Thinklogical Velocitykvm-35 Quick Start Guide
Velocitykvm-35
Multi-Mode Fiber Extension – Three DVI Displays
Multi-Mode Fiber-Optic
QUICK START
GUIDE
STEP 9: Turn on the Source
(CPU) last. Verify that all
system features are
functioning properly.
VelocityKVM-35 Transmitter
PWR
C
P
CLINK
Cable Guide:
L1: Data Tx to Rx and Video 1
L2: Data Rx to Tx
L3: Video 2
L4: Video 3
L2L
L
1
FOL
DVI IN
3
1
9
USB 2.0
UT►
Audio O
Audio IN◄
PS/2 Keyboard
PS/2 Mous
USB HID (
USB
e
K
1.1 (Kybd/Mouse)
ybd/Mouse
L
1
)
5
3
L
3
L
2
6
STEP 6: Three DVI-D cables (CBL-000009-002MR) are
included. Connect one ea ch to the CPU’s DVI 1, 2 and 3
Video Cards and the other ends to the VelocityKVM
Note: Be sure to
leave adequate ventilation
space on both sides of the
units (2” minimum),
especially if the units are
being stacked
Transmitter’s DVI IN 1, 2 and 3 ports.
R
P
W
USB 2.0
FOL
L2L
1
L1L
L
2
DVI OUT 1
4
Each Thinklogical™ Velocitykvm-35 Multi-Mode Fiber Optic System consists of a transmi tter unit and a receiver unit connected by four multimode fiber optic cables. The transmitter unit connects to the computer with standard cables and the receiv er unit provides connections to the user
interface devices. The Velocitykvm-35 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports and USB 1.1. USB
2.0 (high speed up to 480Mbps) is optional.
STEP 7: If desired, connect your local
keyboard and mouse by inserting the PS/2 or
7
USB HID connectors into the VelocityKVM
Transmitter’s local devices receptacles.
STEP 8: Turn the
Transmitter unit ON (1).
8
Local PS/2
Connectors
P
S
2
LOCALFROM CPU
PS/2
Kybd/
Mouse
USB 1.1
UPDATES
USB1.
1
USB HID
STEP 5: Connect
your KVM devices
to the CPU using
USB
the cables supplied
HID
in KIT-000005-R.
DEV
5
VelocityKVM-35 Receiver
U
P
D
A
T
E
1
S
USB HID
P
S
2
USB1.
CAUTION! Replace with same type and rating fuse
S
T
H
O
CNTRL
100-240V-,0.5A, 50/60 H
CAUTION! Replace with same type and rating fuse
HOS
T
CNTRL
100-240V-,0.5A, 50/60 H
z
.
T 2A ,250VA
C
1
STEP 1: Ensure that the POWER ON/OFF switch is
in the OFF position (0) on both the Tx and Rx units.
Connect the supplied AC Power Cords to both units
and plug them into a standard AC supply. LEAVE
BOTH SWITCHES IN THE OFF POSITION.
.
T 2A ,250VA
z
C
DVI IN 2
L
4
DVI OUT 2
Local USB HID
Connectors
L
4
DVI IN
3
L
4
4
L
3
L
3
DVI OUT 3
SER IAL POR
STEP 4: Connect your Multi-Mode Fiber
Optic cables between the Transmitter
and Receiver units.
SER IAL POR
T
LINE IN
MIC OUT
T
LINE OU
MIC I
HID
▲
Audio
OUT
Audio IN►
T
N
CONTENTS
Upon receiving your Thinklogical
Velocitykvm-35 Extender, you
should find the following items:
VelocityKVM Extender Transmitter
VelocityKVM Extender Receiver
2 AC power cords, PWR-000006-R
(International connections may differ.)
VelocityKVM Extender Cables:
3 DVI-D Male Cables, 2 meters, CBL-000009-002MR
1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R
VelocityKVM Extender Product Manual
All physical connections to the product use industry-standard connectors.
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
T
M
DVI
2
Display 1
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: support@thinklogical.com
Visit us online at www.thinklogical.com for more
product information, current updates and the
complete line of Thinklogical™ products.
PS/2 or USB
connectors
3
STEP 2: Connect your desktop
devices (monitors, keyboard,
3
2
mouse, etc.) to the Receiver
using standard cables.
RACK-MOUNT OR DESK-TOP
OPTIONS: Like all ™
KVM extenders, the VelocityKVM-35
can be mounted in a standard EIA 19"
STEP 3: Turn the
Receiver unit ON (1).
8 Mounting bracket
screws
rack or on a shelf or desk-top.
Velocitykvm-35
Three Head Sing le Link
Fiber Optic Tran smitter
Each mounting bracket is secured
by four screws and can be safely
removed from the transmitter or
VELOCITY -35_Quick_Start_Rev_B
receiver unit for desk-top mounting
after power has been removed from
the unit.
2 Mounting bracket screws
in four places.
Loading...