Thrane and Thrane A S 6300B Installation guide
Disclaimer
SAILOR 6300 MF/HF Transceiver Unit
& Antenna Tuning Unit 150/250/500W
Installation guide
How to install the Transceiver Unit 150/250W
391 mm
360 mm
4 x ø8mm
145 mm
88 mm
Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying
documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information purposes
only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane
are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g.
from cobham.com/satcom or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of
any translations or reproductions, in whole or in part, of this manual from any other source.
Thrane & Thrane A/S trading as Cobham SATCOM.
How to install the Antenna Tuning Unit 150/250W
80 mm
290 mm
200 mm
80 mm
50Min. mm
Space to nearest overhang
Space for airflow
and service
150 mmMin.
Space for
service
4 x ø6mm
150 mmMin.
Space for
cable access
443 mm
Cable fitting
360 mm
379 mm
105 mm 350 mm
23.5 mm
35 mm
How to connect the antenna
In general a 12 metres antenna installation is preferred and can be made using an 8
metres whip and 4.5 metres feeder or a 10 metres whip and 2.5 metres feeder. In both
cases the whip should be mounted on a pole providing sufcient height to have the
Antenna Tuning Unit mounted such that it allows for the feeder to be erected at an
angle of 45 to 60 degrees, creating a combined 12 metres vertical antenna system.
500Min. mm
500Min. mm
Space for
service access
75 mm
271 mm
150Min. mm
Space for cable and
service access
164 mm 164 mm
12 mm
504 mm
352 mm
How to install the Antenna Tuning Unit mounting bracket
Optional accessories:
Mounting plate and ttings for mast part no 737589.
Mounting plate only - part no 737588.
1
3 5
2
4
The feeder wire is terminated at the antenna horn at the top of the Antenna Tuning
Unit. Use a supporting insulator near the ATU to carry mechanical stress from the
feeder wire. Use a short exible part of the feeder wire between the supporting
insulator and the ATU horn in order not to apply mechanical stress to the antenna horn.
To maximize the radiated power and avoid ash
over, keep distance to metal parts as long as
possible, preferable more than 100 mm. Use a
short direct ground connection from the ground
clamp at the bottom end at the Antenna Tuning
Unit to nearest suitable metal ground plane.
It is recommended to use the ATU mounting
bracket for the physical tting of the ATU.
For further information, download the installation
manual 98-144591 at www.cobham/satcom.
5
3
Optional accessories:
Antenna connection kit
part no 405301A-905.
3
4
1
1
2
200 mm
1. Nut M10
2. Tooth lock washer M10
3. Fitting for mast
4. Mountingplate for ATU
5. Treadrod M10
1
2
1. Shackle
2. Isolator
3. Wire clamp
4. Wire
5. Cable tie
6. Wire lug
6
Wire length 4 metres
1000 mm
1. Pan head screw M6x16 mm
2. Washer M6
3. Hexagon head screw M6x10 mm
4. Flat washer ø6.4xø12x1.6 mm
3
4
How to install the Transceiver Unit 500W
391 mm
360 mm
332 mm
4 x ø8mm
505 mm
217 mm
How to install the Antenna Tuning Unit 500W
160 mm
1000Min. mm
Space for airflow
and service
200 mmMin.
Space for
service access
Cable fitting
4 x ø6mm
150 mmMin.
Space for cable
and airflow
360 mm
379 mm
System conguration - Example
35 mm 105 mm 350 mm
23.5 mm
1. Distance to metal constructions: min. 150
2. Space for service access: min. 500
3. Space for cable and service access: min. 200
Dimensions are in mm
Rx
Tx
TT-6201A
Handset
Distress Alarm
2182 select option
GPS on LAN option
(Optional)
TT-6270A
Other Alarm
GPS option
TT-6209A
Accessory
Connection Box
TT-6209A
Accessory
Connection Box
TT-6201A
Handset
TT-630xA
MF/HF Control Unit
(Optional)
TT-6208A
Control Unit
Connection Box
TT- 6103A
Alarm Panel
250W MF/HF with 6 ch. Scanning
DSC Watch receiver
TT-636xB
Transceiver Unit
TT-6197A
Ethernet Switch
Antenna Tuning
TT- 6006A
Message Terminal
TT-6001A
Keyboard
TT-638xB
Unit
Telex option
H1252B
Printer
TT-608xA
Power Supply
98-144542-A.01
www.cobham.com/satcom
Optional connection
For further information, download the installation
manual 98-144591 at www.cobham/satcom
Loading...