Thinklogical Velocitykvm-4 Quick Start Guide

Multi-Mode Fiber Extension System – DVI Two Display

T

U

V

D

I O

STEP 10: Turn on the
Source (CPU) last. Verify
that all system features are
functioning properly.

S

U

u

A

u

A

S

P

S

P

S

U

S

U

STEP 6: A DVI-D cable (CBL000009-002MR) is

included. Connect it to the CPU DVI Video Card

Note:

Be sure to
leave adequate ventilation
space on both sides of
the units (2” minimum),
especially if the units are
being stacked

B

2

.
O

d

io

d

io

K

/

2

/

2

M

B

H
1

.

B

VelocityKVM-4 Transmitter

W

P

R

P

C

L

I

C

K

N

0

T

U

I

N

r

e

I

d

y

b

o

a

o

u

s

e

o

u

s

e

M

)

s

e

)

o

u

y

b

d

K

/

D

(

b

d

/

1

M

(

y

K

and the other end to the VelocityKVM

Transmitter’s DVI IN connector.

W

P

R

.

B

S

2

U

L

O

F

B

S

2

.

U

0

L

O

F

0

The Thinklogical™ Velocitykvm-4 Multi-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by two multi-mode fiber optic
cables (or by one or two optional single-mode fibers). The transmitter unit connects to the computer with standard cables and the receiver unit provides
connections to the user interface devices. The Velocitykvm-4 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports and
USB 1.1. USB 2.0 (high speed up to 480Mbps) is optional.

STEP 7: (Optional) Connect your
local monitor cable (not included) to

PS/2 Connector USB HID Connector

the DVI OUT connector on the
VelocityKVM Transmitter.

STEP 8: If desired, connect your local
keyboard and mouse by inserting the PS/2 or
USB HID connectors into the VelocityKVM
Transmitter’s local devices receptacles.

Verify that all system
features are functioning
properly. Turn on the
Source (CPU) and
Display Devices last.

VEL-U00M04-SCRX

n

L

1

I IN

V

D

V

I IN

D

L

2

T

U

O

V

D

I

L

L

1

2

STEP 4: Connect your Multi­Mode Fiber Optic cables

R

A

T

D

P

U

S

P

ID

S

2

P

U

C

M

O

R

A

C

L

O

F

L

E

IN

L

IN

H

T

U

O

IC

M

1

.

1

B

S

U

ID

S

U

B

H

E

V

E

D

PS/2

Keyboard/

USB 1.1

Mouse

T

R

O

L

P

IA

S

E

C

S

T

O

H

T

N

L

R

C

-

-

2

4

0

V

,

0

.

5

1

0

0

A

R

!

I

T

N

U

A

O

h

w

,

5

0

/

6

0

z

H

s

a

c

e

e

p

la

it

d

e

m

t

y

p

e

a

T

2

A

,

2

5

0

.

r

a

t

g

in

f

u

s

e

C

A

V

between the Transmitter and
Receiver units as shown.
(1 or 2 Single-Mode fibers can
also be used, depending on the

Audio OUT
Audio IN

USB HID

model and required fiber
length.)

STEP 5: Connect
your KVM devices

L1: Video and Data Tx to Rx
L2: Data Rx to Tx

to the CPU using
the cables supplied
in KIT-000005-R.

STEP 1: Ensure that the POWER ON/OFF switch is
in the OFF position (0) on both the Tx and Rx units.
Connect the supplied AC Power Cords to both units
and plug them into a standard AC supply. LEAVE
BOTH SWITCHES IN THE OFF POSITION.

L

L

1

L

1

C

D

T

U

D

V

I O

D

2

L

2

T

U

O

V

D

I

VelocityKVM-4 Receiver

T

R

O

L

P

IA

R

S

E

VEL-U00M04-SCRX

T

U

E

O

IN

L

IN

IC

M

ID

S

B

H

U

P
S
2

e

n

s

e

p

R

!

I

T

N

U

A

O

C

U
P
D

S

T

O

H

A
T

1

.

1

B

S

U

E
S

T

N

C

L

R

,

0

.

5

1

0

0

A

-

-

2

4

0

V

a

c

e

la

it

h

w

z

H

,

5

0

/

6

0

d

e

m

t

y

p

e

a

2

T

2

A

,

.

r

a

t

g

in

f

u

s

C

A

5

0

V

Note: In order to
avoid possible exposure
to laser energy, it is good
practice to attach the
fiber optic cables prior to
applying power to the
unit.

CONTENTS

Upon receiving your Thinklogical™
Velocitykvm-4 Extender you should
find the following items:

VelocityKVM Extender Transmitter
VelocityKVM Extender Receiver
2 AC power cords, PWR-000006-R

(International connections may differ.)

VelocityKVM Extender Cables:

1

DVI-D Male Cable, 2 meters, CBL000009-002MR

1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R

VelocityKVM Extender Product Manual

All physical connections to the product use industry-standard connectors.

TM

PHONE: [phone]
WEBSITE: www.thinklogical.com
EMAIL: [e-mail]

STEP 2: Connect your desktop devices

(monitors, keyboard, mouse, etc.) to the

Receiver using standard cables.

Visit us online at www.thinklogical.com for more
product information, current updates and the
complete line of Thinklogical products.

RACK-MOUNT OR DESK-TOP
OPTIONS: Like all Thinklogical™

KVM extenders, the VelocityKVM-4
can be mounted in a standard EIA 19"
rack or on a shelf or desk-top.

STEP 3: Turn the
Receiver unit ON.

8 Mounting bracket

screws

Velocitykvm-4

Single Head Single Link

Fiber Optic Transmitter

Each mounting bracket is secured

by four screws and can be safely

removed from the transmitter or

receiver unit for desk-top mounting.

Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.

2 Mounting bracket screws

in four places.