Thermador PRD484EEHU/01, PRD304EHU/07, PRD304EHU/06, PRD304EHU/04, PRD304EHU/03 Installation Guide

...

INSTALLATION MANUAL

For Thermador Professional ® PRO-HARMONY TM Dual Fuel Ranges

MANUEL D'INSTALLATION

Pour toutes les cuisinieres mixtes

Thermador Professional ® PRO-HARMONY TM

Models/ Modeles / PRD30 PRD36 PRD48

Table of Contents

Safety Instructions ............................ 1

Important Safety Instructions ........................................ 1

Important Installation Information ............... 2

Step 1: Ventilation Requirements .................................... 3

Step 2: Cabinet Preparation ........................................ 5

Step 3: Unpacking, Moving and Placing the Range ..................... 10

Step 4: Installing Anti-Tip Device ................................... 12

Step 5: Gas Requirements and Hookup ............................. 15

Step 6: Electrical Requirements, Connection & Grounding ............... 17

Step 7: Backguard Installation ..................................... 22

Step 8: Door Removal and Reinstallation ............................. 24

Step 9: Burner Test and Adjustment ................................. 25

Installer Checklist ............................................... 27

To Clean and Protect Exterior Surfaces ......... 29

This Thermador Appliance is made by

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

For Massachusetts Installations:

1. Installation must be performed by a qualified or licensed contractor, plumber or gas fitter qualified or licensed by the state, province or region where this appliance is being installed.

2. Shut-off valve must be a "T" handle gas cock.

3. Flexible gas connector must not be longer than 36 inches.

WARNING

If the information in this manual is not followed exactly, a fire or Iexplosion may result causing property damage, personal injury or Ldeath.

Do not store or use gasoline or other flammable vapors and liq- uids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance. Do not touch any electrical switch.

Do not use any phone in your building. Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions. If you cannot reach your gas supplier, call the fire depart- ment.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING

All Ranges can tip Injury to Persons could result

Install Anti-Tip Device See Installation Instructions

TO REDUCE THE RISK OF TIPPING OF THE APPLIANCE, IT

MUST BE SECURED BY A PROPERLY INSTALLED ANTI-TIP DEVICE. VERIFY THAT THE ANTI-TIP DEVICE IS ENGAGED

PER INSTALLATION INSTRUCTIONS. (NOTE: ANTI-TIP DEVICE IS REQUIRED ON ALL 30" AND 36" RANGES).

Safety Instructions

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

APPROVED FOR ALL RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

IMPORTANT: Save these Instructions for the Local Electrical and Gas Inspectors' use.

INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference.

Important:

Note:

_ WARNING

Local codes vary. Installation, gas connections and grounding must comply with all applicable codes.

_ WARNING

Disconnect power before installing. Before turning power ON, be sure that all controls are in the OFF position.

This Range is NOT designed for installation in manufactured (mobile) homes or for installation in Recreational Park Trailers.

Do Not install this range outdoors.

Disconnect power before installing. Before turning power ON, be sure

that all controls are in the OFF position.

Do not use a flame of any kind to check for gas leaks.

Page 1

_iiii_ i i _ !_Zi_!Y: ii_i¸ii_iM__i;i_iii__i;i_ii#i_i__ Zi_ _____";;i_/___" i_ i ____ ___iiiii_i!_i___iii_i_i ¸I_iii_!?______ii_ii _ _;_;_;_;i__ii __;_;_;_;_;_;_;_;_;_;_;_!S_,!',;. _i;i__iiiiii_iiiiiiiii__i¸iii__ _iiiiiiiiiiii_i_iii_i_iii_iii_T__iiiiii_i_iii_iii_T_iiii_ii_i/ii_ii_i_!!ii!ii!i_i¸__i__i__i__i__i__i/_i_iii_iiii/i/i_i_i_i_i_i_i_i;_iI_i_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iii_Iiii¸;__ii/ii/ii/ii/_i

Important Installation Information

GAS type verification

Important:

Verify the type of gas supplied to the location. Ensure that the appliance is con- nected to the type of gas for which it is certified. All models are certified for use with natural gas. Field conversion of the appliance for use with propane gas supply will require a conversion kit.

_ WARNING

Refer to "Chart C: Backguard Kit Model Numbers" on page 23, for the correct backguard models that are designed for this range, After selecting the correct backguard, the range must be installed properly, using the minimum clear- ances to combustible surfaces specified in the Cabinet Preparation instruc-

tions on Page 5,

A backguard must be utilized when there is less than a 12" horizontal clearance between combustible materials and the back edge of the range. A Thermador backguard must be ordered separately and installed at the rear of the range (A Low Back is supplied with 30" model). For island installations and other installa-

tions with more than 12" clearance, an optional stainless steel Island Trim is

available to cover the backguard mounting flanges. Verify that the appliance is correct for the type of gas being provided. Refer to "Step 5: Gas Requirements and Hookup" on page 15 before proceeding with the

installation.

To avoid possible burn or fire hazard, a backguard designed specifically for this range must be installed whenever the range is used.

Gas Supply:

Electric Power Supply:

This appliance has been tested in accordance with ANSI Z21.1, Standard for Household Cooking Appliances (USA) and in accordance with CAN 1.1-M81 Domestic Gas Ranges (Canadian).

It is stronqlv recommended that this appliance be installed in conjunction with a suit- able overhead vent hood. (See "Step 1:Ventilation Requirements" on page 3.) Due

to the high heat capability of this unit, particular attention should be paid to the hood

and duct work installation to assure it meets local building codes.

Check local building codes for the proper method of appliance installation. Local codes vary. Installation, electrical connections and grounding must comply with all applicable codes. In the absence of local codes the appliance should be installed in

accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54 current issue and National Electrical Code ANSI/NFPA 70-current issue. In Canada, installation

must be in accordance with the CAN 1-B149.1 and .2 - Installation Codes for Gas Burning Appliances and/or local codes.

Natural Gas- 6 inch water column. (14.9 mb) min., 14 inch (34.9 mb) maximum

Propane Gas - 11 inch water column. (27.4 mb) min., 14 inch (34.9 mb) maximum

(See Page 17 for specifications.)

Page 2

CAUTION

When connecting the unit to propane gas, make certain the propane gas tank is equipped with its own high-pressure regulator in addition to the

pressure regulator supplied with the range. The maximum gas

pressure to this appliance must not exceed 14.0 inches water

column (34,9 mb) from the propane gas tank to the pressure

regulator,

,_ CAUTION

This appliance complies with one or more of the following standards:

It is the responsibility of the owner and the installer to determine if additional require- ments and/or standards apply to specific installations.

Due to the high heat of the cooktop burners, installing a microwave oven with a ven-

tilation system over the cooktop is not recommended.

,_ CAUTION

This unit is designed as a cooking appliance. Based on safety considerations, never use it for warming or heating a room.

UL 858, Standard for the Safety of Household Electric Ranges UL 923, Standard for the Safety of Microwave Cooking Appliances UL 507, Standard for the Safety of Electric Fans ANSI Z21.1, American National Standard for Household Cooking Gas Appli-

ances CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

CAN/CSA-C22.2 No. 61-M89 Household Cooking Ranges

To eliminate risk of burns or fire caused by reaching over heated surface

units, cabinet storage located above the surface units should be avoided.

Step 1: Ventilation Requirements

It is stronqIv recommended that a suitable exhaust hood be installed above the range. Downdraft ventilation should not be used. The Table on page 5 indicates the

ventilation hood options and blower capacity guidelines that are recommended for

use with all Thermador ranges.

Select Hood and Blower Models: For wall installations, the hood width must, at a minimum, equal the width of the

range cooking surface. Where space permits, a hood larger in width than the cooking surface may be desirable for improved ventilation performance. For island installations, the hood width should overhang the range cooking sur- face by a minimum of 3" on each side.

Important: Ventilation hoods and blowers are designed for use with single wall ducting.

However, some local building codes or inspectors may require double wall ducting. Consult local building codes and/or local agencies, before starting, to assure that hood and duct installation will meet local requirements.

Do not install a microwave oven/ventilator combination above the range, as these type of units do not provide the proper ventilation and are not suitable for use with the range.

Page 3

30"

4 burners

Hood Placement: For best smoke elimination, the lower edge of the hood should be installed 36"

above the range cooking surface. (See Figure 1). If the hood contains any combustible materials (i.e. a wood covering), it must be a minimum of 40" above the cooking surface.

Consider Make-Up Air: Due to the high volume of ventilation air, a source of outside replacement air is recommended. This is particularly important for tightly sealed and insulated

homes. A qualified heating and ventilating contractor should be consulted.

36" Chimney Hood w/optional blower

600 CFM

30" or 36" Custom Insert w/optional blower

30" or 36" Pro Wall Hood

42" Island Hood w/optional blower

36"

4 burners w/grill or

griddle

6 burners

800 CFM

900 CFM

36" or 42" Chimney Hood w/optional blower

36" or 42" Pro Wall Hood

36" Custom Insert w/optional blower

42" Island Hood w/optional blower

4 burners w/grill-griddle

48" Chimney Hood w/optional blower

48" or 54" Pro Wall Hood

48" Custom Insert w/optional blower

54" Island Hood w/optional blower

48"

combo or

24" griddle

6 burners w/grill or

1000 CFM

1100 CFM

griddle

Important Notes:

It is recommended that a Thermador Professional wall or island hood or custom insert is used with Thermador Pro- fessional Ranges.

Refer to www.thermador.com for a complete selection of Professional Ventilation options, Blowers, and Accesso- ries.

* For high output gas ranges (60,000 BTU or greater), the minimum of one (1) CFM of ventilation per 100 BTU is recommended. If the range has a grill or griddle, add 200 CFM to the estimated blower capacity. Additional blower capacity may be required for longer duct runs. For island applications, it is recommended to use a hood width that exceeds the width of the range by 6" (overlap- ping the range by a minimum of 3" on each end). CFM = "cubic feet per minute" (standard blower capacity rating).

Page 4

Step 2: Cabinet Preparation

1. The range is a free standing unit. If the unit is to be placed adjacent to cabinets, the clearances shown in Figure 1 are required. The same clearances apply to

island installations, except for the overhead cabinets, which must have a space wide enough to accept the flared island hood, as indicated in Figure 1.

2. These ranges may be recessed into the cabinets beyond the edge of the front

face of the oven (See Figure 2a and Figure 2b).

,_ CAUTION

3. The gas and electrical supply should be within the zones shown in Figure 3a.

Note: The maximum depth of over head cabinets installed on either side of the hood is

13".

A 40-inch minimum clearance is required between the top of the cooking surface and the bottom of an unprotected cabinet. A 36-inch distance can be used when the bottom of the wood or metal cabinet is protected by not less than 1/4 inch of a flame retardant material covered with not less than No. 28 MSG sheet steel, 0.015 inch (0.4 mm) thick stainless steel, 0.024 inch (0.6 mm) aluminum, or 0.020 inch (0.5 mm) thick copper. Flame retardant materials bear the mark:

UNDERWRITERS LABORATORIES INC. CLASSIFIED MINERAL AND FIBER BOARDS SURFACE BURNING CHARACTERISTICS

Followed by the flame spread and smoke ratings. These designations are shown as "FHC (Flame Spread/Smoke Developed)." Materials with "O" flame spread ratings are flame retardant. Local codes may allow other flame spread ratings.

4. Any openings in the wall behind the range and in the floor under the range must

5. When there is less than a 12" horizontal clearance between combustible mate-

type of backguard.

6. Always keep appliance area clear and free from combustible materials, gasoline

7. Do not obstruct the flow of combustion and ventilation air to the unit.

8. A (4) inch minimum clearance is needed when the range is installed beside a

In these installations, the door and cabinet can cause a pinching hazard.

be sealed.

rial A and the back edge of the range above the cooking surface, a Thermador Low Back or Pot and Pan Shelf must be installed. (See Figure 2a). When clear-

ance to combustible material A is over 12", a Thermador Island Trim may be used. (See Figure 2b). Figures 2a and 2b indicate the space required for each

and other flammable vapors and liquids.

combustible side wall.

A As defined in the "National Fuel Gas Code" (ANSI Z223.1, Current Edition).

Page 5

For 30" Ranges { 36"or42"forlsland

30"or36"Wide Hood

T 36"frombotto n ofoverhead

Hoodtocooking surface (40" min. ifhood contains

18"

Min. combustible materials Z_ )

o 1

For 36" Ranges { 36"or42"WideHood

For 48" Ranges {48", 54", or 60" Wide Hood

ForElectrical and Gas Supply Zone,see Figure3A.

42"or48" for Island

54" or 60" for Island

of CombustibleMaterial A

30" Range-30" 36" Range - 36" 48" Range -48" 13" Max.

Cabinet _

Depth "

Rangewidth

30", 36", or48"

Cooking Surface

CAUTION: See

4" Min.to combustible sidewall

material A,

(bothsides)

Figs. 2A and 2B 40" Min. to combustible

material A , from cooking

surface

i o

'35-7/8" Min. RangeHeight with Leveling Legs fully

retracted

"36-3/4" Max. Range Height with Leveling Legs fully

extended.

Z_ as defined in the "National Fuel Gas Code" (ANSI Z223.1,

Current Edition). *The range height is adjustable. The level of the range top must be at the same level or above the countertop level.

Figure 1: Cabinet Clearances

Page 6

40" min. to_ combust-

iblesA

,,_ 27 5/8"

26 1/2"

Pot and

combustible

materials z&

1/4"

36 3/4" max. 35 7/8" min.

Pan Shelf _ - -

LowBack Guard_

Front Face

_4 3/4':

_4_22 1/2'-'

I I

_, (36"

Wall

22"

Note:

/'_ as defined in the "National Fuel Gas Code" (ANSI Z223.1, Current Edition).

Figure 2a: Side View

With the oven door fully open, the top of the door extends to 44-5/8" from the back wall, behind the range when installed. Installation must allow ample clearance for

movement around the door when fully opened.

* Refers to 30", 36" and 48" range models.

Page 7

40" min. to

combustiblesA

36 3/4" max. 35 7/8" min.

combustible/

materialsA--

12" min. to

combustiblesA

with island trim

island trim

Countertop

front face

Note:

A as defined in the "National Fuel Gas Code" (ANSI Z223.1, Current Edition).

Figure 2b: Side View

With the oven door fully open, the top of the door extends to 44 5/8' from the back wall, behind the range when installed. Installation must allow ample clearance for movement around the door when fully open.

Page 8

Gas and Electric Supply

Gas & Electrical Supply Locations for 30" and 36" Dual Fuel Ranges

electrical gas

supply zone supply zon

30 1/4" (30" models) 36 1/4" (36" models)

Gas & Electrical Supply Locations for 48" Dual Fuel Ranges

Note:

°F

R_eptacle or Junction Box

48-1/4'

Figure 3a: Gas & Electrical Supply Locations for Dual Fuel Ranges

If not already present, install gas shut-off valve in an easily accessible location. Make sure all users know where and how to shut off the gas supply to the range.

The installer should inform the consumer of the location of the gas shut-off valve,

Any opening in the wall behind the appliance and any opening inthe floor under the appliance must be sealed.

The dual fuel ranges may be connected to the power supply with a range supply cord kit or by hard-wiring to the power supply. It is the responsibility of the installer to provide the proper wiring components (cord or conduit and wires) and complete the electrical connection as dictated by local codes and ordinances, and/or the National

Electric Code. The units must be properly grounded. Refer to Step 6 for details.

Canadian models have power cord supplied.

The range must be connected only to the type of gas for which it is certified. If the range is to be connected to propane gas, ensure that the propane gas supply tank is equipped with its own high pressure regulator in addition to the pressure regulator supplied with the range. (See Step 5.)

Page 9

Note:

The range is designed for flush installation to the back wall. For a successful installation, it may be necessary to reposition the gas-supply line and electrical cord as the range is pushed back to its final position. SUGGESTION: This may be accomplished by carefully pulling on a rope or twine looped around the gas or electrical supply line as the range is pushed back into its final installed

position.

Electrical Supply

Note:

Installation of the range must be planned so that rough-in of junction box for the receptacle or conduit connection will allow maximum clearance to the rear of the

unit.

When the power supply cord or conduit is connected to the mating receptacle or

junction box cover, the combined plug/receptacle or junction box cover/conduit con-

nector should protrude no more than 1 3/4" from the rear wall for 30" and 36" Ranges; 2" maximum protrusion from the rear wall for 48" Ranges. See Figure 3b.

Refer to Figure 9 on Page 19 for location of junction box on unit. To minimize bind- ing when the unit is connected to the receptacle or junction box, orient the recepta- cle or conduit connector, and slide back into position.

Canadian models have power cord supplied with range.

When using a 240VAC receptacle having its own housing, it will be necessary to recess the receptacle's housing into the rear wall. Mount the receptacle securely to a wall stud, then seal around the receptacle's housing. Follow all local electrical

codes.

1 3/4" max .... _,_ _ ...........

2" max. for 48" range I

For 48" Ranges:

2" maximum protrusion from

rear wall.

..... 1 3/4" max. when plugged in.

Power Cord & Receptacle

2" max. for 48" range

Junction Box & Conduit

Figure 3b: Wall Connection

Step 3: Unpacking, Moving and Placing the Range

,_ CAUTION

Page10

Proper equipment and adequate manpower must be used in moving the range to avoid injury, and to avoid damage to the unit or the floor. The unit is heavy and should be handled accordingly.

The range has an approximate shipping weight as shown in Chart A. It is rec- ommended that the grates, griddle/grill plate and frame, burner caps, front kick panel and oven racks be removed to facilitate handling. This will reduce the

weight as shown in Chart A and allow the range to pass through 30" doorways. See Figure 2a and Figure 2b on Page 7 and Page 8. Do not remove the grill or griddle assemblies, Remove the outer carton and packing material from the shipping base. The dual fuel ranges are held to the pallet by four (4) bolts (see Figure 4). After removing

the bolts, the range must be lifted and removed from the pallet.

Important:

DO NOT lift the range by the oven door handle, as this may damage the door hinges and cause the door to fit incorrectly to the oven cavity.

Shipping Weight 351 Ibs. 371 Ibs. 499 Ibs. Weight without packing materi-

als

228 Ibs. 270 Ibs. 403 Ibs.

Without doors, burner caps, 185 Ibs. 221 Ibs. 318 Ibs. front kick panel and oven racks

Note:

Pallet

Figure 4: Removal of the Four (4) Shipping Bolts

Leave adhesive-backed foam layer over brushed-metal surfaces, to protect finish from scratches, until the range is installed in final position.

Due to the weight, a dolly with soft wheels should be used to move this unit. The weight must be supported uniformly across the bottom (See Figure 5).

After transporting the range by dolly close to its final location, the range can be

tipped back and supported on the rear legs while the dolly is carefully removed.

THE FLOOR UNDER THE LEGS SHOULD BE PROTECTED BEFORE PUSH- ING THE UNIT INTO POSITION, The anti-tip device must be installed (Step 4), gas and electrical connections should be made (Step 5 and Step 6), and the

backguard installed (Step 7) before the range is placed in its final position. For proper performance, the range must be level. (It is very important for all

products that have the griddle or grill feature.) The range is leveled by adjusting

the legs with a wrench.

Replace the kick panel. It is important that the screws retaining the kick panel are secure to prevent accidental access to hot surfaces.

Page 11

Ensurethattheburnercapsarecorrectlyseatedontheburnerbasesofthe range'scooktop.

Range Must be

Uniformly Supported

by Braces Provided

on Bottom of Range

Figure 5: Dolly Positioning

Remove all tape and packaging before using the appliance. Destroy the pack- aging after unpacking the appliance. Never allow children to play with packaging

material.

Important: DO NOT lift the range by the oven door handle, as this may damage the door hinges

and cause the door to fit incorrectly to the oven cavity.

Grill/Griddle Tilt Adjustment (Not All

Models)

If the range is equipped with an electric griddle or gas grill, check the grill/griddle

frame adjustment by pouring two tablespoons of water on the back of the griddle or

grill plate. The water should slowly roll into the grease tray. If not, adjust the two screws under the back of the frame. Start with one half turn counterclockwise

(CCW) of the screws. Further adjustment should be made by one-quarter turn until water slowly flows into the grease tray.

Step 4: Installing Anti-Tip Device

For 30" and 36" ranges, an anti-tip device must be installed as per these instruc-

tions.

_ WARNING - RANGE TIPPING HAZARD

All ranges can tip and injury can result. To prevent accidental tip- ping of the range, attach it to the floor, wall or cabinet by installing

the Anti-Tip Device supplied.

A risk of tip-over may exist if the appliance is not installed in accor- dance with these instructions.

If the range is pulled away from the wall for cleaning, service or any other reason, ensure that the Anti-Tip Device is properly reengaged when the range is pushed back against the wall. In the event of abnormal usage (such as a person standing, sitting, or leaning on

an open door), failure to take this precaution can result in tipping of the range. Personal injury might result from spilled hot liquids or from the range itself.

Page12

_ WARNING - ELECRICAL SHOCK HAZARD

Use extreme caution when drilling holes into the wall or floor. There

may be concealed electrical wires located behind the wall or under the floor.

Identify the electrical circuits that could be affected by the installa- tion of the Anti-Tip Device, then turn off power to these circuits.

Failure to follow these instructions may result in electrical shock or

other personal injury.

WARNING

• All Ranges can tip

• Injury to Persons could result

• Install Anti-Tip Device Packed with

Range

• See Installation Instructions

ATTENTION - PROPERTY DAMAGE

Contact a qualified installer or contractor to determine the proper

method for drilling holes through the wall or floor material (such as

ceramic tile, hardwood, etc.)

Do not slide the range across an unprotected floor.

Failure to follow these instructions may result in damage to wall or

floor coverings.

Important Installation Information:

Tools Needed for Installation of Anti-Tip Device:

Screwdriver, Phillips Drill, electric or hand

Measuring tape or ruler 1/8" drill bit (wood or metal wall or floor)

Hammer Pencil or other marker

3/16" carbide-tipped masonry drill bit (concrete or concrete block wall or floor) 3/16" anchors, drywall or concrete, 4 each (not required if mounting bracket is being attached to solid wood or metal)

For 30" and 36" Dual Fuel Ranges (Figure 6 and Figure 7)

415078 4 Screw, Phillips, #10 x 1-1/2" 427338 1 Anti-Tip Bracket, Floor-Mounted

The anti-tip bracket may be attached to a solid wood cabinet having a minimum wall thickness of 3/4".

The thickness of the wall or floor may require use of longer screws, available at your local hardware store. In all cases, at least two (2) of the bracket mounting screws must be fastened to

solid wood or metal.

Page13

Useappropriateanchorswhenfasteningthemountingbrackettoanymaterial otherthanhard-woodormetal.

Prepareholesatfastenerlocationsasidentifiedbelow:

Figure 6: Mounting Anti-tip Bracket

I 4-7/8" 14 from edgeof range

Wall Line

f ..... /7-- -I" \

Mounting Anti-Tip Bracket

Floor

Left Cabinet

t Y///////_

Front Edge of _I 14 4=7/8" _ __,_

RightCabinet typical-

t _ either side)

Figure 7: Placement of Anti=Tip Bracket (Top View)

Y////////

For walls, wall studs, or floors composed of solid wood or metal, drill 1/8"

pilot holes.

For walls or floors composed of drywall, sheet-rock or other soft materials, drill 3/16" holes to a minimum depth of 1-3/4", then tap plastic anchors into each of the holes using a hammer.

For walls or floors composed of concrete or concrete block, drill 3/16" holes to a minimum depth of 1-3/4", then tap concrete anchors into each of the holes using a hammer.

For walls or floors havinq ceramic tile coverinq, drill 3/16" holes through the tile only, then drill into the material behind the tile as indicated immediately

above.

If the range is moved to a new location, the Anti-Tip Device must be removed and reinstalled.

The alternative floor mounted bracket shall be installed as follows:

Page 14

1. Place bracket on floor in position shown in Figure 7 (Bracket may be used in either corner of the installation area).

2. Secure to floor or wall stud.

3. Later, when the unit is installed, the adjustable leg will slide under the bracket.

Step 5: Gas Requirements and Hookup

Verify the type of gas being used at the installation site• The appliance is shipped

from the factory for use with natural gas, It must be converted for use with

propane, A qualified technician or installer must do the conversion, Make cer-

tain the range matches the type of gas available at this location•

For installation of the appliance at high altitude, please consult your local gas com- pany for their recommendation of the correct orifice sizes and any other necessary adjustments that will provide proper gas combustion at specified altitudes•

The field conversion kit for this series of Dual Fuel Ranges is Thermador Model PLPKIT. Obey all instructions in PLPKIT for correct conversion of the gas regulator and settings for the gas valves•

This appliance has been CSA certified for safe operation up to an elevation of 10,200 ft. without any modifications• Exception: For use with propane, the appliance must be converted per the LP conversion instructions•

_1_ CAUTION

Inlet Connection:

Supply Pressure:

Manifold Pressure:

Inlet Connection:

Supply Pressure:

Manifold Pressure:

When connecting unit to propane gas, make certain the propane gas tank

_sequipped with its own high pressure regulator in addition to the pressure regulator supplied with the appliance• The pressure of the gas

supplied to the appliance regulator must not exceed 14" (34.9 mb) water column•

Natural Gas Requirements:

1/2" NPT internal (Minimum 3/4" dia. flex line)

6" min. to 14" max. water column

(14.9 to 34.9 mb)

5" water column (12.5 mb)

Propane Gas Requirements:

1/2" NPT internal (Minimum 3/4" dia. flex line)

11"min. to 14"max. water column (27.4 mb to

34.9 mb) 10" water column (24.9 mb)

Hook Up

_ ARNING

The supply line must not interfere with the back of the unit. Make sure the gas

Gas line must not come in contact with any components inside back

cover of range• Run gas line in channel in back of range•

A manual gas shut-off valve must be installed external to the appliance, in a location accessible from the front, for the purpose of shutting off the gas supply•

supply is turned off at the manual shut-off valve before connecting the appli- ance.

The range is supplied with its own pressure regulator that has been perma- nently mounted within the range body.

Page15

Use3/4"flexlinetoconnectbetweenthegassupplyandtheappliancemanifold pipe,whichexitstheupperrearoftheapplianceon30"and36"ranges.(See PhotoA:.Thegassupplylineconnectionislocatedatthelowerrightportionof 48"rangemodels.(SeeFigure8).Theappliancemanifoldpipeconnectionis 1/2"NPT.Usecautiontoavoidcrimpingthe3/4"flexlinewhenmakingbends. Suggestedlengthofflexlineis48";however,pleasechecklocalcodesforyour area'srequirementsbeforeinstallation. Thegassupplyconnectionsshallbemadebya competenttechnicianandin accordancewithlocalcodesorordinances.Intheabsenceoflocalcodes,the

installationmustconformtotheNationalFuelGasCodeANSIZ223.1/NFPA54- currentissue.

AlwaysusepipesealingcompoundorTeflon®tapeonthepipethreads,andbe carefulnottoapplyexcessivepressurewhentighteningthefittings. Leaktestingoftheapplianceshallbeinaccordancewiththefollowinginstruc-

tions.

Turnongasandchecksupplylineconnectionsforleaksusinga soapand

watersolution.

Bubblesformingindicateagasleak.Repairallleaksimmediatelyafterfind-

ingthem.

_1_ WARNING

Do not use a flame of any kind to check for gas leaks.

Use 3/4" flex line to connect between the gas

supply and the appliance manifold pipe.

Channel

for gas

/line

Photo A: Appliance Manifold Pipe Connection

Page16

, !

'\ ./

Figure 8: Location of Gas Supply Inlet Connection on 48" Ranges

Step 6: Electrical Requirements, Connection & Grounding

Prior to servicing appliance, always disconnect appliance electrical supply cord, if so equipped, from wall receptacle. If appliance is hard-wired to power supply,

disconnect power to unit by turning off the proper circuit breaker or disconnect- ing the proper fuse. Lock service panel to prevent power from being turned ON

accidentally.

Dual Fuel range models can be connected or hardwired to the power supply as described on Page 19.

iiiiiii_iiiiii_!H_iiiiii!ii!!I!iiiiiil!ii_ _iii!i!iii!_/iiiiiii_i_i_ii¸ii'iiii!!_i_!i_liil iii! i

35 Amps x 2

30" 240/208 VAC (35 Amps each

line)

35 Amps x 2

36 _' 240/208 VAC

240/208 VAC48 _'

A neutral supply wire must be provided from the power source (breaker/fuse panel) because critical range components, including the surface burner spark

reignition module, require 120 VAC to operate safely and properly. An improper 120/240 VAC power supply will cause malfunction, damage this appliance, and

possibly create a condition of shock hazard. If the correct power supply circuit is not provided, it is the responsibility and obligation of the installer and user to

have proper power supply connected. This must be accomplished in accor-

(35 Amps each

line)

50 Amps x 2

(50 Amps each

line)

60 Hz. Single

Page17

+ 44 hidden pages