Texas Instruments SN74LVC1GU04DBVR, SN74LVC1GU04DCKR Datasheet
SN74LVC1GU04
SINGLE INVERTER
SCES215B – APRIL 1999 – REVISED AUGUST 1999
D
EPIC
(Enhanced-Performance Implanted
CMOS) Submicron Process
D
Unbuffered Output
D
I
Feature Supports Partial-Power-Down
off
Mode Operation
D
Supports 5-V VCC Operation
D
Package Options Include Plastic
DBV OR DCK PACKAGE
(TOP VIEW)
NC
1
A
2
GND
NC – No internal connection
3
V
5
CC
Y
4
Small-Outline Transistor (DBV, DCK)
Packages
description
This single inverter is designed for 1.65-V to 5.5-V VCC operation.
The SN74L VC1GU04 contains one inverter with an unbuffered output, and performs the Boolean function Y = A.
This device is fully specified for partial-power-down applications using I
preventing damaging current backflow through the device when it is powered down.
The SN74LVC1GU04 is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
INPUT
OUTPUT
A
H L
L H
Y
off
. The I
circuitry disables the outputs,
off
logic symbol
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
†
2
A
1
logic diagram (positive logic)
24
AY
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
4
Y
PRODUCT PREVIEW
EPIC is a trademark of Texas Instruments Incorporated.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 1999, Texas Instruments Incorporated
1
SN74LVC1GU04
VCCSuppl
oltage
V
VIHHigh-level input voltage
V
VILLow-level input voltage
V
SINGLE INVERTER
SCES215B – APRIL 1999 – REVISED AUGUST 1999
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC –0.5 V to 6.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (see Note 1) –0.5 V to 6.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage range, V
(see Notes 1 and 2) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
Input clamp current, IIK (VI < 0) –50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output clamp current, IOK (VO < 0) –50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous current through VCC or GND ±100 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θ
(see Note 3): DBV package 347°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JA
DCK package 389°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The value of VCC is provided in the recommended operating conditions table.
3. The package thermal impedance is calculated in accordance with JESD 51.
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
recommended operating conditions
MIN MAX UNIT
pp
y v
p
p
V
PRODUCT PREVIEW
V
I
OH
I
OL
∆t/∆v Input transition rise or fall rate
T
Input voltage 0 5.5 V
I
Output voltage 0 V
O
High-level output current
Low-level output current
Operating free-air temperature –40 85 °C
A
Operating 1.65 5.5
Data retention only 1.5
VCC = 1.65 V to 1.95 V 0.65 × V
VCC = 2.3 V to 2.7 V 1.7
VCC = 2.7 V to 3.6 V 2
VCC = 4.5 V to 5.5 V 0.7 × V
VCC = 1.65 V to 1.95 V 0.35 × V
VCC = 2.3 V to 2.7 V 0.7
VCC = 2.7 V to 3.6 V 0.8
VCC = 4.5 V to 5.5 V 0.3 × V
VCC = 1.65 V –4
VCC = 2.3 V –8
VCC = 2.7 V
VCC = 3 V –24
VCC = 4.5 V –32
VCC = 1.65 V 4
VCC = 2.3 V 8
VCC = 2.7 V
VCC = 3 V 24
VCC = 4.5 V 32
VCC = 1.8 V ± 0.15 V, 2.5 V ± 0.2 V 20
VCC = 3.3 V ± 0.3 V
VCC = 5 V ± 0.5 V 5
CC
CC
CC
–12
12
10
CC
CC
†
V
mA
mA
ns/V
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
V
V
V
V
(INPUT)
(OUTPUT)
PARAMETER
TEST CONDITIONS
UNIT
SN74LVC1GU04
SINGLE INVERTER
SCES215B – APRIL 1999 – REVISED AUGUST 1999
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER TEST CONDITIONS V
IOH = –100 mA 1.65 V to 5.5 V VCC–0.1
IOH = –4 mA 1.65 V 1.2
OH
OL
I
I
I
off
I
CC
∆I
CC
C
†
All typical values are at VCC = 3.3 V, TA = 25°C.
i
IOH = –8 mA 2.3 V 1.9
IOH = –12 mA 2.7 V 2.2
IOH = –24 mA
IOH = –32 mA
IOL = 100 mA 1.65 V to 5.5 V 0.1
IOL = 4 mA 1.65 V 0.45
IOL = 8 mA 2.3 V 0.3
IOL = 12 mA 2.7 V 0.4
IOL = 24 mA
IOL = 32 mA
VI = 5.5 V or GND 0 to 5.5 V ±5
VI or VO = 5.5 V 0 ±10
VI = 5.5 V or GND, IO = 0 1.65 V to 5.5 V 10
One input at VCC – 0.6 V,
Other inputs at VCC or GND
VI = VCC or GND 3.3 V pF
CC
3 V 2.3
4.5 V 3.8
3 V 0.55
4.5 V 0.55
2.7 V to 5.5 V 500
MIN TYP†MAX UNIT
m
A
m
A
m
A
m
A
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figures 1 through 4)
PARAMETER
t
pd
FROM
A
TO
operating characteristics, T
C
Power dissipation capacitance f = 10 MHz pF
pd
Y
= 25°C
A
VCC = 1.8 V
± 0.15 V
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
VCC = 2.5 V
± 0.2 V
VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V VCC = 5 V
VCC = 2.7 V
TYP TYP TYP TYP
VCC = 3.3 V
± 0.3 V
VCC = 5 V
± 0.5 V
UNIT
ns
PRODUCT PREVIEW
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
Loading...