Thinklogical StudioPRO Extender Single Link Quick Start Guide
CONTENTS:
StudioPRO Single-link Extender Transmitter [1]
StudioPRO Single-link Extender Receiver [1]
USB A-B cable, 6' (CBL-000015-006FR) [1]
DVI-D (M to M) cable, 2M (CBL-000009-002MR) [1]
Universal Power Supply (PWR-000022-R) [2]
StudioPRO Extender Product Manual
StudioPRO Extender
Single-Link DVI, USB 2.0 Video Extension System
QUICK START GUIDE
STEP 5:
Connect the supplied +5V power
supply (PWR-000022-R) to the transmitter
and plug it into a standard AC source.
The Future of Access and Control
POWER STATUS
StudioPRO SINGLE-LINK EXTENDER TRANSMITTER
Acquire Button
Used to initiate DDC collection. Works with all modes except Pass-Thru. Must
be pressed after switching between DDC modes.
Select Button
Used to select the DDC mode. The modes will cycle through Remote
Dynamic, Remote Static, Pass-Thru and Local Static.
Both Buttons held 5 seconds
Holding both buttons for 5 seconds will reload the default DDC table into the
Tx and switch to Remote Static mode.
LCL REM DDC MODE DESCRIPTION
EDID read from remote display and updated
each time remote display changes.
EDID read from remote display when
acquire button is pressed.
Acts as a direct connection between CPU
and display. No emulation is performed.
EDID read from local display when
acquire button is pressed.
OFF
ORANGE
GREEN
GREEN
GREEN
GREEN
GREEN
ORANGE
REMOTE
DYNAMIC
REMOTE
STATIC
PASS-
THRU
LOCAL
STATIC
StudioPRO Extender
Single-Link DVI, USB 2.0
Fiber optic transmitter
Powered by
MRTS Technology
DDC MODE
ACQUIRE
LCL REM
SELECT
STEP 7:
Connect your
USB and DVI cables
from the CPU to the
HOSTLINK
transmitter. Ensure all
system functions are
operating properly.
CPU
STEP 2:
Connect the output
display device(s) to the receiver’s
DVI TO DISPLAY ports. The DDC
port is the PRIMARY port and should
be used when there is only one
display device connected.
7
DVI TO Display
2
USB 2.0
DVI FROM CPU
DVI TO Display
DVI Local
Display
(DDC)
6
DVI LOCAL
DISPLAY
STEP 6:
Connect your
local monitor to the
transmitter’s DVI
LOCAL DISPLAY port.
L1
DVI FROM CPU
4
L3
POWER
5VDC
_
STEP 4:
+
5
Connect
your multi-mode fiberoptic cables between
the transmitter and
receiver units (up to
1000 meters).
The Future of Access and Control
POWER STATUS
StudioPRO SINGLE-LINK EXTENDER RECEIVER
StudioPRO Extender
Single-Link DVI, USB 2.0
Fiber optic receiver
Powered by
MRTS Technology
STEP 1:
peripheral devices to the
receiver’s USB 2.0 ports.
Install any USB
DDC MODE
ACQUIRE
LCL REM
SELECT
LINK
3
4
HOST
1
2
USB Devices
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: support@thinklogical.com
L3 L1
1
2
USB 2.0
3
4
DVI TO
DISPLAY
STEP 3:
DVI TO DISPLAY
(DDC)
Connect the supplied
+5V power supply (PWR-000022-R)
to the receiver and plug it into a
1
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
standard AC source.
StudioPRO_Extender_Single-link_Quick_Start_Rev_B
Visit us online at www.thinklogical.com for more product information,
current updates and the complete line of Thinklogical™ products.
POWER
5VDC
_
+
3
Loading...