Signal Name Pin # Pin # Signal Name
DCD, Data carrier detect 1 6 DSR, Data set ready
RXD, Receive data 2 7 RTS, Request to send
TXD, Transmit data 3 8 CTS, Clear to send
DTR, Data terminal ready 4 9 RI, Ring indicator
GND, ground 5 10 Not Used
5.9 J10: Parallel Port Connector
J10 is a DB-25 external connector as seen in the above figure. The following table describes the pin- out assignments of this connector.
Signal Name Pin # Pin # Signal Name
Line printer strobe 1 14 AutoFeed PD0, parallel data 0 2 15 Error PD1, parallel data 1 3 16 Initialize PD2, parallel data 2 4 17 Select PD3, parallel data 3 5 18 Ground PD4, parallel data 4 6 19 Ground PD5, parallel data 5 7 20 Ground PD6, parallel data 6 8 21 Ground PD7, parallel data 7 9 22 Ground
ACK, acknowledge 10 23 Ground
Busy 11 24 Ground
Paper empty 12 25 Ground
Select 13 N/A N/A
Chapter 6 BIOS and System Setup
5.10 J9: RJ45 Connector (option)
This connector is for the 10/100Mbps Ethernet capability of the CPU card. The figure below shows the pin out assignments of this connector and its corresponding input jack.
TD+(pin#1) TD-(pin#2) RD+(pin#3)
RD-(pin#6)
5.11 J10, J11, J12: Line Out, Line In, Mic Connectors
The Line Out (J12), Line In (J13) and Mic (J14) connectors, as shown in the figure below, are used in conjunction with the audio function of the onboard audio controller.
5.12 J15: IrDA Connector
This connector is used for an IrDA connector that supports infrared wireless communication.
+5V IRRX
IRTX
Pin # Signal Name
1 +5V 2 No connect 3 Ir RX 4 Ground 5 Ir TX
N.C. GND
5.13 WOL(Wake on LAN) Connector: J16
J16 is a 3-pin header for the Wake on LAN function. Wake on LAN will function properly only with an ATX power supply with 5VSB that has 200mA.
Pin # Signal Name
1 +5VSB
1 2 3
2 Ground 3 Wake on LAN
Chapter 6 BIOS and System Setup
5.14 J17: Game Port Connector
J17 is a 16-pin header connector for the game port cable that comes with the motherboard. It is part of the functions provided by the onboard audio controller.
Signal Name Pin # Pin # Signal Name
Vcc 1 9 Vcc
JOY4 2 10 JOY6
JOYTIME0 3 11 JOYTIME2
Ground 4 12 MIDI OUT Ground 5 13 JOYTIME3
JOYTIME1 6 14 JOY7
JOY5 7 15 MIDI IN
Vcc 8 16 No Connect
5.15 J18: Chassis Fan Power Connector
J26 is a 3-pin header for the chassis fan power connector. The fan must be a 12V fan.
Pin # Signal Name
1 2 3
1 Rotation 2 +12V 3 Ground
5.16 J19: Front Bezel Connectors
The front bezel of the case has a control panel that provides light indication of the computer activities and switches to change the computer status. J19 is an 8-pin header that provides the interfaces.
Pin # Signal Name
1 2 3 4 5 6 7 8
+5V
Ground
5VSB
LAN Active LED
+5V
IDE LED
Ground
Power Button
Chapter 6 BIOS and System Setup
5.17 J20: ATX Power Supply Connector
J20 should be used with an ATX power supply with 3.3V specification. Refer to the table below for the pin out assignments.
11 1
20 10
Signal Name Pin # Pin # Signal Name
3.3V 11 1 3.3V
-12V 12 2 3.3V
Ground 13 3 Ground
PS-ON 14 4 +5V Ground 15 5 Ground Ground 16 6 +5V Ground 17 7 Ground
-5V 18 8 Power good +5V 19 9 5VSB +5V 20 10 +12V
5.18 J21: Floppy Drive Connector
J21 of the LI7WM is a 34-pin header and will support up to 2.88MB floppy drives. The following table shows its pin-out assignments.
Signal Name Pin # Pin # Signal Name
Ground 1 2 RM/LC Ground 3 4 No connect Ground 5 6 No connect Ground 7 8 Index Ground 9 10 Motor enable 0 Ground 11 12 Drive select 1 Ground 13 14 Drive select 0 Ground 15 16 Motor enable 1 Ground 17 18 Direction Ground 19 20 Step Ground 21 22 Write data Ground 23 24 Write gate Ground 25 26 Track 00 Ground 27 28 Write protect Ground 29 30 Read data Ground 31 32 Side 1 select Ground 33 34 Diskette change
Chapter 6 BIOS and System Setup
5.19 J22, J23: IDE1 and IDE2 Connectors
J22: Primary IDE Connector
Signal Name Pin # Pin # Signal Name
Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5 6 Host data 9 Host data 5 7 8 Host data 10 Host data 4 9 10 Host data 11 Host data 3 11 12 Host data 12 Host data 2 13 14 Host data 13 Host data 1 15 16 Host data 14 Host data 0 17 18 Host data 15
Ground 19 20 Key
DRQ0 21 22 Ground
Host IOW 23 24 Ground
Host IOR 25 26 Ground
IOCHRDY 27 28 Host ALE
DACK0 29 30 Ground
IRQ14 31 32 No connect Address 1 33 34 Cable ID Address 0 35 36 Address 2
Chip select 0 37 38 Chip se lect 1
Activity 39 40 Ground
J23: Secondary IDE Connector
Signal Name Pin # Pin # Signal Name
Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5 6 Host data 9 Host data 5 7 8 Host data 10 Host data 4 9 10 Host data 11 Host data 3 11 12 Host data 12 Host data 2 13 14 Host data 13 Host data 1 15 16 Host data 14 Host data 0 17 18 Host data 15
Ground 19 20 Key
DRQ0 21 22 Ground
Host IOW 23 24 Ground
Host IOR 25 26 Ground
IOCHRDY 27 28 Host ALE
DACK1 29 30 Ground
MIRQ0 31 32 No connect Address 1 33 34 Cable ID Address 0 35 36 Address 2
Chip select 0 37 38 Chip select 1
Activity 39 40 Ground
Chapter 6 BIOS and System Setup
5.20 J24, J25: CD-ROM Audio In Connectors
J25 and J26 are the onboard CD-ROM audio in connectors. Below are their pin assignments.
1 2 3 4
J25
1 2 3 4
J24
Signal Name Pin # Pin # Signal Name
Ground 1 1 Right
Left 2 2 Ground
Ground 3 3 Ground
Right 4 4 Left
5.21 J26: Chassis Fan Power Connector
J26 is a 3-pin header for the chassis fan power connector. The fan must be a 12V fan.
Pin # Signal Name
1 2 3
1 Rotation 2 +12V 3 Ground
5.22 J27: CPU Fan Power Connector
J27 is a 3-pin header for the CPU fan pow er connector. The fan must be a 12V fan.
Pin # Signal Name
1 2 3
1 Rotation 2 +12V 3 Ground
5.23 J28: Reset Switch
The reset switch allows the user to reset the system without turning the main power switch off and then on again.
Chapter 6 BIOS and System Setup
5.24 JP1: TV-Out: PAL/ NTSC
Chrontel’s CH7007 digital PC to TV encoder is a stand-alone integrated circuit which provides a PC 99 compliant solution for TV output. It provides a universal digital input port to accept a pixel data stream from a compatible VGA controller (or equivalent) and converts this directly into NTSC or PAL TV format. Below are their pin assignments.
JP1 Function JP1 Function
PAL
On
Off
NTSC
5.25 JP2: Onboard Audio In Connector
JP2, a 3-pin header jumper, is used to enabled/disabled Onboard Software audio. Please refer to the following pin assignment.
JP2 Jumper Setting Function
pin 1-2: short
1 2 3
1 2 3
5.26 JP3: Onboard LAN Enable/Disable
JP3 supports the function of 82559B chip. The table below shows the pin assignments of this connector.
JP5 Setting LAN Function
pin 2-3: short
Onboard Audio
Disabled
Onboard Audio
Enabled
1 2 3
1 2 3
Pin 1-2 Enabled
Pin 2-3 Disabled
Chapter 6 BIOS and System Setup
5.27 JP4: Boot Block Lock/Unlock
When the Boot Block is locked, BIOS flash update cannot be executed.
JP4 Function JP4 Function
On
Boot Block
Unlock
Off
Boot Block
Locked
5.28 JP5: Clear CMOS Select
Use JP5, a 3-pin header, to clear the contents of the CMOS RAM. Do not clear the CMOS RAM unless it is absolutely necessary. You will lose your password, etc.
JP5 Jumper Setting Function
pin 1-2: short Clear CMOS
1 2 3
Follow the steps below to clear CMOS data.
1. Disconnect the AC power cord.
2. Short JP12 (1-2) and wait for 3 seconds.
3. Short JP12 (2-3) and replace the AC power cord.
4. Turn on the system.
1 2 3
pin 2-3: short Normal
5.29 S1: BL21PI Riser Card Connector
J17 is a slot connector for the BL21PI riser card that comes with the LI7WM motherboard. The riser card comes with one PCI slot.
Chapter 6 BIOS and System Setup
Chapter 6 BIOS and System Setup
This chapter describes the different settings available in the Award BIOS. The topics covered in this chapter are as follows:
6.1 BIOS Introduction ..........................................................................35
6.2 BIOS Setup......................................................................................35
6.3 Standard CMOS Setup...................................................................37
Date....................................................................................................37
Time ...................................................................................................38
Primary HDDs / Secondary HDDs ...............................................38
Drive A / Drive B.............................................................................38
Video..................................................................................................39
Halt On ..............................................................................................39
6.4 BIOS Features Setup......................................................................40
Virus Warning..................................................................................40
CPU Internal Cache / External Cache..........................................40
CPU L2 Cache ECC Checking ......................................................40
Quick Power On Self Test..............................................................41
First/ Secnd/ Third Boot Device................................................... 41
Boot other Device............................................................................41
Swap Floppy Drive..........................................................................41
Boot Up Floppy Seek......................................................................41
Boot Up NumLock Status ..............................................................41
Boot Up System Speed...................................................................41
Gate A20 Option..............................................................................41
Typematic Rate Setting...................................................................41
Typematic Rate (Chars/Sec) ..........................................................42
Typematic Delay (Msec) ................................................................42
Security Option................................................................................42
OS Select for DRAM > 64MB......................................................42
Report No FDD For WIN 95 .........................................................42
6.5 Advanced Chipset Features Setup ...............................................43
SDRAM CAS Latency Time.........................................................43
Bank DRAM Timing Trac/Trc ......................................................43
SDRAM RAS-to-CAS Delay........................................................43
SDRAM RAS Precharge Time......................................................43
System BIOS Cacheable.................................................................44
Video BIOS Cacheable...................................................................44
Memory Hole at 15MB - 16MB ....................................................44
CPU-Lantency Timer ....................................................................44
Delayed Transaction........................................................................44
Chapter 6 BIOS and System Setup
OnChip Video Window Size .........................................................44
Onboard Display Cache Setting....................................................44
6.6 Intergrated Perphierals ................................................................45
Onchip Primary/Secondry PCI IDE ..........................................45
IDE Primary/Secondary Master /Slave PIO................................45
IDE Primary/Secondary Master /Slave UDMA .........................46
USB Controller ..............................................................................46
USB Keyboard Suppory ...............................................................46
Init Display First ............................................................................46
AC97 Video......................................................................................46
AC97 Modem .................................................................................46
IDE HDD Block Modem ..............................................................46
Power on Function .........................................................................46
Onboard FDD Controller................................................................46
Onboard Serial/Parallel Port ........................................................47
UART Mode select..........................................................................47
Onboard Parallel Port......................................................................47
RxD, TxD Delay..............................................................................47
UR2 Duplex mode...........................................................................47
Use IR Pins ...................................................................................47
PWRON after PW -Fail ...................................................................47
Game Adress .....................................................................................47
Midi Port Adress..............................................................................47
Midi Port IRQ...................................................................................47
6.7 Power Management Set .................................................................48
ACPI Function..................................................................................48
ACPI Suspend Type........................................................................48
Power Management .......................................................................48
Video Off Method............................................................................49
Video Off in Suspend ....................................................................49
Suspend Type...................................................................................49
Modem Use IRQ..............................................................................49
Suspend Mode...............................................................................49
HDD Power down ............................................................................49
Safe-Off by PWR-BTTN............................................................49
Wake-Up by PCI Card ..................................................................49
PWR On by Modem/Lan ..............................................................50
CPU Thermal-Throttling ..............................................................50
Resume by Alarm ..........................................................................50
Reload Global Timer Events .......................................................50
6.8 PNP/PCI C onfiguation .................................................................51
Reset Configuation Date ..............................................................51
Chapter 6 BIOS and System Setup
Resource Controller By ................................................................51
IRQ Resource...................................................................................51
PCI/VGA Palette Snoop.................................................................51
6.9 PC Health Status ...........................................................................52
Tempreature/ Fan Speeds/ Voltage .............................................52
Shutdown Tempreature...................................................................52
6.10 Frequency/ Voltage Control.......................................................52
Auto Detect DIMM/PCI Clk..........................................................53
Spread Sprctum ..............................................................................53
Host CPU/PCI Clock.......................................................................53
CPU Clock Ratio ..............................................................................53
6.11 Lord Fail- Safe Default ...............................................................54
6.12 Lord Optimized Default ..............................................................54
6.13 Set Superior/ User Password ......................................................55
6.14 Save & Exit Setup ........................................................................56
6.15 Exit Without Savin g.....................................................................56
Chapter 6 BIOS and System Setup
6.1 BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Celeron processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
6.2 BIOS Setup
The Award BIOS provides a Setup utility program for specifying the system configurations and settings. The BIOS ROM of the system stores the Setup utility. When you turn on the computer, the Award BIOS is immediately activated. Pressing the <Del> key immediately allows you to enter the Setup utility. If you are a little bit late pressing the <Del> key, POST (Power On Self Test) will continue with its test routines, thus preventing you from invoking the Setup. If you still wish to enter Setup, restart the system by pressing the ”Reset” button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the system Off and back On again. The following message will appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to select, the <PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit. When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices.
Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit á â à ß : Select Item F10 : Save & Exit Setup
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
Time, Date, Hard Disk Type…
Chapter 6 BIOS and System Setup
After making and saving system changes with Setup, you
ot boot, the Award BIOS
supports an override to the CMOS settings that resets your
We strongly recommend that you avoid making any changes to the chipset defaults. These defaults have been carefully
system manufacturer to
The section below the setup items of the Main Menu displays the control keys fo r this menu. Another section at the bottom of the Main Menu just below the control keys section displays information on the currently highlighted item in the list.
NOTE:
find that your computer cann
system to its default.
chosen by both Award and your provide the absolute maximum performance and reliability.
Chapter 6 BIOS and System Setup
6.3 Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Standard CMOS Features
Date (mm:dd:yy) Tue, Mar 26 1999 Item Help Time (hh:mm:ss) 00 : 00 : 00 Menu Level
IDE Primary Master Press Enter 13020 MB Change the day, month, IDE Primary Slave Press Enter None Year and century IDE Secondary Master Press Enter None IDE Secondary Slave Press Enter None
Drive A 1.44M, 3.5 in. Drive B None
Video EGA/VGA Halt On All Errors Base Memory 640K Extended Memory 129024K Total Memory 130048K
At the bottom of the menu are the control keys for use on this menu. If you need any help in each item field, you can press the <F1> key. It will display the relevant information to help you. The memory display at the lower right-hand side of the menu is read-only. It will adjust automatically according to the memory changed. The following describes each item of this menu.
Date
The date format is:
Day : Sun to Sat Month : 1 to 12 Date : 1 to 31 Year : 1994 to 2079
To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time.
Chapter 6 BIOS and System Setup
The specifications of your drive must match with the drive table. The hard disk will not work properly if you enter
correct information in these fields. If your hard disk drive
type is not matched or listed, you can use Type User to define
Time
The time format is: Hour : 00 to 23
Minute : 00 to 59 Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/- keys to set the current time.
IDE Primary HDDs / IDE Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. Each channel can support up to two hard disks; the first is the “Master” and the second is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto, Manual, and None. Select ‘Manual’ to define the drive information manually. You will be asked to enter the following items.
CYLS : Number of cylinders HEAD : Number of read/write heads PRECOMP : Write precompensation LANDZ : Landing zone SECTOR : Number of sectors SIZE : Automatically adjust according to the configuration
The Access Mode selections are as follows: Auto
Normal (HD < 528MB) Large (for MS -DOS only) LBA (HD > 528MB and
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has been installed in the computer. The available specifications are: 360KB
5.25 in.
NOTE:
1.2MB
5.25 in.
720KB
3.5 in.
1.44MB
3.5 in.
in
your own drive type manually.
supports Logical Block Addressing)
2.88MB
3.5 in.
Chapter 6 BIOS and System Setup
The system boot will not be halted for any
fatal error,
the system will stop and you will be
The system boot will not be halted for a
The system boot will not be halted for a disk
Video
This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters.
Halt On
This field determines whether or not the system will halt if an error is detected during power up. No errors
error that may be detected.
All errors Whenever the BIOS detects a non-
prompted.
All, But Keyboard
keyboard error; it will stop for all other errors
All, But Diskette
error; it will stop for all other errors.
All, But Disk/Key The system boot wi ll not be halted for a key-
board or disk error; it will stop for all others.
Chapter 6 BIOS and System Setup
Many disk diagnostic programs, which attempt to access the
or table, can cause the virus warning. If you will run
6.4 Advanced BIOS Features Setup
This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
Virus Warning CPU Internal Cache Enabled Menu Level
External Cache Enabled CPU L2 Cache ECC Checking Enabled Quick Power On Self Test Enabled First Boot Device Floppy Second Boot Dev ice HDD-0 Third Boot Device LS/ZIP Boot Other Device Enabled Swap Floppy Drive Disabled Boot Up Floppy Seek Disabled Boot Up Numlock Status On Gate A20 Option Fast Typematic Rate Setting Disabled Typematic Rate (chars/Sec) 6 Typematic Delay (Msec) 250 Security Option Setup OS Select For DRAM>64MB Non-OS2 Report No FDD For WIN 95 Yes
Virus Warning
This item protects the boot sector and partition table of your hard disk against accidental modifications. If an attempt is made, the BIOS will halt the system and display a warning message. If this occurs, you can either allow the operation to continue or run an anti-virus program to locate and remove the problem.
NOTE:
CPU Internal Cache / External Cache
Cache memory is additional memory that is much faster than conventional DRAM (system memory). CPUs from 486-type on up contain internal cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for even faster access by the CPU. These items allow you to enable (speed up memory access) or disable the cache function. By default, these items are Enabled.
CPU L2 Cache ECC Checking
This field enables or disables the ECC (Error Correction Checking) checking of the CPU level -2 cache. The default setting is Enabled.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Advanced BIOS Features
Disabled ITEM HELP
boot sect such a program, disable the Virus Warning feature.
Allows you choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep
Chapter 6 BIOS and System Setup
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items.
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an operating system. The options available include Floppy, LS/ZIP, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, LAN and Disable.
Boot Other Device
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy Drive. When enabled, the BIOS swaps floppy drive assignments so that Drive A becomes Drive B, and Drive B becomes Drive A. By default, this field is set to Disabled.
Boot Up Floppy Seek
When enabled, the BIOS will seek whether or not the floppy drive installed has 40 or 80 tracks. 360K type has 40 tracks while 760K,
1.2M and 1.44M all have 80 tracks. By default, this field is set to Enabled.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the system. By default, the system boots up with NumLock On.
Boot Up System Speed
This has no function and selects the default system speed (High).
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a device used to address memory above 1 MB. The default setting is Fast.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will generate only one instance. When enabled, you can set the two typematic controls listed next. By default, this field is set to Disabled.
Chapter 6 BIOS and System Setup
Typematic Rate (Chars/Sec)
When disabled, continually holding down a ke y on your keyboard will generate only one instance. When enabled, you can set the two
typematic controls listed next. By default, this field is set to Disabled.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default value is Setup. When you select System, the system prompts for
the User Password every time you boot up. When you select Setup, the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM memory when used with OS/2 that depends on certain BIOS calls to access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
This option allows Windows 95 to share with other peripherals IRQ6, which is assigned to a floppy disk drive if the drive is not exist.
Chapter 6 BIOS and System Setup
6.5 Advanced Chipset Features Setup
This Setup menu controls the configuration of the motherboard chipset.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
SDRAM CAS Latency Time Auto ITEM HELP SDRAM Cycle Time Tras/Trc 6/8 Menu Level
SDRAM RAS-to-CAS Delay 3 SDRAM RAS Precharge Time 3 System BIOS Cacheable Enabled Video BIOS Cacheable Enabled Memory Hole At 15M-16M Disabled CPU Latency Timer Enabled Delayed Transaction Enabled On-Chip Video Window Size 64MB
* Onboard Display Cache Setting * CAS# Latency 3 Paging Mode Control Open RAS-to-CAS Override By CAS# LT RAS# Timing Fast RAS# Precharge Timing Fast
Advanced Chipset Features
SDRAM CAS Latency Time You can select CAS latency time in HCLKs of 2/2 or 3/3. The system board designer should set the values in this field, depending on the DRAM installed. Do not change the values in this field unless you change specifications of the installed DRAM or the installed CPU. The choices are Auto, 2 and 3.
SDRAM Cycle Time Tras/Trc The settings available for the SDRAM Cycle Time Tras/Trc are 6/8 and 5/7. The default setting is 6/8.
SDRAM RAS-to-CAS Delay You can select RAS to CAS Delay time in HCLKs of 2/2 or 3/3. The system board designer should set the values in this field, depending on the DRAM installed. Do not change the values in this field unless you change specifications of the installed DRAM or the installed CPU. The choices are 2 and 3.
SDRAM RAS Precharge Time This option defines the length of time for Row Address Strobe is allowed to precharge. The choices are 2 and 3.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at F000h-FFFFFh, resultin g in better system performance. However, if any program writes to this memory area, a system error may result.
Chapter 6 BIOS and System Setup
Video BIOS Cacheable
The Setting Enabled allows caching of the video BIOS ROM at C0000h-F7FFFh, resulting in better video performance. However, if any program writes to this memory area, a system error may result.
Memory Hole At 15M -16M
In order to improve performance, certain space in memory can be reserved for ISA cards. This memory must be mapped into the memory space below 16 MB. The choi ces are Enabled and Disabled.
CPU Latency Timer
This field enable or disable the CPU latency timer. The default setting is Enabled.
Delayed Transaction
The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1.
On-Chip Video Window Size
The setting choices for the On-Chip Video Window Size are 64MB and 32MB. By default, this option is set to 64MB.
Onboard Display Cache Setting
The default setting and optional setting for the onboard display cache functions are as follows:
CAS# Latency 3(default), 2(option) Paging Mode Control Open (default), Close (option) RAS-to-CAS Override by CAS# LT (default), Override (2)(option) RAS# Timing Fast (default) , Slow (option) RAS# Precharge Timing Fast (default), Slow (option)
Chapter 6 BIOS and System Setup
6.6 Integrated Peripherals
This section sets configurations for your hard disk and other integrated peripherals.
On-Chip Primary PCI IDE On-Chip Secondary PCI IDE IDE Primary Master PIO IDE Primary Slave PIO IDE Secondary Master PIO IDE Secondary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA IDE Secondary Master UDMA IDE Secondary Slave UDMA USB Controller USB Keyboard Support Init Display First PCI Slot AC97 Audio Enabled AC97 Modem Disabled IDE Block Mode Enabled POWER ON Function Button Only KB Power ON Password Enter Hot Key Power ON Ctrl-F1 Onboard FDC Controller Enabled Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 UART Mode Select Normal RxD, TxD Active Hi, Lo IR Transmission Delay Enabled UR2 Duplex Mode Half (Full) Use IR Pins IR, Rx2Tx2 Onboard Parallel Port 378/IRQ7 Parallel Port Mode SPP EPP Mode Select EPP1.7 ECP Mode Use DMA 3 PWRON After PWR-Fail Off Game Port Address 201 Midi Port Address 330 Midi Port IRQ 10
OnChip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate the channels.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster. Rather than have the BIOS issue a series of commands that transfer to or from the disk drive, PIO (Programmed Input/Output) allows the BIOS to communicate with the controller and CPU directly. The system supports five modes, numbered from 0 (default) to 4, which primarily differ in timing. When Auto is selected, the BIOS will select the best available mode.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Advanced Chipset Features
Enabled ITEM HELP Enabled Menu Level Auto Auto Auto Auto Auto Auto Auto Auto Enabled Disabled
Chapter 6 BIOS and System Setup
IDE Primary/Secondary Master/Slave UDMA
USB Controller
The options for this field are Enabled and Disabled. By default, this field is set to Enabled.
USB Keyboard Support
By default, the USB Keyboard Support fiel d is set to Disabled.
Init Display First
This field allows the system to initialize first the VGA card on chip or the display on the PCI Slot. By default, the PCI Slot VGA is initialized first.
AC97 Audio
By default, the AC97 Audio is set to Enabled.
AC97 Modem
By default, the AC97 Modem is set to Disabled.
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive.
POWER ON Function
This field allows powering on by the following methods:
Password Keyboard 98 Hot KEY BUTTON ONLY
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the motherboard and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field. This option allows you to select the onboard FDD port.
Chapter 6 BIOS and System Setup
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial and parallel ports and their addresses. The default values for these ports are: Serial Port 1 3F8/IRQ4 Serial Port 2 2F8/IRQ3 Parallel Port 378H/IRQ7
UART Mode Select
This field determines the UART mode in your computer. The default value is Normal. Other options include IrDA and ASKIR.
Onboard Parallel Port
The setting for this field are 378/IRQ7, 278/IRQ5, 2BC/IRA7 and Disabled. By default, the onboard parallel port is set to 378/IRQ7.
Onboard Parallel Port
The setting for this field are 378/IRQ7, 278/IRQ5, 2BC/IRA7 and Disabled. By default, the onboard parallel port is set to 378/IRQ7 .
RxD, TxD Active
The settings for this field are Hi,Lo, Lo,Hi, Lo,Lo, and Hi,Hi.
IR Transmission Delay
By default, this field is set to Enabled.
UR2 Duplex Mode
The settings available for this field are Half (default) and Full.
Use IR Pins
The settings for this field are IR, Rx2Tx2 (default) and RxD2, TxD2.
PWRON After PW -Fail
In case of power failure, the system can be configured to power on or to remain off when the power returns. These two settings are Former-Sts and Off respectively. The default setting for this field is Off.
Game Port Address
The settings for this field are 201 (default), 209 and Disabled.
Midi Port Address
The option settings for this field are 330, 300, 290 and Disabled. The default setting is 330.
Midi Port IRQ
The option settings for this field are 5 and 7. The default setting is 7.
Each of the ranges is from 1 min. to 1hr. Except for HDD Power Down which
6.7 Power Management Setup
The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn off video display after a period of inactivity.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
ACPI Function ACPI Suspend Type
Power Management Video Off Method Video Off In Suspend Suspend Type Modem Use IRQ Suspend Mode HDD Power Down Soft-Off by PWR-BTTN
Wake-Up by PCI Card PW On by Modem/LAN CPU Thermal-Throttling
Resume by Alarm Date (of Month) Alarm 0 Time (hh:mm:ss) Alarm 0
** Reload Global Timer Events ** Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD, COM, LPT Port Disabled PCI PIRQ[A-D] # Disabled
ACPI Function
This field allows you to enable or disable the ACPI (Advanced Configuration Power Interface) function on the motherboard. By default, this field is set to Disabled
ACPI Suspend Type
Power Management
This field allows you to select the type of power saving management modes. There are four selections for Power Management.
Min. Power Saving Minimum power management Max. Power Saving Maximum power management. User Define
Chapter 6 BIOS and System Setup
Power Management Setup
Enabled ITEM HELP S1 (POS) Menu Level
User Define DPMS Yes Stop Grant 3 Disabled Disabled Instant-Off
Disabled Enabled
62.5% Disabled
ranges from 1 min. to 15 min. (Default)
Chapter 6 BIOS and System Setup
rotection feature, the
NOTE:
In order to enable the CPU overheat p Power Management field should not be set to Disabled.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank Default setting, blank the screen and turn
off vertical and horizontal scanning.
DPMS Allows the BIOS to control the video
display card if it supports the DPMS feature.
Blank Screen This option only writes blanks to the video
buffer.
Video Off in Suspend
When enabled, the video is off in suspend mode. The default setting is Yes.
Suspend Type
The settings for this field are Stop Grant (default) and PwrOn Suspend.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the IRQ used is
3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active.
Soft-Off by PWR-BTTN
This field defines the power-off mode when using an ATX power supply. The Instant Off mode allows powering off immediately upon pressing the power button. In the Delay 4 Sec mode, the system powers off when the power button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds. The
default value is Instant Off.
Wake-Up by PCI Card
The settings for this field are Enabled and Disabled (default).
Chapter 6 BIOS and System Setup
PWR On by Modem/LAN
This field enables or disables the power on of the system through the modem connected to the serial port or LAN.
CPU Thermal-Throttling
The CPU Thermal Throttling function, by default, is set to 62.5%
Resume by Alarm
This field enables or disables the resumption of the system operation. When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode. When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service.
Chapter 6 BIOS and System Setup
6.8 PNP/PCI Configuration
This option configures the PCI bus system . All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By IRQ Resources
PCI/VGA Palette Snoop
Reset Configuration Data
This field allows you to determine whether to reset the configuration data or not. The default value is Disabled.
Resources Controlled By
The settings for this field are Auto (ESCD) (default) and Manual.
IRQ Resources
To configure the IRQ Resources, the Resource Controlled By field should be set to Manual.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly. This field allows you to set whether or not MPEG ISA/VESA VGA Cards can work with PCI/VGA. When this field is enabled, a PCI/VGA can work with an MPEG ISA/VESA VGA card. When this field is disabled, a PCI/VGA cannot work with an MPEG ISA/VESA Card.
Disabled ITEM HELP
Auto (ESCD) Press Enter
Disabled
Menu Level
Default is Disabled. Select Enabled to reset
Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the OS cannot boot
Chapter 6 BIOS and System Setup
6.9 PC Health Status
This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
CPU Warning Temperature 66°C/151°F Current System Temp. 32°C/89°F Current CPU Temperature 38°C/100°F Current CPUFAN Speed Current AMR/PCI Speed
Current Chassis FAN Speed VCCP(V) +1.8V(V) +3.3V (V) + 5 V
+12 V
-12 V
- 5 V VBAT (V) 5VSB (V) 5.29 V Shutdown Temperature
PC Health Status
4470 RPM 0 RPM 0 RPM
1.98 V
1.76 V
3.34 V
4.97 V
11.91V
12.03V
5.04 V
3.50 V
75°C/167°F
ITEM HELP
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware mo nitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status.
Shutdown Temperature
This field allows the user to set the temperature by which the system automatically shuts down once the threshold temperature is reached. This function can help damage to the system that is caused by overheating.
6.10 Frequency/Voltage Control
This section shows the user how to configure the key components.
Auto Detect DIMM/PCI Clk Spread Spectrum
Host CPU/PCI Clock CPU Clock Ratio
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Frequency/Voltage Control
Disabled ITEM HELP Disabled
Default X3
Menu Level
Chapter 6 BIOS and System Setup
The above setup is for Intel 810E chipset use only. For motherboards with Intel 810 (MI6WBML), the options for Spread Spectrum and Host CPU/PCI Clock are not available. An extra
ng for the
CPU Clock is 66MHz~150MHz, while the settings for Spread
Auto Detect DIMM/PCI Clk
The settings for this field are Enabled and Disabled (default).
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only.
Host CPU/PCI Clock
The Host CPU/PCI Clock has a default setting of Default which is either 66/33MHz or 100/33MHz as automatically detected by the
system. The options are as follows: For CPU with 66MHz FSB, the options are 66/33MHz (Default), 75/37MHz, and 80/40 MHz. For CPU with 100MHz FSB, options are 100/33MHz (Default), 112/37MHz, 117/39MHz, 129/43MHz, 133/33MHz, 138/46MHz, 140/35MHz, 150/37MHz, 166/41MHz, 180/30MHz, 190/31MHz and 200/33MHz.
NOTE: Overclocking could cause the system not to boot. When this
happens, turn off the computer by pressing the power button and turn it on again by pressing the Insert key and the power
button simultaneously. Then press the Delete key to enter BIOS Setup and configure the CPU speed.
CPU Clock Ratio
The CPU Ratio, also known as the CPU bus speed multiplier, can be configured as 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, and 8.
option is the CPU Clock/SpreadSpectrum . The setti Spectrum are off and on.
Chapter 6 BIOS and System Setup
6.11 Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features.
Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit á â à ß : Select Item
F10 : Save & Exit Setup
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Load Fail-Safe Defaults
6.12 Load Optimized Defaults
This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features.
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Load Optimized Defaults
Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit á â à ß : Select Item F10 : Save & Exit Setup
Chapter 6 BIOS and System Setup
6.13 Set Supervisor/User Password
These two options set the system password. Supervisor Passw ord sets a password that will be used to protect the system and Setup utility. User Password sets a password that will be used exclusively on the system. To specify a password, highlight the type you want and press <Enter>. The Enter Password: message prompts on the screen. Type the password, up to eight characters in length, and press <Enter>. The system confirms your password by asking you to type it again. After setting a password, the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted to enter the password. A message will confirm the password to be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.
Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password P nP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit á â à ß : Select Item F10 : Save & Exit Setup
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Chapter 6 BIOS and System Setup
6.14 Save & Exit Setup
This option allows you to determine whether or not to accept the modifications. If you type “Y”, you will quit the setup utility and save all changes into the CMOS memory. If you type “N”, you will return to Setup utility.
Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit á â à ß : Select Item F10 : Save & Exit Setup
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Save & Exit Setup
6.15 Exit Without Saving
Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return you to Setup utility.
Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit á â à ß : Select Item F10 : Save & Exit Setup
CMOS Setup Utility – Copyright © 1984-1999 Award Software
Exit Without Saving
Chapter 7 Audio Driver Installation Guide
Chapter 7 Audio Driver Installation Guide
This chapter describe the audio driver installation procedure for the onboard Intel 810E + AC97. With a PCI Bus Mastering interface with DOS compatibility, it supports 32 voices wavetable, surround sound, 3D audio, and audio effects such as reverb and chorus. Creative Labs ES1373 uses single, shareable PCI interrupt and is AC97 compliant.
For normal operations and to maximize the audio functions of the motherboard, follow the audio driver installation procedure below.
Installing The Audio Drivers For Windows 95/98
For Analog Device AC97 Codec Audio Driver (CD Ver. 1.8)
If the CD that comes with your motherboard is Ver. 1.8, complete steps 1-4. If the CD is Ver. 1.9, run the setup.exe file which is located in the directory \Intel\i810\sound\AD1881 of the CD and the Welcome screen will appear. (Refer to step 3.)
1. After you have installed Windows 95/98, install the Intel 82810 audio driver. Insert the driver disk provided with the motherboard. Once it is inserted, the following screen appears.
1.
58 LI7WM User’s Manual
Chapter 7 Audio Driver Installation Guide
2. Click Intel M/B Drivers and the following screen appears.
3. Click Intel 82810 Drivers, then Intel 82810 PCI Multimedia Audio
Driver. When the Welcome screen appears, click Next to start
copying files.
Chapter 7 Audio Driver Installation Guide
4. Confirm the remove command by clicking OK.
Chapter 7 Audio Driver Installation Guide
This page was intentionally left blank.
Chapter 8 VGA Driver Installation Guide
Chapter 8 VGA Driver Installation Guide
This chapter describes the VGA onboard with the installation procedures necessary to take advantage of the features of the ATI 3D RAGE LT PRO. The topics covered in this chapter are as follows:
8.1 Introduction.....................................................................................63
8.2 Windows 95/98 Driver Installation .............................................64
8.3 Windows NT 4.0 Driver Installation...........................................66
LI7WM User’s Manual 62
Chapter 8 VGA Driver Installation Guide
8.1 Introduction
The onboard ATI 3D RAGE LT PRO utilizes AGP (Accelerated Graphics Port) bus to achieve rich 3D and video graphics display. It enables 3D graphics capabilities including support for z-buffering, alpha blending and faster texture mapping. Onboard TV-out connectors support S-VHS and RCA specifications. The unique features of the 3D RAGE LT PRO are as follows:
TV-Out. An integrated TV encoder with on-chip triple-DAC
allows simultaneous CRT/LCD/TV output.
Dual CRT Controller Support. Two independent CRT
controllers support two asynchronous simultaneous displays (LCD/CRT, CRT/TV)
Floating-Point Set-up Engine. The 3D RAGE LT PRO
integrates a floating-point set-up engine capable of processing up to 1.2 million triangles per second. By off-loading the set -up function from the CPU, allowing it to focus on 3D geometry and lighting transformation, the 3D RAGE LT PRO dramatically improves the performance of the entire 3D pi peline.
DVD and Video Support. DVD and video features include
enhanced motion compensation acceleration and a 4-tap horizontal and 2-tap vertical high quality DVD video scaler, providing smooth images without the jagged edges common to today’s video products. The scaler provides true color video display, independent of the graphics mode used.
AGP 2X mode. With AGP 2X (133MHz) mode support, the
3D RAGE LT PRO offers a peak bandwidth in excess of 500MB/s, which is twice the output of the AGP 1X (66MHz) mode. It also supports AGP’s pipeline and sideband protocols that significantly improved the sustained bandwidth that is critical to the enhanced 3D and video performance.
LI7WM User’s Manual 63
Chapter 8 VGA Driver Installation Guide
8.2 Windows 95/98 Driver Installation
1. After you have installed Windows 95/98, install the Intel 82810
VGA driver. Insert the driver disk provided with the motherboard. Once it is inserted, the following screen appears.
2. Click Intel M/B Drivers and the following screen appears.
64 LI7WM User’s Manual
Chapter 8 VGA Driver Installation Guide
3. Click Intel 82810 Drivers, then Intel 82810 VGA Driver. When the Welcome screen appears, click Next.
LI7WM User’s Manual 65
Chapter 8 VGA Driver Installation Guide
8.3 Windows NT 4.0 Driver Installation
1. After you have installed Windows NT, install the Intel 82810 VGA driver. Insert the driver disk provided with the motherboard. Once it is inserted, the following screen appears.
5. Click Intel M/B Drivers and the following screen appears.
66 LI7WM User’s Manual
Chapter 8 VGA Driver Installation Guide
6. Click Intel 82810 Drivers, then Intel 82810 VGA Driver. When the Welcome screen appears, click Next.
7. Click Next when the Welcome screen appears. Click Yes when the Software License Agreement screen appears. When the Choose Destination Location window appears, click Next to start copying of files. After the files are copies, restart your computer for changes to take effect.
LI7WM User’s Manual 67
Chapter 9 LAN Driver Installation Guide
Chapter 9 LAN Driver Installation Guide
This chapter gives a brief introduction to the Intel 82559B Fast Ethernet PCI controller.
The following items are covered in this chapter:
9.1 Introduction.....................................................................................69
9.2 Features ............................................................................................69
9.3 LAN Driver Installation for Windows 95/98.............................70
9.4 LAN Driver Installation for Windows NT 4.0 ..........................82
9.5 Running Diagnostics......................................................................83
68 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
9.1 Introduction
Intel 82559B is a 32-bit 10/100MBps Ethernet controller for PCI local bus-compliant PCs. It supports the bus mastering architecture, and Auto-negotiation feature which make it possible to combine one common type of Ethernet cabling – an RJ -45 connector for twisted-pair cabling that can be used for both 10Mbps and 100Mbps connection. Extensive driver support for commonly used network operating systems is also provided.
9.2 Features
l Conforms to the Ethernet IEEE 802.3u standard l Compatible with PCI Local Bus Revision 2.1 specification l IEEE 802.3u Auto -Negotiation for automatic speed selection l Supports Full-Duplex/Half-Duplex Operation l Provides 32-bit bus mastering data transfer l Supports 10Mbps and 100Mbps operation in a single port l Supports remote wake-up (Magic Packet*) in APM and ACPI
mode
* Requires ATX power supply with 5VSB, 720mA
LI7WM User’s Manual 69
Chapter 9 LAN Driver Installation Guide
9.3 LAN Driver Installation for Windows 95/98
The LI7WM comes with a diskette labeled Intel 82559B LAN Windows 95/98 & Windows NT 4.0 Drivers that is to be used in conjunction with the LAN drivers installation. You must use the correct drivers in order for LAN to function properly. Follow the steps below
to install the drivers for Windows 95.
1. Click Start ⇒ Select Settings ⇒ Select Control Panel.
70 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
2. Click System.
3. Click Device Manager.
LI7WM User’s Manual 71
Chapter 9 LAN Driver Installation Guide
4. Expand Other Devices.
5. Select PCI Ethernet Controller, then click Properties.
[
72 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
6. Click Driver.
[
LI7WM User’s Manual 73
Chapter 9 LAN Driver Installation Guide
7. Click Update Driver.
74 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
8. Insert the diskette labeled Intel 82559B LAN
Windows 95 & 98 & Windows NT 4.0 Drivers into the floppy disk drive, then click Next.
9. You have to select the Other Location in order to
continue the process.
LI7WM User’s Manual 75
Chapter 9 LAN Driver Installation Guide
10. After select the Other Location, You need to look for your
windows 95 CD ROM location and then type click OK. For example: d:\.
11. If you do not know how to type it, you can click browse
and select LAN from your CD-ROM items.
76 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
12. Choose Intel, and click OK.
13. Type correct the name of the folder and then, click OK.
LI7WM User’s Manual 77
Chapter 9 LAN Driver Installation Guide
14. Click Other Location, You can find out the correct location; but if you select Finish, you will see the performance below.
15. This performance present what you click FINISH from
your computer.
78 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
16. Click OK.
17. Click Finish.
18. Insert the correct CD-ROM.
LI7WM User’s Manual 79
Chapter 9 LAN Driver Installation Guide
19. Click Browse.
20. Insert the WINDOWS 95 CD-ROM, click OK after you
click setup twice.
21. Finally, Click Yes to restart the computer and for the
settings to take effect.
80 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
9.5 LAN Driver Installation for Windows NT 4.0
LI7WM comes with a diskette labeled Intel 82559B LAN Windows 95/98 & Windows NT 4.0 Drivers that is to be used in conjunction of the LAN drivers installation. Follow the steps below to install the drivers for Windows NT 4.0.
1. Click Start Settings Control Panel.
2. Click Network.
3. Click Yes.
4. Select Wired to the network , then click Next.
5. Click from the list.
6. Click Have Disk.
7. Insert the diskette labeled Intel 82559B LAN Windows 95/98 & Windows NT 4.0 Drivers into the floppy disk drive then click OK.
8. Click OK.
9. Click Next.
10. Select the Protocol that you want then click Next.
11. Select Network Services then click Next.
12. Click Next.
13. Insert the Windows NT 4.0 CD into the CD-ROM drive. For
example: type d:\ then click Continue.
14. Click NO
15. Type your IP Address.
16. Click Next.
17. Click Next.
18. Type your Workgroup then click Next.
19. Click Finish.
20. Click Yes to restart the computer and for the settings to take
effect.
LI7WM User’s Manual 81
Chapter 9 LAN Driver Installation Guide
9.6 Running Diagnostics
The LI7WM comes with a diskette containing a diagnostic software
supporting the Intel 82558B Ethernet controller. Follow the steps below to use the Setup Utility.
1. Run the file SETUP.EXE typing a:\setup in the DOS prompt,
assuming your floppy disk drive is drive A. Upon doing so, the system starts the Setup Utility and shows the following screen.
Choose AUTOMATIC SETUP to view the adapters configuration, make sure it works properly, and install the software needed to connect to your network.
Help = F1 Exit = Esc Select = ↑↓ Action =
2. Selecting View adapter configuration will show the following.
Help = F1 Previous = Esc Continue = Enter PCI Advanced = F5
8255x-based PCI EtherExpress™ adapter Setup V4.21
Main Menu
Automatic setup
View adapter configuration Test adapter Install network drivers View Help files Exit Setup
8255x-based PCI EtherExpress™ adapter Setup V4.21
View adapter configuration
Adapter type:………………….. Adapter part number:…………. Network address:……………… Interrupt:……………………….. Bus:……………………………. Slot:…………………………….. Device:………………………… Network speed:……………….. Physical layer device:………… Duplex:………………………… Adapter capabilities: 100BaseTX, full or half duplex. 10BaseT, full or half duplex.
Press Enter to continue
82 LI7WM User’s Manual
Chapter 9 LAN Driver Installation Guide
Main Menu
3. Selecting Test adapter will show the following screen.
8255x-based PCI EtherExpress™ adapter Setup V4.21
Test adapter
Bus=0 Dev=0Bh Slot=11 Addr=004063001000
IRQ=10
Diagnostic tests:
Adapter tests ……………………………. Passed Onboard loopback tests ……………….. passed Network test …………………………… passed 10Mbps
This adapter works properly
Press Enter to continue
Help = F1 Press Enter to continue
4. Selecting Install network drivers will show the following screen.
8255x-based PCI EtherExpress™ adapter Setup V4.21
Install network drivers
Novel Microsoft Other
Exit Setup
Choose OTHER if you use a network operating system from a manufacturer not on this list (such as Banyan or UNIX).
Help = F1 Press Enter to continue
LI7WM User’s Manual 83
Chapter 9 LAN Driver Installation Guide
Main Menu
5. Upon selecting Others under the Install network drivers main menu screen, the following screen will appear.
8255x-based PCI EtherExpress™ adapter Setup V4.21
Other
1. LANtastic 6.0
2. Banyan 6.00 NDIS workstation
3. NDIS 2.x driver notes (OS/2*, LAN Manager* others)
4. Using IBM LAN support for AS/400 and NetWare
5. LAN Server
6. UNIX driver information
Choose OTHER if you use a network operating system from a manufacturer not on this list (such as Banyan or UNIX).
Help = F1 Previous = Esc Select = ↑↓ Accept =
6. Selecting View Help files under the Main menu will show the following screen.
Help = F1 Previous = Esc Select = ↑↓ Display Choices =
8255x-based PCI EtherExpress™ adapter Setup V4.21
View Help files
Installing EtherExpress™ PRO/100+ adapter drivers Latest News and general adapter information Hardware specifications and cabling information Adapter installation and special configurations Running diagnostics and error messages
84 LI7WM User’s Manual
Chapter 10 System Monitor Utility User’s Guide
Chapter 10 System Monitor Utility User’s Guide
This chapter introduces System Monitor Utility that comes with the motherboard in conjunction with the onboard hardware monitoring IC. The sections below give the functions of the utility.
System Monitor is a software utility that oversees the general performance of systems, covering areas like system temperature, system voltage, CPU and system fan rotational speeds. If conditions become adverse, that is, when voltages are erratic or CPU temperature exceeds the safe limits, an alarm will be sounded; thereby preventing system crashing and ensuring overall stability.
NOTE: System Monitor currently supports English and Chinese
under Windows 95/98 and Windows NT. English will be used for other language environments.
When System Monitor is initiated, the icon below appears in the task bar in the Windows environment.
LI7WM User’s Manual 67
Chapter 10 System Monitor Utility User’s Guide
The following screen appears upon clicking on the System Monitor icon.
Clicking on the upper left corner button would show you the latest company information. "Summary" provides the current system status.
The section below describes the different functions of System Monitor.
1. Computer - displays the current working system version and
processor type.
86 LI7WM User’s Manual
2. Power - displays the current voltage status.
LI7WM User’s Manual 87
Chapter 10 System Monitor Utility User’s Guide
3. Memory - displays the c urrent memory usage status.
88 LI7WM User’s Manual
4. Fan Speed - displays the current rotational speeds of CPU and Chassis fans.
5. Disk - displays the supported disk formats and disk
space.
LI7WM User’s Manual 89
Chapter 10 System Monitor Utility User’s Guide
6. Heat - displays the CPU and system temperatures.
7. Error Log - displays errors occurring after System Monitor is started.
90 LI7WM User’s Manual
8. Setting - sets the values at which an alarm is sounded.
Voltage : the acceptable voltage range between the "MAX"
Temperature : temperature threshold. Fan Rotation Speed : the minimum rotation speed.
NOTE: Intel has defined a margin of difference for the voltages as
below: 12 Volts - 10% (10.8V ~ 13.2V) 5 Volts - 5% (4.75 ~ 5.25%) Vio - 5% (Vio for P54C CPU is 3.5V. Vio for P55C is 3.3V.) Vcore- 5%
WARNING: Micro ATX power supplies do not support -5V voltage.
DISABLE the alarm of this item after you have installed the System Monitor utility to prevent the system from sending a ’false’ alarm.
LI7WM User’s Manual 91
Chapter 10 System Monitor Utility User’s Guide
This page was intentionally left blank.
92 LI7WM User’s Manual
Chapter 11 LI7WM and the Databook Case
FRONT
1-1 Remove screw
1-2 Slightly pull 1-2
1-3
Back Panel
1-4
Pull up to
Front
This chapter provides a step -by-step guide describing the procedure of installing the LI7WM motherboard into its databook case. Carefully read the instructions and follow the procedures one step at a time.
1. Removing top cover.
1-1. Remove the m iddle upper screw at the back of the case. 1-2. Slightly pull out the two clips on the two sides of the top cover. Make sure the clips are now ‘unlocked’ before proceeding to the next step. 1-3. Pull the top cover towards the back of the case by 2cm. 1-4. Remove the top cover in an upward direction.
Panel Edge
Pull 2cm
remove
clip on both
LI7WM User’s Manual 67
Chapter 11 LI7WM and the Databook Case
Back Panel
Remove the
2-1
2-2
Pull out the whole 2-1
Back Panel
3-1 screw to remove
3-2 Remove
3-3 Install the thin
2. Removing the front panel section. 2-1. Remove the two flat-head screws on the two front corners of the case. 2-2. Pull out the whole front panel section. The front panel section has room for an FDD, HDD and CD-ROM drive.
front panel unit.
flat-headed screw on
both sides
3. Installing the main components 3-1. Remove the riser card support by removing the screw from the back panel. 3-2. Remove unnecessary I/O cover plates from the back panel. Check the external I/O connectors on the motherboard to determ ine which plates should be removed.
Remove the the riser card
support
94 LI7WM User’s Manual
I/O panel plate inside the
unnecessary
Back Panel
3-9 Screw 3-7 Install the
3-8 Remove this
3-3. Install the thin I/O panel plate inside the case. Be careful not to cut yourself in doing so. The thin metal plate has six protruding clips that should be inserted to their respective hole on the back panel. 3-4. Install the CPU retention module to the LI7W M motherboard. 3-5. Install the motherboard into the case. 3-6. Install the game port cable onto the motherboard (J17 header) and screw the connector onto the case. 3-7. Install the power supply onto the case . 3-8. Remove the power supply top screw diagonally opposite the corner of the case. This screw will be used to fix the riser card metal support. 3-9. Insert the BL21PI Riser Card onto the motherboard. Screw the card onto the riser card metal support. 3-10. Screw the metal support to the power supply. Use the screw that was remove from the power supply as mentioned in 3-8.
the riser card to the
screw. 3-10 Screw here to attach the riser
power supply into
3-11. Screw the FDD plastic siding onto the left side of the floppy disk drive. Refer to the figure on the next page. Note that the FDD plastic siding has six holes on it while the HDD plastic siding has two holes. Make sure to use the small-thread ‘mm’ screws for
the FDD and CD-ROM drives and use the big-thread ‘inch’ screws for HDD drive to avoid damage to the drives.
3-12. Install the floppy disk drive into the front panel unit.
LI7WM User’s Manual 95
Chapter 11 LI7WM and the Databook Case
3-11 Attach the FDD front side
3-11 Attach the
HDD front side
Back Panel
4-2. Remove this
ew and
the
4-2. Remove either one expansion
plastic siding
plastic siding
3-13. Screw the HDD plastic siding onto the right side of the hard disk drive. 3-14. Install the hard disk drive and CD -ROM into the front panel unit. 3-15. Install the CPU. 3-16. Install the front panel unit back to the case. 3-17. Connect the cables for FDD, HDD, CD-ROM, and mini cables for HDD LED, power LED, LAN LED and reset switch. 3-18. Screw the front panel section back to the case. Refer to 2-1. 3-19. Return the top cover with a gap of 1cm (Do not exceed 1cm.) between it and the front panel edge. Refer to 1-3. 3-20. Press down the top cover and push it to the front until the two clips on the sides of the cover lock in place. Refer to 1-2. 3-22. Stick the four base supports supplied to the designated points at the bottom side of the case.
4. Installing an additional PCI expansion card. 4-1. Remove the top cover. Refer to sections 1-1 ~ 1-4. 4-2. Remove the left-side screw at the back of the case and the small plate. And then remove either one of the expansion slot cover. 4-3. Install the PCI expansion card. 4-4. Return the left-side plate and its screw. 4-5. Screw the PCI card into place
96 LI7WM User’s Manual
scr
of the
Loading...