Therma-Tek TF25-25 User Manual

COMMERCIAL GAS FRYER

Therma-Tek Range Corp.

115 Rotary Drive, Valmont Industrial Park
West Hazleton, PA 18202

COMMERCIAL GAS FRYER

STANDARD FEATURES

✹

Stainless steel front (TFE40).

✹

Stainless steel (or G-90 galvanized) sides (TFE40).

✹

6” (152.5 mm) adjustable legs.

✹

Type 304 stainless steel frypot standard.

✹

Two chrome plated fry baskets.

✹

1/2” NPT gas connection.

✹

Snap action mechanical thermostat 200°F (93.4°C) to 400°F (204.6°C).

✹

Millivolt pilot system requires no electrical connection.

✹

Automatic standing pilot ignition.

✹

100% safety shutoff.

✹

Large cool zone isolates food particles from the fry area.

✹

Sloped tank bottom allows oil to fully drain.

✹

Clean out rod, crumb screen, drain tube provided.

✹

Range match models TFE40, TFU40, and TF25/25.

✹

Free standing model TF75.

✹

Four year stainless steel tank warranty.

✹

One year limited parts and labor warranty.

TFE40

(shown with optional casters)

NOTE: Fryers supplied with casters must be

installed with an approved restraining device.

OPTIONAL FEATURES

✹

6" (152.5 mm) casters.

✹

Gas flex hose w/ quick disconnect and restraining device.

✹

Joiner strips for multiple units.

✹

Stainless steel tank cover.

✹

Extra fry baskets.

THERMA-TEK Sales Toll Free: 877-843-7835 Tel: [phone] Fax: [phone] [e-mail] www.therma-tek.com

COMMERCIAL GAS FRYER

8-1/4"

5

1
4

"

[133.35mm]

1/2 NPT GAS INLET

36

1-9/16"

8"

[203.20mm]

TF40

36

3

4

"

[933.45mm]

7

1
2

"

[190.50mm]

[1263.65mm]

1/2 NPT GAS INLET

49

3
4

"

"B"

A

5

1
2

"

[139.70mm]

16-3/4"

8-1/4"

[57.15mm]

17

3
4

"

[450.85mm]

MODEL # TSM36

2

1
4

"

TO

5

1
4

"

[133.35mm]

1/2 NPT GAS INLET

36

1-9/16"

8"

[203.20mm]

TF50

TF40

36

3
4

"

[933.45mm]

7

1
2

"

[190.50mm]

[1263.65mm]

1/2 NPT GAS INLET

49

3
4

"

"B"

A

5

1
2

"

[139.70mm]

36

3
4

"

[933.45mm]

7

1
2

"

[190.50mm]

[1263.65mm]

1/2 NPT GAS INLET

49

3
4

"

"B"

A

5

1
2

"

[139.70mm]

36

3
4

"

[933.45mm]

7

1
2

"

[190.50mm]

[1263.65mm]

1/2 NPT GAS INLET

49

3
4

"

"B"

5

1
2

"

[139.70mm]

Therma-Tek Range Corp.

115 Rotary Drive, Valmont Industrial Park
West Hazleton, PA 18202

"B"

A

3

36

"

4

[933.45mm]

TF40

1

7

Dimension “A” Dimension “B”

Model Number inches mm inches mm

TFE40 15.5 394 33.125 841
TFU40 15.5 394 33.125 841

2

[190.50mm]

TF25/25 15.5 394 33.125 841
TF75 19.5 495 37.375 949.3

[139.70mm]

"

1

5

"

2

1/2 NPT GAS INLET

3

49

"

4

[1263.65mm]

GAS REQUIREMENTS

Operating Manifold Gas Pressure

Natural Propane Manifold Connection Input Rating per Burner

“WC mbar “WC mbar Total BTU/Hr kW
4 9.96 10 24.9 1/2” NPT 35,000 10.26

Total gas consumption per model Gross Weight

Model Number Description Number of Burners Total BTU/Hr kW Lbs. Kg

TFE40 40 lb. Range Match Fryer 3 105,000 30.77 210 95.34
TFU40 40 lb. Range Match Fryer 3 105,000 30.77 210 95.34

TF25/25 50 lb. Range Match Split Pot Fryer 4 110,000 32.24 220 99.88
TF75 75 lb. Free Standing Fryer 5 175,000 51.29 270 122.58

NOTE: Add suffix “N” for natural gas, and “L” for propane.

CLEARANCES Sides Back
Non Combustible 0” 0”
Combustible 6” (152.4 mm) 6” (152.4 mm)

Installation Notes

This product is NOT approved for residential use.
Please advise us of installation over 2000ft. (610m) altitude.
Installation clearance reduction applies only where local codes permit.
All Therma-Tek products are covered by a one year limited parts and labor warranty.
A detailed warranty is included with the appliance or is available upon request.
Four year fry tank warranty.
Installation and/or operation by other than manufacturer’s recommendations may void warranty.

Because of continuing product improvement, these specifications are subject to change without notice.

THERMA-TEK Sales Toll Free: 877-843-7835 Tel: [phone] Fax: [phone] [e-mail] www.therma-tek.com

TF25/25

TF75

Printed July 2010
Printed in the USA