Thule Audio RC-250 Owners manual

If you have a different brand of TV or
other types of equipment i.e. satellite
receiver, VCR and need to change the
settings, first activate the desired device
you want to change in the device menu
and hold down the ‘mode’ button (silver
button on the far left underneath the
touch-screen) for three seconds. (arrow

4)

The following is an example for
changing the brand in TV mode. This
applies for all types of products.
Choose ‘brand’, follow the instructions
on the screen, and enter one of the
four-digit codes for your TV-brand,
which you find in the booklet enclosed
(arrow 6). Press ‘OK’ when finished or
‘cancel’ if you made a mistake (two
middle silver buttons, arrow 5). Then
press ‘use’ on the screen, and check if
the code works. If it doesn’t, or only
some functions work, try with one of
the other codes for your brand. In some
cases, you must use the learn function
to ensure all commands for a device
works.

In the programming mode, you can also
make several other changes, i.e.
program macros (macro), change the
name for any button (label) or use the
learning function (learn).

Thule Audio reserves the right to alter design and
specifications without notice

Picture 3

Picture 3

Picture 3Picture 3

System Remote Control

4444

5555

RC250

How to get started

6666

Picture 4

Picture 4

Picture 4Picture 4

First of all, congratulations with your
new Thule Audio RC250 system remote
control. The RC250 can replace all your
existing remote units, and it is pre­programmed to control all types of
Thule Audio products.

IMPORTANT:

IMPORTANT: If you wish to make sure

IMPORTANT:IMPORTANT:
that you can always recall the factory
programming, you should install the
NEO Edit 4 program on your computer,
from the enclosed CD-ROM, and upload
the configuration from your RC250,
using the COM cable from the box.
Please see the original manual from the
manufacturer for further details.

You can also learn more about the many
other advanced functions in your
remote from the Neo Edit 4 manual.

It is a good idea to save your existing
configuration on a computer before you
make any changes in the remote. This
way, you can
always reload the original file if
something goes wrong.

In the NEO Edit program, you can also
change all settings and programming in
the remote, and you can insert
downloads into your remote from
various international internet sites, such
as:

remotecentral.com

On this site, you can download
hundreds of different set-ups for many
types and brands of products.

General advise on using the RC250

General advise on using the RC250

General advise on using the RC250General advise on using the RC250
The pre-programming on this remote is
meant for controlling a full Thule Audio
system. For example, when you are in
‘Device mode’, you can put both your
Thule PR2/350B in standby as well as
your Thule DVD player. In ‘Device’
mode, the ‘Volume’ controls the PR, and
the channels are set to control your TV.

Device pre

Device pre----programming:

Device preDevice pre

programming:

programming:programming:
TV: Sony, codeset 0037
VCR: Philips, codeset 9027
Tuner: Thule Audio, codeset 9027
CD: Thule Audio, codeset 9027
Sat: Philips, codeset 9027
Amp: Thule Audio, codeset 9027
DVD; Thule Audio, codeset 9027
Tape: Philips, codeset 9027
Processor: Thule Audio, codeset 9027
CDR: Philips, codeset 9027
Cable: Jerrold, codeset 0030

This box contains:

This box contains:

This box contains:This box contains:
1 Thule R

1 Thule RC250 System remote

1 Thule R1 Thule R
1 Thule manual ‘How to get started’

1 Thule manual ‘How to get started’

1 Thule manual ‘How to get started’1 Thule manual ‘How to get started’
1 Com cable for PC uploads

1 Com cable for PC uploads

1 Com cable for PC uploads1 Com cable for PC uploads
1 CD

1 CD----ROM, Neo Edit 4

1 CD1 CD
1 Philips manual for Neo Edit 4

1 Philips manual for Neo Edit 4

1 Philips manual for Neo Edit 41 Philips manual for Neo Edit 4
3 AA batteries

3 AA batteries

3 AA batteries3 AA batteries

C250 System remote

C250 System remoteC250 System remote

ROM, Neo Edit 4

ROM, Neo Edit 4ROM, Neo Edit 4

SSSShortcut version for immediate use:

hortcut version for immediate use:

hortcut version for immediate use:hortcut version for immediate use:

Insert batteries on the rear side.

(Picture 1) After a one-second start-up
period, the remote will always open in
device mode. To get back to this mode,
press far right silver button underneath
touch-screen (arrow 1).

On the touch-screen, now choose the
device you wish to operate:

- ‘processor’ (if you have a
PR250B/350B or AV100/120),

- ‘amp’ (for any other Thule amplifier)

- CD-player, tuner etc.

If you need light to see the touch­screen, press the small top button on
the left side of the RC250 just under the
connector cable hole. (arrow 2)

arrow 3

arrow 3

arrow 3arrow 3

After you have chosen the device, the
various function choices will appear,
like ‘stand-by’, ‘play’, ‘stop’.

(Picture 2) For some complex units like
processors, videos, TVs and DVDs,
there are several screen pages with
functions. These can be scrolled by the
two larger buttons on the left side of
the RC250. You can also scroll to the
second page in the device page (arrow

3).

3333

2222

Picture

Picture 1111

Picture Picture

1111

Picture 4

Picture 4 Picture 2

Picture 2

Picture 4Picture 4

Picture 2Picture 2