Thermador PA48JLBG, PA48JHSSG Installation
Backguard & Toe Kick
Installation Instructions
Before you begin read these instructions carefully. Observe all local codes and ordinances.
INSTALLER: Please leave these Installation Instructions with the owner.
OWNER: Please retain these instructions for future reference.
AVAILABLE FOR THESE MODELS:
PRD364JDGU
PRD364JDGC
PRD366JGU
PRD366JGC
PRD486JDGU
PRD486JDGC
PRD48JDSGU
PRD48JDSGC
PRG366JG
PRL366JG
PRG364JDG
PRL364JDG
PRG486JDG
PRL486JDG
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
Pro Grand
®
36" Dual Fuel Range 4 Burner Griddle
®
36" Dual Fuel Range 4 Burner Griddle - Canadian
®
36" Dual Fuel Range 6 Burner
®
36" Dual Fuel Range 6 Burner - Canadian
®
48" Dual Fuel Range 6 Burner Griddle
®
48" Dual Fuel Range 6 Burner Griddle - Canadian
®
48" Dual Fuel Range w/ Steam Oven
®
48" Dual Fuel Range w/ Steam Oven - Canadian
®
36" Gas Range 6 Burner
®
36" Gas Range 6 Burner - LP
®
36" Gas Range 4 Burner Griddle
®
36" Gas Range 4 Burner Griddle - LP
®
48" Gas Range 6 Burner Griddle
®
48" Gas Range 6 Burner Griddle - LP
Backguard Installation
WARNING:
To reduce the risk of fire or injury to
persons, check to make sure all
packaging has been removed from
accessory devices before use.
WARNING:
Fingers or hands could get pinched
when installing the backguard. Severe
injury could result. Use extreme caution
and wear thick protective gloves to avoid
potential laceration to finger or hand
while sliding the backguard down onto
the range.
CAUTION:
The High Shelf can get very hot! DO
NOT place the following items on top of
the High Shelf:
• plastics or containers that can melt
• flammable items
• a total load over 30 pounds (13.6kg)
Note: If a backsplash is to be used in addition to a
backguard, install the backsplash first and the
backguard second, before sliding range into place.
High Shelf
Low Back
Figure 1: High Shelf & Low Back Front View
English 1
High Shelf Parts Included
(1) High Shelf top panel
(1) High Shelf front panel
(13) T-20 Torx Stainless screws
(16 or 14) T-20 Torx drill point
screws
(1) Installation Guide
The backguard must be attached before sliding the
range into the final installed position. When there is
less than a 12" (305mm) horizontal clearance
between combustible surfaces ∆ and the back
edge of the range above the cooking surface, a
THERMADOR® Low Back or High Shelf must be
purchased separately and installed. When clearance to combustible surfaces ∆ is over 12"
(305mm) or for island installations, the supplied
THERMADOR® Flush Island Trim may be used.
High Shelf Assembly
Low Back Parts Included
(1) Low Back panel
(9 or 8) T-20 Torx stainless screws
(8 or 6) T-20 Torx drill point screws
(1) Installation Guide
Tools Needed
T-20 Torx head screwdriver or drill
Protective Work Gloves
Backguard Kit Model Numbers
Model 36” 48” 48” Steam
Low Back PA36JLBG PA48JLBG PA48JLBSG
High Shelf PA36JHSG PA48JHSG PA48JHSSG
(5x) screws along the top
(12x) screws along the back
Figure 2: Backguard Rear View
1. Remove protective plastic.
2. Slide the shelf onto the backguard channel.
3. Install the included (5) stainless screws along the topside of shelf and (8) stainless screws into the back of the shelf.
4. Begin with Backguard Installation.
Flush
Island
Trim
Included on
Range
Included on
Range
Included on
Range
English 2
Backguard Installation
High Shelf
Low Back
Mounts inside side panel flange
Flush Island Trim
(Included with range)
Mounts inside back panel flange
1. Remove protective plastic.
2. Depending on model, remove the (3) or (4) T20 Torx stainless screws in the front face of the
Mounts inside side panel flange
included Flush Island Trim, the (4) drill point
screws securing the trim to the side panels,
and the (2) or (4) drill point screws securing the
piece to the back panel. Lift up to fully remove.
3. Align the back panel of the new accessory with the flanges on the range side panels right and left rear corners. The backguard is inserted inside the guide channels on the back of the range.
4. Make sure the backguard’s front face is outside the flange on the front side of the range.
5. Re-install screws in the new backguard’s front and back panels.
6. Re-install (4) drill point screws to secure the
backguard’s back panel to the side panels on
the back of the range.
Figure 3: Backguard Installation
English 3
Toe Kick Panel
(PA [36,48] JTKG)
Toe Kick Parts Included
(1) Toe Kick panel
(4) T-20 Torx drill point screws
(1) Installation Guide
Tools Needed
T-20 Torx head screwdriver or drill
Protective Work Gloves
1. Remove the leg covers by sliding the top, outer
sleeve of the leg covers off the extruded dimples of the cast aluminum base.
2. Remove protective plastic covering from the Toe Kick Panel.
3. Beneath the range, with the holes and flange facing up, wrap the Toe Kick Panel around the cast aluminum base.
4. The mating part has extruded dimples on both sides for which the holes of the Toe Kick Panel should seize. You should feel a definitive snap, letting you know that the part has been installed.
5. Mount the Toe Kick Panel on both sides of the
unit into the extruded dimples using the (4) T20 Torx drill point screws provided.
Remove
Leg Covers
Mounting hole locations (x2)
Figure 5: Toe Kick Panel Installation
Figure 4: Leg Covers
English 4
Loading...