TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Fast Transient Response Using Small
Output Capacitor (10 µF)
D
200-mA Low-Dropout Voltage Regulator
D
Available in 1.5-V, 1.8-V, 2.5-V, 3-V and 3.3-V
D
Dropout Voltage Down to 170 mV at 200 mA
(TPS7433)
D
3% Tolerance Over Specified Conditions
D
8-Pin SOIC Package
D
Thermal Shutdown Protection
description
This device is designed to have a fast transient response and be stable with 1-µF capacitors. This combination
provides high performance at a reasonable cost.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 170 mV
at an output current of 200-mA for the TPS7433). This LDO family also features a sleep mode; applying a TTL
high signal to EN (enable) shuts down the regulator, reducing the quiescent current to less than 1 µA at
TJ = 25°C.
The TPS74xx is offered in 1.5-V, 1.8-V, 2.5-V, 3-V, and 3.3-V. Output voltage tolerance is specified as a
maximum of 3% over line, load, and temperature ranges. The TPS74xx family is available in 8 pin SOIC
package.
–50
200
50
0
100
0
t – Time – µs
CO = 10 µF
TPS7418
LOAD TRANSIENT RESPONSE
0 300200100 400 500 700600 800 900 1000
I – Output Current – mA
O
V
O
– Change in
∆
Output Voltage – mV
di/dt =
TJ – Junction Temperature – °C
100
0
150
50
–50
300
200
250
– Dropout Voltage – mV
V
DO
TPS7433
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
–25 250 50 75 100 125 150
IO = 50 mA
IO = 1 mA
IO = 75 mA
IO = 200 mA
VI = 3.2 V
200 mA
25 µs
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright 1999, Texas Instruments Incorporated
1
2
3
4
8
7
6
5
EN
NC
NC
IN
SENSE
OUT
GND
IN
D PACKAGE
(TOP VIEW)
NC – No internal connection
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
AVAILABLE OPTIONS
OUTPUT VOLTAGE
(V)
PACKAGED DEVICES
T
J
TYP
SOIC
(D)
3.3 TPS7433D
3 TPS7430D
–40°C to 125°C
2.5 TPS7425D
1.8 TPS7418D
1.5 TPS7415D
The D package is available taped and reeled. Add an R suffix to the device type (e.g.,
TPS7433DR).
†
See application information section for capacitor selection details.
OUT
4
1
IN
EN
GND
6
8
7
V
I
1 µF
ESR
V
O
1 µF
+
TPS74xx
C
O
†
IN
5
SENSE SENSE
Figure 1. Typical Application Configuration
functional block diagram
_
+
V
ref
OUT
EN
GND
R1
R2
IN
SENSE
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
NAME NO.
I/O
DESCRIPTION
EN 1 I Enable input
GND 6 Regulator ground
IN 4, 5 I Input voltage
NC 2, 3 Not connected
OUT 7 O Regulated output voltage
SENSE 8 I Sense
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Ĕ
Input voltage range‡, VI –0.3 V to 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage range at EN
–0.3 V to VI + 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peak output current Internally limited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See dissipation rating tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature range, TJ –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡
All voltage values are with respect to network terminal ground.
DISSIPATION RATING TABLE 1 – FREE-AIR TEMPERATURES
PACKAGE
AIR FLOW
(CFM)
TA < 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
0 568 mW 5.68 mW/°C 312 mW 227 mW
D
250 904 mW 9.04 mW/°C 497 mW 361 mW
recommended operating conditions
MIN MAX UNIT
Input voltage, V
I
§
2.5 7 V
Output current, IO (see Note 1) 0 200 mA
Operating virtual junction temperature, TJ (see Note 1) –40 125 °C
§
To calculate the minimum input voltage for your maximum output current, use the following equation: V
I(min)
= V
O(max)
+ V
DO(max load)
.
NOTE 1: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range,
V
i
= V
O(typ)
+ 1 V, I
O
= 1 mA, EN = 0 V, CO = 1 µF (unless otherwise noted)
PARAMETER TEST CONDITIONS TEST CONDITIONS MIN TYP MAX UNIT
TJ = 25°C 1.5
TPS7415
2.5 V
<
V
I
< 7
V
TJ = –40°C to 125°C 1.455 1.545
TJ = 25°C 1.8
TPS7418
2.8 V
<
V
I
< 7
V
TJ = –40°C to 125°C 1.746 1.854
Output voltage (10 µA to 200 mA load)
TJ = 25°C 2.5
g( µ )
(see Note 2)
TPS7425
3.5 V
<
V
I
< 7
V
TJ = –40°C to 125°C 2.425 2.575
V
TJ = 25°C 3.0
TPS7430
4.0 V
<
V
I
< 7
V
TJ = –40°C to 125°C 2.910 3.090
TJ = 25°C 3.3
TPS7433
4.3 V
<
V
I
< 7
V
TJ = –40°C to 125°C 3.201 3.399
TJ = 25°C 80
I
O
= 1 mA, EN = 0
V
TJ = –40°C to 125°C 115
µ
A
TJ = 25°C 550
Quiescent current (GND current) (See Note 2)
I
O
=
100 mA
, EN = 0
V
TJ = –40°C to 125°C 850
µ
A
TJ = 25°C 1300
I
O
=
200 mA
, EN = 0
V
TJ = –40°C to 125°C 1500
µ
A
Output voltage line regulation (∆VO/V
O
)
(see Notes 2 and 3)
VO + 1 V < VI ≤ 7 V, TJ = 25°C 0.06 %/V
Load regulation 5 mV
Output noise voltage
BW = 300 Hz to 50 kHz,
TJ = 25°C
CO = 1 µF,
190 µVrms
Output current Limit VO = 0 V 500 750 mA
Thermal shutdown junction temperature 150 °C
2.5 V < VI < 7 V,
TJ = 25°C
EN = V
I,
1 µA
Standby current
2.5 V < VI < 7 V,
TJ = –40°C to 125°C
EN = V
I,
3 µA
High level enable input voltage 2 V
Low level enable input voltage 0.7 V
p
EN = 0 V –1 1
Input current (EN)
EN = V
I
–1 1
µ
A
Power supply ripple rejection (see Note 2)
f = 100 Hz,
TJ = 25°C
CO = 1 µF,
55 dB
IO = 200 mA, TJ = 25°C 180
p
TPS7430
IO = 200 mA, TJ = –40°C to 125°C 350
Dropout voltage (see Note 4)
IO = 200 mA, TJ = 25°C 170
mV
TPS7433
IO = 200 mA, TJ = –40°C to 125°C 315
NOTES: 2. Minimum IN operating voltage is 2.5 V or V
O(typ)
+ 1 V, whichever is greater. Maximum IN voltage 7 V.
3. If VO = 1.5 V then V
imax
= 7 V, V
imin
= 2.5 V:
4. IN voltage equals VO(Typ) – 100 mV; TPS7430 and TPS7433 dropout limited by input voltage range limitations (i.e., TPS7430 input
voltage needs to drop to 2.9 V for purpose of this test).
Line Reg. (mV)
+ǒ%ńVǓ
V
O
ǒ
V
imax
*
2.5 V
Ǔ
100
1000
If VO ≥ 2.5 V then V
imax
= 7 V, V
imin
= VO + 1 V:
Line Reg. (mV)
+ǒ%ńVǓ
V
O
ǒ
V
imax
*ǒVO)
1V
Ǔ
Ǔ
100
1000
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Table of Graphs
FIGURE
p
vs Output current 2, 3, 4
VOOutput voltage
vs Junction temperature 5, 6
Ground current vs Junction temperature 7, 8
Power supply ripple rejection vs Frequency 12
Output noise vs Frequency 9
Z
o
Output impedance vs Frequency 10
V
DO
Dropout voltage vs Junction temperature 11
Line transient response 13, 15
Load transient response 14, 16
Output voltage vs Time 17
(Stability) Equivalent series resistance (ESR) vs Output current 19
TYPICAL CHARACTERISTICS
Figure 2
IO – Output Current – mA
TPS7418
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
50 100
1.805
1.800
1.795
150 250
1.810
0 200
– Output Voltage – V
V
O
VI = 2.8 V
TA = 25°C
Figure 3
IO – Output Current – mA
3.300
50 100 150 250
3.310
0 200
VI = 4.3 V
TA = 25°C
– Output Voltage – V
V
O
TPS7433
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
3.305
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 4
IO – Output Current – mA
TPS7425
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
2.49
50 100
2.5
2.496
150 2500 200
– Output Voltage – V
V
O
VI = 3.5 V
TA = 25°C
2.498
2.494
2.492
Figure 5
TJ – Junction Temperature – °C
TPS7418
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
1.806
1.802
1.816
1.812
1.820
– Output Voltage – V
V
O
1.818
1.814
1.810
1.808
1.804
–50
–25 250 50 75 100 125 150
IO = 50 mA
IO = 100 mA
IO = 1 mA
VI = 4.0 V
IO = 200 mA
Figure 6
TJ – Junction Temperature – °C
TPS7433
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
3.285
3.330
3.305
3.315
– Output Voltage – V
V
O
3.325
3.320
3.310
3.300
3.295
3.290
–50
–25 250 50 75 100 125 150
VI = 4.3 V
IO = 1 mA
IO = 50 mA
IO = 100 mA
IO = 200 mA
Figure 7
TJ – Junction Temperature – °C
100
1
0 150
10000
–50 50
1000
VI = 2.8 V
100
IO = 1 mA
TPS7418
GROUND CURRENT
vs
JUNCTION TEMPERATURE
Ground Current – Aµ
IO = 200 mA
IO = 100 mA
10
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 8
TJ – Junction Temperature – °C
0
150
–50 50
VI =4.3 V
100
IO = 1 mA
TPS7433
GROUND CURRENT
vs
JUNCTION TEMPERATURE
Ground Current – Aµ
100
1
10000
1000
IO = 200 mA
10
IO = 100 mA
Figure 9
f – Frequency – Hz
1k 10k 100k
250
Output Spectral Noise Density
IO = 1 mA
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
2nV Hz
Ǹ
20nV Hz
Ǹ
200nV Hz
Ǹ
2µVHz
Ǹ
20µVHz
Ǹ
IO = 200 mA
VI = 4.3 V
CL = 1 µF
TA = 25°C
Figure 10
0.1
0.1 1 1000
10
0.01 10
1
f – Frequency – kHz
100
– Output Impedance –Z
o
Ω
OUTPUT IMPEDANCE
vs
FREQUENCY
VI = 4.3 V
CL = 1 µF
TA = 25°C
CL = 1 µF:
IO = 1 mA
CL = 1 µF
IO = 200 mA
100
0.01
Figure 11
TJ – Junction Temperature – °C
100
0
10
150
50
110–40 60
200
250
VI = 2.9 V
– Dropout Voltage – mV
V
DO
TPS7430
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
200 mA
100 mA
10 mA
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
f – Frequency – Hz
100 1k 10k10
Ripple Rejection – dB
RIPPLE REJECTION
vs
FREQUENCY
0
20
40
60
80
50
70
30
10
100k 1M 10M
CL = 1 µF
IO = 100 mA
CL = 1 µF
IO = 1 mA
CL = 1 µF
IO = 200 mA
Figure 12
Figure 13
V
O
– Change in
–200
3.8
–300
2.8
200
0
TPS7418
LINE TRANSIENT RESPONSE
V
I
t – Time – ms
0 0.30.20.1 0.4 0.5 0.70.6 0.8 0.9 1
CO = 1 µF
– Input Voltage – V
∆
Output Voltage – mV
Figure 14
–50
200
50
0
100
0
t – Time – ms
CO = 10 µF
TPS7418
LOAD TRANSIENT RESPONSE
0 0.30.20.1 0.4 0.5 0.70.6 0.8 0.9 1
I – Output Current – mA
O
V
O
– Change in
∆
Output Voltage – mV
200 mA
25 µs
di/dt =
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 15
–200
5.3
4.3
200
0
TPS7433
LINE TRANSIENT RESPONSE
t – Time – ms
0 0.30.20.1 0.4 0.5 0.70.6 0.8 0.9 1
CO = 1 µF
V
O
– Change in
V
I
– Input Voltage – V
∆
Output Voltage – mV
Figure 16
–50
200
50
0
100
0
0
CO = 10 µF
TPS7433
LOAD TRANSIENT RESPONSE
I – Output Current – mA
O
V
O
– Change in
∆
Output Voltage – mV
–50
200 mA
25 µs
di/dt =
t – Time – ms
0 0.30.20.1 0.4 0.5 0.70.6 0.8 0.9 1
t – Time – ms
TPS7433
OUTPUT VOLTAGE
vs
TIME (AT STARTUP)
4
2
0.60.40.2 0.8 1 1.41.2 1.6 1.8 20
V
O
– Output Voltage – V
5
0
Enable Pulse – V
0
VI = 7 V
Figure 17
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
IN
EN
OUT
+
GND
C
O
ESR
R
L
V
I
To Load
Figure 18. Test Circuit for Typical Regions of Stability (Figure 19)
0.1
0.01
0 50 100 150 200
TYPICAL REGIONS OF STABILITY
EQUIVALENT SERIES RESISTANCE (ESR)
†
vs
OUTPUT CURRENT
10
100
IO – Output Current – mA
ESR – Equivalent Series Resistance –
Ω
1
Region of Instability
Figure 19
†
ESR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally , and PWB trace resistance
to CO.
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
The TPS74xx family includes five voltage regulators (1.5 V, 1.8 V, 2.5 V, 3 V, and 3.3 V).
minimum load requirements
The TPS74xx family is stable even at zero load; no minimum load is required for operation.
SENSE terminal connection
The SENSE terminal must be connected to the regulator output for proper functioning of the regulator . Normally,
this connection should be as short as possible; however, the connection can be made near a critical circuit
(remote sense) to improve performance at that point. Internally, SENSE connects to a high-impedance
wide-bandwidth amplifier through a resistor-divider network and noise pickup feeds through to the regulator
output. Routing the SENSE connection to minimize/avoid noise pickup is essential. Adding an RC network
between SENSE and OUT to filter noise is not recommended because it can cause the regulator to oscillate.
external capacitor requirements
An input capacitor is not usually required; however, a ceramic bypass capacitor (1 µF or larger) improves load
transient response and noise rejection if the TPS74xx is located more than a few inches from the power supply .
A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load transients
with fast rise times are anticipated.
Like all low dropout regulators, the TPS74xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance value is 1 µF and the ESR
(equivalent series resistance) must be at least 300 mΩ. Solid tantalum electrolytic and aluminum electrolytic
are all suitable, provided they meet the requirements described previously.
OUT
4
1
IN
EN
GND
6
8
7
V
I
1 µF
ESR
V
O
1 µF
+
TPS74xx
C
O
IN
5
SENSE SENSE
Figure 20. Typical Application Circuit
regulator protection
The TPS74xx PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
regulator protection (continued)
The TPS74xx also features internal current limiting and thermal protection. During normal operation, the
TPS74xx limits output current to approximately 500 mA. When current limiting engages, the output voltage
scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross
device failure, care should be taken not to exceed the power dissipation ratings of the package. If the
temperature of the device exceeds 150°C(typ), thermal-protection circuitry shuts it down. Once the device has
cooled below 130°C (typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. T o ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, P
D(max)
, and the actual dissipation, PD, which must be less than
or equal to P
D(max)
.
The maximum-power-dissipation limit is determined using the following equation:
P
D(max)
+
TJmax*T
A
R
q
JA
Where
TJmax is the maximum allowable junction temperature.
T
A
is the ambient temperature.
R
θJA
is the thermal resistance junction-to-ambient for the package, i.e., 172°C/W for the 8-terminal
SOIC.
The regulator dissipation is calculated using:
PD+ǒVI*
V
O
Ǔ
I
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
TPS7415, TPS7418, TPS7425, TPS7430, TPS7433
FAST-TRANSIENT-RESPONSE USING SMALL OUTPUT CAPACITOR
200-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS212 – DECEMBER 1999
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
4040047/B 03/95
0.228 (5,80)
0.244 (6,20)
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
1
14
0.014 (0,35)
0.020 (0,51)
A
0.157 (4,00)
0.150 (3,81)
7
8
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.010 (0,25)
PINS **
0.008 (0,20) NOM
A MIN
A MAX
DIM
Gage Plane
0.189
(4,80)
(5,00)
0.197
8
(8,55)
(8,75)
0.337
14
0.344
(9,80)
16
0.394
(10,00)
0.386
0.004 (0,10)
M
0.010 (0,25)
0.050 (1,27)
0°–8°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Four center pins are connected to die mount pad.
E. Falls within JEDEC MS-012
IMPORTANT NOTICE
T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERT AIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICA TIONS IS UNDERSTOOD T O
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
Loading...