Thinklogical Velocitydvi System-3 A/V+ Quick Start Guide

Velocity

Digital Video Extension System -

dvi

3 A/V+

QUICK START GUIDE

Each of the Thinklogical™ DVI A/V+ Extender systems is designed for high resolution video and audio extension applications such as remote projecti o n center s, theaters and assem bly halls, and fo r secure compu ter installations. It is now possible to position the monitor or projector in any setting from office to lecture hall to boardroom while keeping the computer secure in a remote, controlled location.

All physical connections to the product use industry-standard connectors.

Contents

Upon receiving your Thinklogical™

DVI Extender Transmitter DVI Extender Receiver DVI-D Male to DVI-D Male Cable,

1 Meter (CBL-000021-001MR)

DVI-D Male to DVI-D Male Cable,

2 Meter (CBL-000009-002MR)

Two CAT5 Cables, 7' (CBL-000001-007FR) Two 3.5mm Audio Cables

(CBL-000016-006FR)

Modem Adpt. DB9M RJ45 (ADP-000019-R) Modem Adpt. DB9F RJ45 (ADP-000025-R) Two Universal AC Power Adapters

(PWR-000022-R)

DVI Extender Product Manual

Power Supply

STEP 5: Connect the supplied AC

Power Adapter (PWR-000022-R) to the Transmitter unit and plug it in to a standard AC source.

The Future of access and Control

Velocity

Digital Video Extension System – 3 A/V+

Transmitter

dvi

STEP 7: Connect the Line IN and Mic OUT audio

cables and the CAT5 cable from the CPU to the appropriate Transmitter ports. Ensure that all the

devices are turned on and all system functions are operating properly.

CPU

◄ Line IN

Mic OUT ►

CAT5

DVI-D Connector 1 DVI-D Connector 2

DVI from CPUDVI to Local Display

Local Monitor

When lit, the solid green LED indicates that power is applied.

STATUS

POWER

5 VDC

L1 L2

GND

The status LEDs near the USB port on the Tx and Rx units are used to indicate the status of connections to the extender.

Tx Status LED

Green = Fiber L2 is connected and a good link is established.

Orange = Local Static Mode selected and no fiber link from Rx

to Tx (L2 is not connected) or both DDC mode buttons are held down and the unit is waiting to reload the default DDC table.

Red Flashing = No Fiber Link from Rx to Tx (Not available in

Local Static mode.)

Fiber-optic cable ports.

L1 to L1 and L2 to L2 Optical Fibers (up to 1000 meters) available with ST-, SC- or LC-type connectors

Power Supply

The Future of access and Control

Velocity

STEP 4

Connect your fiber optic cable, up to 1000 meters (available through Thinklogical™) between the Transmitter and Receiver Units. Do not kink or pinch the cable and be sure to keep all bend radii to no less than 3 inches.

L2 ◄ Data

L1 ► Video/Data

Receiver

Digital Video Extension System – 3 A/V+

Receiver

other end of the cable to the Primary (left) Receiver DVI-D connector. A second device can also

be installed to the right- side, secondary port using a similar DVI-D Male to Male cable. If using

L1 ◄ Video/Data

L2 ► Data

STEP 3

Connect the supplied AC Power Adapter (PWR-000022-R) to the

Receiver and plug it in to a standard AC source.

MRTS Technology

Transmitter

Line OUT ►

◄ Mic IN

dvi

Optional Secondary DVI Port

DVI to DisplayDVI to Display DDC

Primary DVI Port DDC

Projector

STEP 6

Connect one end of the 1 meter DVI-D Male to Male Cable (CBL-000021-001MR) to the video source (DVI-D video card). Connect the other end to the transmitter DVI-D connector. A local display may also be connected using the supplied 2 meter DVI-D Male to Male Cable (CBL-000009-002MR).

Connect your Mic IN, Line OUT

and CAT5 Serial devices to the

STEP 1

Connect one end of a DVI-D Male to Male Cable to the primary viewing device. Connect the

only one device, it must be connected to the Primary Port. Turn ON the DVI video device(s).

STEP 2

appropriate Receiver ports.

Turn the devices ON.

Secondary

DVI Port

Rx Status LED

Green = Good Link and DVI device connected to primary port

(port on left in the diagram below).

Orange = No DVI device connected to primary port.

Red Flashing = No Fiber Link from Tx to Rx (L1 is not

connected).

The Primary Port on the Rx is used for DDC. The Secondary Port carries video data only.

Acquire Button

Used to initiate DDC collection. Works with all modes except Pass-Thru. Must be pressed after switching between DDC modes.

Select Button

Used to select the DDC mode. The modes will cycle through Remote Dynamic, Remote Static, Pass-Thru and Local Static.

Both Buttons held 5 seconds

Holding both buttons for 5 seconds will reload the default DDC table into the Tx and switch to Remote Static mode.

Primary DVI Port DDC (Rx) Optional Secondary DVI Port (Rx)

DDC MODE

ACQUIRE

LCL REM

SELECT

LCL REM DDC MODE DESCRIPTION

EDID READ FROM REMOTE DISPLAY

AND UPDATED EACH TIME REMOTE

DISPLAY CHANGES.

EDID READ FROM REMOTE DISPLAY

WHEN ACQUIRE BUTTON IS PRESSED.

ACTS AS A DIRECT CONNECTION

BETWEEN CPU AND DISPLAY. NO

EMULATION IS PERFORMED.

EDID READ FROM LOCAL DISPLAY

WHEN ACQUIRE BUTTON IS PRESSED.

OFF

ORANGE

GREEN GREEN

GREEN

ORANGE

REMOTE

DYNAMIC

REMOTE

STATIC

PASS-

THRU

LOCAL

STATIC

SERIAL

MIC

LINE

OUT

PHONE: (800) 291-3211 WEBSITE: www.thinklogical.com EMAIL: support@thinklogical.com

Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical products.

VELOCITY-3AV+_Quick_Start_Rev_B