Thinklogical Velocityrgb System-9 Quick Start Guide
Video Extension System -
Contents
Upon receiving your Thinklogical™
VelocityRGB Extender Transmitter
VelocityRGB Extender Receiver
HD15M to HD15M Cable, 2 Meters (CBL-000020-002MR) – Qty 1
3.5 mm Audio cable (CBL-000016-002MR) – Qty 2
RS-232 Serial Cable (CBL-000017-002MR) – Qty 1
Universal AC Power Adapters (PWR-000022-R) – Qty 2
RGB Extender Product Manual
STEP 6
Local keyboard and mouse
If desired, connect a local VGA
monitor to the Transmitter with an
HD15M to HD15M cable.
Thinklogical’s™ Video Extension System-9 supports RGB video formats up to 165 MHz and provides high resolutio n video extension for secure compute r installations. It is now
possible to position your remote monitor in any setting from office to lecture hall to boardroom while keeping the comp uter secu r e i n a r e m o t e , controlled location. With dual RGB outputs on the
Receiver, the video source can be distributed to two separate displays, eliminating the need for an external distribution amplifier.
All physical connections to the product use industry-standard connectors.
STEP 7
Connect the supplied AC Power
Adapter (PWR-000022-R) to the
Transmitter unit and plug it into a
standard AC source.
Power Supply
When lit, the green LED indicates
that +5VDC power is applied.
(Applies to both Tx and Rx units.)
STEP 4
Connect the fiber optic cables between the
Transmitter and Receiver Units (up to 1000
meters). Do not kink or pinch the cables and be
sure to keep all bend radii to less than 3 inches.
Both units feature a DB9 Serial
Port to support serial connections
from the CPU to the Transmitter
and from the Receiver to the
user’s serial device.
Local
Display
Powered by
MRTS
Technology
TO LOCAL
DISPLAY
LOS
FROM CPU
Velocityrgb
Transmitter
LINE IN
MIC OUT
The Transmitter and
Receiver USB ports are
for firmware upgrades
Video Extension System - 9
SERIAL PORT
DOWNLOAD
available from
Thinklogical™.
CNTRL
enter
Transmitter
FIBER
L1
L2
POWER
5VDC
_
+
DVI-D Connector 1 DVI-D Connector 2
RGB from CPU
Audio OUT
Audio IN
STEP 8
Turn on the CPU last.
Verify that all system
features are functioning
properly.
VGA 1VGA 2
Connect the CPU’s RGB video OUT
to the Transmitter with the supplied
HD15M to HD15M cable (CBL-000020-
002MR) and connect the CPU’s audio
IN/OUT with standard 3.5mm audio
cables. Connect the DB9 Serial Port
from CPU to TX, if used.
STEP 1
STEP 5
Install one or two VGA
monitors by connecting
their HD15 cables to the
VGA 1 and/or VGA 2
ports on the Receiver.
When lit, the LOS
(Loss Of Signal) LED
on each unit indicates
loss of a valid video
VGA 2
VGA 1
Connect your audio input/output
devices to the Receiver’s
3.5mm audio ports and, if used,
connect the DB9 Serial Port
from Rx to device.
VGA 2
LOS
VGA 1
signal.
Powered by
MRTS
Technology
STEP 2
LINE OUT
Velocityrgb
Receiver
MIC IN
Optical Fiber Ports available for
ST-, SC- or LC-type connectors.
FIBER
L2
SERIAL PORT
Video Extension System - 9
CNTRL
DOWNLOAD
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
L1
POWER
5VDC
_
+
Receiver
enter
STEP 3
Connect the supplied AC Power Adapter
(PWR-000022-R) to the Receiver and plug it
into a standard AC source.
Power Supply
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: support@thinklogical.com
Visit us online at www.thinklogical.com for more product information, current updates
and the complete line of Thinklogical products.
TM
Rev.B 5/09
Loading...