Page 1
#14 to #10 cut here (SL)
#8 to #4 cut here *(.24-.38)
#2 to 1/0 cut here *(.38-.54)
2/0 to 250 cut here *(.53-.78)
300 to 400 cut here *(.74-.98)
* Decimal range
1
#8 - #4 *(.24-.38)
#4 - 2/0 *(.380-.580)
500 *(.94-1.175)
Select correct cut-off ring
for the cable being used.
#14 - #8 (SL)
14 8
8 4
4 2/0
SHC 3831
ROCKET
14 8
8 4
4 2/0
14 10
8 4
2 1/0
2/0 250
300 400
500
HOMAC FSS500-C
#14 - #8 (SL)
#8 - #4 *(.24-.38)
#4 - 2/0 *(.380-.580)
* Decimal range
Danger of Electric Shock! Installation of this product must be performed
by trained installers in accordance with all applicable local, state and
national electrical codes, installation standards and safety rules.
INSTALLATION INSTRUCTIONS
for "Flood-Seal"® Street Light Tap Kit
Catalog No. SL 3-2 K
• Eliminates taping: labor and material costs are significantly reduced.
• Maintains watertight and full insulating value in all direct buried, underground network tap connections.
WARNING
Cut off rocket sleeve and cap
2 4
at tip of arrow, leaving
correct cable size showing
on opened
rocket and
cap.
Wipe cable clean. Bevel the
3
end of cable insulation to
ease installation.
Apply silicone grease to end
of cable and to cut opening
of insulating sleeve. Slide
cut rocket and cap over
prepared cable ends.
Strip cable insulation to
5
install connector, baring
approximately 3/4-1” of
conductor.
3/4-1”
Install connector.
6
Apply silicone to open
7
edge of rocket sleeve.
SLIDE TOGETHER.
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
© 2012 Thomas & Betts. All Rights Reserved.
INSTALLATION INSTRUCTIONS
for "Flood-Seal"® Street Light Tap Kit
#14 to #10 cut here (SL)
#8 to #4 cut here *(.24-.38)
#2 to 1/0 cut here *(.38-.54)
2/0 to 250 cut here *(.53-.78)
300 to 400 cut here *(.74-.98)
* Decimal range
1
#8 - #4 *(.24-.38)
#4 - 2/0 *(.380-.580)
500 *(.94-1.175)
Select correct cut-off ring
for the cable being used.
#14 - #8 (SL)
14 8
8 4
4 2/0
SHC 3831
ROCKET
14 8
8 4
4 2/0
14 10
8 4
2 1/0
2/0 250
300 400
500
HOMAC FSS500-C
#14 - #8 (SL)
#8 - #4 *(.24-.38)
#4 - 2/0 *(.380-.580)
* Decimal range
• Eliminates taping: labor and material costs are significantly reduced.
• Maintains watertight and full insulating value in all direct buried, underground network tap connections.
Cut off rocket sleeve and cap
2 4
at tip of arrow, leaving
correct cable size showing
on opened
rocket and
cap.
Wipe cable clean. Bevel the
3
end of cable insulation to
ease installation.
Thomas & Betts Corporation
Catalog No. SL 3-2 K
Apply silicone grease to end
of cable and to cut opening
of insulating sleeve. Slide
cut rocket and cap over
prepared cable ends.
Strip cable insulation to
5
install connector, baring
approximately 3/4-1” of
conductor.
Memphis, Tennessee
www.tnb.com
WARNING
Danger of Electric Shock! Installation of this product must be performed
by trained installers in accordance with all applicable local, state and
national electrical codes, installation standards and safety rules.
Install connector.
6
Apply silicone to open
7
edge of rocket sleeve.
SLIDE TOGETHER.
3/4-1”
0014795 A
118_R3
Page 1 of 1
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
© 2012 Thomas & Betts. All Rights Reserved.
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
0014795 A
118_R3
Page 1 of 1
Loading...