Timeguard TPSL04 User Manual

TPSL01, TPSL02, TPSL03, TPSL04
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
TPS101, TPS201, TP203
InstructIons
1 Product Range Covered
TPS101
Single Socket Outlet Unit
Special IP55 weatherproof seal
Easy lift spring back lid cover
IP55 weatherproof rating
5 x 20mm knockout cable entries
Tough, durable impact resistant housing
Suitable for all BS 13 amp plugs
TPSL01
Single Switch
TPSL03
Single Bell
Push Switch
TPSL04
20AX DP Switch
Rocker Rockers
IP55
weatherproof
rating
Complies with
EN60669
5 x 20mm
cable entries
Tough, durable
impact resistant
housing
Bottom cable entry with
cut to size grommet
Single Gang
Back Box
(TPS101, TPSL01, TPSL02, TPSL03,
TPSL04)
2 x Earth terminals
2 x drain hole cut
outs (if required)
TPSL02
Double Switch
(single gang size)
5 x 20mm
conduit
knockouts
2 x 8 fixing
holes
Cut to size
blind grommet
TPS201
Special IP55
weatherproof
seal
Double Socket Outlet Double Gang Unit
Easy lift spring back lid covers
IP55 weatherproof
rating
8 x 20mm knockout
cable entries
Tough, durable
impact resistant
housing
Suitable for
all BS 13 amp
plugs
TP203
20A Switch and 13A Socket Outlet Double Gang Unit
Special IP55
weatherproof seal
Easy lift spring
back lid cover
8 x 20mm knockout
cable entries
IP55 weatherproof
rating
Rocker
Suitable for
all BS 13 amp
plugs
Tough, durable
impact resistant
housing
Double Gang Back Box
4 fixing holes
2 x Earth
terminals
(TPS201, TP203)
8 x 20mm conduit
knockouts
4 x drain hole cut outs (if required)
Switch rocker should be
removed by prising off with
a flat screwdriver. Use a
piece of card to prevent
marking the the unit.
Cut to size
blind grommets
2 Installation
This product must be installed in accordance with the appropriate Building and Wiring Regulations.
In all cases if there is a doubt as to how to proceed with an installation consult a qualified electrician, your Local Authority’s Building Control Department or the Timeguard Helpline (020 8450 0515).
For the switches the screws holding the case halves together are located beneath the rocker(s) (front plate switch actuator(s)).
To remove the rocker first press rocker inwards at the blind grommet end, then, removing hand from there, force fingers as far as possible between the opposite end of the rocker and the case, pulling the rocker outwards. The rocker will unclick at it’s pivot point.
If it is not possible to exert enough force by hand, use the technique shown at the foot of the previous page.
2.1 Cable Entry
Try to avoid siting the units in areas where there is direct sunlight for any length of time.
Cable entry can be made via conduit into any of the 5 (8 for the double socket TPS201 and switch socket TP203) knock outs on the top, bottom, sides or back of the back box. In all cases ensure there is a drain hole at the lowest point in the attached conduit system.
The knock out outline should be heavily scored with a sharp knife before tapping out. The appropriate sealing washers for the conduit in use must be used to maintain the IP rating. The use of any knock outs apart from the one(s) at the bottom requires that the lower drain hole(s) on the back box is opened and the IP rating may well be reduced. The blind grommets may be used for cable entry at the bottom 20mm hole(s). They must not be used in any other position (including the rear) or the IP rating may be severely prejudiced. The blind grommets should be pierced centrally to give an undersize hole of a similar shape to the cable cross section.
2.2 Fixing Back Box
Drill 2 holes (4 for the double socket TPS201 and switch and socket TP203) according to the dimensions given on the rear of the back box. Fix with round head no. 8 woodscrews or equivalent using wall plugs if necessary. The length of the screw will depend on the surface being fixed to, for example fixing to roughcast would require a longer screw than fixing to brickwork.
2.3 Connecting Cables
Allow sufficient excess cable to wire up the socket(s) or switches but not too much to make it difficult to close the front plate onto the back box.
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
2.3.1 Sockets
In spur configuration we recommend feed cable of 1.5 sq. mm for the single socket and 2.5 sq. mm for the double socket. If the unit is to form part of a ring then incoming and outgoing cables must both be 2.5 sq. mm (with the double socket we recommend that the incoming and outgoing cables can be connected to one socket each with a 2.5 sq. mm bridging cable between the two sockets. Use back box earthing terminals to maintain earth continuity where required. With the TP203 switch and socket the double pole switch may be used independently from the socket for switching e.g. lighting, or it may be used to switch the live or live and neutral supply to the socket outlet.
2.3.2 Switches
These switches are not suitable for intermediate use in three way (and above) systems. Wiring to the switches would normally be in 1 sq. mm or 1.5 sq. mm for heavier loads. Use back box earthing terminals to maintain earth continuity where required.
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
2.3.2.1 Single Switch (TPSL01) - On/Off
L
(supply live)
L
A2
2.3.2.2 Single Switch (TPSL01) - 2 Way (Strapping Cable)
A1
A2
TPSL01
L
COM
Standard Switch (remote)
(could also be a second TPSL01
2.3.2.3 Single Switch (TPSL01) - 2 Way (Remote Live Access)
L (supply
live)
Connections to SL (lights) and L (supply live) can be swapped if required.
L
A1
A2
TPSL01
SL
(to light(s))
L
(supply live)
L1
L2
SL (to light(s))
or half a TPSL02)
L1
L2
Standard Switch
(could also be a second TPSL01 or half a TPSL02)
COM
SL
(to light(s))
(remote)
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
2.3.2.4 Bell Switch (TPSL03) - On/Off Only
Any a.c. voltage supply up to 230V.
L
A1
2.3.2.5 Double Switch (TPSL02) - Both On/Off
C
A2
L
B2
L
(supply live)
L
(supply live)
to bell(s)
SL
(to light(s))
SL
(to light(s))
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
2.3.2.6 Double Switch (TPSL02) - Both 2 Way (Strapping Cable)
A1
A2
TPSL02
C
COM
Standard Switch (remote)
L1
L2
L
(supply live)
SL (to light(s))
B1
B2
TPSL02
Either standard switch could be a TPSL01 or half a TPSL02.
L
COM
Standard Switch (remote)
L1
L2
L
(supply live)
SL (to light(s))
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
2.3.2.7 Double Switch (TPSL02) - Both 2 Way (Remote Live Access)
L (supply
live)
L (supply live)
Either standard switch could be a TPSL01 or half a TPSL02).
Connections to SL (lights) and L (supply live) can be swapped if required.
A1
C
A2
TPSL02
B1
C
B2
TPSL02
L1
COM
L2
Standard Switch
L1
COM
L2
Standard Switch
2.3.2.8 TPSL04
This has two ON/OFF isolated switches controlled by a single rocker which can be wired to switch both live and neutral for a single circuit or can be wired to switch live only for two circuits (where the total load exceeds 20A) or can provide totally independent control of two circuits (albeit simultaneously).
SL
(to light(s))
(remote)
SL
(to light(s))
(remote)
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
3 Specifications
3.1 Sockets
Current rating: (single TPS101, TP203) 13A to BS1363 (double TPS201) 20A to BS1363 Voltage: 230V, 50Hz a.c. Weatherproof rating: IP55 Operating temperature range: -10 to 40ºC Installation temperature range: 0 to 30ºC Complies with: BS1363 Conforms to directives: 73-23-EEC, 89-336-EEC
3.2 Switches
Current rating: (TPSL01, TPSL02, TPSL03) 10AX (10A fluorescent rated) (TPSL04, TP203) 20AX (20A fluorescent rated) Voltage: (TPSL01, TPSL02, TPSL04) 230V, 50Hz a.c. (TPSL03) Any voltage up to 230V, 50Hz a.c. Weatherproof rating: IP55 Operating temperature range: -10 to 40ºC Installation temperature range: 0 to 30ºC Conforms to directives: 73-23-EEC, 89-336-EEC
3 Year Guarantee
THREE YEAR
GUARANTEE
3
FIVE YEAR
GUARANTEE
5
In the unlikely event of this product becoming
faulty due to defective material or manufacture
within 3 years of the date of purchase, please
return it to your supplier in the first year with proof
For years 2 and 3 or any difficulty in the first year
telephone the helpline on
For a product brochure please contact:
Timeguard Ltd. Victory Park, 400 Edgware Road,
London NW2 6ND Tel: 020-8452-1112
or email csc@timeguard.com
A Group company
67-058-152
020 8450 0515.
Loading...