Thinklogical T-4200 Quick Start Guide

QUICK START

GUIDE

STEP 1: Connect your VelocityKVM T-4200

Transmitter Module 1 to VelocityKVM Receiver 1

using multi-mode fiber-optic cables (up to 1000

meters). Connect L1 to L1 (Data Tx to Rx & Video 1),

L2 to L2 (Data Rx to Tx) and L3 to L3 (Video 2).

As used with Thinklogical’s™ Velocitykvm T-4200 Transmitter and Velocitykvm-24 Receivers

STEP 2: Ensure the Receiver 1

ON/OFF switch is in the OFF (0)

position. Install the AC Power Cord

and plug it into a standard AC

source. Flip the ON/OFF Switch to

the ON (1) position .

DVI OUT 1 DDC

DVI OUT 2 DDC

STEP 3: Depending on your configuration, connect your

desktop devices (monitors, keyboard, speakers, etc.) to

VelocityKVM Receiver 1 using standard cables, as shown.

Turn all the devices ON.

2

PS/2 or USB

1

3

connectors

STEP 7: Turn ON the CPU that is

connected to VelocityKVM Transmitter

Module 1. Verify that all system

functions are operating properly.

CPU to T-4200

Module 1

PS2 Mouse
PS2 Keyboard

7

Audio OUT
Audio IN

HID USB

STEP 6: Connect your USB, PS/2 and Audio

sources to Transmitter Module 1’s inputs.

6

}

PWR

PWR

L1 L2 L3

USB 2.0

L2

FOL

DVI OUT 1 DDC

KMASS to TX

Module 1

ALARM

STEREO

L1

LINE IN

DVI OUT 1

L3

DVI OUT 2 DDC

Receiver 1

TX MODULE 1

PS2

HID

DEV

SER IAL PORT

DVI OUT 2

USB 2.0

CTRL

LINE OUT

MIC IN

STEP 4: On the front of the chassis, ensure that the Left Power Supply

Module ON/OFF Switch is in the OFF (0) position. Install the Left

Power Supply Module AC Power Cord (right receptacle) and plug it

into a standard AC source. On the front of the chassis, turn

ON the Left Power Supply Module ON/OFF Switch.

STEP 4: On the front of the chassis, ensure that the Right Power

Supply Module ON/OFF Switch is in the OFF (0) position. Install

the Right Power Supply Module AC Power Cord (left receptacle)

and plug it into a standard AC source. On the front of the chassis,

turn ON the Right Power Supply Module ON/OFF Switch.

L1 L2 L3

ALARM

USB HID

STEREO

LINE IN

P
S
2

HID

USB 1.1

PS2

U
P
D
A
T
E
S

DEV

CAUTION! Replace with same type and rating fuse.

HOST

CTRL

100-240V-,0.5A, 50/60 Hz

VEL-U00M24-LCRX

4

4

USB 2.0

CTRL

Caution! Remove both cords before servicing

USE ONLY WITH 250V FUSE

T 2A ,250VAC

PS2 Mouse
PS2 Keyboard

Audio OUT
Audio IN

HID USB

7

CPU to T-4200

Module 2

STEP 7: Turn ON the CPU that is

connected to VelocityKVM Transmitter

Module 2. Verify that all system

functions are operating properly.

5

5
6

DVI IN 1

STEP 5: Connect the DVI IN cables from the

CPU to VelocityKVM Transmitter Module 1.

STEP 5: Connect the DVI IN cables from the

CPU to VelocityKVM Transmitter Module 2.

STEP 6: Connect your USB, PS/2

and Audio sources to Transmitter
Module 2’s inputs.

}

PWR

USB 2.0

DVI OUT 1 DDC

FOL

DVI IN 2

L2

DVI OUT 1 DDC

MIC OUT

1

L1

DVI OUT 1

3

FROM CPU

STEP 1: Connect your VelocityKVM T-4200 Transmitter

Module 2 to VelocityKVM Receiver 2 using multi-mode

fiber-optic cables (up to 1000 meters). Connect L1 to L1

(Data Tx to Rx & Video 1), L2 to L2 (Data Rx to Tx) and

L3 to L3 (Video 2).

L3

DVI OUT 2 DDC

SER IAL PORT

DVI OUT 2

DVI IN 1

DVI IN 2

KMASS to TX Module 2

LINE OUT

MIC IN

USB HID

MIC OUT

TX MODULE 2

NOTE: The DISPLAY Switch on the front of the chassis determines if

the LCD displays DVI/KVM Module 1 or Module 2 program data.

Right Power SupplyLeft Power Supply

POWER POWER

P
S
2

PS/2 or USB

connectors

FROM CPU

Receiver 2

USB 1.1

DISPLAY

MODULE 2 MODULE 1

U
P

HOST

D
A
T
E
S

CTRL

110-240V ~, 0.5A, 50/60 Hz

VTM-U00M24-LC2T

enter

Velocitykvm T- 4200

Four Single-Link DVI Displays

CAUTION! Replace with same type and rating fuse.

USE ONLY WITH 250V FUSE

100-240V-,0.5A, 50/60 Hz

VEL-U00M24-LCRX

T 2A ,250VAC

Extend Distribute Innovate

PHONE: [phone]
WEBSITE: www.thinklogical.com
EMAIL: [e-mail]

DVI OUT 2 DDC

STEP 3: Depending on your configuration, connect your desktop devices

(monitors, keyboard, speakers, etc.) to VelocityKVM Receiver 2 using

standard cables, as shown. Turn all the devices ON.

Visit us online at www.thinklogical.com for more product information,
current updates and the complete line of Thinklogical™ products.

STEP 2: Ensure the Receiver 2 ON/OFF

switch is in the OFF (0) position. Install

the AC Power Cord and plug it into a

standard AC source. Flip the ON/OFF

Switch to the ON (1) position .

Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.

VELOCITY_T-4200TX_with_VEL-24RX_Quick_Start_Rev_A

2