Thermador PH36GS, PH42GS, PH48GS, PH54GS, PH30HS Information Sheet

...
Page 1
130
MODELS SHOWN: HPIN48HS ISLAND HOOD, PRD486GDHU PRO HARMONY® RANGE AND T24IW800SP FREEDOM®WINE PRESERVATION COLUMN
Page 2
VENTILATION
PROFESSIONAL & MASTERPIECE
VENTILATION
®
SERIES
2010 Masterpiece Series Hood
1.800.735.4328 | THERMADOR.COM
131
Page 3
RANGE, RANGETOP AND VENTILATION MATRIX
PROFESSIONAL SERIES
= PERFECT FIT = VIABLE OPTION
27-INCH DEPTH, 18-INCH TALL
WALL HOODS
24-INCH DEPTH, 18-INCH TALL
WALL HOODS
24-INCH DEPTH, 11-INCH TALL
WALL HOODS
36" PH36GS
42" PH42GS
48" PH48GS
54" PH54GS
30" PH30HS
36" PH36HS
48" PH48HS
30" HPWB30FS
36" HPWB36FS
48" HPWB48FS
36-INCH
PRO GRAND
48-INCH
PRO GRAND
27-INCH DEPTH
48-INCH
PRO GRAND STEAM
42" HPIN42HS
ISLAND HOODS
CUSTOM INSERTS
For optimal performance, the width of the hood should equal that of the cooktop or rangetop or exceed it by 3 inches on either side. Install these hoods only with Thermador Blowers.
48" HPIN48HS
36" VCIN36JP / 36" VCIB36JP
48" VCIN48JP / 48" VCIB48JP
54" VCIN54JP / 54" VCIB54JP
132
Page 4
VENTILATION
30-INCH
PRO HARMONY
36-INCH
PRO HARMONY
24-INCH DEPTH 24-INCH DEPTH
48-INCH
PRO HARMONY
30-INCH
RANGETOP
36-INCH
RANGETOP
48-INCH
RANGETOP
1.800.735.4328 | THERMADOR.COM
133
Page 5
COOKTOP AND VENTILATION MATRIX
MASTERPIECE® SERIES
36-INCH
INDUCTION/
= PERFECT FIT = VIABLE OPTION
30" HMWN30FS
30-INCH
INDUCTION
FREEDOM
INDUCTION
30-INCH
GAS COOKTOP
36-INCH
GAS COOKTOP
WALL HOODS
WALL HOODS
WITH BLOWER
CHIMNEY WALL HOODS
CHIMNEY WALL HOODS
WITH BLOWER
DRAWER HOOD
WITH BLOWER
36" HMWN36FS
48" HMWN48FS
30" HMWB30FS
36" HMWB36FS
36" HMCN36FS
42" HMCN42FS
36" HMCB36FS
42" HMCB42FS
36" HDDW36FS
40" HMIB40HS
134
42" HPIB42HS
ISLAND HOODS
WITH BLOWER
CUSTOM INSERTS
DOWNDRAFTS
For optimal performance, the width of the hood should equal that of the cooktop or rangetop or exceed it by 3 inches on either side. Install these hoods only with Thermador Blowers. *Compatible with cooktops of widths up to 42" †Also compatible with Pro Grand Ranges, Pro Harmony Ranges and Professional Rangetops.
48" HPIB48HS*
30" VCI230DS
36" VCI236DS
48" VCI248DS
30" UCVM30FS
36" UCVM36FS
Page 6
VENTILATION
30-INCH
ELECTRIC COOKTOP
30-INCH SENSOR
ELECTRIC COOKTOP
36-INCH
ELECTRIC COOKTOP
36-INCH SENSOR
ELECTRIC COOKTOP
1.800.735.4328 | THERMADOR.COM
135
Page 7
BLOWER SELECTION AND DUCT GUIDE
PROFESSIONAL SERIES
Type
Type Model No.
WALL
HOODS
ISLAND
HOODS
CUSTOM INSERTS
Available
Sizes (Widths)
PH_GS 36" / 42" / 48" / 54"
HPWB_FS
PH_HS 30" / 36" / 48"
HPIN_HS 42" / 48"
VCIB_JP 36" / 48" / 54" 1000
VCIN_JP 36" / 48" / 54"
30" 600
36" / 48" 1000
Blower Information
600
1000
600 1000 1300
600 1000
600 1000 1300
600 1000
600 1000
600 1000 1300
600 1000
600 1000 1300
600 1000
600 1000
CFM
Remote
Inline
Integrated
Model No.
VTN630C 10.3
VTN1030C 13.6
VTR630D 12.1 VTR1030D 14.0 VTR1330E 17.5
VTI610D 12.1
VTI1010D 14.0
Included 3.4 Included 10.2
VTR630D 6.9 VTR1030D 8.8 VTR1330E 12.3
VTI610D 6.9 VTI1010D 8.8 VTN630C 5.0
VTN1030C 8.4
VTR630D VTR1030D VTR1330E
VTI610D
VTI1010D
Included 12.7
VTR630D 6.9 VTR1030D 8.8 VTR1330E 12.3
VTI610D 6.9 VTI1010D 8.8 VTN630C 10.3
VTN1030C 13.6
Total Amps @
Max 10
Amps
120 Volts, 60 Hz
136
MASTERPIECE® SERIES
30"
WALL
HOODS
CHIMNEY
WALL HOODS
ISLAND HOODS
CUSTOM INSERTS VCI2_DS 30" / 36" / 48"
DOWNDRAFT UCVM_FS 30" / 36"
*Purchase separately at most hardware stores, unless otherwise indicated with a Thermador model number.
HMWN_FS
36" / 48"
HMWB_FS 30" / 36" 600
HMCN_FS 36" / 42"
HMCB_FS 36" / 42" 600
HDDW36FS 36" 600
HMIB40HS 40" 400
HPIB_HS 42" / 48" 600
600 600
1000
600
1000
600
1000
600 1000 1300
600 1000
1000
600 1000 1300
600 1000
600 1000 1300
600 1000
600
600 1000
600 1000
••
••
VTN600F 4.6 VTR630D 4.3
VTR1030D 7.8
VTI610D 5.8
VTI1010D 7.6
VTN600F 4.6
VTN1000F 8.8
VTR630D 4.3 VTR1030D 7.8 VTR1330E 9.2
VTI610D 5.8
VTI1010D 7.6
Included 3.4
VTN1080F 5.0
VTR630D 6.7 VTR1030D 7.8 VTR1330E 9.2
VTI610D 5.8
VTI1010D 7.6
Included 4.9 Included 4.9 Included 5.2 Included 5.2
VTR630D 5.2 VTR1030D 7.8 VTR1330E 9.5
VTI610D 5.8
VTI1010D 7.6
VTN600CV2C 6.7
VTR630D 6.7 VTR1030D 10.2
VTI610D 5.8
VTI1010D 7.6
Page 8
VENTILATION
Duct Size at BlowerRoofplate Required
Transition with
Backdraft Damper
Duct Size at Discharge Discharge Direction
RFPLT600
RFPLT1000
6-Inch
8-Inch
10-Inch
Hood Information
Included
Required*
6-Inch
8-Inch
10-Inch
Vertical
Horizontal
Side & Down
•••
•••
•••
•••
•••
•••
•••
••
••
•• ••
••
••
•••
•• ••
•• ••
•• ••
••
••••
••••
••
•••
••
••
•• ••
•• ••
••
•••
••
••
Recirculation
Capability
••
••
••
•••
••
••
••
••
••
••
•••
••
••
•••
•• •••
•••
•••
•••
•••
••
••
•••
•••
••
•• ••
•• ••
••
•••
••••
••
••
••
CV2T6
CV2T10
CV2T6
CV2T10
••
••
••
••
36" Only
1.800.735.4328 | THERMADOR.COM
137
Page 9
BLOWER OPTIONS AND PRESSURE CURVES
INTEGRATED (MOUNTED ON HOOD)
VTN600CV2C – 600 CFM VTN600F – 600 CFM VTN630C – 600 CFM
VTN1080F – 1000 CFM VTN1000F – 1000 CFM VTN1030C–1000 CFM
138
Page 10
BLOWER OPTIONS AND PRESSURE CURVES
REMOTE (MOUNTED TO ROOF OR EXTERNAL WALL)
VTR630D – 600 CFM VTR1030D – 1000 CFM VTR1330E –1300 CFM
VENTILATION
INLINE (MOUNTED BETWEEN KITCHEN AND EXTERNAL WALL)
VTI610D – 600 CFM VTI1010D – 1000 CFM
NOTE: All measurements are
made with 3 ft. straight duct, 90° bend followed by 1 ft. straight duct. These are NOT free blowing measurements.
1.800.735.4328 | THERMADOR.COM
139
Page 11
EQUIVALENT DUCT LENGTHS FOR COMMONLY USED TRANSITIONS
DUCT PIECE
Smooth Straight
3 1/4" x 10" Straight
3 1/4" x 14" Straight
90° Elbow Round
45° Elbow Round
3 1/4" x 10" 90° Elbow Round
3 1/4" x 10" 45° Elbow Round
3 1/4" x 10" Flat Elbow
Round to 3 1/4" x 10"
3 1/4" x 10" to Round
Round to
1
/4" x 10"
3 90° Elbow
SIZE OF DUCT
PIECE (IN.)
6 1.2
7 0.95
8 0.7
10 0.6
N/A 1
N/A 0.7
612
78
86
65
74
83
N/A 5
N/A 15
N/A 20
61
71
65
73
610
78
EQUIVALENT LENGTH (FT.)
SIZE OF DUCT
DUCT PIECE
3 1/4" x 10" to Round 90° Elbow
3 1/4" x 10" Center Reverse Elbow Left
3 1/4" x 10" Center Reverse Elbow Right
3 1/4" x 10" Left Reverse Elbow
3 1/4" x 10" Right Reverse Elbow
Round Wall Cap
Round Roof Cap
2' Long 3 1/4" x 10" Flex
3 1/4" x 10" to Round
7" Inline Backdraft Damper
3 1/4" x 10" Roof Jack and Shutter
NOTE: These commonly used installation parts can be purchased at a local hardware store. Thermador does not manufacture all these parts.
PIECE (IN.)
610
75
N/A 15
N/A 25
N/A 15
N/A 25
62
72
82
10 2
62
72
82
N/A 20
10 1
7
N/A
EQUIVALENT LENGTH (FT.)
140
Page 12
VENTILATION
HOODS THAT FIT WITH YOUR KITCHEN
When selecting a ventilation system, choose from one of our two sophisticated appliance collections. Select Professional Series for the ultimate in cooking and venting power or the Masterpiece® Series for its sleek styling and numerous convenience functions.
WALL HOODS
Wall hoods offer exceptional, quiet performance and distinctive design options.
• Ef cient, high quality, all stainless steel  lters
• Halogen lighting
• Deep enclosure area for excellent capture
• Removable dishwasher-safe grease collection tray
• Recirculation option at 600 CFM
CHIMNEY WALL HOODS
Our chimney style wall hoods impart a more traditional feel to the kitchen space.
• Adjustable chimney heights suit a range of ceilings
• All stainless steel or stainless steel with glass designs available
• Halogen lighting
VENTILATION
• Dishwasher-safe, stainless steel frame  lters
• Automatic Clean Filter Reminder light
ISLAND HOODS
Thermador Island Hoods offer excellent overall ef ciency in drawing away smoke, moisture and heat.
• An option for when a wall surface is not available
• Dishwasher-safe, stainless steel  lters
• Slim and sleek design that does not obstruct the views beyond your kitchen
• Halogen lighting
• All stainless steel or stainless steel with elegant glass canopy design
CUSTOM INSERTS
To create a seamless design with wall or island applications, use custom hood inserts.
• Available options for all types of cooking surfaces
• User-friendly ventilation controls or remote control options
• Wall or island applications
• Halogen lighting
DOWNDRAFTS
Downdraft ventilation offers space ef ciency and a sleek look for non-professional cooktops.
• Over 13-inch intake
• Full-face  lter combines a  lter with splatter shield in one easy-to-remove, dishwasher-safe element
• Ideal in island applications
• 600 CFM recirculation kit option with integrated blower is available for dif cult-to-duct situations
1.800.735.4328 | THERMADOR.COM 141
Page 13
142
MODELS SHOWN: PH48HS WALL HOOD AND PRG486GDH PRO HARMONY® RANGE AND PA12CVRJ GRIDDLE COVER ACCESSORY
Page 14
VENTILATION
WALL HOODS
VENTILATION — WALL HOODS
Thermador Wall Hoods put the  nishing touch on your cooking system, with deep capture areas for the best overall ef ciency in drawing away smoke, moisture and heat. These elegant hoods combine style with vigorous performance, generating ventilation power from 600 to 1,300 CFM. Available in a variety of heights, widths and depths, they accommodate your individual venting needs. All models include brilliant halogen lighting for enhanced visibility and convenient speed controls. For ultra-simple cleanup, the removable  lters and grease collection trays  t easily in your dishwasher.
1.800.735.4328 | THERMADOR.COM
143
Page 15
WALL HOODS
FEATURES & BENEFITS
HALOGEN LIGHTS
Bright halogen lighting spotlights your best recipes.
DELAYED SHUT-OFF
For the greatest ef ciency, our Professional ventilation models include delayed shut-off to tackle lingering odors. (Except HMWB30FS, HMWB36FS)
POWERFUL VENTILATION
Breathe deeply with the air-freshening power of up to 1,300 CFM. Our new HPWB Series Professional Hood now has blower included for ease of installation.
TIME-TO-CLEAN-FILTER LIGHT
Easy cleanup: all Thermador ventilation  lters are dishwasher-safe, and many hoods feature a built-in Time-to-Clean-Filter reminder light. (Except HMWB30FS, HMWB36FS)
BAFFLE FILTERS
Unique low-pro le, commercial-style baf e  lters maximize grease capture without affecting  ow, and they’re dishwasher-safe for easy cleanup.
EXTERIOR CONTROLS
Easy-to-clean, easy-to-use push­button controls put accuracy at your  ngertips.
KEEP-HOT SHELF
Hold dishes at serving temperature on our optional Keep-Hot Shelf. (Perfect for PH36GS, PH42GS, PH48GS and PH54GS)
PLANNING INFORMATION
MODEL OPTIONS
When selecting a ventilation system, choose from one of our two sophisticated appliance collections. Select Professional Series for the ultimate in cooking and venting power or the Masterpiece® Series for its sleek styling and numerous convenience functions. Thermador Wall Hoods are available in various depths and heights to  t your kitchen plans and are meticulously crafted for both function and design. Be sure to reference the correct model information in this design guide.
ELECTRICAL SPECIFICATIONS
Be sure your Thermador Wall Hood is properly installed and grounded by a quali ed technician. Installation, electrical connections and grounding must comply with all applicable local codes.
Install a suitable conduit box (not furnished). An appropriately­sized, UL-listed conduit connector must be used to correctly attach the conduit to the junction box. Remote blowers require a 5-wire installation.
REQUIRED
MODEL
PH36GS, PH42GS, PH48GS, PH54GS 15 or 20 Amp
PH30HS, PH36HS, PH48HS 15 or 20 Amp
CIRCUIT BREAKER
120V AC, 60 Hz
144
HPWB30FS, HPWB36FS, HPWB48FS 15 or 20 Amp
HMWN30FS, HMWN36FS, HMWN48FS 15 or 20 Amp
HMWB30FS, HMWB36FS 15 or 20 Amp
Page 16
WALL HOODS
PLANNING INFORMATION
VENTILATION — WALL HOODS
INSTALLATION CONSIDERATIONS
The information in this design guide provides key features, product dimensions, cutouts and installation speci cations. Before installing a Thermador Wall Hood, be sure to verify the cutout dimensions and electrical connections. Also, always consult with the installation manual packed with the product for complete details before installing.
Thermador Wall Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
HOOD WIDTH
The hood width should be no less than the width of the cooking surface. Where space is not restricted, a wider hood can be used to increase your capture area.
DISTANCE FROM COOKING SURFACE
Proper mounting height is very important. If a hood is mounted too low, it may be dif cult to cook and be unsafe. If a hood is mounted too high, performance may be compromised. For optimal performance, the distance from the cooking surface to the bottom of the hood should be a minimum of 30", unless otherwise noted. Please refer to the installation manual for each hood and cooktop/range model for proper hood mounting heights.
Remote Blowers (VTR Series) Depending on your preference and ducting situation, these blowers can be mounted on the roof or exterior wall of your home. An exterior installation may be more appealing to reduce noise in the kitchen.
Inline Blowers (VTI series) To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If you have easy access to your duct line (in an attic, for example), this may be an appealing option.
Integrated Blowers (VTN series) These blowers are purchased separately and integrated into the hood or onto the downdraft unit at the time of installation. This option allows you to select your ideal hood with the exact power you require.
CHOOSING THE RIGHT CFM
The power of the cooktop or range, measured in BTU, is perhaps the most important factor in determining CFM needs for a hood. Professional gas cooktops generally should have 1 CFM for every 100 BTU.
You should also consider the cooking space and cooking style of your client.
• More demanding cooks usually require more exhaust capacity to handle moisture generated by boiling large pots of water or the grease and smoke resulting from grilling or frying. This cooking style could require a hood or downdraft system with air ow of 600 to 1,300 CFM.
• For those who are used to preparing quick meals in a relatively small kitchen, a hood with 600 CFM may be adequate ventilation for the cooking space.
AVAILABLE CEILING HEIGHT
The standard ceiling height can vary from region to region and in homes built in different eras. Ceiling heights, even in the same room, can sometimes vary by as much as several inches. Kitchen ceiling heights can vary between 7'6" (or 90") to over 10' (or 120").
Before selecting a Thermador Hood, check the available installation space and any extra space that may remain after proper installation of a hood and cooktop or range. This extra space can be  lled using Thermador’s stainless steel duct cover accessories or integrated with kitchen cabinetry. The space can also be adjusted by raising or lowering your hood within the recommended range (typically 30" to 36" above the cooking surface).
CHOOSING THE CORRECT BLOWER
A variety of interior and exterior blower options (Remote, Inline or Integrated) are available for Thermador’s Professional and Masterpiece® Series Hoods. If the unit you have selected does not have a blower, one can be purchased separately. Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most ef cient air  ow exhaust, use a straight run or as few elbows as possible.
• If the cooking surface is in a peninsula or island, a larger capacity hood can provide better capture when there are cross currents and when the hood needs to be mounted higher. Downdraft ventilation systems are also a good alternative.
• High heat cooking or aromatic foods may require additional CFM. Increasing capture area by 3" on each side is also a recommended way to address this issue.
LENGTH AND SIZE OF DUCTWORK
Do not use  exible duct; it creates back pressure/air turbulence and reduces performance.
Straight runs and gradual turns are best. Use the shortest route with the fewest turns possible.
Proper performance is dependent upon proper ducting. Use a quali ed and trained installer. Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than speci ed CFM of air movement. The speci ed CFM varies from locale to locale. Consult your HVAC professional for speci c requirements in your area.
If using a 10" duct, Thermador recommends not exceeding 150 feet of duct. Transitions, elbows and wall or roof caps are all factors that will add more static pressure, therefore increasing your equivalent duct run.
WARRANTY
Limited warranty parts and labor (2 year)
See page 302 for additional warranty details.
1.800.735.4328 | THERMADOR.COM
145
Page 17
VENTILATION
27-INCH DEPTH WALL HOOD (36"/42"/48"/54")
PH36GS / PH42GS / PH48GS / PH54GS
PH36GS / PH42GS / PH48GS / PH54GS
PERFORMANCE
- Three fan speeds
PROFESSIONAL
PH36GS – 36-Inch
PH42GS – 42-Inch
PH48GS – 48-Inch
PH54GS – 54-Inch
SPECIFICATIONS
Available Hood Widths 36" / 42" / 48" / 54"
UL Approved for Damp Environments
Blower Sold Separately – See
Duct Size at Discharge 10" Round
Ducting Direction Vertical or Horizontal
Dishwasher-safe Filters Commercial-Style Baf e
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Infrared Keep-Hot Lights PAR-38 175W or PAR-40 250W, Included
Electrical 120V AC, 60Hz
Ye s
Blower Options Table
36"– 2 Bulbs 42" / 48" / 54"– 4 Bulbs
2
- Auto function senses heat from the cooking surface and adjusts fan speeds
- Powerfully Quiet
- Extended capture area ensures removal of smoke and odor
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dimmer lighting –for a soft lighting effect
- Two Infrared Keep-Hot Lamps hold food warm until serving time
- Dishwasher-safe stainless steel baf e  lters
- Dishwasher-safe grease collection trays are easily removed
- Filter systems are highly ef cient at capturing grease
- Vertical or horizontal ducting direction
- Seven different blowers to choose from the lineup according to cooking needs
- Choose from Inline, Remote or Integrated Blowers
- Blowers sold separately
- Hood includes  lters, backdraft damper and transition
- Approved by CSA/UL for damp environments
DESIGN
- 27" depth hood is a perfect companion to the Pro Grand Professional Range
- Chiseled design for a seamless integration into any kitchen
- Brushed stainless steel  nish
- Halogen lighting spotlights your best recipes
- Easy-to-view recessed control panel with stainless steel buttons
- Stainless steel professional baf e  lters
®
ventilation systems
146
ACCESSORIES
Keep-Hot Shelf
KHS36QS 36" wide KHS42QS 42" wide KHS48QS 48" wide KHS54QS 54" wide
– Stainless steel  nish – Convenient shelf allows dishes to
keep hot at serving temperature.
– Includes stainless steel backguard
and two shelves.
Duct Cover
Stainless steel duct cover for wall hood applications
Stainless Steel Backsplash
PA36JBS 36" wide PA48JBS 48" wide
Width 6-Inch High 12-Inch High
36-Inch DC36US DCT36US 42-Inch N/A DCT42US 48-Inch DC48US DCT48US
Page 18
VENTILATION
27-INCH DEPTH WALL HOOD (36"/42"/48"/54")
PH36GS / PH42GS / PH48GS / PH54GS
VENTILATION — WALL HOODS
INSTALLATION OPTIONS
Thermador Wall Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop or range can vary. To obtain the necessary installation height above a Thermador Professional Cooktop or Range, consult the appliance‘s installation manual. Accessory 6" and/or 12" tall duct covers are used to  ll the space between the hood and ceiling.
Both vertical and horizontal discharge is possible with either mounting method. The hood is shipped ready for vertical discharge.
BLOWER OPTIONS
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
INLINE
VTI610D – 600 CFM Use WC10 Wall Cap
VTI1010D – 1000 CFM Use WC10 Wall Cap
INTEGRATED
VTN630C – 600 CFM Use WC10 Wall Cap
VTN1030C – 1000 CFM Use WC10 Wall Cap
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
ROOF JACK, WALL CAP & TRANSITION
Roof Jack – RJ310 Wall Cap–WC10 Transition
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
HOOD DIMENSIONS
1.800.735.4328 | THERMADOR.COM
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
INTEGRATED (Mounted on hood)
VTN630C – 600 CFM VTN1030C – 1000 CFM
147
Page 19
VENTILATION
24-INCH DEPTH WALL HOOD (30"/36"/48")
PH30HS / PH36HS / PH48HS
PH30HS / PH36HS / PH48HS
PERFORMANCE
- Three fan speeds
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Filter systems are highly ef cient at capturing grease
PROFESSIONAL
PH30HS – 30-Inch
PH36HS – 36-Inch
PH48HS – 48-Inch
SPECIFICATIONS
Available Hood Widths 30" / 36" / 48"
CSA Approved for Damp Environments
Blower Sold Separately – See
Duct Size at Discharge 10"
Ducting Direction Vertical or Horizontal
Dishwasher-safe Filters Commercial-Style
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60Hz
Ye s
Blower Options Table
Stainless Steel Baf e Filter
30" / 36"– 2 Bulbs 48"– 4 Bulbs
- Dishwasher-safe grease collection trays are easily removed
- Powerfully Quiet
- Blowers sold separately
- Seven different blowers to choose from the lineup according to cooking needs
- Choose from Inline, Remote or Integrated Blowers
- 10" Round duct size
- Vertical or horizontal ducting direction
- Hood includes  lters, backdraft damper and transition
- Approved by CSL for damp environments
DESIGN
- 24" depth hood is 18" tall and a perfect companion with Pro Harmony Ranges and Rangetops
- Chiseled design for a seamless integration into any kitchen
- Brushed stainless steel  nish
- Stainless steel control buttons
- Halogen lighting spotlights your best recipes
- Stainless steel professional style baf e  lters
- Dishwasher-safe stainless steel baf e  lters
- Dimmer lighting –for a soft lighting effect
®
ventilation systems
148
ACCESSORIES
Keep-Hot Shelf
KHS36QS 36" wide KHS42QS 42" wide KHS48QS 48" wide
– Stainless steel  nish – Convenient shelf allows dishes to
keep hot at serving temperature.
– Includes stainless steel backguard
and two shelves.
Duct Cover
Stainless steel duct cover for wall hood applications
Stainless Steel Backsplash
PA30JBS 30" wide PA36JBS 36" wide PA48JBS 48" wide
Width 6-Inch High 12-Inch High
30-Inch DC30US DCT30US 36-Inch DC36US DCT36US 48-Inch DC48US DCT48US
Page 20
VENTILATION
24-INCH DEPTH WALL HOOD (30"/36"/48")
PH30HS / PH36HS / PH48HS
VENTILATION — WALL HOODS
INSTALLATION OPTIONS
Thermador Wall Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop or range can vary. To obtain the necessary installation height above a Thermador Professional Cooktop or Range, consult the appliance‘s installation manual. Accessory 6" and/or 12" duct covers are used to  ll the space between the hood and ceiling.
Both vertical and horizontal discharge is possible with either mounting method. The hood is shipped ready for vertical discharge.
BLOWER OPTIONS
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
INLINE
VTI610D – 600 CFM
VTI1010D – 1000 CFM
INTEGRATED
VTN630C – 600 CFM Use WC10 Wall Cap
VTN1030C – 1000 CFM Use WC10 Wall Cap
See page 143 for further details.
HOOD DIMENSIONS
ROOF JACK, WALL CAP & TRANSITION
Roof Jack – RJ310 Wall Cap–WC10 Transition
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
1.800.735.4328 | THERMADOR.COM
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
INTEGRATED (Mounted on hood)
VTN630C – 600 CFM VTN1030C – 1000 CFM
149
Page 21
VENTILATION
24-INCH DEPTH WALL HOOD WITH BLOWER (30"/36"/48")
HPWB30FS / HPWB36FS / HPWB48FS
HPWB30FS / HPWB36FS / HPWB48FS
PERFORMANCE
- 600 CFM Integrated Blower included with HPWB30FS; 1,000 CFM Integrated Blower included with HPWB36FS and HPWB48FS
- Recirculation possible with kit RECIRC_ _FS (max 600 CFM)
- Three fan speeds
PROFESSIONAL
HPWB30FS – 30-Inch
HPWB36FS – 36-Inch
HPWB48FS – 48-Inch
SPECIFICATIONS
Available Hood Widths 30" / 36" / 48"
Blower 30"– 600 CFM Blower
Duct Size at Discharge 10" Round
Ducting Direction Vertical
Dishwasher-safe Filters Low-Pro le Baf e
Halogen Lighting 120 Volt, 50 Watt Max., GU10 Base, Not Included
Electrical 120V AC, 60Hz
Included 36"– 1000 CFM Blower Included 48"– 1000 CFM Blower Included
30" / 36"– 2 Bulbs 48"– 3 Bulbs
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Dimmer lighting–for a soft lighting effect
- Filter systems are highly ef cient at capturing grease
- Grease collection trays are easily removed and dishwasher-safe
- Powerfully Quiet
- 10" Round duct size
- Vertical ducting direction
- Hood includes  lters, backdraft damper and transition
- Accessories include: Stainless steel duct covers in 6" or 12" heights
- Replacement charcoal  lters available (CHFILT3036)
DESIGN
- Brushed stainless steel  nish
- Welded, polished seams for a  awless design
- Stainless steel button controls
- Halogen lighting spotlights your best recipes
- Dishwasher-safe low-pro le baf e  lters
®
ventilation systems
150
ACCESSORIES
Duct Cover
Stainless steel duct cover for wall hood applications
Stainless Steel Backsplash
PA30JBS 30" wide PA36JBS 36" wide PA48JBS 48" wide
Width 6-Inch High 12-Inch High
30-Inch DC30US DCT30US 36-Inch DC36US DCT36US 48-Inch DC48US DCT48US
Recirculation Kit for 30" Hood Only
RECIRC30FS 30" wide
– Stainless steel  nish – Perfect for hard to duct installations – Use with 600 CFM blowers only
Replacement Charcoal Filters
CHFILT3036 For use with Recirculation Kit RECIRC_FS
Page 22
VENTILATION
24-INCH DEPTH WALL HOOD WITH BLOWER (30"/36"/48")
HPWB30FS / HPWB36FS / HPWB48FS
VENTILATION — WALL HOODS
INSTALLATION OPTIONS
Thermador Wall Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop or range can vary. To obtain the necessary installation height above a Thermador Professional Cooktop or Range, consult the appliance‘s installation manual. Accessory 6" and/or 12" duct covers are used to  ll the space between the hood and ceiling.
This Thermador Wall Hood can be mounted on a wall or suspended from a cabinet. The cabinet must be structurally joined to the wall studs to support the weight of this hood.
These hoods are designed to be used for vertical discharge. A ductless, recirculation installation is possible with kit RECIRC__FS.
BLOWER PRESSURE CURVES
HPWB30FS HPWB36FS
HOOD DIMENSIONS
HPWB48FS
NOTE: All measurements are made with 3 ft. straight duct, 90° bend and 1 ft.
straight duct at exhaust. These are NOT free blowing measurements.
1.800.735.4328 | THERMADOR.COM
151
Page 23
VENTILATION
WALL HOOD (30"/36"/48")
HMWN30FS / HMWN36FS / HMWN48FS
MASTERPIECE
HMWN30FS – 30-Inch
HMWN36FS – 36-Inch
HMWN48FS – 48-Inch
SPECIFICATIONS
Available Hood Widths 30" / 36" / 48"
Blower Sold separately –
Duct Size at Discharge 10" Round
Ducting Direction Vertical
Dishwasher-safe Filters Low-Pro le Baf e Halogen Lighting
120 Volt, 50 Watt Max., GU10 Base, Not Included
Electrical 120V AC, 60Hz
See Blower Options table
30" / 36"– 2 Bulbs 48"– 3 Bulbs
HMWN30FS / HMWN36FS / HMWN48FS
PERFORMANCE
- Recirculation possible with kit RECIRC_ _FS (max 600 CFM)
- Three fan speeds plus 10 minute high-power operation mode
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe low-pro le baf e  lters
- Grease collection trays are easily removed and dishwasher-safe
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- 10" Round duct size
- Vertical ducting direction
- Hood includes  lters, lights, backdraft damper and transition
- Blowers sold separately
- Choose from Inline, Remote or Integrated Blowers
- Accessories include: Stainless steel duct covers in 6" or 12" heights
- Replacement charcoal  lters available (CHFILT3036)
DESIGN
- Brushed stainless steel  nish
- Welded, polished seams for a  awless design
- Premium electronic touch controls
- Halogen lighting spotlights your best recipes
®
ventilation systems
152
ACCESSORIES
Duct Cover
Stainless steel duct cover for wall hood applications
Stainless Steel Backsplash
PA30JBS 30" wide PA36JBS 36" wide PA48JBS 48" wide
Width 6-Inch High 12-Inch High
30-Inch DC30US DCT30US 36-Inch DC36US DCT36US 48-Inch DC48US DCT48US
Recirculation Kit
RECIRC30FS 30" wide RECIRC36FS 36" wide
– Stainless steel  nish – Perfect for hard to duct installations – Use with 600 CFM blowers only
Replacement Charcoal Filters
CHFILT3036 For use with Recirculation Kit RECIRC_FS
Page 24
VENTILATION
WALL HOOD (30"/36"/48")
HMWN30FS / HMWN36FS / HMWN48FS
VENTILATION — WALL HOODS
INSTALLATION OPTIONS
Thermador Wall Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop or range can vary. To obtain the necessary installation height above a Thermador Professional Cooktop or Range, consult the appliance‘s installation manual. Accessory 6" and/or 12" duct covers are used to  ll the space between the hood and ceiling.
This Thermador Wall Hood can be mounted on a wall or suspended from a cabinet. The cabinet must be structurally joined to the wall studs to support the weight of this hood.
These hoods are designed to be used for vertical discharge. A ductless, recirculation installation is possible with kit RECIRC__FS.
These hoods are not recommended to be used over indoor grills.
BLOWER OPTIONS
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
INLINE
VTI610D – 600 CFM
VTI1010D – 1000 CFM
INTEGRATED
VTN600F – 600 CFM
VTN1000F – 1000 CFM Not for use with 30" hood
See page 143 for further details.
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
HOOD DIMENSIONS
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
1.800.735.4328 | THERMADOR.COM
INTEGRATED (Mounted on hood)
VTN600F – 600 CFM VTN1000F – 1000 CFM
153
Page 25
VENTILATION
WALL HOOD WITH BLOWER (30"/36")
HMWB30FS / HMWB36FS
HMWB30FS / HMWB36FS
PERFORMANCE
- 600 CFM Integrated Blower included
- Recirculation possible with kit RECIRC_ _FS (max 600 CFM)
- Three fan speeds plus 10 minute high-power operation mode
MASTERPIECE
HMWB30FS – 30-Inch
HMWB36FS – 36-Inch
SPECIFICATIONS
Available Hood Widths 30" / 36" Blower 600 CFM Blower Included
Duct Size at Discharge 10" Round
Ducting Direction Vertical
Dishwasher-safe Filters Low-Pro le Baf e
Halogen Lighting 120 Volt, 50 Watt Max., GU10 Base, Not Included
Electrical 120V AC, 60Hz
2 Bulbs
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe low-pro le baf e  lters
- Grease collection trays are easily removed and dishwasher-safe
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- 10" Round duct size
- Vertical ducting direction
- Hood includes  lters, lights, backdraft damper and transition
- Accessories include: Stainless steel duct covers in 6" or 12" heights
- Replacement charcoal  lters available (CHFILT3036)
DESIGN
- Brushed stainless steel  nish
- Welded, polished seams for a  awless design
- Easy-to-operate control buttons
- Halogen lighting spotlights your best recipes
®
ventilation systems
154
ACCESSORIES
Duct Cover
Stainless steel duct cover for wall hood applications
Stainless Steel Backsplash
PA30JBS 30" wide PA36JBS 36" wide
Width 6-Inch High 12-Inch High
30-Inch DC30US DCT30US 36-Inch DC36US DCT36US 48-Inch DC48US DCT48US
Recirculation Kit
RECIRC30FS 30" wide RECIRC36FS 36" wide
– Stainless steel  nish – Perfect for hard to duct installations – Use with 600 CFM blowers only
Replacement Charcoal Filters
CHFILT3036 For use with Recirculation Kit RECIRC_FS
Page 26
VENTILATION
WALL HOOD WITH BLOWER (30"/36")
HMWB30FS / HMWB36FS
VENTILATION — WALL HOODS
INSTALLATION OPTIONS
Thermador Wall Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop or range can vary. To obtain the necessary installation height above a Thermador Professional Cooktop or Range, consult the appliance‘s installation manual. Accessory 6" and/or 12" duct covers are used to  ll the space between the hood and ceiling.
This Thermador Wall Hood can be mounted on a wall or suspended from a cabinet. The cabinet must be structurally joined to the wall studs to support the weight of this hood.
These hoods are designed to be used for vertical discharge. A ductless, recirculation installation is possible with kit RECIRC__FS.
These hoods are not recommended to be used over indoor grills.
BLOWER PRESSURE CURVES
HMWB30FS
HOOD DIMENSIONS
HMWB36FS
NOTE: All measurements are made with 3 ft. straight duct,
90° bend and 1 ft. straight duct at exhaust. These are NOT free blowing measurements.
1.800.735.4328 | THERMADOR.COM 155
Page 27
156
MODELS SHOWN: HDDW36FS CHIMNEY WALL DRAWER HOOD, SGSX365FS GAS COOKTOP AND MED301JS BUILT-IN OVEN
Page 28
VENTILATION
CHIMNEY WALL
VENTILATION — CHIMNEY WALL HOODS
HOODS
Our Masterpiece® Series chimney style wall hoods impart a more traditional feel to the kitchen space and create a dramatic gathering point. Each model is adjustable to suit a range of ceiling heights and includes conveniences such as dishwasher-safe, anodized  lters and electronic 4-speed controls. Halogen lighting brilliantly illuminates your cooking space for excellent visibility.
1.800.735.4328 | THERMADOR.COM 157
Page 29
CHIMNEY WALL HOODS
FEATURES & BENEFITS
HALOGEN LIGHTS
Bright halogen lighting spotlights your best recipes.
MESH FILTERS
Aluminum mesh  lters with stainless steel frame maximize grease capture without affecting  ow and feature a quick release latch for easy cleanup.
PLANNING INFORMATION
MODEL OPTIONS
Thermador Masterpiece Series Chimney Wall Hoods feature sleek styling and numerous convenience functions. Chimney Wall Hoods are available in 36-inch and 42-inch widths and are adjustable to suit a range of ceiling heights. All stainless steel or stainless steel with glass designs are available. Be sure to reference the correct model information in this design guide.
ELECTRICAL SPECIFICATIONS
Be sure your Thermador Chimney Wall Hood is properly installed and grounded by a quali ed technician. Installation, electrical connections and grounding must comply with all applicable local codes.
If possible, site the earthed socket directly behind the chimney paneling. The grounded socket should be connected via its own circuit. If the grounded socket is no longer accessible following installation of the hood, ensure that there is a permanently installed disconnector.
REQUIRED
MODEL
HMCN36FS, HMCN42FS, HMCB36FS, HMCB42FS, HGEW36FS, HDDW36FS
CIRCUIT BREAKER
120V AC, 60 Hz
15 Amp
INSTALLATION CONSIDERATIONS
The information in this design guide provides key features, product dimensions, cutouts and installation speci cations. Before installing a Thermador Chimney Wall Hood, be sure to verify the cutout dimensions and electrical connections. Also, always consult with the installation manual packed with the product for complete details before installing.
158
ELECTRONIC TOUCH CONTROL
The sleek electronic touch control panel is easy-to-use and easy-to-clean.
TIME-TO-CLEAN-FILTER LIGHT
Easy cleanup: All Thermador ventilation  lters are dishwasher-safe, and many hoods feature a built-in Time-to-Clean-Filter reminder light. (Except HMCB36FS, HMCB42FS)
DELAYED SHUT-OFF
For the greatest ef ciency, our Masterpiece models include delayed shut-off to tackle lingering odors. (Except HMCB36FS, HMCB42FS)
®
ventilation
Thermador Chimney Wall Hoods may be installed above a Thermador non-professional gas, electric, or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
DISTANCE FROM COOKING SURFACE
Proper mounting height is very important. If a hood is mounted too low, it may be dif cult to cook and be unsafe. If a hood is mounted too high, performance may be compromised.
For optimal performance, the distance from the cooking surface to the bottom of the hood should be a minimum of 30", unless otherwise noted. Please refer to the installation manual for each hood and cooktop/range model for proper hood mounting heights.
HOOD WIDTH
The hood width should be no less than the width of the cooking surface. Where space is not restricted, a wider hood can be used to increase your capture area.
Page 30
CHIMNEY WALL HOODS
PLANNING INFORMATION
VENTILATION — CHIMNEY WALL HOODS
AVAILABLE CEILING HEIGHT
The standard ceiling height can vary from region to region and in homes built in different eras. Ceiling heights, even in the same room, can sometimes vary by as much as several inches. Kitchen ceiling heights can vary between 7'6" (or 90") to over 10' (or 120").
Before selecting your hood, check your available installation space and any extra space that may remain after proper installation of your hood and cooktop or range. This extra space can be  lled using Thermador‘s Stainless Steel Duct Cover or Chimney Extension Accessories. The space can also be adjusted by raising or lowering your hood within the recommended range (typically 30" to 36" above the cooking surface).
CHOOSING THE CORRECT BLOWER
A variety of interior and exterior blower options (Remote, Inline or Integrated) are available for Thermador’s Professional and Masterpiece® Series Hoods. If the unit you have selected does not have a blower included, one can be purchased separately. Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most ef cient air  ow exhaust, use a straight run or as few elbows as possible.
Remote Blowers (VTR Series) Depending on your preference and ducting situation, these blowers can be mounted on the roof or exterior wall of your home. An exterior installation may be more appealing to reduce noise in the kitchen.
Inline Blowers (VTI series) To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If you have easy access to your duct line (in an attic, for example), this may be an appealing option.
Integrated Blowers (VTN series) These blowers are purchased separately and integrated into the hood or onto the downdraft unit at the time of installation. This option allows you to select your ideal hood with the exact power you require.
SPECIAL NOTE: Always allow access to the blower for serviceability, should it be needed.
CHOOSING THE RIGHT CFM
The power of the cooktop or range, measured in BTU, is perhaps the most important factor in determining CFM needs for a hood. Professional gas cooktops generally should have 1 CFM for every 100 BTU. For Masterpiece Electric and Induction Cooktops, and Gas Cooktops under 60,000 BTU, choose a blower with a minimum of 100 CFM per 12" of cooktop width.
You should also consider the cooking space and cooking style of your client.
• More demanding cooks usually require more exhaust capacity to handle moisture generated by boiling large pots of water or the grease and smoke resulting from grilling or frying. This cooking style could require a hood or downdraft system with air ow of 600 to 1,300 CFM.
• High heat cooking or aromatic foods may require additional CFM. Increasing capture area by 3" on each side is also a recommended way to address this issue.
• For those who are used to preparing quick meals in a relatively small kitchen, a hood with 400 to 600 CFM may be adequate ventilation for the cooking space.
• If the cooking surface is in a peninsula or island, a larger capacity hood can provide better capture when there are cross currents and when the hood needs to be mounted higher. Downdraft ventilation systems are also a good alternative.
LENGTH AND SIZE OF DUCTWORK
Proper performance is dependent upon proper ducting. Use a quali ed and trained installer.
Do not use  exible duct; it creates back pressure/air turbulence and reduces performance.
Straight runs and gradual turns are best. Use the shortest route with the fewest turns possible.
Local building codes may require the use of makeup air systems when using ducted ventilation systems greater than speci ed CFM of air movement. The speci ed CFM varies from locale to locale. Consult your HVAC professional for speci c requirements in your area.
If using a 10" duct, Thermador recommends not exceeding 150 feet of duct. Transitions, elbows and wall or roof caps are all factors that will add more static pressure, therefore increasing your equivalent duct run.
WARRANTY
Limited warranty parts and labor (2 year)
See page 302 for additional warranty details.
1.800.735.4328 | THERMADOR.COM 159
Page 31
VENTILATION
CHIMNEY WALL HOOD (36"/42")
HMCN36FS / HMCN42FS
HMCN36FS / HMCN42FS
PERFORMANCE
- Three fan speeds plus 10 minute high-power operation mode
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Dimmer lighting – for those hours after a late meal
- Dishwasher-safe stainless-frame mesh  lters
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- Vertical ducting direction
- 8" Round duct size
- Telescopic chimney –adjustable at installation
- Blowers sold separately
- Choose from Inline, Remote or Integrated Blowers
®
ventilation systems
MASTERPIECE
HMCN36FS – 36-Inch
HMCN42FS – 42-Inch
SPECIFICATIONS
Available Hood Widths 36" / 42"
Blower Sold Separately —
Duct Size at Discharge 8" Round
Ducting Direction Vertical
Ceiling Heights 8' 2" ft. to 9 ft.
Dishwasher-safe Filters 3 Mesh with
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical
See Blower Options Table
Stainless-Frame
3 Bulbs
120V AC, 60Hz
DESIGN
- Brushed stainless steel  nish
- Welded, polished seams for a  awless design
- Premium electronic touch controls
- Halogen lighting spotlights your best recipes
160
ACCESSORIES
Chimney Extension
CHIMXHMC Stainless steel chimney hood extension for up to 11-foot ceiling applications. Extension replaces upper section of standard chimney extension.
Page 32
VENTILATION
CHIMNEY WALL HOOD (36"/42")
HMCN36FS / HMCN42FS
VENTILATION — CHIMNEY WALL HOODS
INSTALLATION OPTIONS
Thermador Chimney Wall Hoods may be installed above a Thermador non-professional gas, electric, or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. To obtain the necessary installation height above a Thermador non-professional gas, electric, or induction cooktop, consult the appliance’s installation manual.
Thermador Chimney Wall Hoods must be mounted on a wall.
These hoods are designed to be used for vertical discharge. The HMCN_FS hood offers the  exibility to choose a blower from our lineup to  t your installation needs. All other chimney wall hoods have the convenience of integrated blowers.
BLOWER OPTIONS
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
INLINE
VTI610D – 600 CFM
VTI1010D – 1000 CFM
INTEGRATED
VTN1080F – 1000 CFM
See page 157 for further details.
HOOD DIMENSIONS
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
1.800.735.4328 | THERMADOR.COM
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
INTEGRATED (Mounted on hood)
VTN1080F – 1000 CFM
161
Page 33
VENTILATION
CHIMNEY WALL HOOD WITH BLOWER (36"/42")
HMCB36FS / HMCB42FS
HMCB36FS / HMCB42FS
PERFORMANCE
- 600 CFM Integrated Blower included
- Three fan speeds plus 10 minute high-power operation mode
- Dishwasher-safe stainless-frame mesh  lters
MASTERPIECE
HMCB36FS – 36-Inch
HMCB42FS – 42-Inch
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- 6" Round duct size
- Vertical ducting direction
- Telescopic chimney –adjustable at installation
- Hood includes  lters, lights, backdraft damper and transition
DESIGN
- Brushed stainless steel  nish
- Welded, polished seams for a  awless design
- Easy-to-operate control buttons
- Halogen lighting spotlights your best recipes
®
ventilation systems
SPECIFICATIONS
Available Hood Widths 36" / 42" Blower 600 CFM Blower Included
Duct Size at Discharge 6" Round
Ducting Direction Vertical
Ceiling Heights 8' 2" ft. to 9 ft.
Dishwasher-safe Filters 3 Mesh with
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60Hz
Stainless-Frame
3 Bulbs
ACCESSORIES
Chimney Extension
CHIMXHMC Stainless steel chimney hood extension for up to 11-foot ceiling applications. Extension replaces upper section of standard chimney extension.
162
Page 34
VENTILATION
CHIMNEY WALL HOOD WITH BLOWER (36"/42")
HMCB36FS / HMCB42FS
VENTILATION — CHIMNEY WALL HOODS
INSTALLATION OPTIONS
Thermador Chimney Wall Hoods may be installed above a Thermador non-professional gas, electric, or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. To obtain the necessary installation height above a Thermador non­professional gas, electric, or induction cooktop, consult the appliance’s installation manual.
Thermador Chimney Wall Hoods must be mounted on a wall.
These hoods are designed to be used for vertical discharge. A 600 CFM integrated blower is included.
BLOWER PRESSURE CURVES
HMCB36FS
HOOD DIMENSIONS
HMCB42FS
NOTE: All measurements are made with 3 ft. straight duct,
90° bend and 1 ft. straight duct at exhaust. These are NOT free blowing measurements.
1.800.735.4328 | THERMADOR.COM
163
Page 35
VENTILATION
CHIMNEY WALL DRAWER HOOD (36")
HDDW36FS
HDDW36FS
INNOVATION
- Unique sliding stainless canopy can be pushed back against the wall for increased head room
- 45% increase in capture area when hood is extended
PERFORMANCE
- 600 CFM Integrated Blower included
- Three fan speeds plus 10 minute high-power operation mode
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours
MASTERPIECE
HDDW36FS – 36-Inch
of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dimmer lighting – for those hours after a late meal
- Dishwasher-safe stainless-frame mesh  lters
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- Sound insulation mats make this hood barely audible
- 6" Round duct size
- Vertical ducting direction
- Telescopic chimney –adjustable at installation
- Hood includes  lters, backdraft damper and transition
®
ventilation systems
SPECIFICATIONS
Available Hood Widths 36" Blower 600 CFM Blower Included
Duct Size at Discharge 6" Round
Ducting Direction Vertical
Ceiling Heights 7
Dishwasher-safe Filters 4 Mesh with
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical
3
/4 ft. to 9 1/2 ft.
Stainless-Frame
4 Bulbs
120V AC, 60Hz
ACCESSORIES
Chimney Extension
DESIGN
- Brushed stainless steel  nish
- Welded, polished seams for a  awless design
- Premium electronic touch controls
- Halogen lighting spotlights your best recipes
THERMADOR EXCLUSIVE
164
CHIMXHDD Stainless steel chimney hood extension for up to 11-foot ceiling applications. Extension replaces upper section of standard chimney extension.
Page 36
CHIMNEY WALL DRAWER HOOD (36")
INSTALLATION OPTIONS
Thermador Chimney Wall Hoods may be installed above a Thermador non-professional gas, electric, or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. To obtain the necessary installation height above a Thermador non­professional gas, electric, or induction cooktop, consult the appliance’s installation manual.
Thermador Chimney Wall Hoods must be mounted on a wall.
These hoods are designed to be used for vertical discharge. A 600 CFM integrated blower is included.
BLOWER PRESSURE CURVES
HDDW36FS
VENTILATION
HDDW36FS
INSTALLATION NOTE: This product ships with two
transport brackets to hold the moveable canopy in place during shipping and installation. After installation, be sure to remove the brackets to operate the sliding drawer canopy.
VENTILATION — CHIMNEY WALL HOODS
VENTILATION — CHIMNEY WALL HOODS
NOTE: All measurements are made with 3 ft. straight duct,
90° bend and 1 ft. straight duct at exhaust. These are NOT free blowing measurements.
1.800.735.4328 | THERMADOR.COM
165
Page 37
MODELS SHOWN: HMIB40HS ISLAND HOOD AND CIT365KB INDUCTION COOKTOP166
Page 38
VENTILATION
ISLAND HOODS
VENTILATION — ISLAND HOODS
Thermador Island Hoods put the  nishing touches on your cooking system, with excellent overall ef ciency in drawing away smoke, moisture and heat. The adjustable chimney height is perfect over island cooktop or range installations. Dishwasher-safe  lters make cleanup easy.
1.800.735.4328 | THERMADOR.COM
167
Page 39
ISLAND HOODS
FEATURES & BENEFITS
PLANNING INFORMATION
MODEL OPTIONS
Thermador Professional Series Island Hoods are available in 42-inch and 48-inch widths and feature a stainless steel design. Masterpiece® Series Island Hoods are available in a 40-inch, 42-inch and 48-inch widths and feature a stainless steel design and the 40-inch has an elegant glass canopy. All of our island hoods are adjustable to suit ceiling heights of up to 9 feet.
ELECTRICAL SPECIFICATIONS
Be sure your Thermador Wall Hood is properly installed and grounded by a quali ed technician. Installation, electrical connections and grounding must comply with all applicable local codes.
REQUIRED
MODEL
HPIN42HS, HPIN48HS HPIB42HS, HPIB48HS HMIB40HS
CIRCUIT BREAKER
120V AC, 60 Hz
Max 10 Amp
EXTERIOR CONTROLS
Easy-to-clean, easy-to-use push-button controls put accuracy at your  ngertips.
POWERFULLY QUIET® OPERATION
Steam, smoke and odors are no problem for Thermador‘s ducted ventilation systems.
TIME-TO-CLEAN-FILTER LIGHT
Easy cleanup: All Thermador ventilation  lters are dishwasher-safe, and many hoods feature a built-in Time-to-Clean-Filter reminder light.
DISHWASHER-SAFE FILTERS
Dishwasher-safe aluminum  lters for easy-clean maintenance.
DELAYED SHUT-OFF
For the greatest ef ciency, our Professional and Masterpiece® ventilation models include delayed shut-off to tackle lingering odors.
HALOGEN LIGHTS
Bright halogen lighting spotlights your best recipes.
INSTALLATION CONSIDERATIONS
The information in this design guide provides key features, product dimensions and installation speci cations. Before installing a Thermador Island Hood, be sure to verify the dimensions and electrical connections. Also, always consult with the installation manual packed with the product for complete details before installing.
Thermador Island Hoods may be installed above a Thermador Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
HOOD WIDTH
The hood width should be no less than the width of the cooking surface. Where space is not restricted, a wider hood can be used to increase your capture area. Island installations require a greater capture area; therefore the hoods used should overlap your cooking surface by a minimum of 3" to 6" on either side.
DISTANCE FROM COOKING SURFACE
Proper mounting height is very important. If a hood is mounted too low, it may be dif cult to cook and be unsafe. If a hood is mounted too high, performance may be compromised. For optimal performance, the distance from the cooking surface to the bottom of the hood should be a minimum of 30", unless otherwise noted. Please refer to the installation manual for each hood and cooktop/range model for proper hood mounting heights.
168
Page 40
ISLAND HOODS
PLANNING INFORMATION
VENTILATION — ISLAND HOODS
AVAILABLE CEILING HEIGHT
The standard ceiling height can vary from region to region and in homes built in different eras. Ceiling heights, even in the same room, can sometimes vary by as much as several inches. Kitchen ceiling heights can vary between 7'6" (or 90") to over 10' (or 120").
Before selecting a Thermador Hood, check the available installation space and any extra space that may remain after proper installation of a hood and cooktop or range. This extra space can be  lled using Thermador’s stainless steel duct cover accessories. The space can also be adjusted by raising or lowering your hood within the recommended range (typically 30" to 36" above the cooking surface).
CHOOSING THE CORRECT BLOWER
A variety of interior and exterior blower options (Remote or Inline) are available for Thermador’s Professional Series Island Hoods. If the unit you have selected does not have a blower, one can be purchased separately. Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most ef cient air  ow exhaust, use a straight run or as few elbows as possible.
Remote Blowers (VTR Series) Depending on your preference and ducting situation, these blowers can be mounted on the roof or exterior wall of your home. An exterior installation may be more appealing to reduce noise in the kitchen.
Inline Blowers (VTI Series) To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If you have easy access to your duct line (in an attic, for example), this may be an appealing option.
CHOOSING THE RIGHT CFM
The power of the cooktop or range, measured in BTU, is perhaps the most important factor in determining CFM needs for a hood. Professional Gas Cooktops generally should have 1 CFM for every 100 BTU. For Masterpiece® Electric and Induction Cooktops, and Gas Cooktops under 60,000 BTU, choose a blower with a minimum of 100 CFM per 12" of cooktop width.
You should also consider the cooking space and cooking style of your client.
• More demanding cooks usually require more exhaust capacity to handle moisture generated by boiling large pots of water or the grease and smoke resulting from grilling or frying. This cooking style could require a hood or downdraft system with air ow of 600 to 1,300 CFM.
• For those who are used to preparing quick meals in a relatively small kitchen, a hood with 400 to 600 CFM may be adequate ventilation for the cooking space.
• If the cooking surface is in a peninsula or island, a larger capacity hood can provide better capture when there are cross currents and when the hood needs to be mounted higher. Downdraft ventilation systems are also a good alternative.
• High heat cooking or aromatic foods may require additional CFM. Increasing capture area by 3" on each side is also a recommended way to address this issue.
LENGTH AND SIZE OF DUCTWORK
Do not use  exible duct; it creates back pressure/air turbulence and reduces performance.
Straight runs and gradual turns are best. Use the shortest route with the fewest turns possible.
Proper performance is dependent upon proper ducting. Use a quali ed and trained installer. Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than speci ed CFM of air movement. The speci ed CFM varies from locale to locale. Consult your HVAC professional for speci c requirements in your area.
If using a 10" duct, Thermador recommends not exceeding 150 feet of duct. Transitions, elbows and wall or roof caps are all factors that will add more static pressure, therefore increasing your equivalent duct run.
1.800.735.4328 | THERMADOR.COM
WARRANTY
Limited warranty parts and labor (2 year)
See page 302 for additional warranty details.
169
Page 41
VENTILATION
LOW PROFILE ISLAND HOOD (42"/48")
HPIN42HS / HPIN48HS
HPIN42HS / HPIN48HS
PERFORMANCE
- Three fan speeds
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe frameless  lters with stainless steel covers
- Filter systems are highly ef cient at capturing grease
PROFESSIONAL
HPIN42HS – 42-Inch
HPIN48HS – 48-Inch
SPECIFICATIONS
Available Hood Widths 42" / 48"
Blower Sold Separately —
Duct Size at Discharge 6" Round
Ducting Direction Vertical
Ceiling Heights 8' 2" ft. to 9 ft.
Dishwasher-safe Filters Stainless Steel Filter
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60 Hz
See Blower Options Table
4 Bulbs
- Powerfully Quiet
- Vertical ducting direction
- 6" round duct size
- Blowers sold separately
DESIGN
- Sleek appearance does not obstruct views beyond the kitchen
- Chiseled design for a seamless integration into any kitchen
- Halogen lighting spotlights your best recipes
- Brushed stainless steel  nish
- Stainless steel control buttons
®
ventilation systems
170
Page 42
VENTILATION
LOW PROFILE ISLAND HOOD (42"/48")
HPIN42HS / HPIN48HS
VENTILATION — ISLAND HOODS
INSTALLATION OPTIONS
Thermador Professional Series Island Hoods may be installed above a Thermador Professional Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. To obtain the necessary installation height above a Thermador Cooktop or Range, consult the appliance‘s installation manual.
Thermador Island Hoods are suspended from the ceiling. These hoods are designed to be used for vertical discharge. A blower must be purchased separately.
BLOWER OPTIONS
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
INLINE
VTI610D – 600 CFM
VTI1010D – 1000 CFM
See page 167 for further details.
HOOD DIMENSIONS
31 3/16"
7
/16"
41
792
1052
31 3/16"
7
/16"
41
792
1052
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
1.800.735.4328 | THERMADOR.COM
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
171
Page 43
VENTILATION
LOW PROFILE ISLAND HOOD WITH BLOWER (42"/48")
HPIB42HS / HPIB48HS
HPIB42HS / HPIB48HS
PERFORMANCE
- 600 CFM Integrated Blower included
- Recirculation possible with kit RECIRISL
- Three fan speeds
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe frameless  lters with stainless steel covers
MASTERPIECE
HPIB42HS – 42-Inch
HPIB48HS – 48-Inch
SPECIFICATIONS
Available Hood Widths 42" / 48" Blower 600 CFM Blower Included
Duct Size at Discharge 6" Round
Ducting Direction Vertical
Ceiling Heights 8' 2" ft. to 9 ft.
Dishwasher-safe Filters Stainless Steel Filter
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60 Hz
4 Bulbs
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- 6" Round duct size
- Vertical ducting direction
- All-in-one solution with an integrated blower included
- Hood includes  lters, backdraft damper and transition
- Replacement charcoal  lters available (CHFILISL)
DESIGN
- Sleek appearance does not obstruct views beyond the kitchen
- Brushed stainless steel  nish
- Chiseled design for a seamless integration into any kitchen
- Halogen lighting spotlights your best recipes
- Stainless steel control buttons
®
ventilation systems
172
ACCESSORIES
Island Hood Recirculation Kit
RECIRISL
- Stainless steel  nish
- Perfect for hard to duct installations
- Use with 600 CFM blowers only
Replacement Charcoal Filters
CHFILISL For use with Recirculation Kit RECIRISL
Page 44
VENTILATION
LOW PROFILE ISLAND HOOD WITH BLOWER (42"/48")
HPIB42HS / HPIB48HS
VENTILATION — ISLAND HOODS
INSTALLATION OPTIONS
Thermador Masterpiece® Series Island Hoods may be installed above a Thermador non-professional gas, electric, or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. To obtain the necessary installation height above a Thermador Cooktop or Range, consult the appliance‘s installation manual.
Thermador Island Hoods are suspended from the ceiling. These hoods are designed to be used for vertical discharge. A 600 CFM blower is included.
Thermador duct covers are designed for universal application.
In recirculation mode the louvers should be towards the ceiling for exhaust air to escape in the kitchen.
In ducted mode, the same duct cover can be turned upside down to hide away the louvers behind the lower duct cover piece.
BLOWER PRESSURE CURVES
HPIB42HS
EXTERNAL EXHAUST
31 3/16"
7
41
/16"
792
1052
31 3/16"
7
/16"
41
792
1052
HPIB48HS
NOTE: All measurements are made with 3 ft. straight duct,
90° bend and 1 ft. straight duct at exhaust. These are NOT free blowing measurements.
INTERNAL RECIRCULATION
31 3/16"
7
/16"
41
792
1052
31 3/16"
7
/16"
41
792
1052
1.800.735.4328 | THERMADOR.COM
173
Page 45
VENTILATION
GLASS ISLAND HOOD WITH BLOWER (40")
HMIB40HS
HMIB40HS
PERFORMANCE
- 600 CFM Integrated Blower included
- An ideal solution for island cooktop installations
- Four fan speeds including one intensive level
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dimmer lighting – for a soft lighting effect completely adjustable by user
- Dishwasher-safe stainless steel mesh  lters
MASTERPIECE
HMIB40HS – 40-Inch
SPECIFICATIONS
Available Hood Width 40" Blower 600 CFM Blower Included
Duct Size at Discharge 6" Round
Ducting Direction Vertical
Ceiling Heights 8' 2" ft. to 9 ft.
Dishwasher-safe Filters Stainless Steel Mesh Filter
Halogen Lighting 12 Volt, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60 Hz
4 Bulbs
- Filter systems are highly ef cient at capturing grease
- Easy-to-operate control buttons
- Powerfully Quiet
- Perfect  t for 30" & 36" cooktops
- 6" Round duct size
- Vertical ducting direction
DESIGN
- Stunning combination of glass and stainless steel with Masterpiece® design elements
- Chiseled design for a seamless integration into any kitchen
- Halogen lighting spotlights your best recipes
- Brushed stainless steel  nish
- Premium electronic touch controls
®
ventilation systems
174
ACCESSORIES
Island Hood Recirculation Kit
RECIRISL
- Stainless steel  nish
- Perfect for hard to duct installations
- Use with 600 CFM blowers only
Replacement Charcoal Filters
CHFILISL For use with Recirculation Kit RECIRISL
Page 46
VENTILATION
GLASS ISLAND HOOD WITH BLOWER (40")
HMIB40HS
VENTILATION — ISLAND HOODS
VENTILATION — ISLAND HOODS
INSTALLATION OPTIONS
Thermador Masterpiece® Series Island Hoods may be installed above a Thermador non-professional gas, electric, or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. To obtain the necessary installation height above a Thermador Cooktop or Range, consult the appliance‘s installation manual.
Thermador Island Hoods are suspended from the ceiling. These hoods are designed to be used for vertical discharge. A 600 CFM blower is included.
BLOWER PRESSURE CURVES
HMIB40HS
EXTERNAL EXHAUST
31 3/16"
7
41
/16"
792
1052
INTERNAL RECIRCULATION
31 3/16"
7
/16"
41
792
1052
NOTE: All measurements are made with 3 ft. straight duct, 90° bend and 1 ft. straight duct at exhaust. These are NOT free blowing measurements.
1.800.735.4328 | THERMADOR.COM
175
Page 47
MODELS SHOWN: VCI248DS PROFESSIONAL SERIES CUSTOM INSERT176
Page 48
VENTILATION
CUSTOM INSERTS
VENTILATION — CUSTOM INSERTS
Use Thermador Custom Hood Inserts within custom hood applications to create a seamless design with wall or island applications. These inserts ef ciently and quietly remove odor and steam with easy-to-access controls. Inserts are available for both professional and non­professional applications.
1.800.735.4328 | THERMADOR.COM
177
Page 49
CUSTOM INSERTS
FEATURES & BENEFITS
REMOTE VENTILATION CONTROL
Remote controls for customized ventilation applications are easy to use and have a sophisticated and professional style. (photo represents VCI2REMFS)
MESH FILTERS
Aluminum mesh  lters with stainless steel frame maximize grease capture without affecting  ow. (VCI230DS, VCI236DS, VCI248DS only)
BAFFLE FILTERS
Stainless steel commercial-style baf e  lters maximize grease
capture and they're dishwasher safe for easy clean-up. (VCIN and VCIB Series)
HALOGEN LIGHTS
Bright halogen lighting spotlights your best recipes.
CUSTOM HOOD INSERT
Specially designed for professional custom hood applications to create a concealed ventilation system.
TIME-TO-CLEAN-FILTER LIGHT
Easy cleanup: All Thermador ventilation  lters are dishwasher-safe, and feature a built-in Time-to-Clean-Filter reminder light.
DELAYED SHUT-OFF
For the greatest ef ciency, our Professional ventilation models include delayed shut-off to tackle lingering odors.
PUSH BUTTON CONTROLS
Concealed three-speed, push-button controls are easy to use.
BAFFLE FILTERS
The commercial style baf e  lters make high-grease cooking easy. The dishwasher-safe  lters are stainless steel.
PLANNING INFORMATION
MODEL OPTIONS
Thermador Custom Hood Inserts are available for both professional and non-professional applications. The Professional Series Custom Hood Inserts are available in 30-inch, 36-inch, 48-inch, and 54-inch widths. The Masterpiece® Series Custom Hood Inserts are available in 21-inch (for 30-inch wide installations) and 29-inch (for 36-inch wide installations), 30-inch, 36-inch, and 48-inch widths.
ELECTRICAL SPECIFICATIONS
Be sure your Thermador Custom Insert is properly installed and grounded by a quali ed technician. Installation, electrical connections and grounding must comply with all applicable local codes.
REQUIRED
MODEL
VCIN36JP, VCIB36JP, VCIN48JP, VCIB48JP, VCIN54JP, VCIB54JP, VCI230DS, VCI236DS, VCI248DS
CIRCUIT BREAKER
120V AC, 60 Hz
15 Amp
178
Page 50
CUSTOM INSERTS
PLANNING INFORMATION
VENTILATION — CUSTOM INSERTS
INSTALLATION CONSIDERATIONS
The information in this design guide provides key features, product dimensions and installation speci cations. Before installing a Thermador Custom Hood Insert, be sure to verify the dimensions and electrical connections. Also, always consult with the installation manual packed with the product for complete details before installing.
Professional Custom Series Hood Inserts are designed for installation with all professional-style cooktops and ranges. Masterpiece Custom Series Hood Inserts are designed for installation with non-professional gas, electric or induction cooktops. Refer to the appropriate section for additional speci cations.
HOOD WIDTH
The hood width should be no less than the width of the cooking surface. Where space is not restricted, a wider hood can be used to increase your capture area.
DISTANCE FROM COOKING SURFACE
Proper mounting height is very important. If a hood is mounted too low, it may be dif cult to cook and be unsafe. If a hood is mounted too high, performance may be compromised. For optimal performance, the distance from the cooking surface to the bottom of the hood should be a minimum of 30", unless otherwise noted. Please refer to the installation manual for each hood and cooktop/range model for proper hood mounting heights.
CHOOSING THE RIGHT CFM
The power of the cooktop or range, measured in BTU, is perhaps the most important factor in determining CFM needs for a hood. Professional Gas Cooktops generally should have 1 CFM for every 100 BTU. For Masterpiece Electric and Induction Cooktops, and Gas Cooktops under 60,000 BTU, choose a blower with a minimum of 100 CFM per 12" of cooktop width.
You should also consider the cooking space and cooking style of your client.
• More demanding cooks usually require more exhaust capacity to handle moisture generated by boiling large pots of water or the grease and smoke resulting from grilling or frying. This cooking style could require a hood or downdraft system with air ow of 600 to 1,300 CFM.
• For those who are used to preparing quick meals in a relatively small kitchen, a hood with 400 to 600 CFM may be adequate ventilation for the cooking space.
• If the cooking surface is in a peninsula or island, a larger capacity hood can provide better capture when there are cross currents and when the hood needs to be mounted higher. Downdraft ventilation systems are also a good alternative.
• High heat cooking or aromatic foods may require additional CFM. Increasing capture area by 3" on each side is also a recommended way to address this issue.
LENGTH AND SIZE OF DUCTWORK
Do not use  exible duct; it creates back pressure/air turbulence and reduces performance.
Straight runs and gradual turns are best. Use the shortest route with the fewest turns possible.
CHOOSING THE CORRECT BLOWER
A variety of interior and exterior blower options Remote, Inline or Integrated) are available for Thermador’s Professional and Masterpiece Series Hoods. If the unit you have selected does not have a blower included, one can be purchased separately. Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most ef cient air  ow exhaust, use a straight run or as few elbows as possible.
Remote Blowers (VTR Series) Depending on your preference and ducting situation, these blowers can be mounted on the roof or exterior wall of your home. An exterior installation may be more appealing to reduce noise in the kitchen.
Inline Blowers (VTI series) To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If you have easy access to your duct line (in an attic, for example), this may be an appealing option.
Integrated Blowers (VTI series) These blowers are purchased separately and integrated into the hood or onto the downdraft unit at the time of installation. This option allows you to select your ideal hood with the exact power you require.
Proper performance is dependent upon proper ducting. Use a quali ed and trained installer. Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than speci ed CFM of air movement. The speci ed CFM varies from locale to locale. Consult your HVAC professional for speci c requirements in your area.
If using a 10" duct, Thermador recommends not exceeding 150 feet of duct. Transitions, elbows and wall or roof caps are all factors that will add more static pressure, therefore increasing your equivalent duct run.
INSTALLATION NOTE: Professional Rangetops and Ranges require that minimum distances be maintained from the cooking surface to combustible materials (i.e. a wood covering around the insert). These minimum distances range from 30" to 36" and can vary from product to product and by manufacturer. Refer to the installation manual of the rangetop or range prior to the design and installation of the custom hood insert.
WARRANTY
Limited warranty parts and labor (2 year).
See page 302 for additional warranty details.
1.800.735.4328 | THERMADOR.COM
179
Page 51
VENTILATION
CUSTOM INSERT (36"/48"/54")
VCIN36JP / VCIN48JP / VCIN54JP
PROFESSIONAL
VCIN36JP – 36-Inch
VCIN48JP – 48-Inch
VCIN54JP – 54-Inch
Custom hood insert for use within wall or island custom hood applications
SPECIFICATIONS
Available Hood Widths 36" / 48" / 54"
Blower Sold Separately
Duct Size at Discharge 10" Round
Ducting Direction Vertical
Dishwasher-safe Filters Stainless Steel Baf es
Halogen Lighting 12 V, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60Hz
See Blower Options Table
36"– 2 Bulbs 48" / 54"– 4 Bulbs
VCIN36JP / VCIN48JP / VCIN54JP
PERFORMANCE
- Suitable for wall or island applications
- Three fan speeds
- Auto function senses heat from the cooking surface and adjusts fan speeds
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe stainless steel baf e  lters
- Filter systems are highly ef cient at capturing grease
- Deep capture area allows for ef cient capture of smoke and steam
- Powerfully Quiet
- 10" duct outlet
DESIGN
- Stainless steel button controls
- Halogen lighting spotlights your best recipes
- Remote control accessory
®
ventilation systems
ROOF JACK, WALL CAP & TRANSITION
Roof Jack – RJ310 8-Inch Wall Cap–WC8 Wall Cap – WC310 10-Inch Wall Cap–WC10 Transition
ACCESSORIES
Custom Hood Liners
LINER236 For 36" Insert VCIN36JP LINER248 For 48" Insert VCIN48JP LINER254 For 54" Insert VCIN54JP
32
7
/16
44
” (1129mm)
7
1
/2
1
(38mm)
23
5
/16
” (592mm)
50
/16
” (1281mm)
- Stainless steel custom hood liners to protect the exterior base of custom insert
7
/16
” (824mm)
” (995mm)
3
/16
39
” (1300mm)
/16
3
” (1453mm)
51
/16
3
57
5
/8
20
(524mm)
Cabinet Trim
11
/16
” (17mm)
Remote Control Panel
VCI2REMKS
- Stainless steel  nish
- Cable-connected to blower and hood controls
- Cable length 30 ft.
5
1
/16
7
/16
8
332
Stainless Steel Backsplash
PA36JBS 36" wide PA48JBS 48" wide
5
3
/16
84
1
13
/16
180
Page 52
VENTILATION
CUSTOM INSERT (36"/48"/54")
VCIN36JP / VCIN48JP / VCIN54JP
VENTILATION — CUSTOM INSERTS
INSTALLATION OPTIONS
Thermador Custom Hood Inserts within custom hood applications create a seamless design with wall or island applications.
Thermador Professional Series Custom Hood Inserts may be installed above a Thermador Professional Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. Professional Rangetops and Ranges require that minimum distances be maintained from the cooking surface to combustible materials (i.e. a wood covering around the insert). These minimum distances range from 30" to 36" and can vary from product to product and by manufacturer. Refer to the installation manual of the rangetop or range prior to the design and installation of the custom hood insert.
These hoods are designed to be used for vertical discharge. A blower must be purchased separately.
BLOWER OPTIONS (for VCIN__JP)
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
INLINE
VTI610D – 600 CFM
VTI1010D – 1000 CFM
INTEGRATED
VTN630C – 600 CFM
VTN1030C– 1000 CFM
See page 177 for further details.
HOOD DIMENSIONS
(See installation manual for complete planning instructions)
13
/16
12
(325mm)
5
/8
20 (524mm)
16
5
/8
” (422mm)
3
/4
21 (553mm)
32
44
50
CUTOUT DIMENSIONS WHEN USING A LINER
3
/4
39
” (1010mm)
3
/4
” (1315mm)
51
3
/4
”” (1467mm)
57
5
/8
” (16mm)
7
/8
” (606mm)
23
15
/16
32
” (836mm)
15
/16
” (1141mm)
44
15
/16
” (1294mm)
CUTOUT DIMENSIONS
50
WHEN NOT USING A LINER
1
21
/4
” (540mm)
3
/8
3
8
/
3
/8
” (822mm)
” (1127mm)
” (1280mm)
Cabinet Trim
11
/16
5
4 (110mm)
” (17mm)
/16
5
/8
” (16mm)
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
1.800.735.4328 | THERMADOR.COM
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
INTEGRATED (Mounted on hood)
VTN630C – 600 CFM
VTN1030C – 1000 CFM
181
Page 53
VENTILATION
CUSTOM INSERT WITH BLOWER (36"/48"/54")
VCIB36JP / VCIB48JP / VCIB54JP
VCIB36JP / VCIB48JP / VCIB54JP
PERFORMANCE
- Suitable for wall or island applications
- Three fan speeds
- Auto function senses heat from the cooking surface and adjusts fan speeds
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
PROFESSIONAL
VCIB36JP – 36-Inch
VCIB48JP – 48-Inch
VCIB54JP – 54-Inch
Custom hood insert for use within wall or island custom hood applications
SPECIFICATIONS
Available Hood Widths 36" / 48" / 54"
Blower Integrated 1000 CFM
Duct Size at Discharge 10" Round
Ducting Direction Vertical
Dishwasher-safe Filters Stainless Steel Baf es
Halogen Lighting 12 V, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60Hz
Blower Included
36"– 2 Bulbs 48" / 54"– 4 Bulbs
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe stainless steel baf e  lters
- Filter systems are highly ef cient at capturing grease
- Deep capture area allows for ef cient capture of smoke and steam
- Powerfully Quiet
- 10" duct outlet
DESIGN
- A unique all in one box solution that includes the hood, a 1,000 CFM blower, liner, baf e  lters, lights, transition and a back-draft damper
- Stainless steel button controls
- Halogen lighting spotlights your best recipes
- Remote control accessory
®
ventilation systems
ROOF JACK, WALL CAP & TRANSITION
Roof Jack – RJ310 8-Inch Wall Cap–WC8 Wall Cap – WC310 10-Inch Wall Cap–WC10 Transition
ACCESSORIES
Remote Control Panel
VCI2REMKS
- Stainless steel  nish
- Cable-connected to blower and hood controls
- Cable length 30 ft.
5
3
/16
Stainless Steel Backsplash
PA36JBS 36" wide PA48JBS 48" wide
84
1
13
5
1
/16
7
/16
8
/16
332
182
Page 54
VENTILATION
CUSTOM INSERT WITH BLOWER (36"/48"/54")
VCIB36JP / VCIB48JP / VCIB54JP
VENTILATION — CUSTOM INSERTS
INSTALLATION OPTIONS
Thermador Custom Hood Inserts within custom hood applications create a seamless design with wall or island applications.
Thermador Professional Series Custom Hood Inserts may be installed above a Thermador Professional Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. Professional Rangetops and Ranges require that minimum distances be maintained from the cooking surface to combustible materials (i.e. a wood covering around the insert). These minimum distances range from 30" to 36" and can vary from product to product and by manufacturer. Refer to the installation manual of the rangetop or range prior to the design and installation of the custom hood insert.
These hoods are designed to be used for vertical discharge.
BLOWER PRESSURE CURVES
VCIB__JP
HOOD DIMENSIONS
(See installation manual for complete planning instructions)
11
13
1
/16
12
/8
5
23 (592mm)
” (283mm)
16
5
/8
” (422mm)
20
5
/8
” (524mm)
/16
50
1
/2
1
(38mm)
23
5
/16
1
/2
1 (38mm)
” (592mm)
(325mm)
3
/4
21 (553mm)
44
7
/16
” (1281mm)
32
7
/16
” (1129mm)
7
/16
” (824mm)
39
51
57
39
” (995mm)
3
/16
” (1300mm)
3
/16
” (1453mm)
3
/16
” (995mm)
3
/16
/16
3
51
57
1
/2
4 (114mm)
Cabinet Trim
” (17mm)
11
/16
” (1300mm)
” (1453mm)
/16
3
3
” (995mm)
/16
39
3
” (1300mm)
6
1
/
51
3
” (1453mm)
/16
57
5
/8
20
(524mm)
Cabinet Trim
11
/16
” (17mm)
NOTE: All measurements are made with 3 ft. straight duct, 90° bend and 1 ft. straight duct at exhaust. These are NOT free blowing measurements.
CUTOUT DIMENSIONS WHEN USING A LINER
3
/4
39
” (1010mm)
3
/4
” (1315mm)
51
3
/4
”” (1467mm)
57
5
/8
” (16mm)
7
/8
23
” (606mm)
CUTOUT DIMENSIONS WHEN NOT USING A LINER
15
/16
32
” (836mm)
15
/16
” (1141mm)
44
15
/16
” (1294mm)
50
5
/8
” (16mm)
1
/4
” (540mm)
21
1.800.735.4328 | THERMADOR.COM
183
Page 55
VENTILATION
CUSTOM INSERT (30"/36"/48")
VCI230DS / VCI236DS / VCI248DS
MASTERPIECE
VCI230DS – 30-Inch
VCI236DS – 36-Inch
VCI248DS – 48-Inch
Custom hood insert for use within wall or island custom hood applications
VCI230DS / VCI236DS / VCI248DS
PERFORMANCE
- Suitable for wall or island applications
- Three fan speeds
- Built-in ‘Clean Filter‘ reminder light illuminates after 40 hours of operation
- Delayed shut-off tackles lingering odors for up to 10 minutes
- Dishwasher-safe aluminum mesh  lters
- Filter systems are highly ef cient at capturing grease
- Deep capture area allows for ef cient capture of smoke and steam
- Powerfully Quiet
- 10" Round duct size
- Vertical ducting direction
- Blowers sold separately
- Choose from Inline, Remote or Integrated Blowers
- Accessories include: Liner, Remote Control and Stainless Steel Baf e Filters
DESIGN
- Stainless steel button controls
- Halogen lighting spotlights your best recipes
®
ventilation systems
SPECIFICATIONS
Available Hood Widths 30" / 36" / 48"
Blower Sold Separately —
Duct Size at Discharge 10" Round
Ducting Direction Vertical
Dishwasher-safe Filters Mesh (Baf e  lters sold
Halogen Lighting 120 Volt, 20 Watt Max., G-4 Base, Included
Electrical 120V AC, 60Hz
See Blower Options Table
as an accessory)
30" / 36" – 2 Bulbs 48"– 4 Bulbs
ACCESSORIES
Custom Hood Liners
LINER30 for 30" Insert LINER36 for 36" Insert LINER48 for 48" Insert
- Stainless steel custom hood liners to protect the exterior base of custom insert
- Custom hood liner completes custom insert installation
ROOF JACK & WALL CAP (For Integral and Inline blowers)
Roofjack – RJ310 8-Inch Wall Cap – WC8
Wall Cap–WC310 10-Inch Wall Cap–WC10
Remote Control Panel
VCI2REMFS
- Stainless steel  nish
- Cable-connected to blower and hood controls
- Cable length 30 ft.
Baf e Filters
BAFFLT30 30" wide BAFFLT36 36" wide BAFFLT48 48" wide
- Stainless steel  nish
- Unique low pro le design maximizes grease capture
- Dishwasher-safe for easy cleanup
184
Page 56
VENTILATION
CUSTOM INSERT (30"/36"/48")
VCI230DS / VCI236DS / VCI248DS
VENTILATION — CUSTOM INSERTS
VENTILATION — CUSTOM INSERTS
INSTALLATION OPTIONS
Thermador Custom Hood Inserts within custom hood applications create a seamless design with wall or island applications.
Thermador Professional Series Custom Hood Inserts may be installed above a Thermador Professional Cooktop or Range to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
Hood installation height above a cooktop can vary. Professional Rangetops and Ranges require that minimum distances be maintained from the cooking surface to combustible materials (i.e. a wood covering around the insert). These minimum distances range from 30" to 36" and can vary from product to product and by manufacturer. Refer to the installation manual of the rangetop or range prior to the design and installation of the custom hood insert.
These hoods are designed to be used for vertical discharge. A blower must be purchased separately.
BLOWER OPTIONS
REMOTE
VTR630D – 600 CFM Use RFPLT600 in
roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in
roof-mount applications
VTR1330E – 1300 CFM Use RFPLT1000 in
roof-mount applications
INLINE
VTI610D – 600 CFM
VTI1010D* – 1000 CFM
INTEGRATED
VTI610D – 600 CFM Inline blower can be used
VTI1010D* – 1000 CFM Inline blower can be used
See pages 134-135 for further details. * Please visit thermador.com for tips & hints on installation of VTI1010D as
an integrated solution
for an integrated solution
for an integrated solution
HOOD DIMENSIONS
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM VTR1330E – 1300 CFM
INLINE (Mounted between kitchen and external wall) & INTEGRATED (Mounted on hood)
VTI610D – 600 CFM VTI1010D – 1000 CFM
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
1.800.735.4328 | THERMADOR.COM
* Please refer to thermador.com for tips and hints on installation of VTI1010D as an integrated solution
RFPLT1000 For use with Remote Blowers VTR1030D and VTR1330E
185
Page 57
MODELS SHOWN: UCVM36FS 36-INCH DOWNDRAFT WITH CIT365KM INDUCTION COOKTOP186
Page 58
VENTILATION
DOWNDRAFT
If you prefer a concealed look, choose a Thermador Downdraft Ventilation Unit, which offers space ef ciency when a hood is not preferred. The full-face  lter combines a  lter with a splatter shield in one easy-to-remove, dishwasher-safe element. Thermador invented the  rst retractable downdraft, and was also the  rst to introduce a recirculation option for downdrafts—making ventilation possible in any kitchen.
VENTILATION — DOWNDRAFT
1.800.735.4328 | THERMADOR.COM
187
Page 59
DOWNDRAFT
FEATURES & BENEFITS
FULL 13-INCH RISE
With an over 13-inch intake, the UCVM rises well above even the tallest pans. This protects against splatters when cooking and provides better performance in capturing steam and smoke — even from the front burners.
DOWNDRAFT RECIRCULATION OPTION
Downdraft recirculation is now available for island or wall applications. Combine the performance of the UCVM Downdraft with the odor- and grease-capturing  lters in the Recirculation Module for the perfect ventilation combination for anywhere in your kitchen.
FULL-FACE FILTERS
Full-face  lters combine a  lter with a splatter shield in one easy­to-remove, dishwasher-safe element. These  lters maximize grease capture without affecting air ow.
PLANNING INFORMATION
MODEL OPTIONS
Thermador Downdraft Hoods are available in 30 and 36-inch widths to  t your kitchen plans and are meticulously crafted for both function and design. Be sure to reference the correct model information in this design guide.
ELECTRICAL SPECIFICATIONS
Be sure your Thermador Downdraft Hood is properly installed and grounded by a quali ed technician. Installation, electrical connections and grounding must comply with all applicable local codes.
REQUIRED CIRCUIT
MODEL
UCVM30FS, UCVM36FS 15 Amp
BREAKER
120V AC, 60 Hz
INSTALLATION CONSIDERATIONS
The information in this design guide provides key features, product dimensions, cutouts and installation speci cations. Before installing a Thermador Downdraft Hood, be sure to verify the cutout dimensions and electrical connections. Also, always consult with the installation manual packed with the product for complete details before installing.
Thermador Downdraft Hoods may be installed in a wall or island behind a Thermador non-professional gas, electric or induction cooktop to create a convenient cooking center. Refer to the appropriate section for additional speci cations.
HOOD WIDTH
Downdraft ventilation units should be the same width as the cooking surfaces they are ventilating.
CHOOSING THE CORRECT BLOWER
A variety of interior and exterior blower options (Remote, Inline or Integrated) are available for Thermador’s Downdraft Hoods. If the unit you have selected does not have a blower, one can be purchased separately. Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most ef cient air  ow exhaust, use a straight run or as few elbows as possible.
188
Remote Blowers (VTR Series) Depending on your preference and ducting situation, these blowers can be mounted on the roof or exterior wall of your home. An exterior installation may be more appealing to reduce noise in the kitchen.
Inline Blowers (VTI series) To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If you have easy access to your duct line (in an attic, for example), this may be an appealing option.
Integrated Blowers (VTN series) These blowers are purchased separately and integrated into the hood or onto the downdraft unit at the time of installation. This option allows you to select your ideal hood with the exact power you require.
Page 60
DOWNDRAFT
FEATURES & BENEFITS
VENTILATION — DOWNDRAFT
CHOOSING THE RIGHT CFM
The power of the cooktop, measured in BTU, is perhaps the most important factor in determining CFM needs for a hood. Professional Gas Rangetops generally should have 1 CFM for every 100 BTU.
You should also consider the cooking space and cooking style of your client.
• More demanding cooks usually require more exhaust capacity to handle moisture generated by boiling large pots of water or the grease and smoke resulting from grilling or frying. This cooking style could require a hood or downdraft system with air ow of 600 to 1,300 CFM.
• For those who are used to preparing quick meals in a relatively small kitchen, a hood with 600 CFM may be adequate ventilation for the cooking space.
• If the cooking surface is in a peninsula or island, a larger capacity hood can provide better capture when there are cross currents and when the hood needs to be mounted higher. Downdraft ventilation systems are also a good alternative.
• High heat cooking or aromatic foods may require additional CFM. Increasing capture area by 3" on each side is also a recommended way to address this issue.
LENGTH AND SIZE OF DUCTWORK
Do not use  exible duct; it creates back pressure/air turbulence and reduces performance.
Straight runs and gradual turns are best. Use the shortest route with the fewest turns possible.
Proper performance is dependent upon proper ducting. Use a quali ed and trained installer. Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than speci ed CFM of air movement. The speci ed CFM varies from locale to locale. Consult your HVAC professional for speci c requirements in your area.
BLOWER OPTIONS
REMOTE Requires CV2T6 or CV2T10 Transition
VTR630D – 600 CFM Use RFPLT600 in roof-mount applications
VTR1030D – 1000 CFM Use RFPLT1000 in roof-mount applications
INLINE Requires CV2T6 or CV2T10 Transition
VTI610D – 600 CFM
VTI1010D – 1000 CFM
INTEGRATED
VTN600CV2C – 600 CFM
REMOTE (Mounted to roof or external wall)
VTR630D – 600 CFM VTR1030D–1000 CFM
INLINE (Mounted between kitchen and external wall)
VTI610D – 600 CFM VTI1010D – 1000 CFM
If using a 10" duct, Thermador recommends not exceeding 150 feet of duct. Transitions, elbows and wall or roof caps are all factors that will add more static pressure, therefore increasing your equivalent duct run.
WARRANTY
Limited warranty parts and labor (2 year)
See page 302 for additional warranty details.
REMOTE BLOWER ACCESSORIES
RFPLT600 For use with Remote Blower VTR630D
1.800.735.4328 | THERMADOR.COM
INTEGRATED (Mounted on hood)
VTN600CV2C – 600 CFM
RFPLT1000 For use with Remote Blower VTR1030D
189
Page 61
VENTILATION
DOWNDRAFT (30"/36")
UCVM30FS / UCVM36FS
MASTERPIECE
UCVM30FS – 30-Inch
UCVM36FS – 36-Inch
UCVM30FS / UCVM36FS
PERFORMANCE
- Suitable for wall or island applications
- Downdraft rises over 13" to capture steam from the tallest pots
- Downdraft recirculation possible with module RECIRC36DF
- Three fan speeds
- Dishwasher-safe full-face  lters also act as a splatter shield
- Filter systems are highly ef cient at capturing grease
- Powerfully Quiet
- Blowers sold separately
- Choose from Inline, Remote or Integrated Blowers
DESIGN
- Brushed stainless steel  nish
- Easy-to-operate control buttons
®
ventilation systems
SPECIFICATIONS
Available Hood Widths 30" / 36"
Blower Sold Separately —
See Blower Options Table
Duct Size at Discharge 6" Round
Ducting Direction Down, Left or Right
Dishwasher-safe Filters Full-Face Mesh Electrical 120V AC, 60Hz
ACCESSORIES
Recirculation Kit
RECIRC36DF
- Comes complete with 2 charcoal  lters, 2 venting grids, and ducting to transition to integrated blower (blower sold separately)
- For toekick heights of 4" or taller
- Wall or island applications
- Easily mounts to integrated blower (VTN600CV2C) under cooktop
- Toekick/socket can be vented in any direction
- Mounts to base of cabinet; recesses into toekick
- To be used only with Thermador Downdraft and Integrated Blower
- Replacement  lters are ordered as a service item
- Filters should be replaced twice a year
TRANSITIONS
Transition piece required for installation of inline and remote blowers — downdraft applications only
CV2T6
Transition piece required for installation of 600 CFM Inline and Remote Blowers with 6" duct connections — downdraft applications only
CV2T10
Improves overall performance when installing with Thermador’s 1,000 CFM Inline or Remote Blowers with 10" duct connections — downdraft applications only
6 3/4"
15 1/8"
7
14
Replacement Charcoal Filters
Sold separately as service item #291108 (For use with recirculation module)
14 3/8"
14 3/8"
/
"
1616
Ø 10"
11"
Ø 6"
190
Page 62
VENTILATION
DOWNDRAFT (30"/36")
UCVM30FS / UCVM36FS
VENTILATION — DOWNDRAFT
VENTILATION — DOWNDRAFT
INSTALLATION OPTIONS
The Thermador Downdraft Hood System is available in 30-inch or 36-inch widths. It is intended for installation with Thermador non-professional gas, electric or induction cooktops only.
A Recirculation Kit (RECIRC36DF) can be purchased separately and used in conjunction with the Integral Blower if ducting to the outside is not a viable option. Refer to the appropriate section for additional speci cations.
These hoods are designed to be used for side or downward discharge.
36 7/8"
(936 mm)
30 7/8"
(784 mm)
CUTOUT DIMENSIONS (TOP VIEW)
36 7/8"
7
30
/8"
36 7/8"
7
30
/8"
1.800.735.4328 | THERMADOR.COM
36 7/8"
30
7
/8"
191
Loading...