HRH
Range Hood Installation Guide and User Manual
Applicable model: HRH3001U HRH3002U HRH3003U HRH3004U HRH3005U
HRH3601U HRH3602U HRH3603U HRH3604U HRH3605U
HRH4801U HRH4802U HRH4805U
Safety Notice
Approved for residential type untis for residential use only read these insructions and be safe.
Please read these instructions completely before starting.
The installation of the appliance must respect all codes.
Important: Save these instructions so that you can provide the electrical inspector in your area.
Safety Warning: Turn off the circuit in the electrical panel and lock front panel to connect the cord of this unit.
Power requirement: 110V-120V/60HZ
CAUTION: USE THIS PRODUCT FOR GENERAL FAN ONLY. DO NOT USE THIS PRODUCT TO EXHAUST FUMES OR
HAZARDOUS OR EXPLOSIVE MATERIALS.
WARNING TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PEOPLE, OBSERVE THE
FOLLOWING:
1. Use this unit only for the purposes intended by the manufacturer. If you have any questions about this product, contact the
manufacturer.
2. Before the machine’s maintenance or cleaning, turn off the electrical panel and lock the panel blocking feature to prevent
from accidentally activating the power. If it is not possible to lock the access panel, attach a highly visible label to the
electrical panel.
3. A qualified person should perform the installation and wiring of the electricity in accordance with all codes and all
standards, including fire resistance rating.
4. When you use hood together with stove, please do not close the window and door of the kitchen. Because during the fuel
stove working, which will consume lots of air, so do open the door and window to make the kitchen ventilating, to avoid
any suffocation.
5. It is important to provide sufficient air for proper combusion of heating equipment and proper evacuation of gases through
the chimney pipe to prevent back flow of air. Follow the instructions and safety standards of the manufacturers of heating
equipment, such as those published by the National Fire Protection Association (NFPA), the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASJRAE) and the code authorities in your area.
6. When cutting or drilling into wall or ceiling, be sure not to damage electrical wiring or other access to public service.
7. Always evacuate outside the conduit system.
To reduce the risk of fire and to properly exhaust air, be sure that the pipe is leading outside, do not exhaust air into the
space between the walls, ceilings, attics, crawl spaces or garages.
Waring: TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT, Install this hood in accordance with all the
requirements mentioned.
WARNING: TO REDUCE THE RISK OF FIRE, GREASE THE RANGE.
1. Never leave the stove unattended when it is at a high temperature. Boil overs cause smoke and fat that overflows can
ignite. Heat the oil slowly at a low or medium temperature.
2. Always operate the hood when you use the stove to high heat or when you Flame.
3. Clean ventilating fans frequently. Do not let fat accumulate on the filters or propellers.
4. Use proper pan size. Always use a pot size appropriate to the stove element.
5. Do not touch on-working or off-soon bulb, to avoid any thorny.
Warning
TO AVOID INJURING SOMEONE IN A GREASE FIRE, FOLLOW THE FOLLOWING:
1. SMOTHER FLAMES with a lid to the dimensions of the cooking hobs, a cookie sheet or other metal tray, then turn off the
gas or power supply of the stove. BE CAREFUL NOT TO BURN YOURSELF. If the flames do not go out immediately, LEAVE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK IP A FLAMMING PAN. You could be hurt.
3. DO NOT USE WATER, including Dish towels or wet towels-a violent steam explosion of dew may be occured.
4. Use an extinguisher only if:
. You are sure to have a Class ABC extinguisher that you know how to use.
. The fire is small and confined to the area where it was formed.
.Firefighters was called.
.You can fight against the fire with an exit behind you.
Operative Mode
Always leave safety grills and filers in place. Without the presence of lowers could catch hair, fingers or clothing. The
manufacturer is not liable if detailed in this manual for installation info, maintenance and proper use of the product are not
observed. The manufacturer declines all responsibility for any injury caused by negligence. This product is manufactured for
internal use. Do not use this appliance outdoors.
Electrical requirements and installation requirements
Power
Requirements
that
the
hood
is
properly
grounded
electrically.
Do
not
install
a
fuse
in
the
neutral
circuit
or
circuit
ground.
1.Toensure
the
most
efficient
ventilation
possible,
install
the
pipe
inastraight
lineorwith
the
least
elbows
possible.
CAUTION:
2.
Two
people
are
required
for
installation.
of
the
cold
air
from
the
heat
insulator.
The
insulation
must
be
placed
as
close
as
possible
to
where
the
pipe
enters
the
heated
5.
Air
booster:
The
building
code
in
your
area
may
require
the
useofa
make-up
air
system
if
you
useaventilation
system
Remove
the
packaging.
CAUTION
:
IMPORTANT
Observe all governing codes and ordinances. The customer is responsible for: Contacting an electrician-installer. Check that
the electrical installation is adequate and in conformance with the National Electrical Code, ANSI / NFPA 70 (latest edition *)
or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 (the latest edition **) of the CSA, and all
codes and ordinances in your area. If codes permit and use a wire to separate the ground, it is recommended to check the
path of the wire by an electrician. Do not put the device to land on a gas line. Consult a qualified person if you are not sure
Location of the electrical installation
• The cable must enter the rear wall at least 20 to 1/4 "above the height of the installation base, and between 7-5/8" and 4-7/8
"from the left side of the middle line.
MPORTANT
Keep these instructions in order to return them to the electrical inspector. The hood must be plugged directly into a 110 volt
wall outlet.
Before installing the hood
The output of the vent pipe should give to the outside.
3. Supplied hardware can secure the hood to most walls and ceilings, consult a qualified installer to ensure that the hardware
provided is suitable for your type of wall or cabinet.
4. In the case of areas prone to COLD WEATHER, install a check against extra-circulation to minimize the cold air return and
a nonmetallic thermal break to minimize conduction of outside temperature in the duct. The valve must be placed on the side
part of the house.
which leads the movement of air exceeding a certain number of CFM. The number of ft3/min varies from one region to
another. Consult your HVAC professional for specific requirements in your area.
Carefully remove the cardboard, gloves to protect against sharp edges.
Examples and positioning possibilities ducts
The
manufacturer
declines
any
liability
with
respect
to
any
loss,
damage
or
fire
caused
by
non-observance
of
the
instructions
Models
Chimney
hood
Wall:
HRH3003U,
HRH3004U
Follow the letter of the guidelines presented in this manual.
contained in this manual.
Ventilation methods
The hood is equipped with a vertical transition to remove fumes outside.
Recommended diameter conduit model and wall chimney hood and hood island: vertical round pipe 7'' tolerance + or – 1.
Do not cut a joist or stud unless it is absolutely necessary to do so. If you need to cut a joist or stud, you must build a support
Framework, hardware supplied can secure the hood to most walls and ceilings. However, you should ask a qualified
technician to check the strength of materials depending on the type of wall or ceiling. Before cutting, make sure there is
enough clearance in the ceiling or wall for the outlet pass. You can determine for yourself how high you install the hood above
the stove. Over the hood near the stove, it is more effective to capture cooking odour, grease and smoke.
Clearance Training
Caution
:
When
install
the
hood,
the
height
should
notbetoo
high
or
too
low.
Before
the
installation,
please
inspect
the
maximum
height
of
your
ceiling
and
bonnet.Too
high,
will
affect
the
efficiency
of
the
hood;
too
low,
stove
temperature
will
damage
some
parts
of
the
hood.
So
the
installation
height
requirement
is:
the
distance
between
the
bottom
of
the
hood
to
the
surface
of
the
cooktop
is
Max30”/Min27”
(as
figure
showing)
Loading...