
Evaluation Kit Features
• Two TAS5733LEVM digital input Class-D audio ampliers -
one in stereo and one in mono conguration
• Robust design with outstanding thermal performance
• Wide supply voltage capabilities, from 8V to 16.5V
• Versatile input selection via PurePath
TM
Console Mother Board
• Easy conguration and evaluation using PurePath Console
Graphical User Interface
2

Getting Started
1. Request access to the TAS5733LEVM app from
ti.com/tool/TAS5733LEVM. Allow 1-2 days for approval.
2. PurePath™ Console Software is required to evaluate the TAS5733LEVM.
Order here: ti.com/tool/purepathconsole
PurePath Console Motherboard is the primary interface between the
PurePath Console and TAS5733LEVM.
Order here: ti.com/tool/purepath-cmbevm
3. Connect the evaluation module with PurePath Console Motherboard
as indicated.
4. Connect the power supply to the binding posts of the evaluation
module. A regulator on the motherboard provides the required 3.3V
for the ampliers.

Getting Started cont.
5. A micro USB cable is required to connect the evaluation module
with the PC.
6. Download and install PurePath™ Console Software
from: ti.com/mysecuresoftware
7. Sign into PurePath Console. Install the app for the TAS5733L.
8. Open the app, then select Hardware Checks window to perform
system diagnosis.
9. Select the desired audio source on the audio I/O window.
10. Open Audio Processing window and wait for the devices to
get congured.
11. Start playing audio and enjoy the evaluation of the TAS5733LEVM!
12. For more information, refer to the TAS5733LEVM
User’s Guide: ti.com/lit/slou439
4

Features and Benefits
3-Band AGL
The multiband AGL is used
as a three-band crossover,
having an independent custom
conguration available for low,
high, and mid frequency bands.
Single-filter PBTL support
The device supports the use of
only one output lter for mono
applications by tying OUT_A
with OUT_B, and tying OUT_C
with OUT_D.
Good thermal performance
The robust design of the
evaluation module allows the
amplier to deliver up to 25W
output power in stereo mode
without thermal issues.
Low cost
The reduced BOM and smaller
PCB footprint for the device and
supporting components reduces
the system cost.
Easy to use
The conguration via PPC allows easy
integration with any system.
The TAS5733L can operate after
conguring three basic registers:
#Enable internal oscillator
Reg 0x1B, 0x00
#Exit shutdown
Reg 0x05, 0x00
#Unmute and set volume to 0dB
Reg 0x07, 0x00 C0

Design Resources and References
Engage in the
Audio Amplifiers Support Forum
TM
Available on: ti.com/product/TAS5733L
• TAS5733L datasheet
• Complete TAS5733LEVM User’s Guide
• Schematics and layout
• EVM Source code and binaries
Search for solutions, get help and share
knowledge with fellow engineers
Get more information on TI’s solutions for audio
applications at ti.com/audio
• New Products
• Technical Documents
• Support and Training
• Product Selection Tool
Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are
sold subject to TI’s standard terms and conditions of sale. Customers are advised to obtain the most current and complete
information about TI products and services before placing orders. TI assumes no liability for applications assistance,
customer’s applications or product designs, software performance, or infringement of patents. The publication of information
regarding any other company’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
The platform bar, E2E, and PurePath are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
SLOU445

IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated