Thinklogical Velocitykvm-38 Quick Start Guide
Velocitykvm-38
Multi-Mode Fiber Extension – DVI Two Display
QUICK START GUIDE
STEP 7: (Optional) Connect your local monitor 1 and/or local monitor 2
DVI cables (not included) to the DVI OUT 1 DUAL-LINK and DVI OUT 2
DUAL-LINK connectors on the VelocityKVM Transmitter.
7
FOL
P
Local
Display 1
(Dual-link)
STEP 10: Turn on the
Source (CPU) last. V erify
that all system features are
functioning properly.
Local
Display 2
(Dual-link)
VEL-U00M 38-SCTX
VelocityKVM-38 Transmitter
PWR
C
CLINK
10
USB 2.0
Audio OUT
Audio IN ◄
P
PS/
USB HID (Kybd/Mouse
USB 1.1 (Kybd/M
STEP 6:
Two DVI -D Dual-link cab les (CBL-00 0023-00 2MR) are included.
Connect one from the CPU DVI 1 Video Card to the V elocityKVM
Transmitter’s DVI IN 1 DUA L-LINK port.
Connect the other from the CPU DVI 2 Video Card to the
VelocityKVM Transmitter’s DVI IN 2 DUAL-LINK port.
Note: Be sure to leave
adequate ventilatio n space
on both sides of the units
(2” minimum), especially if
the units are being stacked
S/2 Keyboar
2 Mouse
DVI IN 1 Dual-lin
D
V
►
d
ouse)
I IN 2 Dual-link
)
5
k
6
PWR
U
S
FOL
B 2.0
L
1
DVI IN 1 DUAL-LIN
L
1
L
2
L
2
DVI OUT 1 DUAL-LINK
Each Thinklogical™ Velocitykvm-38 Multi-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by four multi-mode fiber
optic cables (or by one optional single-mode fiber). The transmitter unit connects to the computer with standard cables and the receiver unit provides
connections to the user interface devices. The Velocitykvm-38 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports and
USB 1.1. Options include USB 2.0 (high speed up to 480Mbps).
PS/2 Con nector USB HID Connector
L
3
L
2
DVI OUT 1 DUAL-LINK
K
L
2
L
1
L
1
L
4
DVI OUT 2 DUAL-LINK
DVI OUT 1
DUAL-LINK
L
3
L
4
L
4
L
3
L
4
4
L
3
L
5
DVI IN 2 DUAL-LIN
L
5
L
5
UT 2
DVI O
DUAL-LINK
ORT
SER IAL P
K
DVI OUT 2 DUAL-LINK
STEP 4: Connect your
Multi-Mode Fiber Optic
cables between the
Transmitter and Receiver:
L1/Tx to L1/Rx
L2/Tx to L2/Rx
L3/Tx to L3/Rx
L4/Tx to L4/Rx
L5/Tx to L5/Rx
L1: Data Tx to Rx and Video 1 Primary
L2: Data Rx to Tx
L3: Video 1 Secondary
L4: Video 2 Primary
L5: Video 2 Secondary
SER IAL POR
L
5
T
LINE IN
MIC OUT
LINE OU
MIC I
▲
Audio
OUT
Audio IN►
T
N
HID
Keyboard/
USB HID
STEP 8: If desired, connect your local
keyboard and mouse by inserting the PS/2 or
USB HID connectors into the VelocityKVM
8
P
S
2
PS/2
Mou se
Transmitter’s local devices receptacles.
UPDATES
USB1.
1
DEV
LOCALFROM CPU
USB 1.1
USB HID
STEP 5: Connect
your KVM devices
to the CPU using
the cables supplied
USB
in KIT-000005-R.
HID
5
VEL-U00M38-SCRX
VelocityKVM-38 Receiver
P
S
2
1
USB1.
CAUTION! Replace with same type and rating fuse
HOS
T
CNTRL
100-240V-,0.5A, 50/60 H
CAUTION! Repl
U
P
D
HOS
T
A
T
E
S
CNTRL
a
100-240V-,0.5A, 50/60 H
9
.
T 2A ,250VA
z
C
1
STEP 1: Ensure that the POWER ON/OFF switch is
in the OFF position (0) on both the Tx and Rx units.
Connect the supplied AC Power Cords to both units
and plug them into a standard AC supply. LEAVE
BOTH SWITCHES IN THE OFF POSITION.
ce with same type and rating fuse
T 2A ,250VA
z
.
C
STEP 9: Turn the
Transmitter unit ON.
2
CONTENTS
Upon receiving your Thinklogical™
Velocitykvm-38 Extender, you
should find the following items:
VelocityKVM Extender Transmitter
VelocityKVM Extender Receiver
2 AC power cords, PWR-000006-R
(International connections may differ.)
VelocityKVM Extender Cables:
2 DVI-D Male Dual-link Cables, 2 meters, CBL-000023-002MR
1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R
VelocityKVM Extender Product Manual
All physical connections to the product use industry-standard connectors.
Copyright c 2 009. All rights reserved. P rinted in th e U.S.A. All t rademarks and service marks are the property of their respective owne rs.
Display
DVI OUT 1
Dual-link
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: support@thinklogical.com
2
DVI OUT 2
Dual-link
Visit us online at www.thinklogical.com for more
product information, current updates and the
complete line of Thinklogical™ products.
STEP 2: Connect your desktop devices
(monitors, keyboard, mouse, etc.) to the
Receiver using standard cables.
VELOCITY- 38_Quick_Start_Rev_B
PS/2 or HID
Connectors
RACK-MOUNT OR DESK-TOP
OPTIONS: Like all Thinklogical™
KVM extenders, the VelocityKVM-38
can be mounted in a standard EIA 19"
rack or on a shelf or desk-top.
2 Mounting bracket screws
in four places.
STEP 3: Turn the
3
8 Mounting bracket
Receiver unit ON.
screws
Velocitykvm-38
DVI TWO DIS PLA Y
Fiber Optic Transmitter
Each mounting bracket is secured
by four screws and can be safely
removed from the transmitter or
receiver unit for desk-top mounting
after power has been removed from
the unit.
Loading...