Thermador 9000039271 User Manual
DISHWASHER INSTALLATION INSTRUCTIONS
Table of Contents
IMPORTANT INSTRUCTIONS ....................... 1
Tools Needed ..................................................... 2
Materials Needed ............................................... 2
Materials Supplied .............................................. 3
Enclosure Preparation ....................................... 4
Electrical Preparation ........................................ 5
Plumbing Preparation ..................................... 6-7
Dishwasher Preparation ................................. 7-8
Door Panel Installation ....................................... 9
IMPORTANT INSTRUCTIONS
WARNING - OBSERVE ALL WARNINGS AND CAUTIONS
These instructions are intended for use by qualified installers only.
In addition to these instructions, the dishwasher
shall be installed:
• In accordance with all local codes or, in the
absence of a local code,
• In the United States, with the National Electric
Code.
• In Canada, with the Canadian Electric Code
C22.1 -latest edition/Provincial and Municipal
codes and/or local codes.
Read these installation instructions completely
and follow them carefully. They will save you
time and effort and help to ensure safety and
optimum dishwasher performance.
CAUTION: If the dishwasher is installed in a
location that experiences freezing temperatures
(e.g., in a holiday home), you must drain all the
water from the dishwasher’s interior. Water system
ruptures that occur as a result of freezing are not
covered by warranty.
Placing the Dishwasher ................................... 10
Securing the Dishwasher ................................ 10
Drain Hose Connection .................................... 11
Hot Water Connection ..................................... 12
Electrical Connection .................................. 13-14
Door Tension Adjustment ................................. 14
Base and Toe Panel.................................... 14-15
Final Instructions .............................................. 15
Customer Service ............................................ 16
IMPORTANT
• The dishwasher drain hose must be installed
with a portion of it at least 20” (508mm) off the
cabinet floor; otherwise the dishwasher may not
drain properly.
• This dishwasher is intended for residential use
only, and should not be used in commercial food
service establishments.
• NEW INSTALLATION - If the dishwasher is a
new installation, most of the work must be done
before the dishwasher is moved into place.
• REPLACEMENT - If the dishwasher is replacing
another dishwasher, check the existing
dishwasher connections for compatibility with
the new dishwasher, and replace parts as necessary.
Inspect the Dishwasher
After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for
possible freight or cosmetic damage. Report any
damage immediately. Cosmetic defects must be
reported within 5 days of installation.
NOTE: Do not discard any bags or items that
come with the original package until after the entire
installation has been completed.
P/N 9000039271 (8408)
1
TOOLS NEEDED
Hammer Hole
Saw
Tape
Measure
Wire
Cutter
Slot
Screwdriver
Wire
Stripper
Pipe
Wrench
Phillips
Screwdriver
Drill
MATERIALS NEEDED
(Additional materials may be required to comply with local codes.)
Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1 ground, insulated copper conductors.
Adjustable
Wrench
Torx
Screwdriver
Level
Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
Shut-off valve and fittings appropriate for hot water supply line (copper
tubing/compression fitting, or braided hose).
90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your
water supply line (copper tubing/compression fitting, or braided hose) on the
other leg.
Teflon tape or other pipe thread compound to seal plumbing connections.
UL listed conduit connector or strain relief.
2
MATERIALS SUPPLIED
A
B
Accessory Parts Supplied
Accessory Parts for your dishwasher will come in
one or more plastic bags. Check to make sure that
the parts shown in Figure 1 are included with your
model. If any parts are missing, contact your dealer
immediately.
NOTE: Illustrations are not to scale.
C
Manual Set Bag
This dishwasher comes with a Manual Set Bag
containing:
D
• Use & Care Instructions and Installation Instructions
• Quick Reference Guide
• Extra Tall Item Sprinkler (Fig. 1, letter A)
E
DWHD94BF also has SHI/SHV a Panel Installation
Template Sheet (Figure 1, letter B).
F
DWHD94BP and DWHD94BS also have a Cotton
Insulation Strip (Figure 1, letter C).
G
Dishwasher Installation Kit
This dishwasher comes with a Dishwasher Installa-
H
tion Kit containing:
D. Toe Panel Screws (2)
I
J
E. Mounting Brackets (2)
F. Mounting Bracket Screws (2)
G. Rubber Connection Hose (1)
and Drain Hose Clamps (2)
H. Wire Nuts (3)
K
I. Junction Box Screws (2)
DWHD94BF
In addition to a Manual Set Bag and an Installation Kit
L
Bag, DWHD94BF models also come with a Door
Panel Installation Kit containing:
J. Caps (2)
K. Spring Tension Screw (2)
M
L. Door Mounting Brackets (2 plastic)
w/Screws (4);
N
Mounting Door Brackets (2 metal)
w/Screws (4)
M. Wood Screws (2)
O
DWHD94BP and DWHD94BS
In addition to a Manual Set Bag and an Installation Kit
Figure 1
Bag, these models also come with a Toe Panel
Installation Kit containing:
N. Toe Panel Screws (2)
O. Base Part Screws (2)
3
ENCLOSURE PREPARATION
23-9/16"
(598mm)
NOTE: This dishwasher is designed to be enclosed
on the top and both sides by standard residential
kitchen cabinetry.
Select a location as close to the sink as possible for
90°90°
easy access to water supply and drain lines.
For proper dishwasher operation and appearance,
ensure that the enclosure is square and has the
34"
(864mm)
minimum
dimensions shown in Figure 2.
If the dishwasher is to be installed in a corner, make
sure that there is adequate clearance to open the
door, as shown in Figure 3, letter A.
WARNING: ELECTRICAL SHOCK/FIRE
23-5/8" – 24-1/4" (600–616 mm)
Figure 2
HAZARD - Do not allow the electrical and
water supply lines to touch. Separate
channels are provided under the
dishwasher (see page 10).
If the enclosure requires openings for the electrical
supply cable, hot water supply line, and dishwasher
drain hose, place them within the dimensions
A
Countertop
Figure 3
shown by the shaded area of Figure 4 to avoid
interference with the dishwasher frame or other
components. Make the openings for the electrical
supply cable and hot water supply line 1” (25.4mm)
diameter. Make the opening for the dishwasher drain
hose 1-1/4” (32mm) diameter. If the openings are
made through wood, sand them smooth. If the
openings are made through metal, make them large
enough to accommodate grommets or other
protective sheaths with inside diameters of 1”
(25.4mm) for the electrical supply cable and the hot
water supply line, and 1-1/4” (32mm) for the dishwasher drain hose.
23-5/8" – 24-1/8"
(600mm – 613mm)
3-1/2"
(89mm)
1-5/16"
(33mm)
Figure 4
4
3/8" - 1/2"
( 8mm - 13mm)
3" - 4"
( 75mm - 100mm)
ELECTRICAL PREPARATION
HAZARD - Working on an energized circuit
could result in serious injury or death. Only
qualified electricians should perform electrical work. Do not attempt any work on the
dishwasher electric supply circuit until you
A
B
(762mm)
21"
(533mm)
Figure 5
30"
are certain the circuit is de-energized.
electrical work can cause fire. Only qualified
electricians should perform electrical work.
Electrical Supply
The customer has the responsibility of ensuring that
the dishwasher electrical installation is in compliance with all national and local electrical codes and
ordinances. The dishwasher is designed for an
electrical supply of 120V, 60 Hz, AC, connected to a
dishwasher-dedicated, properly grounded electrical
circuit with a fuse or breaker rated for 15 amps. If
the dishwasher is connected with a food disposer, a
20 amp (and no higher) fuse or circuit breaker may
be used. Electrical supply conductors shall be a
minimum #14 AWG copper wire.
Regardless of where the electrical supply cable
enters the enclosure (following the guidelines on
page 8), position the cable 21” (533mm) from the
enclosure’s left side, as shown in Figure 5, letter A.
Extend the cable 30” (762mm) from the enclosure’s
back, as shown in Figure 5, letter B.
WARNING: ELECTRICAL SHOCK
WARNING: FIRE HAZARD - Improper
Figure 6
Remove 3” - 4” (75mm - 100mm) of the cable’s
outer casing, as shown in Figure 6, letter C, then
remove 3/8” - 1/2” (9 - 13mm) of insulation from
each conductor, as shown in Figure 6, letter D.
Dishwasher Electrical Rating
stloVztreHserepmAsttaW
0210651
054,1
)xam(
5
Loading...