Page 1
• RUS APPROVED
• WIRE RANGE: #6 - 350MCM
• DOUBLE CABLE CAPACITY
• HALVES SPACE REQUIREMENT
• WATERTIGHT & FULLY INSULATED
2nd RING: #8 - #4 *(.24-.38)
WIRE RANGE: TWO # 4
TO TWO 1/0 STR
SWEETHEART OUTLET
USE ROCKET #CST 3095
WIRE RANGE:
# 6-350MCM
3rd RING: #2 - 1/0 *(.38-.54)
4th RING: 2/0 - 250 *(.53-.78)
4th RING: 2/0 - 250 *(.53-.78)
3rd RING: #2 - 1/0 *(.38-.54)
2nd RING: #8 - #4 *(.24-.38)
1ST RING: #4 - 2/0 *(.38-.56)
2ND RING: 2/0 - 250 *(.56-.74)
3RD RING: 250 - 350 *(.74-.98)
Danger of Electric Shock! Installation of this product
must be performed by trained installers in accordance
with all applicable local, state and national electrical
codes, installation standards and safety rules.
INSTALLATION INSTRUCTIONS
FOR “FLOOD-SEAL”® MECHANICAL CONNECTOR
SERIES “SHC” INSTRUCTION SHEET
STEP TWO
Remove cable insulation (pencilling is
recommended) then slip the “Flood-Seal”
rocket over the cables. Figure B.
1st RING: #14 - #10 (S/L)
CST 3095
STEP THREE
When inserting the service cables into
the Sweethert Outlet, both may be
inserted at the same time. If during
1st RING: #14 - #10 (S/L)
* DECIMAL RANGE
initial installation, street light wire
capability is desired, both it and the
feeder cable may be inserted at the
same time. Figure C. The street light
wire may also be added at a later date.
NOTE: CABLE RANGE WHEN
UTILIZING STREET LIGHT TAP IS, 1/0
TO 350 MCM.
WARNING
®
B
C
D
SHC 3830
FEEDER OUTLET
USE ROCKET #SHC 3830
STEP ONE
First remove the “Flood-Seal”® EPDM
rockets from the connector. Note that there
are two congurations of rockets. Rocket No.
CST 3095 accommodates the space saver
Sweetheart Outlet for service cables. Rocket
No. SHC 3830 accommodates the “feeder”
cable outlet with exclusive no cost street
light option. Then, referring to the embossed
markings on the rocket cut off rings, select
the proper rings and cut. Figure A. Open
rocket tower cut offs only for the number of
cables to be installed initially.
2ND RING: #8 - #6 *(.24-.30)
1ST RING: #14 - #8 S/L
* DECIMAL RANGE
A
CONTINUED
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
Thomas & Betts Corporation
© 2012 Thomas & Betts. All Rights Reserved.
Tighten set screws in accordance with
torque chart. Figure D.
WIRE SIZE TORQUE
#6 to #4 ..................120 in./lbs. or 10 ft. -lbs.
#2 to 350 MCM ...... 240 in./lbs. or 20 ft. -lbs.
STEP FOUR
Slip the “Flood-Seal”® EPDM rockets over
the connection and onto the shoulder of
the bus until the sleeve butts against
connector bar for a fully insulated and
watertight installation. Figure E.
NOTE: For full insulating valve, any outlet
not in use must be covered with the
insulating rocket provided. To re-install
uncut rocket on bar, squeeze rocket barrel
to expel air and assemble onto outlet
shoulder.
Memphis, Tennessee
www.tnb.com
E
0038638 A
176_R3
Page 1 of 1
Loading...