Thermador PH60GS Installation Manual

THERMADOR PROFESSIONAL SERIES® 60'' Wall Hoods

Hottes Murales de la Série 60'' PROFESSIONAL

MC

de THERMADOR

Para Campanas de Pared 60'' PROFESSIONAL® de THERMADOR

Table of Contents (English)................................................................ 2

Table de Matières (Français) ........................................................... 21

Índice de Materias (Español)........................................................... 41

Models | Modèles | Modelos

PH60GS

Table of Contents

Safety ............................................................................................................................................................................... 3

Advanced Planning ......................................................................................................................................................... 5

Before You Begin........................................................................................................................................................ 5

General Information .................................................................................................................................................... 6

Installation Preparation................................................................................................................................................... 7

Installation Considerations ......................................................................................................................................... 7

Electrical Requirements .............................................................................................................................................. 7

Ductwork Preparation ................................................................................................................................................ 8

Choosing the Correct Blower ...................................................................................................................................... 10

Hood Transition........................................................................................................................................................... 10

Installation Instructions.................................................................................................................................................. 12

Wall Mount Installation................................................................................................................................................ 12

Cabinet Installation ..................................................................................................................................................... 14

Wire Routing ............................................................................................................................................................... 16

Blower Motor Installation............................................................................................................................................. 16

Grease Trays, Filters and Spacers ............................................................................................................................. 20

Heat Lamp Installation ................................................................................................................................................ 20

Customer Support, Accessories & Parts ........................................................................................................ back page

Safety Definitions

WARNING

This indicates that death or serious injuries may occur as a result of non-observance of this warning.

CAUTION

This indicates that minor or moderate injuries may occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.

Note: This alerts you to important information and/or tips.

This THERMADOR® appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Table of Contents English | 2 |

Safety

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: Please leave these Instructions with this unit for the owner. Save these Instructions for the Local Inspector’s use.

OWNER: Please retain these instructions for future reference.

WARNING

If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury.

DO NOT repair or replace any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage or void product warranty. Refer to this manual for guidance. All other servicing should be done by an authorized servicer.

CAUTION

The unit is heavy and should be handled accordingly. Proper safety equipment such as gloves and adequate manpower of at least two people must be used in moving the hood to avoid injury and to avoid damage to the unit or the floor.

Rings, watches, and any other loose items that may damage the unit or otherwise might become entangled with the unit should be removed.

Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with the following Standards:

• UL 507, Standard for the Safety of Electrical Fans

• CAN/CSA-C22.2 No. 113, Fans and Ventilators

It is the responsibility of the owner and installer to determine if additional requirements and/or standards apply to specific installations. Always refer to local codes to ensure all requirements are met.

If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit.

INSTALLER — show the owner the location of the circuit breaker. Mark it for easy reference.

WARNING

Turn off power circuit at service panel and lock out panel before wiring this appliance. Requirement: 120 VAC, 60 Hz 20 A. Allow the appliance to cool after the power has been turned off before servicing the appliance.

WARNING

To reduce the risk of fire use only metal ductwork.

CAUTION

Vent unit to the outside of building only. This unit is only designed to be vented outside. It should not be used for recirculation mode.

WARNING

Repairs should only be done by a trained servicer. Improper repair of your appliance may result in risk of severe physical injury or death.

WARNING

When properly cared for, your new appliance has been designed to be safe and reliable. Read all instructions carefully before use. These precautions will reduce the risk of burns, electric shock, fire, and injury to persons. When using kitchen appliances, basic safety precautions must be followed, including these in the following pages.

Installation Instructions English | 3 |

Never modify or alter the construction of the appliance. For example, do not remove panels or wire covers.

Examine the appliance after unpacking it. In the event of transport damage, DO NOT plug it in.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Grounding Instructions

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.

Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

WARNING

Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

WARNING To Reduce The Risk Of Fire Or Electric Shock

DO NOT use this fan with any solid-state speed control

devices.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS OBSERVE THE FOLLOWING:

• This ventilator assembly must be installed with THERMADOR Customer Service for additional options.

• Use this unit only in the manner intended by the manufacturer. If you have questions, contact Customer Service at 1-800-735-4328.

• Before servicing or cleaning unit, switch power OFF at the service panel. Lock the service panel to prevent power from being turned ON accidentally. When the service panel cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

• Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

®

recommended blowers only. Contact

• Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• To properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings,

attics, crawl spaces or garages.

WARNING

Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area.

CAUTION

For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials or vapors.

WARNING State of California Proposition 65 Warnings:

This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING

Halogen lights might be hot. Disconnect from power and allow to cool before servicing.

Installation Instructions English | 4 |

Advanced Planning

Before You Begin

CAUTION

Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally.

Parts Included

Metal transition with backdraft damper

Stainless steel baffle filters

Tools and Parts Needed

Aluminum tape (DO NOT use duct tape) 1/2'' (13 mm) Conduit if required (follow local codes) 1'' (25.4 mm) Strain relief EXTNCB25 – 25 ft. Blower Connector Cable for distances

up to 25 ft. Ducting as needed Blower Flat head and Phillips screwdrivers Drill with 3/16'' (4.76 mm) drill bit 3/8'' (9.52 mm) nut driver or socket and ratchet Wire stripper Protective work gloves

Optional accessories available for separate purchase. Refer to www.thermador.com for more details.

Literature packet

Filter spacers

Grease trays

175W Heat lamps

Remote blower adapter

Wooden bracket used as Hood Mounting Bracket (part of install- DO NOT THROW AWAY)

Fastener assortment

EXTNCB25 – 25 ft. Blower Connection Cable

IMPORTANT: DO NOT throw away any packaging until appliance is fully installed.

WARNING

To avoid risk of burn, turn the hood ON when cooking at high heat or when flambéing food.

DO NOT use all heating elements or gas burners simultaneously at high settings for a prolonged period. (max.15 minutes).

If the hood is located over a gas cooktop, operate the hood at maximum setting whenever three or more gas burners are being used.

DO NOT operate the ventilation system during a cooktop fire.

Installation Instructions English | 5 |

General Information

7½"

(190)

12"

(305)

12"

(305)

18"

(457)

27"

(686)

4

3

/

"

(106)

59

/

"

(1523)

dia. 10" (254)

Overall Dimensions of the 60'' Pro Wall Hood

PH60GS — This model series features brushed stainless-steel filters, halogen lights, and heat lamps.

inches (millimeters)

dia. 10"

dia. 10" (254)

(254)

7½"

(190)

12"

(305)

18"

(457)

27"

(686)

NOTE: Transition is centered.

6"

(152)

151515

59

(1523)

12"

(305)

3

"

4

/

161616

(106)

"

/

161616

Figure 1: PH60GS Overall Dimensions

Installation Instructions English | 6 |

Installation Preparation

* 30" (762) min. 40" (1,016) max. to Cooking Surface

7½"

(190)

18"

(457)

NOTICE: The hood could incur some damage from heat if

Installation Considerations

a THERMADOR PROFESSIONAL rangetop is operated with multiple burners at high settings under a hood that is installed at minimum clearances.

®

series range or

18"

(457)

* 30" (762) min.

* 30" (762) min. 40" (1,016) max.

40" (1,016) max. to Cooking Surface

to Cooking Surface

* Follow cooking appliance manufacturer’s recommendations

7½"

(190)

Cooking Surface

Electrical

Zone

inches (millimeters)

Unit Weight

When calculating the load for the housing support system, be sure to consider the weight of the ventilation unit.

Weight

Hood, Filters, Grease Trays, and Spacers 104 lb (47 kg) Integral Blower Model VTN1090 23 lb (11 kg)

IMPORTANT:

The supplied weights address only the ventilation unit and blower. Installer must account for weight of any materials of construction when calculating the total dead weight load of installation, including but not limited to: wall, tile, mortar, plaster, brick, finishes, partitions, and other similarly incorporated architectural and structural items. It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

Table 1: Unit Weight with Blower

Blower Motors

Figure 2: Typical Hood Installation

Hood Width

The hood width should be no less than the width of the

cooking surface. For proper performance, the housing must cover the entire cooking surface.

For proper performance, the hood must be centered horizontally above the cooking surface.

Distance From Cooking Surface

Hood installation height above a cooktop, rangetop or range can vary. The installation height ranges from a minimum height of 30'' (762 mm) to a maximum height of 40'' (1,016 mm); however, it is necessary to follow the cooking appliance manufacturer’s installation instructions for proper hood height (Figure 2).

Integral, in-line and remote blowers are available through your authorized THERMADOR® dealer. For local dealer information, visit the Find a Dealer section of our website at www.thermador.com.

The blower will vary in size and is dictated by the cooking surface, the volume of air that needs to be moved and the length of the duct run. Refer to the Ventilation Planning Guide for detailed blower motor information.

Electrical Requirements

The unit requires a 120V AC, 60Hz. 20A branch circuit.

The hood should only be connected to a dedicated circuit (with ground) that has been installed according to relevant regulations.

Installation Instructions English | 7 |

When connected to a GFCI-protected supply,

THERMADOR PROFESSIONAL

use in damp locations that are protected from outside weather conditions and not subject to saturation with water and other liquids, but can be subject to moderate degrees of moisture (such as an outdoor covered patio or lanai area). Refer to local codes, NEC/CEC, and or the Authority Having Jurisdiction (AHJ) for additional information.

Check your local building codes for proper method of installation. In the U.S., if there are no applicable local codes, this unit should be installed in accordance with the National Electric Code ANSI/NFPA No. 70, Current Issue. In Canada, installation must be in accordance with the CAN 1- B149.1 and .2 - Installation Codes for Gas Burning

Appliances and/or local codes.

The appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric shock by providing a wire that allows the electric current to

escape.

WARNING

The appliance must be grounded.

®

hoods are suitable for

Electrical Data on the Data Rating Plate

Data, including the model and serial number, is located on the product data rating plate inside the appliance, visible after removal of the filter frame (see Figure 30 on page 20).

DO NOT USE FLEXIBLE DUCT; it creates back pressure/ air turbulence and reduces performance. Always use metal ductwork.

Always install a metal vent cover where the ductwork exits the house. Hood must be vented to the outside of

building only.

COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air flow and a nonmetallic thermal break to minimize conduction of outside temperatures as part of the ductwork. The damper should be on the cold air side of the thermal break. The break should be as close as possible to where the ducting enters the heated portion of the house.

MAKE-UP AIR: Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

For safety reasons, ducting should vent directly outdoors (not into an attic, underneath the house, into the garage or into any enclosed space). The unit cannot be used in conjunction with a recirculation unit.

®

THERMADOR (15.24 m) equivalent length of duct.

recommends not exceeding 50 ft

Ductwork Preparation

Discharge Direction

The hood can be mounted on a wall or suspended from a

cabinet. Both vertical and horizontal discharge are possible with either mounting method.

Ducting Recommendations

Proper performance is dependent upon proper ducting. Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than specified cubic feet per minute (CFM) of air movement. The specified CFM varies from locale to locale. It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

NOTE: The 25 ft. Blower Connector Cable accessory (EXTNCB2) will only work for distances up to 25 ft. DO NOT use more than one Blower Connector Cable per installation.

Keep duct runs as short and straight as possible. Elbows and transitions fittings reduce air flow efficiency. Back to back elbows and “S” turns give very poor delivery and are not recommended.

A short straight length of duct at the inlet of a remote blower gives the best delivery.

Hoods are supplied with a 10" (254 mm) round transition. A locally supplied transition is required for other sizes.

Use Table 2 on page 9 to compute permissible lengths for duct runs to outdoors.

Installation Instructions English | 8 |

Equivalent Duct Lengths for Commonly Used Transitions

Duct Piece

Smooth Straight

3¼" x 10" Straight

3¼" x 14" Straight

90° Elbow Round

45° Elbow Round

Size of Duct

Piece (in)

6 1.2

7 0.95

8 0.7

10 0.6

N/A 1

N/A 0.7

612

78

86

65

74

83

Equivalent Length (ft)

Duct Piece

3¼" x 10" to Round 90° Elbow

3¼" x 10" Center Reverse Elbow Left

3¼" x 10" Center Reverse Elbow Right

3¼" x 10" Left Reverse Elbow

3¼" x 10" Right Reverse Elbow

Round Wall Cap

Size of Duct

Piece (in)

610

75

N/A 15

N/A 25

N/A 15

N/A 25

62

72

82

10 2

Equivalent Length (ft)

3¼" x 10" 90° Elbow Round

3¼” x 10" 45° Elbow Round

3¼" x 10" Flat Elbow

Round to 3¼" x 10"

3¼" x 10" to Round

Round to 3¼" x 10" 90° Elbow

N/A 5

N/A 15

N/A 20

61

71

65

73

610

78

62

Round Roof Cap

2' Long 3¼" x 10" Flex

3¼" x 10" to Round

7" Inline Backdraft Damper

3¼" x 10" Roof Jack and Shutter

NOTE: These commonly used installation parts can be purchased at a local hardware store. THERMADOR® does not manufacture all these parts.

72

82

N/A 20

10 1

7

N/A

Table 2: Duct Lengths

Installation Instructions English | 9 |

Choosing the Correct Blower

7½"

(190)

Hood Transition

It is recommended to use only THERMADOR blowers with

THERMADOR ventilation hoods. Consult the Ventilation

Planning Guide for recommended blowers. Contact Customer Service for additional options (see the back page for contact information).

IMPORTANT: Cutting off a connector to the appliance, blower, or to the extension cable kit will void the warranty.

Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most efficient air-Àow exhaust, use a straight run or as few elbows as possible (refer to “Ductwork Preparation” on page 8).

Integral Blowers

These blowers are integrated into the hood at the time of

installation.

Remote Blowers

Discharge Direction

The hood can be mounted on a wall or suspended from a cabinet. Both vertical and horizontal discharge are possible with either mounting method.

VERTICAL DISCHARGE

The hood is shipped ready for vertical discharge.

The transition supplied with the hood connects to standard 10-inch round duct. Figure 3 shows the transition connected for vertical discharge.

inches (mm)

6"

(152)

7½"

(190)

Depending on preference and ducting situation, these blowers can be mounted on the roof or exterior wall of the home. An exterior installation may be more appealing to reduce noise in the kitchen.

The 25 ft. Blower Connector Cable Accessory

(EXTNCB25) is available to connect the hood to the Remote Blower for distances up to 25 ft. Accessory cable must be purchased separately. DO NOT use more than one Blower Connector Cable per installation.

Inline Blowers

To minimize noise in the kitchen, these blowers are

mounted along the duct line anywhere between the kitchen and the exterior wall. If there is easy access to duct line (in an attic, for example), this may be an appealing option.

The 25 ft. Blower Connector Cable Accessory

(EXTNCB25) is available to connect the hood to the Inline Blower for distances up to 25 ft. Accessory cable must be purchased separately. DO NOT use more than one Blower Connector Cable per installation.

18"

(457)

Figure 3: Transition Centerline for Vertical Discharge

HORIZONTAL DISCHARGE

The transition supplied with the hood connects to standard 10-inch round duct. Figure 4 shows the transition connected for horizontal discharge.

inches (mm)

Figure 4: Transition Centerline for Horizontal Discharge

7½"

(190)

10"

(255)

Installation Instructions English | 10 |

1. To change to horizontal discharge, move the discharge

7½" (190)

25½" (647)

18"

(457)

cover, shown in Figure 5, to the top of the hood. The plate is held in place by (4) 3/8'' hex nuts.

Figure 5: Discharge Direction

Assembly of the Transition

The supplied transition mounts to the top or rear of the

hood, depending on the discharge direction.

A minimum height clearance of 7½'' (190 mm) is needed above the hood for transition mounting. See “Before You Begin” on page 5 for overall hood dimensions.

2. Depending on direction of discharge, align mounting holes at base of transition with the mounting holes of the ½'' (13 mm) flange located at the top or rear of the hood.

3. Fasten transition to hood using four (4) 1/4'' (6 mm) sheet metal screws included with hood (Figure 7).

4. Seal connection between transition and hood with aluminum tape. DO NOT use duct tape. Ensure that

the connection is completely sealed (Figure 7).

25½"

(647)

7½"

(190)

18"

(457)

inches (mm)

Figure 7: Transition Connection

5. Remove tape holding damper closed.

Figure 6: Transition Dimensions

Installation Instructions English | 11 |

Installation Instructions

18"

(457)

25½" (647)

*Hood mounting Heights

Minimum 30" (762)

Maximum 40" (1016)

27" (687)

Distance to cooking surface plus 16½" (419)

Wood Bracket (included)

3" (76) screws

Cooktop Centerline

Hood mounting bracket

Wall Mount Installation

Determine installation height

25½"

25½" (647)

(647)

Minimum 30" (762)

27" (687)

18"

(457)

*Hood mounting Heights

Maximum 40" (1016)

1. Turn power OFF at the service panel. Lock service

2. After the hood installation height has been determined,

3. Find the centerline of the hood. Draw a vertical line

4. The hood is mounted to the wall using the wooden

5. Locate a stud on both sides of the hood centerline to

panel to prevent power from being turned ON.

draw a horizontal line at a distance above the cooktop equal to the recommended hood installation height plus 16½'' (419 mm). This line is the mounting location of the wooden bracket shipped with the hood.

along this centerline up to the horizontal line drawn in Step 2.

bracket shipped with the hood. Remove the wooden bracket located at the top side of the hood by removing the two shipping screws. Mark the center line of the wood bracket.

use for mounting the wooden bracket as shown in Figure 9.

inches (mm)

Figure 8 shows a typical installation of the hood. The installation height ranges from a minimum height of 30'' (762 mm) to a maximum height of 40'' (1016 mm); however, it is necessary to follow the cooking appliance manufacturer’s installation instructions for proper hood height.

NOTICE: The hood could incur some damage from heat if a THERMADOR PROFESSIONAL rangetop is operated with multiple burners at high settings under a hood that is installed at minimum clearances.

*Follow cooking appliance manufacturer’s recommendations

inches (mm)

Figure 8: Typical Hood Installation

®

series range or

Distance to

cooking surface

cooking surface plus 16½" (419)

plus 16½" (419)

Cooking Surface

Wood

Wood Bracket

Bracket (included)

(included)

3" (76)

3" (76) screws

screws

Cooktop Centerline

Figure 9: Mounting the Wooden Bracket

Installation Instructions English | 12 |

6. Align the top of the wood bracket along the horizontal

28" (713)

30

" (762)

6

" (152)

Conduit

Zone

12

" (305)

7" (178)

Hood mounting heights

30"– 40" (762 –1016) from cooking surface.

30" (762)

12" (305)

line drawn in Step 2. Align the centerlines of the bracket and cooktop.

7. Drill a 3'' (76 mm) deep 3/16'' (3 mm) tap hole through the wooden bracket, wall, and into the stud.

8. Use three, 3'' (76 mm) screws to attach the bracket to the wall, as shown in Figure 9. For support of the hood, use three studs. Countersink the screw heads to prevent interference with the hood.

9. On the wood bracket, mark the locations used to hang the hood according to Figure 10.

2 x 1½" (38) 2" (51)

28" (713)

Horizontal discharge wall cutout

HORIZONTAL DISCHARGE installations require a wall cutout, as shown in Figure 12, to provide clearance for the transition. The location of the cutout is determined by the

hood installation height.

Back Wall

inches (mm)

30" (762)

"

(305)

12" (305)

12

12"

(305)

7" (178)

Hood mounting heights

30"– 40" (762 –1016) from cooking surface.

Electric Conduit

Zone

28" (713)

inches (mm)

Figure 10: Hanging the Hood

10. Drill a 3/16'' (4.8 mm) tap hole through the wooden bracket and wall. These 5/8'' (16 mm) screws do not need to go into the studs.

11. Use (2) 5/8'' (16 mm) screws to secure the wood bracket leaving

¼'' (6 mm) of each screw exposed for

hanging the hood.

Vertical discharge ceiling cutout

VERTICAL DISCHARGE installations require a cutout in the ceiling to accommodate 10'' (254 mm) duct and 5/8'' (16 mm) diameter clearance hole for ½'' (12.7 mm) conduit

to the j-box (Figure 11).

inches (mm)

6

" (152)

6

" (152)

30

" (762)

12

" (305)

Conduit

Zone

Figure 12: Horizontal Wall Cutout Dimensions

Prepare for the wire routing

12. Remove junction box channel covering the wires (Figure 13, “A”).

13. Remove circular knockouts behind junction box channel (Figure 13, “B”).

“B”

“A”

Figure 13: Junction Box Channel

Figure 11: Vertical Ceiling Cutout Dimensions

Installation Instructions English | 13 |

14. Install strain relief (not included) into one of the circular

“K” x4

“L” x2

19/16

"

(40)

(179)

59"

(1499)

knockouts.

Figure 14: Strain Relief

Mounting hood to the wood bracket

15. Before hanging hood, install transition per Figure 3 or Figure 4. Fasten transition with (2) 3/8'' sheet metal screws (supplied) and aluminum tape per all applicable codes.

18. From inside the hood, drive 5/8'' (16 mm) screws through holes in hood into wooden bracket. See holes labeled “J” in Figure 15.

19. Connect additional ducting.

Cabinet Installation

The hood can be installed under a cabinet by supporting the hood from the top.

Ensure both knockouts have been removed.

NOTE: The cabinet must be structurally joined to the wall studs to support the weight of this hood.

Figure 16 shows the (4) keyholes labeled “K” used for mounting the hood to the bottom of the cabinet.

inches (mm)

“L” x2

NOTE: Screws must not hinder damper operation.

16. Using two people to lift, rest the hood on the screws in the wood bracket. Use the keyholes labeled "F" in Figure 15. Make sure the wood bracket fits into the recess on the back of the hood.

J

F

Figure 15: Location of Screw Holes

17. Tighten the screws in keyholes. Check hood levelness and adjust if necessary.

59"

(1499)

“K” x4

9

1

/16

19/16

(40)

71/16 (179)

(179)

"

L

Figure 16: Tap Hole and Screw Hole Locations

1. In the base of the cabinet, drill 1/8'' (3 mm) tap holes 59'' (1,499 mm) apart, as indicated in Figure 16.

2. Screw in (4) 1" (25 mm) screws (provided with hood) leaving 1/4'' (6 mm) exposed to hang the hood on.

Installation Instructions English | 14 |

Vertical Discharge Cabinet Cutout

30

" (762)

6

" (152)

Conduit

Zone

12

" (305)

7" (178)

Hood mounting heights

30"– 40" (762 –1016) from cooking surface.

30" (762)

12" (305)

VERTICAL DISCHARGE installations require a cutout in the ceiling to accommodate 10'' (254 mm) duct and 5/8'' (16 mm) diameter clearance hole for ½'' (12.7 mm) conduit to the j-box (Figure 17).

inches (mm)

6

" (152)

6

" (152)

30

" (762)

30

" (762)

" (305)

12

" (305)

12

Figure 17: Transition and Conduit Locations

Conduit

Zone

Horizontal Discharge Cabinet Cutout

3. Hang hood from keyhole screws and tighten securely.

4. From inside of hood, insert screws supplied. Drill through holes, use 5/8'' (16 mm) screws supplied, (1) on each side and (6) along the front, into bottom of the cabinet. See screw holes labeled "L" in Figure 16.

Prepare for the wire routing

1. Remove junction box channel covering the wires (Figure 19, “A”).

2. Remove circular knockouts behind junction box channel (Figure 19, “B”).

“B”

“A”

For HORIZONTAL DISCHARGE, use Figure 18 for the geometry of the cutout required for clearance of the transition. The location of the cutout is determined by the hood installation height.

Back Wall

inches (mm)

"

(305)

12" (305)

12

12"

(305)

7" (178)

30" (762)

Hood mounting heights

30"– 40" (762 –1016) from cooking surface.

Figure 18: Horizontal Wall Cutout Dimensions

Electric Conduit

Zone

Figure 19: Junction Box Channel

3. Install strain relief (not included) into one of the circular knockouts.

Figure 20: Strain Relief

Installation Instructions English | 15 |

Wire Routing

Route wires here

Blower Motor Installation

Vertical Discharge Wire Routing

Route wires here

Figure 21: Vertical Discharge

Horizontal Discharge Wire Routing

Route wires here

Blower SKU Voltage Current Circuit Breaker

Remote

Inline

Integral

a

Indicates a letter designating the release year.

WARNING

Cutting the plug of the blower will void the warranty or eligibility for return or exchange.

CAUTION

To reduce the risk of fire and electric shock, install this range hood only with the blowers listed in the Ventilation Planning Guide.

All hoods require the choice of a Remote, Inline, or Integral Blower. Use only THERMADOR® blowers with THERMADOR ventilation hoods. All blower models are sold separately. See the Ventilation Planning Guide for recommended blowers. Contact Customer Service for additional options.

VTR1330

VTI1010

VTN1090

a

120 8.8 20 amp

a

120 5.7 20 amp

a

120 5.4 20 amp

Table 3: Blower & Circuit Breaker Ratings

Figure 22: Horizontal Discharge

The hood is rated for 120 VAC, using a 20 amp circuit breaker.

Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most efficient air-Àow exhaust, use a straight run or as few elbows as possible (refer to “Ductwork Preparation” on page 8).

Installation Instructions English | 16 |

Integral Blower Installation Only

10⅞" (275)

13⅛"

(335)

8¼" (208)

18⅞"

(473)

Integral Blower models are integrated into the hood at the time of installation.

For complete installation instructions see the instructions supplied with the blower unit.

1. The blower is attached to the hood using weld studs provided on the mounting plate. Guide the motor mounting plate over the studs (Figure 23).

2. Attach (4) nuts (included with hood) to the weld studs. Tighten nuts to secure the blower to the hood.

Integral Blower models are integrated into the hood at the time of installation. For complete installation instructions see the instructions supplied with the blower unit.

1. Remove junction box channel covering the wires (see Figure 13 on page 13).

2. Remove circular knockouts.

3. Install strain relief (not included) into one of the circular knockouts.

4. Connect the blower’s Molex plug connector to the connector present inside the hood, as shown in

Figure 25.

From Blower

From Control Panel

Figure 23: Weld Stud Locations

Wiring the Hood with an Integral Blower

inches (mm)

18⅞"

18⅞" (473)

10⅞"

(275)

Figure 25: Wiring the Hood with an Integral Blower

5. Connect the power supply wires to the hood wires in the following order: black to black, white to white, and green wire to green ground screw on chassis. Use spring type wire nuts.

• Spring type wire nuts rated for a minimum of two

(2) #18 gauge wires and maximum of four (4) #14 gauge wires, UL & CSA rated to 600V and 302°F (150°C.)

6. Close the junction box cover.

13⅛"

(335)

8¼"

(208)

Figure 24: Integral Blower Model

Installation Instructions English | 17 |

Wiring the Hood with a

Brown

Green/Yellow

White

Red

Blue

Orange

Remote Blower

Depending on preference and ducting situation, these blowers can be mounted on the roof or exterior wall of the home. An exterior installation may be more appealing to reduce noise in the kitchen.

For complete installation instructions see the instructions supplied with the blower unit.

2⅛" (54)

13⅝"

(346)

dia.

12⅛" (308)

(251)

(254)

9⅞"

10"

20¾" (527)

inches (mm)

12⅞" (327)

1⅞" (48)

6½"

(165)

2⅛" (54)

4. Install 1'' (25.4 mm) conduit connectors.

5. Run black, white, and green wires (#12 AWG) in 1'' (25.4 mm) conduit from the power supply to the junction box.

6. Connect the power supply wires to the hood wires in the following order: black to black, white to white, and green wire to green ground screw on chassis. Use spring type wire nuts.

• Spring type wire nuts, rated for a minimum of two

(2) #18 gauge wires and maximum of four (4) #14 gauge wires, UL & CSA rated to 600V and 302°F (150°C).

7. Connect the “pigtail” to the connector inside the junction box.

SPEED 1

SPEED 2

SPEED 3

NEUTRAL

WH / BC / BL (16 AWG)

BK / N / NE (16 AWG)

RD

BU

BN

WH

120V, 60HZ, 20A POWER SUPPLY

SP4

GROUND

N

SP1

SP2

SP3

L1NT1T2S3

Brown

Green/Yellow

White

Red

Blue

Orange

19⅞" (505)

Figure 26: Remote Blower

1. Remove junction box channel covering the wires (see Figure 13 on page 13).

2. Remove circular knockouts (Figure 13 on page 13).

3. Install strain relief (not included) into one of the circular knockouts.

Figure 27: Wiring the Hood with a Remote Blower

8. Close the junction box cover.

9. Run five (5) #14 AWG wires in 1'' (25.4 mm) conduit from the remote blower to the second conduit connector.

10. Connect the remote blower to the pigtail wires as per Figure 27. Connect the remote blower green (ground) wire to the ground screw in the junction box. Refer to the blower installation instructions for further wiring details.

Installation Instructions English | 18 |