Thermador T36IT71FN/25, T36IT71FN/26, T36IT71FNS/01 Installation Guide

INSTALLATION INSTRUCTIONS
For Built-in Refrigerators, Freezers and Wine units
INSTRUCTIONS D'iNSTALLATION
Pour refrig6rateurs, congelateurs et
cave 6 vin encastres
s
DE INSTALACION
T361T71FNS
Para los refrigeradores, congeladores y unidades
de vino empotrados
9000 491 339
_efm_DI
INSTALLATION INSTRUCTIONS ................................................................................ 3
INSTRUCTIONS D'INSTALLATION ............................................................................. 25
INSTRUCCIONES DE INSTALACION .......................................................................... 48
2
Content
Before you Begin ........................................................................................................................................
General .........................................................................................................................................................
Definitions .....................................................................................................................................................
Important information ....................................................................................................................................
Installation options .....................................................................................................................................
Individual unit ................................................................................................................................................
Individual appliances with partition ................................................................................................................
At the end of the kitchen units .......................................................................................................................
Installation location .....................................................................................................................................
Installation room ............................................................................................................................................
Installation cavity ...........................................................................................................................................
Furniture/fixtures ...........................................................................................................................................
Base .............................................................................................................................................................
Connecting the power .................................................................................................................................................
Additional grounding procedure ....................................................................................................................
Grounding instruction ....................................................................................................................................
Connecting the water ..................................................................................................................................................
Installation dimensions ...............................................................................................................................
Appliance dimensions ................................................................................................................................
Required accessories and tools ................................................................................................................
Supplied accessories ....................................................................................................................................
Optional accessories .....................................................................................................................................
Other required accessories from specialist outlets .........................................................................................
Tools .............................................................................................................................................................
Other ............................................................................................................................................................
Installation instructions ..............................................................................................................................
1. Checking the installation cavity ..............................................................................................................
2. Transport of the appliance .....................................................................................................................
3. Removing the packaging .......................................................................................................................
4. Installation preparation ...........................................................................................................................
5. Preparing the installation cavity ..............................................................................................................
6. Attaching an alternative anti-tip device ...................................................................................................
7. Preparing to connect the water .............................................................................................................
8. Attaching the edge protection ...............................................................................................................
9. Pushing the appliance into the installation cavity ....................................................................................
10. Removing stainless steel front panel from the freezer compartment drawer ...........................................
11. Aligning the appliance ............................................................................................................................
5 5
5 5
6 6
6 6
7 7
7 7
7 8
8 8 8
9 10 11
11 11 11 11 11
12
12 12 13 14 14 15 16 16 17 18 18
3
12. Attaching the appliance to the top of the cavity .....................................................................................
13. Checking that the finger guard moves easily ..........................................................................................
14. Connecting the water to the appliance ..................................................................................................
15. Attaching the toe kick panel ..................................................................................................................
16. Attaching stainless steel front panel to the freezer compartment drawer ................................................
17. Commissioning the appliance ................................................................................................................
18. Attaching the individual appli-ance to the side of the cavity ....................................................................
19. Fasten the finger protection ...................................................................................................................
20. Attaching the covers ..............................................................................................................................
21. Mounting of air separator .......................................................................................................................
22. Adjusting the door opening angle (refrigerator compartment door) .........................................................
23. Changing the door spring ......................................................................................................................
19
19 2O 2O
21 22 22
23 23
24 24 24
4
Before you Begin Read these instructions completely and carefully.
/k WARNING General
These appliances are top-heavy and must be secured to
prevent the possibility of tipping forward. Anti-tip protection is required.
Keep doors closed until the appliance is completely installed
and secured per installation instructions.
Due to the weight and size of this appliance, and to reduce
the risk of personal injury or damage to the product -TWO
PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
This appliance must be properly grounded. See the section on "Connecting the power" on page 8.
Use this appliance only for its intended purpose. Immediately repair or replace electric service cords that
become frayed or damaged.
Unplug the appliance or switch off the fuse before cleaning or
making repairs.
Repairs should be made by a qualified service technician.
/k CAUTION
Skill - Level - Installation of this appliance requires basic
mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Appliance Warranty.
See the Owner's Manual for warranty information.
These installation instructions are intended for use by qualified installers. All connections for water, electrical power and grounding must comply with local codes and ordinances
and be made by licensed personnel when required. In the absence of a local code:
- Inthe U.S.A., inaccordance with the National Electric Code, ANSI/NFPA70 - latest edition/State and
Municipal codes and/or local codes.
- In Canada, in accordance with the Canadian Electric Code C22.1 - latest edition/Provincial and Municipal
codes and/or local codes.
Definitions
WARNING - This indicates that death or serious inju- ries may occur as a result of not observing this warning.
CAUTION - This indicates that minor or moderate inju- ries or damage may occur as a result of not observing
this warning.
/k IMPORTANT
Save these instructions for local inspector's use. Observe all governing codes and ordinances.
Note to Installer - Be sure to leave these instructions with
the Consumer.
Note to Consumer - Keep these instructions with your
Owner's Manual for future reference.
IMPORTANT NOTE / NOTE - This is used to draw the
user's attention to something inparticular.
Important information
The importance of complying with all regulations and
instructions inthis installation manual cannot be emphasised
enough. The installation should be carried out by a qualified fitter.
Before starting the installation, always read this installation manual in full. It contains important details which the fitter must observe. Provided this manual is read thoroughly, the installation will be simple, trouble-free and, most importantly,
safe.
5
Installation options
The different installation options are limited only by the design of the kitchen and the function of the finger guard.
Individual unit
E
Individual appliances with partition
,
At the end of the kitchen units
If one side of the appliance is visible, a side panel must be used.
The side panel must be connected firmly to the wall, the floor and overhead furniture/fixtures before the appliance isplaced
in the cavity.
The dimensions ofthe side panel are taken from the opposite cavity wall. During installation ensure that the cavity is square
and the exact size.
,
- When dimensioning the partition for model 2, note the thickness of the furniture fronts to prevent damage ifthe doors are opened at the same time.
- Use the Extreme Combination Side-by-Side Heating kit if the gap between the appliances is less than 6" (160 mm).
See the section on "Optional accessories" on page 11.
- Minimum thickness of the partition 5/8" (16 mm).
6
Installation location
Do not install the appliance:
- outdoors,
- in an environment with dripping water,
- in rooms which are at risk of frost. Appliance is very heavy - for empty weight see the
following table: BM (Bottom Mount) 36" approx. 430 Ibs / 195 kg
Installation room
The appliance should be installed in a dry, ventilated room. The ambient temperature should not drop below
55 °F (13 °C) or rise above 110 °F (43 °C), otherwise
malfunctions may occur.
The installation location should not be exposed to direct sunlight and not placed near a heat source, such as an oven,
radiator, etc. If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the
following minimum distances from the heat source:
- 11/4" (30 rnrn) from an electric cooker,
- 12" (300 mm) from an oil or solid-fuel cooker.
Furniture/fixtures
The new appliance is screwed securely to adjacent and overhead furniture/fixtures.
For this reason it isessential that all attachable furniture/
fixtures are connected securely to the base or the wall by suitable means.
Base
A fully-load appliance is very heavy - for the load- bearing capacity at least see the following table:
BM (Bottom Mount) 36" approx. 1200 Ibs / 540 kg
To ensure that the appliance is installed securely and functions properly, the base must be flat and level.
The base must be made of a hard, rigid material. The installation area must be the same height as the rest of
the room. On account of the heavy weight of a fully loaded appliance, a
load-bearing base is required. If in doubt, contact an
architect or a building expert.
Installation cavity
It is important to observe the specified dimensions of the installation cavity for a trouble-free installation of the
appliance and for the subsequent general view of the furniture front.
In particular ensure that the cavity is square.
Squareness can be checked by suitable means, e.g. spirit
level, diagonal measurements, etc. The side walls of the cavity must be flush. The minimum thickness of side walls and the top wall must
be 5/s" (16 rnrn). The minimum thickness of toe kick panel must
be 1/2" (13 rnrn). A thickness of 3/4" (19 rnrn) is recornrnended.
iiiiiiiii
Connecting the power
Electrical Shock Hazard
- Plug into a grounded 3 prong outlet.
- Do not remove ground prong.
- Do not use an adapter.
- Do not use an extension cord. Failure to follow these instructions can result in death,
fire, or electrical shock.
The appliance comes with a 3-wire power supply cord,
UL listed in the USA. The appliance requires a 3-wire receptacle. The receptacle must be installed by a licensed electrician
only. The receptacle must be fitted with a 10 A fuse or higher.
Please observe in this coherence the following table:
Appliance Maximum load at one time
Connecting the water
A cold water connection is required for operation of the automatic ice maker. The water pressure must be between
25 and 120 p.s.i. (1.72-8.25 bar). The installation must
comply with local plumbing regulations. A separate shut-off valve must be installed for the appliance
water connection. The shut-off valve for the water connection must not be
behind the appliance. It is recommended to place the shut- off valve directly next to the appliance (base unit)or in another easily accessible location.
When installing the water connection, observe the permitted
installation areas for the pipe. For the permitted installation areas and dimensions see "installation dimensions", page 9.
The supply pipecan be located at the sideon the right (a),at the side on the left (b) or underneath (c), page 9.
Maximum outer diameter of the water pipe (without fittings): 13/32" (10 rnrn).
Attach a separate shut-off valve for the water connection in a suitable, easily accessible location. Do not use aself-piercing
valve!
Bottom Freezer 36" 6 Ampere
Orient ground prong to the bottom as shown in the pictures.
Forthe installation position of the receptacle see "installation
dimensions", page 9.
Additional grounding procedure
Some local regulations may require a separate ground. In such cases, the required accessory ground wire, clamp and screw must be purchased separately.
Never ground the appliance to plastic plumbing lines, gas lines or water pipes.
Grounding instruction
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the
electric current.
Improper connection of the equipment grounding conductor may result in electric shock. Have the appliance checked by a qualified electrician or service technician if you are indoubt as to whether the appliance has been properly grounded.
8
Installation dimensions
8_
(2'
18" (457)
84"
5_"
!(130)
}315/16"/
_f (100)
ii:i
Water connection
(25)
25/_6 ,,
(59)
max.13/32,, (10)
b)
13 "
1/32
(25)
25/_6 ''
(59)
o _ max'13/32 ,,
(10)
I31/32"
25/16 ''
(59)
0 max 13/32"
i i_ii I
(10)
36" (914)
Legend:
A Area for installation of the power connection
B Area for installation of the water connection C Opening depth of niche, depending on kitchen design
D = 24" (610 ram) minimum
NOTE: Cavity must be suare.
Side wall of the cavity must be flush
e) 36"
e) 36,,
1
24"
(6"
3/32
90°
Legend:
a) Adjustrnent in levellinglegs +13/s" (35 rnrn)/-_/2" (13rnrn).
b) Dimensions may vary.
d) This dimension may vary depending on installation,panel
thickness and kitchen hardware.
d)
115° 115°
e) Unit dimensions f) Wooden door panel dimensions
t
71/8"^,
(181) dl
21346"-414d'
(71,7-106,7)
d)
10
Optional accessories
Extreme Combination Side-by-Side Heating kit Ifthe gap between the appliances is less than 6" (160 mm).
Other required accessories from specialist outlets
Ice maker installation kit 1/4" OD copper line For connecting appliances which require water, e.g. for an
ice maker. Maximum outer diameter of the water pipe (without fittings):
13/32. (10 mm).
Other
- Stepladder
- Dolly, hand truck
- Hammer drill for drilling holes in wall or floor
- Bits according suitable for material and in different sizes
- Wooden beam (cross section min. 3" x 4" (75 cm x 100
cm) as an alternative tilt protection, length according to the width of the installation cavity
- Wooden screws in different sizes
- Thin (max. 1/1G"(1.5 mm)), suitable material to protect
the floor from damage (e.g. lino)
- Suitable material for covering and protecting furniture
(e.g. protective sheets)
- Adhesive tape
Tools
- Cordless screwdriver T20
- Torx screwdriver T20
- Torx bit T20 + magnetic holder
- 5/1G"(8 mm) hex nut driver
- Wood drills in different sizes
- Open end wrench 1/2" (SW 13 mm)
- Multigrip pliers
- Adjustable wrench
- Cutter with adjustable blade
- Metal tape measure
- Square
- Spirit level length 2' (60 cm) and 4' (1,2 m)
- Marking-out level, length at least 4' (1.2 m)for individual appliances or 7' (2.0 m) for Side-by-Side installation
Before using, check whether the removed adhesive tape leaves adhesive residue on the work surfaces! Otherwise do not use on high-quality work surfaces.
11
_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i _i¸i¸ii_iii¸i¸i¸ii_ii¸ii_i_i_ii¸i¸ii_i_i_ii¸i¸ii_i_i_ii¸i¸ii_i_i_ii¸i¸ii_i_i_ii_,_,i'ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_ii_ii_ii¸il_....
Installation instructions
1. Checking the installation cavity 2. Transport of the appliance
To ensure a safe, trouble-free installation and an optimum overall view of the subsequent furniture front, thoroughly check that the installation cavity complies with the
installation requirements.
Before starting the installation, check that the installation
cavity complies with all requirements for a safe and trouble- free installation.
Check the base. Follow the instructions in the section on "installation
location" on page 7. Check the dimensions of the cavity. Check that the cavity is square.
Check location of the socket. Also follow the instructions in the section on
"Connecting the power" on page 8 and in the section on "installation dimensions" on page 9.
Check location of the water connection (only for appliances with ice maker).
Also follow the instructions in the section on "Connecting the water" on page 8.
Check attachment of the adjacent furniture/fixtures. All furniture parts in the vicinity of the appliance must be connected securely to the wall.
Check that adjacent furniture/fixtures do not collide (door opening angle)."
The appliance is very heavy. Be careful, otherwise people
who are helping may be injured or the appliance may be damaged.
Transport the appliance to a suitable installation location with suitable means of transportation (trolley, lifting truck
or hand-driven truck). Secure the appliance during transportation to prevent it
from overturning.
The appliance is 84" (2134 mm) tall. Ifthe appliance cannot
be transported in an upright position due to the structural
conditions, the appliance can be transported horizontally. When erecting the appliance, observe the required minimum
height at the installation location according to the following
table:
Erection via appliance rear Erection via appliance
side panel
86" / 2185 mm
Never put the appliance up via its side!
12
3. Removing the packaging
- The appliance may tip over while it is being unpacked.
- The appliance is very heavy.
- When opening the appliance door, the appliance may tip forwards.
Be careful, otherwise people who are helping may be injured or the appliance may be damaged.
To protect the base from damage during installation:
Attach a residual piece of carpet, lino, etc. to the floor with adhesive tape in front of the intended installation
location.
Do not remove transportation protection device (A)
from the underside of the freezer compartment drawer.
Do not remove transportation safety devices which
protect the shelves and storage compartments inside the appliance until the installation is complete,
otherwise the parts may be damaged.
A
@
Move the appliance with a hand truck securely.
@
Remove transportation packaging:
- Using adhesive tape, attach the power cord to the back of the appliance.
- Remove transportation protection devices and lift appliance off the pallet - appliance is very heavy!
- Remove accessories from the outside of the appliance.
- Keep adhesive tape which was used to attach the supplied accessories to the appliance.
It is used subsequently for attaching the edge
protection to the cavity walls (see Section 8.).
- Carefully open the appliance- risk of tipping over- and remove accessories and installation materials
from inside the appliance. Close doors again!
Check appliance for damage in transit. Do not install the appliance if it isvisibly damaged. If in
doubt, contact your dealer.
Care should be taken when closing the door. The folding rail attached to the door of the refrigerator compartment has to be folded ifthe door are closed.
Risk of damage!
13
4. Installation preparation
Unpack installation materials and accessories.
To improve allocation to the work steps, the packages are
identified differently.
To do this, comply with the overview sheet attached to the appliance!
5. Preparing the installation cavity
If this minimum length cannot be observed for structural
conditions it is possible to do this by fastening a spacer
behind the anti-tip angle, e. g. a sufficiently dimensioned
wood plank. The length of the plank should correspond to the width ofthe
installation niche!
Specify the attachment points of the anti-tip-angles. Specify the detailed dimensions according to the section
on "Installation dimensions" starting on page 9. Attach the anti-tip-angles completely. Be sure screws
hold tight.
Fastening with wood screws
Assure that there are no electrical wires or plumbing in the area which the screws could penetrate. Risk of injury and damage!
I
2 anti-tip-angles are required for each appliance.
I
The supplied set contains fastening screws for various applications. Select the fastening screws according to the local conditions.
4xl 5
Fastening with dowels and screws
Always wear safety glasses and other necessary pro- tective devices or apparel when installing or working
with anchors.
Risk of injury!
Not recommended for use in light-weight masonry material
such as block or brick.
Not recommended for use in new concrete which has not had time to cure.
Do not use core drills to drill holes for this anchor.
The anti-tip-angles must have a minimum length of 41/8"
(105 rnrn) over the appliance to ensure a secure stand of the
appliance.
14
5x60 6x31
_06
e
Attaching an alternative anti-tip
device
If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be attached. However, ensure that there is no play between the appliance and the anti-tip device.
If possible, always screw the wooden beam to existing studs on the rear panel of the cavity.
(2126,1
1/32
÷lmm
@
Mark the installation height (lower edge of the beam) on
the rear panel of the cavity.
@
Select screws according to the thickness of the wooden
beam: length -- rain. 2.5 x beam thickness, diameter #12
or #14.
Specify the number of screws according to the cavity width, thereby ensuring that the beam can be atta- ched securely.
Saw the wooden beam (cross section rnin. 3" x 4") to the required length.
Length is equal to the width of the installation cavity!
If the installation cavity is deeper than the appliance, select a beam which has a larger cross
section or attach 2 beams. The beam must cover the appliance by
at least 2" (50.8 rnrn).
According to the subsurface:
Locate wall studs near the rear panel of the cavity and mark drill holes in the beam
or
Fasten suitable dowel into the rear wall. Predrill the wooden beam.
Attach the wooden beam to the rear panel of the cavity.
15
7. Preparing to connect the water
(only for appliances which require a water connection)
Turn off the main water tap to prevent damage caused by leaking water.
@
Attach the connecting pipe to the shut-off valve according to the instructions supplied by the
manufacturer of the ice maker installation kit.
@
Install the connecting pipe. Always observe the indicated gap dimensions to prevent damage to the connecting pipe when pushing in the appliance.
8. Attaching the edge protection
@
To protect the corners of the installation cavity, attach the supplied protective brackets with adhesive tape.
>14"
Attach the connecting pipe to the floor with adhesive tape.
16
9. Pushing the appliance into the installation cavity
@
Carefully push the appliance into the cavity. Insert
appliance straight! Push in the appliance until the frame
is situated on the cavity walls. Caution when pushing the appliance into the installation cavity.
Do not damage the water pipe or power cord attached to the floor.
When the floor or the appliance is tilted in comparison to the installation cavity adjust height adjustable wheels before you move the appliance into the installation cavity.
@
Put the mains plug into the socket.
@
Prevent the power cord from becoming caught. Tie a piece of string to the middle of the power cord and
feed forwards under the appliance. When pushing inthe appliance, pull the cable forwards.
or Using adhesive tape, stick the power cord to the floor
centrally behind the appliance approx. 15" (380 mm) away from the rear panel of the cavity.
Remove the edge protection.
Remove transportation protection device from the
underside of the freezer compartment drawer.
17
10. 11. Aligning the applianceRemoving stainless steel front panel from the freezer compartment
drawer
Never use a cordless screwdriver! Risk of damage to the appliance.
iiiiiii
Loosen and unscrew nuts on the top of the door, However, do not turn the threaded bolts, otherwise the door will no longer be aligned.
Do not loosen the screws on the left and right fixing brackets. Do not unscrew the screws!
- Do not twist or jam the appliance inside the cavity! When unscrewing the height-adjustable feet,
proceed gradually: Always alternate between left
and right, left and right, etc..
- The adjustment of the rear feet is facilitated if the appliance is unloaded at the rear.
- If using a wooden beam as an alternative anti-tip device according to point 6 of this installation
manual, rotate the appliance all the way towards the
wooden beam.
@
Pull the bottom of the stainless steel front panel away from the door to remove the fixing brackets from the
screws. Then lift the door off the threaded bolts.
@
Place fixing brackets only loosely into the plates. Ensure that you do not lose them.
Remove base panel from the appliance.
18
Align the appliance with the furniture fronts.
The height-adjustable feet at the front and rear can all be adjusted from the front.
Front: with open-ended wrench 1/2" (SW13) Rear: with 5/1G"(8 mm) hex nut driver via flexible shaft.
A mark is attached to the appliance base and is used as a standard gage for height adjustment. When adjusting the
height, align this mark at a height of 11/4" (32mm) above the
floor.
@
Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension (11/4" / 32 rnrn).
It is very important to comply with this dimension for
the subsequent alignment of the furniture fronts.
@
Align the furniture fronts with the spirit level.
@
Before attaching the appliance in the cavity, check that the finger guard functions by opening and closing the two refrigerator compartment doors several times.
12. Attaching the appliance to the top of the cavity
Fix the attachment plate side lugs (top) depending on
the installation situation. Ifthere is no gap or only a slight gap, it is not necessary to fix the side lugs.
If there is a fairly large gap above the appliance, fit a wooden beam above the appliance, ensuring that the wooden beam fits the gap exactly.
4x15 I
@
Screw the attachment plate lugs (top) to the overhead furniture/fixtures.
Attach the cover strip to the attachment plate (top). Shorten the fitting strip to the required height!
13. Checking that the finger guard moves easily
It is now essential to check that the finger guard moves easily. At a later time any required corrections will be more difficult.
@
Push the finger guard on the hinge side into the gap between the appliance and cavity wall.
It must be possible to push in and pull out the finger
guard easily!
19
14. Connecting the water to the appliance
When bending the water pipe, do not kink it, otherwise there is a risk of leaks and water damage.
When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice maker installation kit enclosed
with the installation manual.
Remove the cap from the appliance connection (1.). Bend the water pipe according to the location of the
connection on the appliance (2.). Push the union nut and seal onto the water pipe. Push the end of the water pipe into the appliance
connection and screw on the union nut (3.). Tighten hand-tight.
Using the open-ended wrench, tighten the union nut. Do not overturn!
15. Attaching the toe kick panel
The maximum height of the toe kick panel is 4" from the top of the floor. Do not cover ventilation slots inthe base
panel. Risk of damage to the appliance.
If required, cut the toe kick panel to the required length.
Attach base panelling to the appliance.
@
Open the shut-off valve and main water tap. Check the connection on the shut-off valve and on the appliance
for leaks.
2O
@
Remove the protective film from the adhesive pads on
the Velcro.
@
Fit the toe kick panel to the base panel and press firmly into place.
Put on the base panel (do not screw on) and measure the difference in depth Y between the base panel and toe kick panel of the adjacent furniture.
Remove the base panel. Loosen the brackets for attaching the base panel and
push in all the way.
16. Attaching stainless steel front panel to the freezer compart-ment drawer
@
Hang stainless steel front panel over the threaded bolts.
@
Lift bottom of stainless steel front panel and push the
fixing brackets down over the screws.
@
When the freezer compartment door is closed, check the depth of the stainless steel front panel with respect to the adjacent furniture front panels.
If the depth alignment is correct, tighten the screws on
the fixing brackets.
Pull out the brackets by the measured amount Y. Screw the brackets tightly.
Attach the base panel.
If required, the toe kick panel can be screwed to the base panel. There are screw holes inthe base panel
near the Velcro.
Screw nuts onto the threaded bolts on top of the door.
Do not tighten yet. Check lateral alignment of the stainless steel front panel.
If the lateral alignment is correct, tighten the nuts.
21
17. Commissioning the appliance
Check that the finger guard functions. Inparticular check
- that the finger guard is correctly attached to the appliance and
- that the finger guard slides smoothly forwards and backwards when the refrigerator compartment
doors open and close.
To guarantee the accuracy of the following working steps and thus the appearance of the overall kitchen front later on,
the appliance should now be operated.
Open the appliance door. Press the POWER button.
Only for appliances with a water connection:
In order to avoid the risk of damage caused by leaking water from damage possibly caused to the water pipe feeding the appliance, keep the shut-off valve closed.
To take out, lift the drawer slightly and take out.
18. Attaching the individual appli-ance to the side of the cavity
The drawers in the freezer compartment must be taken out
in order to attach the appliance.
Before the door drawer can be taken out, the upper drawer must be removed.
@
Using a screwdriver, turn catches on the telescopic rail by 90° .
A Appliance
B Cabinet part
Screw the attachment plate lugs (C) to the adjacent furniture/fixtures.
Screw on the brackets (D) for holdingthe cover strip.
22
Loading...
+ 50 hidden pages