Thinklogical Velocitykvm-4, Velocitykvm-5, Velocitykvm-8, Velocitykvm-24, Velocitykvm-28 User Manual

...

Download

Fiber-Optic Extension Systems

Velocitykvm-4, 5, 8, 24, 28, 34, 35 & 38

Single & Dual-Link/Single & Multi-Mode

Thinklogical, LLC®

100 Washington Street

Milford, Connecticut 06460 U.S.A.

Telephone: 1-203-647-8700

Fax: 1-203-783-9949

www.thinklogical.com

Thinklogical, LLC ® 100 Washington Street Milford, Connecticut 06460 U.S.A. Telephone: 1-203-647-8700 Fax: 1-203-783-9949

www.thinklogical.com

All trademarks and service marks are property of their respective owners.

Subject: VelocityKVM Fiber-Optic Extension Product Manual Revision: B, January, 2014

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 2

Table of Contents

PREFACE................................................................................................................................... 5

Conventions Used in this Manual ............................................................................................ 5

Laser Information ...................................................................................................................... 5

INTRODUCTION ........................................................................................................................ 6

The Logical Solution ................................................................................................................. 6

Theory of Operation .................................................................................................................. 6

The Fiber Extension System .............................................................................................. 6

Multi-Mode Fiber ............................................................................................................. 7

Single-Mode Fiber ........................................................................................................... 7

Options Part Numbers ........................................................................................................ 8

System Features ....................................................................................................................... 9

VelocityKVM Extender Options ................................................................................................ 9

Technical Specifications (Table 1) ......................................................................................... 13

Velocity Unbalanced Audio Specifications (Table 2) ............................................................ 14

VelocityKVM-5 Supported RGB Resolutions (Table 3) ......................................................... 15

HARDWARE ............................................................................................................................ 16

Contents .................................................................................................................................. 16

Desktop or Rack Mount Device ......................................................................................... 16

Cooling ............................................................................................................................... 17

Front Panel Display and Buttons ...................................................................................... 17

Connecting the VelocityKVM Extender ................................................................................. 17

Types of Connectors .............................................................................................................. 17

Fiber Cable ......................................................................................................................... 17

Transmitter ......................................................................................................................... 17

Receiver .............................................................................................................................. 17

Receiver Serial Port ........................................................................................................... 18

Rear Panel Views and Hardware Connections ...................................................................... 19

Typically Used Fiber and Copper Cables ........................................................................ 19

Peripheral and Update Ports ............................................................................................ 19

Fiber and Video Ports ....................................................................................................... 20

Cables ...................................................................................................................................... 24

Installation ............................................................................................................................... 26

Set Up ................................................................................................................................... 26

Firmware Upgrades ........................................................................................................... 26

Front Panel Usage .................................................................................................................. 26

General Front Panel Usage ............................................................................................... 27

SFP LOS and SFP Des OK Signals ............................................................................... 27

SFP LOS and SFP Des OK Signals (Table 4) ................................................................ 28

Saving Changes ................................................................................................................. 32

Restoring Factory Defaults ............................................................................................... 33

Naming the Transmitter Unit ............................................................................................. 34

REGULATORY & SAFETY COMPLIANCE .............................................................................. 35

Safety Requirements .............................................................................................................. 35

Symbols Found on Our Products ..................................................................................... 35

Regulatory Compliance ..................................................................................................... 35

North America .................................................................................................................... 35

Australia & New Zealand ................................................................................................... 36

European Union ................................................................................................................. 36

Declaration of Conformity ............................................................................................ 36

Standards with Which Our Products Comply ....................................................................... 36

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 3

Supplementary Information.................................................................................................... 36

Product Serial Number ........................................................................................................... 37

Connection to Our Products .................................................................................................. 37

HOW TO CONTACT US ........................................................................................................... 38

Customer Support .................................................................................................................. 38

Website ................................................................................................................................ 38

Email ................................................................................................................................... 38

Telephone ........................................................................................................................... 38

Fax ...................................................................................................................................... 39

Product Support ...................................................................................................................... 39

Limited Warranty Information ........................................................................................... 39

APPENDIX A: Thinklogical’s Full Line of VelocityKVM Extenders ...................................... 41

Part Number Reference Guide ......................................................................................... 44

APPENDIX B: Quick Start Guides .......................................................................................... 45

VelocityKVM-4 ................................................................................................................... 45

VelocityKVM-5 ................................................................................................................... 46

VelocityKVM-8 ................................................................................................................... 47

VelocityKVM-24 ................................................................................................................. 48

VelocityKVM-28 ................................................................................................................. 49

VelocityKVM-34 ................................................................................................................. 50

VelocityKVM-35 ................................................................................................................. 51

VelocityKVM-38 ................................................................................................................. 52

APPENDIX C: Automatic Fail-Over Option ............................................................................ 53

APPENDIX D: Keyboard Mouse Audio Control Options...................................................... 55

APPENDIX E: Separate Data Path, Separate Audio Path and Multi-Path Video Options ... 56

APPENDIX F: EDID Definitions and DDC Modes .................................................................. 60

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 4

PREFACE

Conventions Used in this Manual

Throughout this manual you will notice certain conventions that bring your attention to important information. These are Notes and Warnings. Examples are shown below.

Note: Important Notes appear in blue text preceded by a yellow exclamation point symbol,

as shown here.

A note is meant to call the reader’s attention to helpful information at a point in the text that is relevant to the subject being discussed.

Warning! All warnings appear in red text preceded by a red stop sign, as shown here.

A warning is meant to call the reader’s attention to critical information at a point in the text that is relevant to the subject being discussed.

Laser Information

VelocityKVM Extenders

Modules

are designed and identified as

SFP

Class 1 LASER products.

Class 1 Lasers

Fiber-Optic Cables

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 5

INTRODUCTION

The Logical Solution

VelocityKVM Fiber-Optic Extension Systems

visual applications that require video as well as peripheral support. The system allows users, via

fiber-optic cable, to station and operate video monitors and peripherals up to 40 kilometers away from the controlling computer, securely and without loss of resolution. The VelocityKVM system is designed to support PS2, full duplex stereo audio, serial (RS-232) and USB 1.0 (HID).

Available options include:

• Single-Mode or Multi-Mode Optics

• USB HID only (eliminates USB 2.0 for added security)

• Separate Data Paths for keyboard/mouse (See Appendix E, pg. 56)

• Separate Audio Paths (See Appendix E, pg. 56)

• Multi Path (Multiple Video Paths) (See Appendix E, pg. 56)

• RS-422 serial port for controlling broadcast equipment

• Automatic Fail-Over (See Appendix C, pg. 53)

• Professional Audio TOSLINK, AES and S/PDIF plug-in modules (pg. 12)

VelocityKVM products are ideally suited for a wide range of applications in the broadcast and postproduction field, as well as command/control centers, universities, large scale digital signage and other commercial KVM applications.

See Option Configuration Diagrams (pgs. 10-12) and Appendix A, Complete Line of Thinklogical’s VelocityKVM Extenders (pg. 41).

are designed for high performance

Theory of Operation

MRTS Technology 6.25 Gbps. Allows Full Frame Rate Transmission of Uncompressed DVI

Powered by Thinklogical’s cutting edge, patent-pending MRTS (Multi Rate Transmission System) Technology, this KVM extension system transports every frame of a DVI or RGB video stream seamlessly with no compression or dropped frames. In addition, all high speed peripherals function with no latency.

The VelocityKVM Extension System

The VelocityKVM Extension System has a simple transmitter/receiver design which allows for ease of installation and straight-forward deployment. Incorporating standard SFP+ transceivers, the transmitter and the receiver can be connected by a multi-mode or single-mode fiber optic cable, depending on the user’s needs. The transmitter unit connects to the CPU with the supplied peripheral cables. In addition, a local video, keyboard and mouse port is available on the transmitter. The receiver unit provides connections to the various user interface devices.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 6

The Fiber System

Each system includes a transmitter and a receiver connected by fiber optic cables. The transmitter connects to the source computer with standard cables and the receiver provides connections to the user interface devices. Standard VelocityKVM Extenders support PS2, full duplex stereo audio, serial

(RS-232), USB HID and USB 2.0.

Why Fiber?

In heavy-volume, metropolitan area networks, the limit on how much bandwidth or data that can be carried across a copper line can become a bottleneck for enterprise access and ultimately, for revenue.

Fiber Optic Cable alleviates this problem by offering substantially greater bandwidth.

Multi-Mode Fiber

Transmission Distance (up to 350m using 50/125µm fiber)

Multi-mode is designed for transmission distances such as those found within a single building or facility and thus, is ideal for multi-channel television broadcast systems. Multi-mode may be used to send video signals from room to room or floor to floor. The Multi-Mode VelocityKVM Extender allows video and peripheral transmission distances up to 350 meters using 50/125µm fiber, making it an ideal solution for in-house applications.

Single-Mode Fiber

Transmission Distance (up to 40 kilometers)

Single-mode is designed for long distance transmissions and thus, is ideal for multi-channel broadcast systems. Single-mode may be used to send video signals from workstation to workstation, from building to building, or from studio to transmitter (STL) with a video resolution of 1920 x 1200. Using 9µm fiber with SM/UPC connectors, the Single-Mode VelocityKVM Extender allows video and peripheral transmission distances up to 40 kilometers, (25 miles) making it an ideal solution for metropolitan area networks and most other applications.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 7

Advanced Top Quality Video Transmission

Fiber optic cable has emerged as a logical solution for next-generation signal routing. The VelocityKVM product family harnesses this capability and ensures long distance, error-free transmission with no frame or bit dropping and complete immunity to interference. The end result is no degradation of the video

or peripheral signal whatsoever.

Options Part Numbers

Each model’s part number indicates features included on that particular model. See pages 10-12 for the full line of VelocityKVM Extender options. Also see page 44 for more on numbering formats.

VEL-WR0M04-SCTX:

VelocityKVM 1 DVI Display Transmitter with USB HID, USB 2.0 and redundant, multi-mode fiber paths

DVI IN

DVI O

L2'

SER IAL POR

STEREO EMITTER

INPUT

LINE IN

MIC OUT

P S 2

HID

LOCAL

OM CP

UPDATES

USB HID

LIN

USB

HOS

DEV

2.0

CAUTION! Replace with same type and

HOST

CTRL

100-240V-,0.5A, 50/60 H

rating fuse.

USE ONLY WITH 250V FUSE

T 2A ,250VA

VEL-WR0M04-SCTX: VEL indicates the Velocity line of extenders. The part number’s leading W indicates

USB HID and USB 2.0 only (USB 1.1 is not supported). This is the standard USB configuration for our Velocity line. R indicates redundant fiber paths. 0 is a place holder. M indicates Multi-Mode optics.

04 designates our 1 DVI Display model. SC indicates SC-Type fiber connectors. TX indicates that this unit

is a Transmitter.

VEL-H0DM24-LCRX:

VelocityKVM 2 DVI Display Receiver with USB HID only and separate multi-mode data fiber paths

VEL-H0DM24-LCRX: VEL indicates the Velocity line of extenders. The part number’s leading H indicates the

USB HID Only option (USB 2.0 is not supported). 0 is a place holder. D indicates Separate Data Paths.

M indicates Multi-Mode optics. 24 designates our 2 DVI Display model. LC indicates LC-Type fiber

connectors. RX indicates that this unit is a Receiver.

Note: Thinklogical will no longer support the hardware required for USB 1.1. Thinklogical will continue software support for all USB 1.1 units. Contact

support@thinklogical.com.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 8

System Features

Each VelocityKVM Fiber system includes the following features:

• Supports all single-link DVI video resolutions (VelocityKVM-5 analog RGB resolutions as well).

• Supports all Dual-Link DVI resolutions (VelocityKVM-8, -28, -38).

• 6.25 Gbps signal transmission via fiber optic cable; No RF interference.

• Requires one to five fiber optic cables, depending on model and application.

• Flawless image quality with no frame dropping.

• Local KVM connections on transmitter.

• Additional video output(s) on the receiver.

• Extends KVM, audio and serial signals up to 350 meters using 50/125µm multi-mode fiber and up

to 1000 meters using type OM4 fiber.

• Extends KVM, audio and serial signals up to 40 kilometers using single mode optics.

• USB HID compliant, 4-port hub.

• BNC Stereo Emitter (3D)

• Full duplex stereo audio

• USB 2.0 compliant (high speed 480 Mbps, 4 port hub).

• (Optional) IEEE1394 FireWire 9-pin hub (Requires 2 additional fiber optic cables.)

• (Optional) Automatic Fail-Over (see page 53)

• (Optional) Separate Data Paths for keyboard/mouse

• (Optional) RS-422 serial port for controlling broadcast equipment

• DDC2B/EDID complaint.

• Fully compatible with all of Thinklogical’s VXRouter line of products.

• Full keyboard and mouse emulation through the transmitter

• Simple plug and play

• Thinklogical’s VelocityKVM Extenders are designed and identified as Class 1 Laser products.

VelocityKVM Extender Options

VelocityKVM Extenders come with a variety of peripheral device options that include or eliminate several types of USB and FireWire, Network ports and Separate Data Paths.

The examples on pages 10 -12 are shown with the VelocityKVM-24 Tx and Rx with LC-type connectors. All extender models follow the same format for all connector types and option configurations.

The options include combinations of, with or without, such features as:

• USB HID, USB 2.0 and/or FireWire

• Separate data paths

• 10/100 NIC Network ports

• Professional audio plug-in modules (TOSLINK, AES, S/PDIF)

Note: Thinklogical will no longer support the hardware required for USB 1.1. Thinklogical will continue software support for all USB 1.1 units. Contact

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 9

support@thinklogical.com.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 10

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 11

VelocityKVM-24P DVI 2 Display/KVM Professional Audio Extender Option

The VelocityKVM-24P Professional Audio option includes six audio modules with each unit. Any two types will fit at once into each transmitter and each receiver unit. The modules include TOSLINK IN, AES IN, S/PDIF IN, TOSLINK OUT, AES OUT and S/PDIF OUT.

The VelocityKVM-24A Professional Audio option includes the same features as the -24P, but eliminates USB 2.0 for increased security (USB HID only).

VEL-24P DVI 2 Display/KVM Professional Audio Extender

Transmitter VEL-P00M24-LCTX

AES IN

TOSLINK IN

DVI IN

Receiver VEL-P00M24-LCRX

AES OUT

TOSLINK OUT

DVI

OUT 1 DD

HOST

CTRLDEV

U P

HOST

D A T E S

CTRL

CAUTION! Replace with s

100-240V-,0.5A, 50/60 H

CAUTION! Replace with same ty

100-240V-,0.5A, 50/60 H

SER IAL POR

DVI OUT 1

DVI IN

VI OUT 1

OUT 2 DD

DVI

DVI OUT 2

SER IAL POR

VI OUT

STERE EMITTER

INPUT

STEREO EMITTER

OUTPU

LINE IN

MIC OUT

LIN

MIC I

P S 2

HID

USB HID

FROM CP

LOC

P S

LIN

DEV

UPDATES

USB HID

LIN

USB

HOS

2.0

USB 2.0

ame type and rating fuse.

USE ONLY WITH 250V FUSE

T 2A ,250VA

pe and rating fuse.

USE ONLY WITH 250V FUSE

T 2A ,250VA

VelocityKVM-24P Professional Audio Modules included with each unit

TOSLINK OUT

S/PDIF OUT

AES OUT AES IN

TOSLINK IN

Also available:

VEL-24A DVI 2 Display/KVM Professional Audio Extender with USB HID only

Transmitter: VEL-A00M24-LCTX, Receiver: VEL-A00M24-LCRX

S/PDIF IN

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 12

Technical Specifications

Thinklogical VelocityKVM systems are designed to the following specifications:

TRANSMITTER

Video System 4, 8 DVI-D (2); System 24, 28, 34, 38 DVI-D

(4); System 35 DVI-D (3); System 5 DVI-I (2) Audio MIC/Line 3.5mm Jack Serial Port DB9 Female Stereo Emitter 50Ω BNC IEEE 1394* 9-Pin FireWire (optional) USB HID USB B USB 2.0 USB B USB Local Kybd. USB A USB Local Mouse USB A PS2 Keyboard MiniDIN 6 Female PS2 Mouse MiniDIN 6 Female PS2 Local Kybd. MiniDIN 6 Female PS2 Local Mouse MiniDIN 6 Female

Copper

Connectors

Firmware Updates USB B (3) Fiber Connectors LC, SC or ST

RECEIVER

Video System 4, 8, 28, 38 DVI-D (2); System 24, 34 DVI-D

(4), System 35 DVI-D (3); System 5 DVI-I (2) Audio MIC/Line 3.5mm Jack Serial Port DB9 Male Stereo Emitter BNC IEEE 1394* 9-Pin FireWire (optional) USB HID USB A (4) USB 2.0 USB A (4) PS2 Keyboard MiniDIN 6 Female PS2 Mouse MiniDIN 6 Female Firmware Updates USB B Fiber Connectors LC, SC, or ST

CBL000009-002MR, DVI-D M to M: -4, -5, -24(2), -28, -34(4), -35(3) CBL000022-002MR, HD15 to DVI-A: -5 CBL000023-002MR, DVI-D Male to Male, Dual-Link: -8, -28, -38(2) KIT-000005-R, Audio Kit, 6FT: 1 each

Electrical Cables

(supplied with

transmitters)

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 13

KIT-000005-R Audio Kit contains the following:

CBL000006-006FR 6 pin MiniDIN Male to Male Cable, 6FT (2) CBL000015-006FR USB A-B Cable, 6FT (2) CBL000016-006FR 3.5mm Male to 3.5mm Male Plug, 6FT (2) CBL000017-006FR DB9 Male to DB9 Female Cable, 6FT (1) CBL000018-006FR BNC Male to BNC Male Cable, 50Ω, 6FT (1)

Video Resolution

Power

All Single-Link DVI Resolutions: System 4, 5, 24, 34, 35 All Dual-Link DVI Resolutions: System 8, 38 Single & Dual-Link DVI Resolutions: System 28

Optical Cable

(Not supplied)

Optical Distance

Operating Temp

and Humidity

Dimensions

Weights

Supply Voltage

Consumption

Compliance

Warranty

Multi-mode Fiber Type: 50 or 62.5 µm Single-mode Fiber Type: SM/UPC, 9 µm

Up to 65 meters with Type OM1 Up to 350 meters with Type OM2 Up to 650 meters with Type OM3 Up to 1000 meters with Type OM4

0° to 50°C (32° to 122 °F), 5% to 95% RH, non-conde nsing

Height: 1.72” (4.4cm) ± .039”; .100cm Depth: 14.22” (36.19cm) ± .039”; .100cm Width: 17.49” (44.5cm) ± .039”; .100cm

Weight: 11 lbs (4.99kg) each Shipping Weight: 27 lbs (12.25 kg) Transmitter and Receiver

100-240 VAC, 47-63 Hz, Universal AC power supply

<40 Watts per unit Approvals for US, Canada, and European Union

12 months from date of purchase. Extended warranties available.

TABLE 1: Technical Specifications

TABLE 2: Velocity Unbalanced Audio Specifications

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 14

VelocityKVM-5 Supported RGB Resolutions

Active Resolution

Pixels Lines

640 448 472 66 31.2 25 Honeywell 640 480 525 60 31.5 25.175 Industry Standard 640 480 520 72 37.9 31.5 VESA 640 480 500 75 37.5 31.5 VESA 640 480 509 85 43.3 36 VESA 720 400 449 70 31.5 28.32 Industry Standard 800 600 625 56 35.1 36 VESA 800 600 628 60 37.9 40 VESA 800 600 666 72 48.1 50 VESA 800 600 625 75 46.9 49.5 VESA

800 600 631 85 53.7 56.25 VESA 1024 768 800 50 40 53.44 Folsom 1024 768 806 60 48.4 65 VESA 1024 768 800 75 60 78.75 VESA 1024 768 808 85 68.7 94.5 VESA 1280 720 750 50 37.5 74.25 Folsom 1280 720 750 60 45 74.25 CEA-861-E 1280 800 828 60 49.7 83.46 VESA GTF 1280 1024 1066 50 52.8 89.55 Folsom 1280 1024 1066 60 64 108 VESA 1280 1024 1082 60 64.8 108.88 Discreet 1280 1024 1066 75 80 135 VESA 1280 1024 1072 85 91.1 157.5 VESA 1280 1024 1063 96 102 163.277 SGI Onyx2 1366 768 795 60 47.7 85.5 VESA GTF 1400 1050 1090 50 54.5 94.61 Folsom 1400 1050 1080 60 64.8 120.78 VESA CVT-RB 1400 1050 1089 60 65.3 121.75 VESA 1400 1050 1099 96 105.4 164.5 SGI Stereo 1440 900 932 60 55.8 106.4 VESA GTF 1440 900 934 60 55.9 106.5 VESA DMT 1600 1200 1250 60 75 162 VESA 1680 1050 1089 60 65.3 146.25 VESA DMT 1920 1080 1125 25 28.12 74.25 Folsom 1920 1080 1125 50 56.25 148.5 Folsom 1920 1080 1125 60 67.5 148.5 CEA-861-E

Total

Lines

Vertical

Freq

(Hz)

Horizontal

Freq

(kHz)

Pixel Clock

Freq

(MHz)

Video Standard

TABLE 3: Velocity 5 RGB Resolutions

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 15

HARDWARE

Contents

When you receive your Thinklogical VelocityKVM Extender®, you should find the following items:

• VelocityKVM Extender Transmitter

• VelocityKVM Extender Receiver

• AC power cord, PWR-000006-R (International connections may differ) – Qty 2

• VelocityKVM Extender Cables

 Video Cable, 2 Meters – See Technical Specs, pg. 13  Audio Cable Kit (8 pcs.), 6 Feet, KIT-000005-R – Qty 1

• VelocityKVM Extender Product Manual CD

• Product Quick Start Guide

All physical connections to the product use industry-standard connectors.

Desktop or Rack Mount Device

You may choose to place your unit on a shelf or desktop (rubber feet included), or rack mount it using the supplied mounting brackets (EIA 19” rack mountable). The front panel should be visible and unobstructed so that the front panel buttons and LCD display are accessible. All connections are made to the rear of the chassis. The VelocityKVM Extender chassis does not need to be opened or accessed. The sturdy metal case allows units to be stacked as needed.

Mounting Bracket Removal

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 16

Cooling

The VelocityKVM Extender System uses two DC fans to move air horizontally through the enclosure.

Note: Be sure to leave a minimum of 2” ventilation space on both sides of the units,

especially if the units are being stacked.

Front Panel Display and Buttons

The front-panel LCD display should be visible and accessible for system setup. The front panel buttons are used to configure special video settings and to review existing VelocityKVM Extender configurations. More detailed information on the Front Panel can be found in the General Front Panel Usage section (Page 27).

VelocityKVM-24 Extender Front Panel LCD Display

Connecting the VelocityKVM Extender

Types of Connections

All physical connections to the product use industry-standard connectors. Non-supplied cables that may be needed are commercially available. All connections are found on the rear of the unit.

Fiber Cable

Fiber-optic cables run between the Transmitter unit (near your CPU) and the Receiver unit (near your desktop devices). The standard multi-mode fiber optic cables must be 50 or 62.5µm, terminated with LC, ST or SC- type fiber optic connectors. Single-mode fiber optic cables must be 9µm, UPC (Ultra Physical Contact), terminated with LC, ST or SC- type fiber optic connectors. Be careful not to kink or pinch the fiber optic cable as it is being installed and keep all bend radii to no less than 3 inches (76.2mm).

It is the standard VelocityKVM convention that fiber L1 carries data (PS2, USB, audio, serial, etc.) and video signal 1 (DVI or RGB) from the transmitter to the receiver. If a back channel is required, fiber L2 carries data from the receiver to the transmitter. If additional video channels are required, they are carried from transmitter to receiver via fibers L3, L4 and L5, depending on the extender model. (See page 53 for additional fiber configurations used with the Fail-Over option.)

Transmitter

The transmitter unit connects to the computer at the DVI In port using a DVI-D male-to-male cable (CBL000009-002MR for single-link and/or CBL000023-002MR for dual-link) which is supplied with the system. The connections to the VelocityKVM Extender Transmitters can be viewed in detail in the REAR PANEL VIEW section of this manual beginning on page 19.

Receiver

The receiver unit connects to a video monitor using a DVI-D male-to-male cable. Peripherals connect with their own standard cables. The connections to the VelocityKVM Extender Receivers can be viewed in detail in the REAR PANEL VIEW section of this manual.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 17

Receiver Serial Port

The Tx has a DB9F connector and is wired as a DCE (Data Communications Equipment) device. The Rx has a DB9M connector and is wired as a DTE (Data Terminal Equipment) device. The Tx

connects to the computer and the Rx connects to a touch screen, tablet, tape controller, etc., using a DB9 Male to DB9 Female Cable (CBL000017-006F is supplied in KIT-000005-R and is provided with the system). An RS422 option for controlling broadcast equipment is also available.

Stereo Emitter IN

Audio OUT ►

◄Audio IN

USB 2.0

USB HID

PS/2 Keyboard

PS/2 Mouse

The VelocityKVM-24W (DVI 2 Display, USB-HID, USB 2.0) Fiber Extension System

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 18

Rear Panel Views and Hardware Connections

Typically used Fiber and Copper Cables

Fiber Optic Cable (SC)

Fiber Optic Cable (ST)

Fiber Optic Cable (LC)

DVI to DVI

3.5mm AUDIO

USB (A & B)

Serial (RS232, RS422)

PS2

75Ω BNC

CAT5 (RJ45, Network Option)

VAC

Peripheral and Update Ports

The following Transmitter and Receiver rear panel diagrams denote the functions of the various peripheral device ports, including the FireWire option and its LED indicators, for all VelocityKVM Extenders. Refer to the Quick Start Guides in Appendix B for more information.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 19

VelocityKVM Transmitters and Receivers with the FireWire Option: Peripheral and Update Ports, LED Indicators

NOTE: The FireWire option requires 2 additional Fiber Optic Cables.

Audio IN (source)

FireWire (Fibers & IN Port)

FireWire Indicator LEDs

PWR: FireWire PCB power On/Off CP: ON=Cable Powered CLINK: ON=CPU connected (linked) FOL: (Fiber Optic Link) ON=connection, BLINKING=no connection

Unmarked LEDs are non-functioning

Audio OUT (speakers)

FireWire (Fibers & OUT Port)

FireWire Indicator LEDs

PWR: FireWire PCB power On/Off CP: ON=Cable Powered CLINK: ON=CPU connected (linked) FOL: (Fiber Optic Link) ON=connection, BLINKING=no connection

Unmarked LEDs are non-functioning

RS-232

Stereo Emitter IN (3D)

Audio OUT

(from microphone)

RS-232

USB HID & USB 2.0 IN

USB HID, PS2 and USB 2.0

Audio IN (microphone)

Stereo Emitter OUT (3D)

Local Keyboard/Mouse (HID or PS2)

PS2 Keyboard/Mouse (source)

Transmitter

VEL-F00M04-LCTX

Update Ports

Receiver

VEL-F00M04-LCRX

Fiber and Video Ports

The following transmitter and receiver rear panel diagrams explain the functions of the fiber optic cable input and output ports and the video input and output ports for each of the VelocityKVM Extenders. For the fiber connections, Optical Fiber L1, which carries both DATA from Tx to Rx and VIDEO, is in

purple, Optical Fiber L2, which carries DATA from Rx to Tx, is in blue and all VIDEO ONLY fibers

are in red. Refer to the Quick Start Guides in Appendix B (pg. 45-52) for more information.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 20

Velocity-5 KVM Multi-Mode Extender

Single-Head, Single-Link RGB/DVI

Transmitter VEL-W00M05-LCTX

Receiver VEL-W00M05-LCRX

L1 Fiber: Data Tx to Rx & Video

L2 Fiber: Data Rx to Tx

RGB/DVI OUT (local) RGB/DVI IN (from source)

L2 Fiber: Data Rx to Tx

L1 Fiber: Data Tx to Rx & Video

Velocity-8 KVM Multi-Mode Extender

Dual-Link DVI

Transmitter VEL-W00M08-LCTX

Receiver VEL-W00M08-LCRX

RGB/DVI OUT (Secondary) RGB/DVI OUT (DDC)

L1 Fiber: Data Tx to Rx & Video Primary

L2 Fiber: Data Rx to Tx

L3 Fiber: Video Secondary

Dual-Link DVI OUT (local) Dual-Link DVI IN (from source)

L2 Fiber: Data Rx to Tx

L1 Fiber: Data Tx to Rx & Video Primary

L3 Fiber: Video Secondary

Dual-Link DVI OUT (Secondary) Dual-Link DVI OUT (DDC)

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 21

Velocity-24 KVM Multi-Mode Extender

DVI 2 Display

Transmitter VEL-W00M24-LCTX

Receiver VEL-W00M24-LCRX

Velocity-28 KVM Multi-Mode Extender

Dual-Link, Single-Link DVI, 2 Display

Transmitter VEL-W00M28-LCTX

L1 Fiber: Data Tx to Rx & Video 1

L2 Fiber: Data Rx to Tx

L3 Fiber: Video 2

L2 Fiber: Data Rx to Tx

L1 Fiber: Data Tx to Rx & Video 1

L3 Fiber: Video 2

L1 Fiber: Data Tx to Rx & Video 1 Primary

L2 Fiber: Data Rx to Tx

L3 Fiber: Video 1 Secondary L4 Fiber: Video 2

DVI OUT 2 (local) DVI IN 2 (from source) DVI OUT 1 (local) DVI IN 1 (from source)

DVI OUT 2 (Secondary) DVI OUT 2 (DDC) DVI OUT 1 (Secondary) DVI OUT 1 (DDC)

Single-Link DVI OUT 2 (local) Single-Link DVI IN 2 (from source) Dual-Link DVI OUT 1 (local) Dual-Link DVI IN 1 (from source)

L2 Fiber: Data Rx to Tx

L1 Fiber: Data Tx to Rx & Video 1 Primary

L4 Fiber: Video 2

Receiver VEL-W00M28-LCRX

L3 Fiber: Video 1 Secondary

Single-Link DVI OUT 2 Dual-Link DVI OUT 1

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 22

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 23

Velocity-38 KVM Multi-Mode Extender

2 Dual-Link DVI Displays

Transmitter VEL-W00M38-LCTX

Receiver VEL-W00M38-LCRX

L1 Fiber: Data Tx to Rx & Video 1 Primary

L2 Fiber: Data Rx to Tx

L3 Fiber: Video 1 Secondary L4 Fiber: Video 2 Primary L5 Fiber: Video 2 Secondary

Dual-Link DVI OUT 2 (local) Dual-Link DVI IN 2 (from source) Dual-Link DVI OUT 1 (local) Dual-Link DVI IN 1 (from source)

L2 Fiber: Data Rx to Tx

L1 Fiber: Data Tx to Rx & Video 1 Primary

L4 Fiber: Video 2 Primary L3 Fiber: Video 1 Secondary L5 Fiber: Video 2 Secondary

Dual-Link DVI OUT 2 Dual-Link DVI OUT 1

Cables

Peripheral Cables:

KIT-000005-R Audio Cable Kit (8 pcs.)– Qty 1, all models

2 each – USB A-B (6’) 2 each – 3.5mm to 3.5mm plug (6’) 1 each – DB9M to DB9F (6’) 1 each – BNC male to male, 75Ω (6’)

2 each – 6 pin mini din (6’)

KIT-5 Cables (Included)

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 24

Video Cables

Depending on the VelocityKVM Extender model, use the following video cables:

Single-link: DVI-D Male Cable, 2 Meters (CBL000009-002MR) Single-link: DVI-I Male Cable, 2 Meters (CBL000013-002MR) RGB: HD15 to DVI-A Male Cable, 2 Meters (CBL000022-002MR) - VelocityKVM-5, Qty 1 Dual-link: DVI-D Male Cable, 2 Meters (CBL000023-002MR)

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 25

Installation

All physical connections to the product use industry-standard connectors. Non-supplied cables are commercially available. All connections are found on the rear of the unit. Refer to the Quick Start

Guides in Appendix B (pg. 45-52) for more information.

Set-Up

Firmware Upgrades

Firmware upgrades are available through Thinklogical. Please call for assistance: 1-203-647-8700.

Front Panel Usage

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 26

General Front Panel Usage

*System

Thinkl

ogical

Once the system is powered up, the initial Transmitter display is shown as follows:

Velocity Tx VXX.XX

The company name is listed on the first line of the display. The model and software version (VXX.XX) of the unit is displayed on the second line.

By pressing the down arrow the VelocityKVM Extender allows you to enter into the main menu.

The main root menu items are displayed with an *. They are as follows:

*DDC

Once a *root menu item is displayed, you can then use the left arrow or right arrow to review settings or make changes, if allowed.

SFP LOS and SFP Des OK Signal

In the *System root menu, scrolling right or left will bring you to the SFP Loss of Signal and SFP Des OK Signal menus.

The SFP Loss of Signal menu provides confirmation of lost or unused video signals at the Receiver and of lost or unused data-return signals at the Transmitter. A lost/unused signal will be indicated by a 1 at SFPs 1 through 4 on a Receiver and by a 1 at SFP 1 on a Transmitter. If only 2 SFPs are in use, as in a VelocityKVM-24 Receiver, SFPs 3 and 4 will always indicate that no signal is present (1).

The SFP Des OK Signal menu provides confirmation that a good deserializer signal is detected at the Receiver and Transmitter SFPs. A good signal will be indicated by a 1 at SFPs 1 through 4. If only 2 SFPs are in use, as in a VelocityKVM-24, SFPs 3 and 4 will always indicate that no signal is present (1).

Fiber L1 on the Transmitter and L2 on the Receiver are always transmitting. The SFPs connected to fibers L3, L4 and L5 will not transmit until a video signal is applied to the Transmitter’s DVI IN connector.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 27

The following table shows the expected SFP Loss of Signal and Des OK Signal indications for each model of a properly connected VelocityKVM Receiver and Transmitter:

TABLE 4: SFP Loss Of Signal and SFP Des OK Signal LCD Indicators

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 28

The VelocityKVM Extender menu functionality is as follows

(Some menu options may not be available on all models.):

TRANSMITTER:

Display Modifiable Description *System

LS Connected NO Indicates fiber status from TX to RX. (0=connected) Tx Ctrl Name TX Only Name entered on TX unit is displayed on RX unit. Load Defaults YES Loads factory default video configurations. Store Values YES Store video configurations. KM Device NO Revision of the VelocityKVM portion that plugs into CPU. KM Remote Host NO Revision of the VelocityVKM Host on the RX unit. KM Local Host NO Revision of the VelocityVKM Host on the TX unit. TX Control NO Revision of the TX unit laser and front panel control. RX Control NO Revision of the RX unit laser and front panel control. FPGA Version NO Revision of the FPGA used for video generation. Serial Number NO 2 digits: week, 2 digits: year, 2 to 4 digits unique unit number Debug Values YES Factory Use. Allow FPGA Update YES Select YES to enable update Aud/USB Reset En YES Enable/disable USB 1.1 reset, lost Tx/Rx link Des OK NO 1=Yes 0=No SFP Loss of Signal NO Indicates loss of SFP signal. (1= not connected) Temp in Celsius NO Tb=PCB temp (max=70) Tf=FPGA temp (max=85) KMASS Card ID NO 0E = original, OC=SoDimm Video Card ID NO 08=single 09=dual head 0A=dual link 0B=RGB USB 2.0 Card ID NO 08=original 09=SoDimm

*DDC

DDC PROM Emula. Mode YES Options are Dynamic, Static and Passthru. In Dynamic mode, the EDID table* of the monitor connected to the

RX is read and stored on the TX. After any change in monitor type a new EDID table will be stored on the TX. An EDID table is always presented to the video source, whether the TX is ON or OFF.

Static mode is used to maintain the current EDID table regardless

of monitor changes at the RX. An EDID table is always presented to the video source, whether the TX is ON or OFF.

Passthru mode makes the DDC pins look like direct connection

between the TX and RX, allowing the computer to talk directly to the monitor.

Load Default DDC YES Loads the default EDID table* into the TX which allows 1024x768

and 1920x1200. This puts the TX into static mode.

Load 1080p YES Loads a widescreen version of the EDID table* into the TX.

Supported resolutions include 1920x1080 and 1280x720.

Acquire DDC YES Gets the EDID table* of the attached display, stores the information

on the TX, and puts the TX in static mode.

Force DDC Mode YES Used to force a monitor to appear as either digital or analog.

Since the Velocity products can convert between analog and digital, sometimes the EDID table* has to be modified to match the method of connecting the TX to CPU.

*See EDID Definitions and DDC Modes in Appendix F, page 60

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 29

Velocity 5 Video Front Panel Menu TRANSMITTER

Display Modifiable Description * Video

VGA Connected NO An indication of whether VGA video is input to the Vis TX Resolution input NO Active pixels x active lines vertical rate Hor. Freq NO Horizontal frequency Auto Phase YES Automatically adjusts the Sampling Phase to the best setting PLL Total YES Total pixels, one line. (Horiz. active pixels + Horiz. blanking pixels) HSOUT Width YES Horizontal sync (Hsync) of video, measured in pixels DE Start YES Horizontal back porch (Hpb) of video, measured in pixels DE Width YES Total active pixels in one line Line Start YES Vertical back porch (Vbp) + Vertical sync (Vsync) of video,

measured in lines Line Width YES The number of visible lines in one frame Hsync Period NO Used to determine analog video horizontal frequency.

Use the following formula to calculate the frequency:

(25x10E6 x 16) / Hsync Period = Horizontal Frequency

Vsync Period NO Total lines in one frame of video = active lines + blanking lines ISL Sync Status NO Thinklogical support use only. Measures sync selection and ………

sync polarity

ISL Sync Activity NO Thinklogical support use only. Measures sync activity Video 1 cnt. NO Thinklogical support use only. Video IN pixel clock (in hex) ___________________________________________________________________________

RECEIVER:

*System

LS Connected NO Indicates fiber status from TX to RX (0=connected) Tx Ctrl Name TX Only Name entered on TX unit is displayed on RX unit. KM Device NO Revision of the VelocityKVM portion that plugs into CPU. KM Remote Host NO Revision of the VelocityVKM Host on the RX unit. KM Local Host NO Revision of the VelocityVKM Host on the TX unit. TX Control NO Revision of the TX unit laser and front panel control. RX Control NO Revision of the RX unit laser and front panel control. FPGA Version NO Revision of the FPGA used for video generation. Serial Number NO 2 digits: week, 2 digits: year, 2 to 4 digits unique unit number Debug Values YES Factory Use. Allow FPGA Update YES Select YES to enable update SFP Loss of Signal NO Indicates loss of SFP signal. (1=not connected) SFP Des OK Signal NO 1=Yes 0=No LS FPGA Ver. NO LS Data communication FPGA Vid1. FPGA Rev. NO Video FPGA for Head 1 Vid1. FPGA Type NO Video FPGA for Head 2 Temp in Celsius NO Tb=PCB temp (max=70) Tf=FPGA temp (max=85) KMASS Card ID NO 0E=original, OA= SoDimm KMASS FPGA Rev. NO FPGA used for LS/USB 2.0 Card KMASS Device ID NO Hardware ID of KMASS Card Video Card ID NO Hardware ID of Video Card

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 30

Display Modifiable Description

Aux. Card ID NO Hardware ID of Auxiliary Card Aux. Card FPGA Rev. NO FPGA Rev. of Auxiliary Card Original KMASS YES Option to use previous Interface revisions Allow Out Of Band YES Allows On-screen Display when used with Routers* Alt. HOT Key YES Used to modify Out Of Band Hot Key

*Contact Thinklogical before using this feature as it may impact the fiber channel.

*DDC

DDC PROM Emula. Mode YES Options are Dynamic, Static and Passthru. In Dynamic mode, the EDID table* of the monitor connected to the

RX is read and stored on the TX. After any change in monitor type a new EDID table will be stored on the TX. An EDID table is always presented to the video source, whether the TX is ON or OFF.

Static mode is used to maintain the current EDID table regardless

of monitor changes at the RX. An EDID table is always presented to the video source, whether the TX is ON or OFF.

Passthru mode makes the DDC pins look like direct connection

between the TX and RX, allowing the computer to talk directly to the monitor.

Load Default DDC YES Loads the default EDID table* into the TX which allows 1024x768

and 1920x1200. This puts the TX into static mode.

Load 1080p YES Loads a widescreen version of the EDID table* into the TX.

Supported resolutions include 1920x1080 and 1280x720.

Acquire DDC YES Gets the EDID table* of the attached display, stores the information

on the TX, and puts the TX in static mode.

Force DDC Mode YES Used to force a monitor to appear as either digital or analog.

Since the Velocity products can convert between analog and digital, sometimes the EDID table* has to be modified to match the method of connecting the TX to CPU.

*Video

VGA Connected NO An indication of whether VGA video is input to the Vis TX Resolution NO Active pixels x active lines vertical rate Hor. Freq NO Horizontal frequency Auto Phase YES Automatically adjust the Sampling Phase to the best setting PLL Total YES Total pixels, one line. (Horiz. active pixels + Horiz. blanking pixels) HSOut Width YES Horizontal sync (Hsync) of video, measured in pixels DE Start YES Horizontal back porch (Hpb) of video, measured in pixels DE Width YES Total active pixels in one line Line Start YES Vert. back porch (Vbp) + Vert. sync (Vsync) measured in lines Line Width YES The number of visible lines Hsync Period NO Used to determine analog video horizontal frequency.

Use the following formula to calculate the frequency:

(25x10E6 x 16) / Hsync Period = Horizontal Frequency

Vsync Period NO Total lines in one video frame = active lines + blanking lines ISL Sync Status NO Thinklogical support use only. Measures sync selection & polarity ISL Sync Activity NO Thinklogical support use only. Measures sync activity Video RX 1 cnt. NO Thinklogical support use only. Video IN 1 pixel clock (in hex)

*See EDID Definitions and DDC Modes in Appendix F, page 60

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 31

Thinkl

ogical

Store Values

Thinkl

ogical

Store Values

Saving Changes

Save analog video configurations so that following power up, the device can recall custom video settings.

Velocity Tx VXX.XX

Using the down arrow, scroll down to *System as shown below.

*System

Using the right arrow, scroll right until Store Values is displayed as shown below, then press enter.

Yes/No.= No

Using the up arrow or down arrow scroll until Yes appears as shown below. Then press enter.

Yes/No.= Yes

Using the right arrow or left arrow scroll until you return to the *System menu option. Using up arrow or down arrow, scroll until you get to the Thinklogical screen as shown below.

Velocity Tx VXX.XX

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 32

Restoring Factory Defaults

Thinkl

ogical

*System

Load Defaults

Load the factory default video configurations.

Velocity Tx VXX.XX

Using the down arrow, scroll down to *System (below).

Using the right arrow button, scroll right until Load Defaults is displayed (below), then press enter.

Yes/No= No

Using the up arrow or down arrow, scroll until Yes appears (below), then press enter.

Yes/No= Yes

Follow the steps below to save your changes:

Using the down arrow, scroll down to *System. Using the right arrow, scroll right until Store Values is displayed, then press enter. Using the up or down arrow, scroll until Yes appears, then press enter. Using the right or left arrow, scroll to return to the *System menu option. Using up or down arrow, scroll until you get to the Thinklogical screen.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 33

Naming the Transmitter Unit

Thinkl

ogical

*System

Tx Ctrl

TX Ctrl

Tx Ctrl

Modify the name of the unit through the Transmitter. The name entered on the Transmitter will display on the Receiver unit.

Using the arrow down button, scroll down to *System as shown below.

Velocity Tx VXX.XX

Using the right arrow, scroll right until Tx Ctrl is displayed (below), then press enter.

Name= TxUnit01

Using the right or left arrow, scroll until the blinking cursor is under the letter/number you want to change.

Name= TxUnit01

Using the up or down arrow, scroll (holding down the up or down arrow will scroll faster) until you find the appropriate letter/number, then press enter.

Name= TxUnit11

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 34

*System

Using the right or left arrow, scroll to return to the *System menu option.

Follow these steps to save your changes:

Regulatory & Safety Compliance

Safety Requirements

Symbols Found on Our Product

Markings and labels on the product follow industry-standard conventions. Regulatory markings found on the products comply with domestic and many international requirements.

Regulatory Compliance

The Thinklogical VelocityKVM Extender® products are designed and made in the U.S.A. VelocityKVM Extender® products have been tested by a certified testing laboratory and found to be compliant with the following standards (both domestic USA and many international locations):

North America

Safety

ANSI/UL60950-1: 1st Edition (2003) CAN/CSA C22.2 No. 60950-1-03

LASER Safety

CDRH 21CFR 1040.10 Class 1 LASER Product

Electromagnetic Interference

FCC CFR47, Part 15, Class A Industry Canada ICES-003 Issue 2, Revision 1

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 35

Australia & New Zealand

This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

European Union

Declaration of Conformity

Manufacturer’s Name & Address: Thinklogical

LLC 100 Washington Street Milford, Connecticut 06460 USA Telephone 1-203-647-8700

These products comply with the requirements of the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC.

Standards with Which Our Products Comply

Safety

CENELEC EN 60950-1, 1st Edition (2001)

LASER Safety

IEC60825:2001 Parts 1 and 2 Class 1 LASER Product

Electromagnetic Emissions

EN55022: 1994 (IEC/CSPIR22: 1993) EN61000-3-2/A14: 2000 EN61000-3-3: 1994

Electromagnetic Immunity

EN55024: 1998 Information Technology Equipment-Immunity Characteristics EN61000-4-2: 1995 Electro-Static Discharge Test EN61000-4-3: 1996 Radiated Immunity Field Test EN61000-4-4: 1995 Electrical Fast Transient Test EN61000-4-5: 1995 Power Supply Surge Test EN61000-4-6: 1996 Conducted Immunity Test EN61000-4-8: 1993 Magnetic Field Test EN61000-4-11: 1994 Voltage Dips & Interrupts Test

Supplementary Information

The following statements may be appropriate for certain geographical regions and might not apply to your location.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 36

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigencies du Règlement sur le matérial brouilleur du Canada.

Warning! This is a Class A product. In a domestic environment, this product may cause

radio interference, in which case the user may be required to take corrective measures.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications in which case the user may be required to take adequate corrective measures at their own expense.

Note: This Class A digital apparatus complies with Canadian ICES-003 and has been verified as being compliant within the Class A limits of the FCC Radio Frequency Device Rules (FCC Title 47, Part 15, Subpart B CLASS A), measured to CISPR 22: 1993 limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment.

Note: magnetic fields

Note: may be needed to comply with Immunity Requirements

The user may notice degraded audio performance in the presence of electro-

If using a keyboard that is noise susceptible, a ferrite ring on the keyboard cable

Product Serial Number

Thinklogical® products have a unique serial number printed on an adhesive label that is fixed, typically, to the underside of the unit. The serial number includes a date-code formatted as 2 digits for the week and 2 digits for the year, plus two to four digits for a unique unit number.

Example: Serial number 2813124 indicates that the unit was built in the 28th week of the year 2013 and is unit number 124.

Connection to Our Products

Connections and installation hardware for our products use industry-standard devices and methods. All wiring connections to the customer equipment are designed to minimize proprietary or customized connectors and cabling. Power connections are made with regionally appropriate power cords and approved methods.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 37

How to Contact Us

Customer Support

Thinklogical is an engineering company and you will receive the assistance you require directly from our most knowledgeable engineers. We believe that the first line of support is the design engineer that developed each particular product. Therefore your needs will be handled promptly by our in-house engineers who are most familiar with your products.

Website

Check out our website for current product offerings, support information and general information about all of the products we offer.

Our internet website offers product information on all current systems, including technical specification sheets and installation guides (for viewing online or for download), product diagrams showing physical connections and other information you might need.

Internet: www.thinklogical.com

Note: Most online documents are stored as Adobe Acrobat “PDF” files. If you do not have the Adobe Acrobat reader needed to view PDF files, visit www.adobe.com for a download.

Thinklogical is staffed Monday through Friday from 8:30am to 5:00pm, Eastern Time Zone. We will do our best to respond to your emails promptly. Please use one of the following email addresses for your particular needs:

info@thinklogical.com – Information on Thinklogical and our products. sales@thinklogical.com – Sales Department - orders, questions or issues. support@thinklogical.com – Product support, technical issues or questions, product

repairs and request for Return Authorization.

Telephone

Product & Customer Support: 1-203-647-8700 US Commercial & Canada Sales: 1-203-647-8769

US Federal Government Sales: 1-203-647-8716 Toll Free in the Continental US: 1-800-291-3211 International Sales (Europe, Middle East, Africa): 1-203-647-8704

International Sales (Asia Pacific, Central & Latin America): 1-203-647-8734 Fax: 1-203-783-9949

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 38

Please contact our expert sales staff in Milford, CT. We are here Monday through Friday from 8:30am to 5:00pm, Eastern Time Zone. We’ll provide a representative’s direct dial phone number when you call.

If leaving a voice message, please provide a preferred time to call back so we may reach you at your convenience.

Our switchboard attendant will direct your call during regular business hours. We have an automated attendant answering our main telephone switchboard after regular business hours and holidays. You can leave voice messages for individuals at any time.

Fax

Our company facsimile number is 1-203-783-9949. Please indicate the nature of the fax on your cover sheet and provide return contact information.

Product Support

Thinklogical’s support personnel are available Monday through Friday from 8:30am to 5:00pm, Eastern Time Zone. If your application requires assistance at some time outside of our normal business hours, please contact us beforehand and we will do our best to make arrangements to help you with your Thinklogical products.

Limited Warranty Information

Thinklogical, LLC (“Thinklogical”) warrants this product against defects in materials and workmanship for a period of one (1) year from the date of delivery (ordinary wear and tear excluded). This limited warranty does not cover defects resulting from (i) use of the product other than as described in the applicable documentation for the product; (ii) modifications to or repairs of the product that are made by any party other than Thinklogical or a party acting on Thinklogical’s behalf, or (iii) combination of the product with third party products that is not consented to by Thinklogical. Occurrences of events described in (i) – (iii) shall void the foregoing warranty. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Except for the express warranty set forth above, to the fullest extent permitted under applicable law, Thinklogical, LLC and its suppliers disclaim any and all other warranties, express and implied, including without limitation the implied warranties of merchantability, fitness for a particular purpose, title and non-infringement.

If the defective product is returned to the authorized dealer within one (1) year of the delivery date, repair or replacement of the product will be made. Repairs may be made with refurbished parts. If repair or replacement is not possible, Thinklogical may keep the defective product and refund the amount that you paid for the defective product. These are Thinklogical’s sole obligations, and your exclusive remedies, for a breach of the limited warranty set forth above.

To return a defective product, contact the Thinklogical authorized dealer from whom you purchased the product. Do not return a product directly to Thinklogical without prior authorization from your dealer.

If you have received prior authorization from your dealer and are returning a product directly to Thinklogical:

1. You may contact your Sales Representative directly or call Customer Support at 1-203-647-8700 or 1-800-291-3211 (toll free).

2. Describe the defect with the product and Customer Support will issue a Return Merchandise Authorization Number (RMA#).

3. Pack the product in all of its original packing, if possible, and write the RMA number on the box.

4. Return the product to: Thinklogical, LLC

Attn: RMA# [Insert the issued RMA# here.] 100 Washington Street Milford, CT 06460 USA

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 39

If you have any issue with a product, have product questions or need technical assistance with your Thinklogical system, please call us at 1-800-291-3211 (USA only) or 1-203-647-8700 and let us help.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 40

Appendix A

In the following part number examples, the inclusion of the USB 2.0 option is shown. (This is the U immediately following the VEL-). If no option is included, the U will be replaced by a 0. For the FireWire option, this will be an F and for the HID option, it will be a leading H. See page 44 for more information on part numbering.

Thinklogical's Full Line of Velocitykvm and Video Multi-Mode Fiber

Extenders

Part Number

VEL-W00M04-LCRX

VEL-W00M04-LCTX

VEL-W00M04-SCRX

VEL-W00M04-SCTX

VEL-W00M04-STRX

VEL-W00M04-STTX

VEL-W00M05-LCRX

VEL-W00M05-LCTX

VEL-W00M05-SCRX

VEL-W00M05-SCTX

VEL-W00M05-STRX

Description

VelocityKVM-4 Multi-Mode Fiber Extenders

Velocity KVM Extender Receiver, Single Head Single Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Single Head Single Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Single Head Single Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Single Head Single Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Single Head Single Link DVI, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Single Head Single Link DVI, USB 2.0, KMAS, Multi-mode, ST

VelocityKVM-5 Multi-Mode Fiber Extenders

Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, USB2.0, KMAS, Multi-mode, LC Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, USB2.0, KMAS, Multi-mode, SC Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, USB 2.0, KMAS, Multi-mode, ST

VEL-W00M05-STTX

VEL-W00M08-LCRX

VEL-W00M08-LCTX

VEL-W00M08-SCRX

VEL-W00M08-SCTX

VEL-W00M08-STRX

VEL-W00M08-STTX

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 41

Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, USB2.0, KMAS, Multi-mode, ST

VelocityKVM-8 Multi-Mode Fiber Extenders

Velocity KVM Extender Receiver, Single Head Dual Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Single Head Dual Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Single Head Dual Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Single Head Dual Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Single Head Dual Link DVI, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Single Head Dual Link DVI, USB 2.0, KMAS, Multi-mode, ST

Part Number

VelocityKVM-24 Multi-Mode Fiber Extenders

VEL-W00M24-LCRX

VEL-W00M24-LCTX

VEL-W00M24-SCRX

VEL-W00M24-SCTX

VEL-W00M24-STRX

VEL-W00M24-STTX

VEL-W00M28-LCRX

VEL-W00M28-LCTX

VEL-W00M28-SCRX

VEL-W00M28-SCTX

VEL-W00M28-STRX

VEL-W00M28-STTX

VEL-W00M34-LCRX

Velocity KVM Extender Receiver, Dual Head Single Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Dual Head Single Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Dual Head Single Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Dual Head Single Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Dual Head Single Link DVI, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Dual Head Single Link DVI, USB 2.0, KMAS, Multi-mode, ST

VelocityKVM-28 Multi-Mode Fiber Extenders

Velocity KVM Extender Receiver, Dual Link, Single Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, Dual Link, Single Link DVI, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, Dual Link, Single Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, Dual Link, Single Link DVI, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, Dual Link, Single Link DVI, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, Dual Link, Single Link DVI, USB 2.0, KMAS, Multi-mode, ST

VelocityKVM-34 Multi-Mode Fiber Extenders

Velocity KVM Extender Receiver, DVI Four Display, USB 2.0, KMAS, Multi-mode, LC

VEL-W00M34-LCTX

VEL-W00M34-SCRX

VEL-W00M34-SCTX

VEL-W00M34-STRX

VEL-W00M34-STTX

VEL-W00M35-LCRX

VEL-W00M35-LCTX

VEL-W00M35-SCRX

VEL-W00M35-SCTX

VEL-W00M35-STRX

VEL-W00M35-STTX

VEL-W00M38-LCRX

VEL-W00M38-LCTX

Velocity KVM Extender Transmitter, DVI Four Display, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, DVI Four Display, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, DVI Four Display, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, DVI Four Display, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, DVI Four Display, USB 2.0, KMAS, Multi-mode, ST

VelocityKVM-35 Multi-Mode Fiber Extenders

Velocity KVM Extender Receiver, DVI Three Display, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, DVI Three Display, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Receiver, DVI Three Display, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, DVI Three Display, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, DVI Three Display, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, DVI Three Display, USB 2.0, KMAS, Multi-mode, ST

VelocityKVM-38 Multi-Mode Fiber Extenders

Velocity KVM Extender Receiver, DVI two Dual-link Display, USB 2.0, KMAS, Multi-mode, LC Velocity KVM Extender Transmitter, DVI two Dual-link Display, USB 2.0, KMAS, Multi-mode, LC

VEL-W00M38-SCRX

VEL-W00M38-SCTX

VEL-W00M38-STRX

VEL-W00M38-STTX

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 42

Velocity KVM Extender Receiver, DVI two Dual-link Display, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Transmitter, DVI two Dual-link Display, USB 2.0, KMAS, Multi-mode, SC Velocity KVM Extender Receiver, DVI two Dual-link Display, USB 2.0, KMAS, Multi-mode, ST Velocity KVM Extender Transmitter, DVI two Dual-link Display, USB 2.0, KMAS, Multi-mode, ST

Thinklogical's Full Line of Velocitykvm and Video Single-Mode Fiber

Extenders

Part Number

VEL-W00S04-SCRX VEL-W00S04-SCTX

VEL-W00S05-SCRX VEL-W00S05-SCTX

VEL-W00S08-SCRX VEL-W00S08-SCTX

VEL-W00S24-SCRX

VelocityKVM-4 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, Single Head Single Link DVI, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, Single Head Single Link DVI, USB 2.0, KMAS, Single-mode, SC/APC

VelocityKVM-5 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, Single Head Dual Link DVI/RGB, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, Single Head Dual Link DVI/RGB, USB2.0, KMAS, Single-mode, SC/APC

VelocityKVM-8 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, Single Head Dual Link DVI, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, Single Head Dual Link DVI, USB 2.0, KMAS, Single-mode, SC/APC

VelocityKVM-24 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, Dual Head Single Link DVI, USB 2.0, KMAS, Single-mode, SC/APC

Description

VEL-W00S24-SCTX

Part Number

VEL-W00S28-SCRX VEL-W00S28-SCTX

VEL-W00S34-SCRX VEL-W00S34-SCTX

VEL-W00S35-SCRX VEL-W00S35-SCTX

VEL-W00S38-SCRX VEL-W00S38-SCTX

Velocity KVM Extender Tx, Dual Head Single Link DVI, USB 2.0, KMAS, Single-mode, SC/APC

VelocityKVM-28 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, Dual Link, Single Link DVI, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, Dual Link, Single Link DVI, USB 2.0, KMAS, Single-mode, SC/APC

Velocity KVM-34 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, 4 Display DVI, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, 4 Display DVI, USB 2.0, KMAS, Single-mode, SC/APC

VelocityKVM-35 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, 3 Display DVI, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, 3 Display DVI, USB 2.0, KMAS, Single-mode, SC/APC

VelocityKVM-38 Single-Mode Fiber Extenders

Velocity KVM Extender Rx, Two Dual-link DVI Display, USB 2.0, KMAS, Single-mode, SC/APC Velocity KVM Extender Tx, Two Dual-link DVI Display, USB 2.0, KMAS, Single-mode, SC/APC

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 43

VEL-XXXXXX-XXXX

VEL= Velocity VEA = Velocity with Separate Audio

Part Number Reference

Velocity KVM Extenders

000= USB 1.1 00D= USB 1.1 with Separate Data Path 0R0= USB 1.1 with Redundant Fiber Path 0RD= USB 1.1 with Redundant Fiber Path and Separate Data Path A00= Professional Audio, HID, No USB 1.1 or USB 2.0 A0D= Professional Audio, HID, No USB 1.1 or USB 2.0 with Separate Data Path AR0= Professional Audio, HID, No USB 1.1 or USB 2.0, Redundant Fiber Path ARD= Professional Audio, HID, No USB 1.1 or USB 2.0, Redundant, Separate Data Path E00= Firewire with USB 2.0, No USB 1.1 E0D= Firewire with USB 2.0 with Separate Data Path, No USB 1.1 F00= Firewire with USB 1.1H00= HID HOD= HID with Separate Data Path HR0= HID, Redundant HRD= HID, Redundant, Separate Data Path K00= Network with USB 2.0, HID K0D= Network with USB 2.0, HID, Separate Data Path KR0= Network with USB 2.0, HID, Redundant Fiber Path KRD= Network with USB 2.0, HID, Separate Data Path, Redundant Fiber Path N00= Network, USB 1.1 N0D= Network with Separate Data Path, USB 1.1, HID P00= Professional Audio, HID with USB 2.0, no USB 1.1 P0D= Professional Audio, HID with USB 2.0, no USB 1.1, Separate Data Path PR0= Professional Audio, HID with USB 2.0, no USB 1.1, Redundant Fiber Path PRD= Professional Audio, HID with USB 2.0, no USB 1.1, Redundant, Separate Data Path U00= USB 2.0 U0D= USB 2.0 with Separate Data Path UR0= USB 2.0 with Redundant Fiber Path W00= HID with USB 2.0, No USB 1.1 WR0= HID with USB 2.0 with Redundant Fiber Path, No USB 1.1 W0D= HID with USB 2.0 with Separate Data Path, No USB 1.1 WRD= HID with USB 2.0 with Redundant Fiber Path and Separate Data Path, No USB 1.1 W00= Multipath, HID with USB 2.0, No USB 1.1 W0D= Multipath, HID with USB 2.0 with Separate Data Path, No USB 1.1 WRD= Multipath, HID with USB 2.0 with Redundant Fiber Path and Separate Data Path, No USB 1.1 Z00= Multipath, Professional Audio, HID with USB 2.0, No USB 1.1 ZR0= Multipath, Professional Audio, HID with USB 2.0 with Redundant Fiber Path, No USB 1.1 Z0D= Multipath, Professional Audio, HID with USB 2.0 with Separate Data Path, No USB 1.1 ZRD= Multipath, Professional Audio, HID with USB 2.0 with Redundant Fiber Path and Separate Data Path, No USB 1.1

TX= Transmitter RX= Receiver

ST Connector SC Connector LC Connector NK Connector

03= 1 SL DVI 06= 1 DL DVI 09= 1 RGB 10= 1 RGB/DVI 12= 1 RGB HV, Component Video

M= Multi-Mode S= Single-Mode X= Multi-Path

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 44

Appendix B- Quick Start Guides

A.B.1 VelocityKVM-4 Quick Start Guide

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 45

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4

STEP 5: If desired, connect your optional

local keyboard & mouse by inserting the PS/2

Velocitykvm-5

Multi-Mode Fiber Extension System – Single Head, Single Link RGB/DVI

QUICK START GUIDE

Local RGB

OUT

/DVI

or USB HID connectors into the VelocityKVM Transmitter’s local devices receptacles and

connect the optional local RGB/DVI display to the Transmitter’s RGB/DVI OUT Port. Ensure all system functions are operating properly.

USB HID or PS2

Keyboard/Mouse

A.B.2 VelocityKVM-5 Quick Start Guide

Source CP

Local Audio

OUT

STEP 1: Connect your Multi-Mode Fiber

Optic Cables between the Transmitter and Receiver units (up to 1000 meters) as shown.

RGB/DVI I

L1: Data Tx to Rx and Video

L2: Data Rx to Tx

Stere

Stereo Emitter IN

◄

Audio I

Audio OUT ►

PS/2 Keyboard PS/2

Mouse

USB HID (

USB HID or PS2

Keyboard/Mouse

USB 2.0

ybd/Mouse

)

STEP 2: Ensure that

the POWER ON/OFF

switch is in the OFF

position (0) on both

the Tx and Rx units.

Connect the supplied

AC Power Cords to both units and plug

each into a standard

AC supply. Turn both

switches ON (1).

USB 2.0

OUT

DDC

GB/DVI OU

Audio IN/OU

STEP 3: Connect the destination RGB/DVI and KVM

devices to the VelocityKVM Receiver using RGB/ DVI cables and standard copper cables. Ensure the devices are turned ON.

RGB/DVI

VELOCITY-5W_Manual_QSG_Rev_A

Page 46

A.B.3 VelocityKVM-8 Quick Start Guide

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 47

A.B.4 VelocityKVM-24 Quick Start Guide

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 48

A.B.5 VelocityKVM-28 Quick Start Guide

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 49

USB 2.0

USB HID (Kybd/Mouse)

PS/2 Keyboard

PS/2 Mouse

Audio OUT ►

◄ Audio IN

Stereo Emitter IN

A.B.6 VelocityKVM-34 Quick Start Guide

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 50

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4

Velocitykvm-35

Multi-Mode Fiber Extension System – Three DVI Displays

QUICK START GUIDE

USB HID or PS2 Keyboard/Mouse

A.B.7 VelocityKVM-35 Quick Start Guide

Fiber-Optic Cables:

L1: Data Tx to Rx and Video 1

Source CP

L2: Data Rx to Tx

L3: Video 2 L4: Video 3

Local Audio OUT

STEP 1: Connect the 4 Multi-Mode Fiber-Optic Cables

between the Transmitter and Receiver units (up to 1000 meters) as shown.

STEP 2: * STEP 3: Connect the destination DVI and KVM devices to

the Ve locityKVM Receiver u sing standard cables. Ensure the devices are turned ON.

STEP 4: Connect the DVI and KVM cables between the

Source CPU and the VelocityKVM Transmitter using the cables supplied in KIT-000005-R. Ensure the CPU i s turned ON.

STEP 5: If desired, connect your optional local keyboard &

mouse by inserting the PS/2 or USB HID connectors into the VelocityKVM Transmitter’s local devices receptacles.

Ensure all system functions are operating properly.

Page 51

VI IN 2

DVI IN

I IN

eo Emitter IN

Ste

Stereo 3-

DVI O

Audio

◄IN

Audio OUT ►

PS/2 Keyboard

use

PS/2 Mo

USB HID

USB 2.0

(Kybd/Mouse)

Audio IN/OU

USB HID or PS2 Keyboard/Mouse

*STEP 2: Ensure that the POWER ON/OFF

switch is in the OFF

position (0) on both the

Tx and Rx units.

Connect the supplied

AC Power Cords to both units and plug

each into a standard

AC supply. Turn both

switches ON (1).

USB 2.0

Velocity-35W_Manual_QSG_ Rev_A

A.B.8 VelocityKVM-38 Quick Start Guide

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 52

Appendix C- Automatic Fail-Over Option

For applications in need of an Auto Fail-Over system, Thinklogical offers a solution to meet this need in each of our VelocityKVM models. This option features two separate fiber paths for each signal and the ability to select which of the two paths is the viable path.

The Transmitter and Receiver contain all the same features as the standard VelocityKVM products in addition to offering a redundant fiber connector (L1’, L2’, etc.) for each standard fiber connector (L1, L2, etc.). All other features function as in our standard VelocityKVM Extenders.

Example:

VelocityKVM-24WR Transmitter with Automatic Fail-Over

Fiber Connections

L1 and L1' are redundant outputs, transmitting the same video and KMASS data; L3 and L3' are redundant outputs, transmitting the same video data. The same will apply to any additional video fibers (L4, L4’, L5, L5’, etc.) used in other models.

L2 and L2' are redundant back channel KMASS data inputs. There is an internal MUX which selects L2 or L2' data. When the unit is powered on, it will select L2 first (if L2 is active); otherwise, it will select L2' (if L2' is active). It will only switch from L2 to L2' if L2 is inactive and L2' is active. Likewise, it will only switch from L2' to L2 if L2' is inactive and L2 is active.

VelocityKVM-24WR Transmitter (VEL-WR0M24-LCTX)

VelocityKVM-24WR Receiver with Automatic Fail-Over

Fiber Connections

L1 and L1' are redundant video and KMASS data inputs. There is an internal MUX which selects L1 or L1'. When the unit is powered on, it will select L1 first (if L1 is active); otherwise, it will select L1' (if L1' is active). It will only switch from L1 to L1' if L1 is inactive and L1' is active. Likewise, it will only switch from L1' to L1 if L1' is inactive and L1 is active.

L2 and L2' are redundant outputs, transmitting the same KMASS data. L3 and L3' are redundant video data inputs. There is an internal MUX which selects L3 or L3'. When the

unit is powered on, it will select L3 first (if L3 is active); otherwise, it will select L3' (if L3' is active). It will only switch from L3 to L3' if L3 is inactive and L3' is active. Likewise, it will only switch from L3' to L3 if L3' is inactive and L3 is active. The same will apply to any additional video fibers used in other models.

VelocityKVM-24WR Receiver (VEL-WR0M24-LCRX)

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 53

Typical VelocityKVM-24WR and VX160 System with Automatic Fail-Over

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 54

Appendix D- Keyboard/Mouse/Audio Control Options

Selectable KMASS/Separate KMASS

Original:

All KMASS data (keyboard, mouse, audio, etc.) sent from the TX unit is on fiber L1 along with the video data.

User RX unit receives all KMASS data on fiber L1 along with video data.

Standard (Selectable KMASS):

The Tx unit is the same as above. The RX unit can receive KMASS DATA on L1, L3, L4 and L5 along with video data. The RX unit will

select one input. Input selection is controlled by the TX unit‘s L2 back channel status. If the TX unit is receiving valid data on L2 it will send KMASS data on its L1 fiber and a status signal indicating that it has a good back channel connection. Note that Audio is always sent on L1.

The RX unit detects valid back channel status from the TX unit and will use KMASS data from the TX unit with a valid back channel. If multiple valid back channels are received, L1 has the highest priority, then L3, etc.

When no Tx has a valid back channel, L1 is used and audio will still function.

Original (Additional forward KMASS):

Same as above: Selectable KMASS with the addition of a forward KMASS fiber (K1) on TX and RX unit. K1 transfers KMASS data only, not video data. The additional fiber required for K1 can be elimated if you use a BIDI optical option. K1 and L2 can be combined on one fiber at different wavelengths. Note that L2 can also be refered to as K2 on some units.

At the RX unit, K1 has priority over L1, L3, L4 and L5, but if the RX unit is not receiving data on K1 it will then use L1, etc. for KMASS.

L2 works the same for all unit types. L2 transfers the KMASS data from the RX unit to the TX unit.

Forward KMASS only:

Same as above: Additional forward KMASS, except for the TX unit L1 output. L1 will only output video data. Note that all TX units only output KMASS data on L1 and K1, not L3, L4, or L5.

Conclusion:

Above are the present KMASS options. Other KMASS options can also be possible along with redundancy options.

Selectable KMASS HID, USB 2.0 and Control Options

HID:

Velocity HID will still function with only one connection from the RX unit to the TX unit (L2). It is also possible to control multiple CPU's from one RX unit if the L2 back channel is connected to the TX units and HID is used. The mouse may be erratic, but will still function. Note that L2 should only be connected from one RX unit to one TX unit. A broadcast connection of L2 to multiple units is incorrect and should never be done.

USB 2.0

USB 2.0 will only control one CPU at a time. It requires a full duplex connection to function, typically L1 and L2. So if L2 is broadcast to multiple TX units, USB 2.0 will only control one CPU. The CPU controlled by USB 2.0 may be different depending on what type of Velocity or T-Series extender you are using.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 55

Appendix E-

VelocityKVM Extender Series: Separate Data Paths, Separate Audio Paths and Multi-Path Video Options

Thinklogical’s® line of Separate Data Path, Separate Audio Path and Multi-Path Video Options are designed to accommodate systems that require data transmission security and for

systems with a lower video transmission rate, or for systems not transmitting video through a Thinklogical® KVM Matrix Switch.

• The VelocityKVM Separate Data Path Extender allows KMASS data

to be transmitted on one fiber and received on another fiber, separate from video data, which is transmitted on a separate, third fiber.

• The VelocityKVM Separate Audio

Path Extender allows audio signals

to be transmitted on one fiber and received on another fiber, separate from Video, USB, PS2, RS-232 and Stereo Emitter data, which are transmitted on two independent fibers

• The VelocityKVM Multi Video Path Extender allows one 6.22 Gbps DVI signal

to be transmitted across two fibers at a bandwidth of 3.11 Gbps per fiber.

Each of our Separate Data & Audio Path and Multi-Path Video VelocityKVM line of extenders is available with the full complement of options regularly available with all of our VelocityKVM extenders, such as RJ45 Network ports and various combinations of USB HID, USB 2.0 and FireWire ports.

On the following pages are examples of the various options available with each of these VelocityKVM Extender models.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 56

Separate Data Paths Option:

Separate Data Paths

Transmitter

(top) and Receiver

VelocityKVM-24K Extender Transmitter (VEL-W0DM24-LCTX) & Receiver (VEL-W0DM24-LCRX): DVI 2 Display, USB HID, USB 2.0, RS-232 Serial, Stereo Emitter, Audio, Separate Data Paths (Allows

KMASS data to be transmitted on one fiber and received on another fiber, separate from video data, which is transmitted on a separate, third fiber).

Unlike standard VelocityKVM Extenders, where data and video are transmitted together from Tx to Rx on fiber L1 and back-channel data is transmitted from Rx to Tx on a fiber designated as L2, the Separate Data Path Option keeps video on fiber L1 while data is transmitted from Tx to Rx on a separate fiber designated as K1. The back-channel data is transmitted from Rx to Tx on fiber K2, allowing for greater workstation security and system control.

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 57

Separate Data Paths Tx to Rx Application

Separate Audio Paths Option:

VelocityKVM-24WA Extender Transmitter

DVI 2 Display, USB HID, USB 2.0, RS-232 Serial, Stereo Emitter, Audio, Separate Audio Paths (Allows audio data to be transmitted on one fiber and received on another fiber, separate from Video, USB, PS2, RS-232 and Stereo data, which are transmitted on two independent fibers).

The Separate Audio Path Option allows audio signals in and audio signals out to be kept on two independent fibers designated as A1 and A2, allowing for greater workstation security and system control. USB, PS2, stereo emitter and serial data remain on fibers L1 and L2 as in standard VelocityKVM models.

Transmitter (top) and Receiver

(VEA-W00M24-LCTX)

& Receiver

(VEA-W00M24-LCRX):

CPU/Rack Mount

Operating System

router

MX48

KVM Matrix Switch

3 Rack Units 200 Watts

SOURCE

VelocityKVM-4WA

1 DVI Display, Separate

Audio Extender Tx

Network Hub

Audio

Local

OUT

Separate

Audio

Out

Local

DVI OUT

Work Station

VelocityKVM-4WA

. .

1 DVI Display, Separate Audio Extender Rx

Separate Audio IN

4 Fiber Optic Cables per Chassis

L1: System Data Tx to Rx & Video

L2: System Data Rx to Tx

A1: Separate Audio Tx to Rx A2: Separate Audio Rx to Tx

Copper Cables

DVI Video

System Data

Separate Audio

CAT5

Separate Audio Paths Tx to Rx Application

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 58

Multi-Path Video Option:

VelocityKVM-4WX Extender Transmitter

DVI 1 Display, USB HID, USB 2.0, RS-232 Serial, Stereo Emitter, Audio, Multi-Path Video (Allows one

6.22 Gbps DVI signal to be transmitted across two fibers at a bandwidth of 3.11 Gbps per fiber).

Thinklogical’s VX line of KVM Matrix Switch Routers, unlike other routers on the market, supports each

6.25 Gbps bandwidth video connection from our Velocity line of extender products. When a Thinklogical router is not part of your system, the Multi-Path Video option allows two 3.11 Gbps bandwidth video signals to transmit through a 4 Gbps router for increased system flexibility and control.

Transmitter (top) and Receiver

(VEL-W00X04-LCTX)

& Receiver

(VEL-W00X04-LCRX):

Multi-Path Video Tx to Rx Application using a 4 Gbps router

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 59

Appendix F: EDID Definition and DDC Modes

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 60

Thinklogical, LLC® 100 Washington Street Milford, CT 06460 USA 1-203-647-8700

V e l o c i t y K V M E x t e n d e r P r o d u c t M a n u a l , R e v . B , J a n u a r y , 2 0 1 4 Page 61

Thinklogical Velocitykvm-4, Velocitykvm-5, Velocitykvm-8, Velocitykvm-24, Velocitykvm-28 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual