Timeguard LEDPRORFKB, LEDPRORFKWH, LEDPROFOB RF, SLB2300RF, LEDPROFOB Installation & Operating Instructions Manual

Installation & Operating Instructions

Dedicated PIR Light

Controller c/w RF remote

control for LEDPRO

Floodlights

Model: LEDPRORFKB – Black

Model: LEDPRORFKWH – White

Model: LEDPROFOB RF Remote Fob

1

1. General Information

These instructions should be read carefully
and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the
mains supply to the PIR sensor is switched off
and the circuit supply fuses are removed or
the circuit breaker turned off.

• It is recommended that a qualified electrician is
consulted or used for the installation of this PIR
sensor and install in accordance with the current
IEE wiring and Building Regulations.

• Check that the total load on the circuit including
when this PIR sensor is fitted does not exceed the
rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

PIR Light Controller

• Operating Voltage: 230V AC 50Hz

• This product is of Class I Construction and must
be earthed.

• Detection Angle: 180°

2

• Motion Detection Range:
Up to 12m distance at a 2.5m mounting height

• Maximum Switchable Load;
140W LED Lighting
1000W Halogen Lighting
200W CFL Lighting
500W Fluorescent tube w/o PF correction

• Time ON Adjustment: 3 seconds – 18 minutes

• Warm Up Period: Approximately 35 seconds

• Dusk (LUX) Level Adjustment: 2 – 1000 Lux

• Operating Temperature: -20°C to +40°C

• Standby (W): <0.5W

• Manual Override Mode:
ON/OFF operation using RF Remote Fob (6 fobs max)

• Sensor Head Adjustment:
Pan angle = Left/right 90°, Tilt angle = Down 150°

• RF Module: RX Receiver

• RF Frequency: 433.92MHz

• IP55 Rated suitable for restricted external applications

• CE Compliant

• Dimensions (H x W x D): 114 x 78 x 127mm

RF Remote Fob

• Battery: 3V (1x CR2032)

• Battery Life:
Approximately 24 months (@ 10x opt/day)

• Class Rating: Class III

3

• Transmission and Receiving Distance:
100m hand held (clear line of sight)
10m when mounted inside a wall switch
(recommended mounting height = 1.2m)

• Total number of fobs usable per PIR: 6

• Operating Temperature: -20°C to +40°C

• RF Module: TX Transmitter

• RF Frequency: 433.72MHz to 434.12MHz

• IP44 Rated suitable for restricted external
applications

• CE Compliant

• Dimensions (H x W x D): 60 x 38 x 15mm

4. Pack contents

• 1x LEDPRORFKB-WH Dedicated PIR Light Controller
c/w RF remote control for LEDPRO Floodlights

• 1x LEDPROFOB RF Remote Fob

• 1x Instruction Manual

• 1x 3V CR2032 Battery

• 1x Lens Sticker

• 2x Wire (for wall mounting a fob)

5. Selecting a Location

• The light controller has number of detection zones,
at various vertical and horizontal angles as shown
(see diagram A).

4

• A moving human body needs to cross/enter one
of these zones to activate the light controller.
The best all-round coverage is achieved with the
unit mounted at the optimum height of 2.5 metres.

• Careful positioning of the light controller will be
required to ensure optimum performance (see
diagram A detailing detection range and direction).

• The light controller is more sensitive to movement
ACROSS its field of vision than to movement
directly TOWARDS (see diagram B). Therefore
position the unit so that the light controller looks
ACROSS the likely approach path.

• Avoid positioning the light controller where
there are any sources of heat in the detection
area (extractor fans, tumble dryer exhausts etc.)
including opposite any other light sources such
as other security lights.

• Reflective surfaces (i.e. pools of water or white
painted walls) and overhanging branches may
cause false activation under extreme conditions.

5

6. Installation

6.1 Ensure the mains supply is

switched off and the circuit
supply fuses are removed or
the circuit breaker turned off.

6.2 An isolating switch should be installed

to enable the power to be switched ON & OFF
for maintenance purposes.

• During extreme weather conditions the motion
light controller may exhibit unusual behaviour.
This does not indicate a fault with the light
controller. Once normal weather conditions return,
the light controller will resume normal operation.