Texas Instruments MRD2EVM User Manual

Download

MRD2EVM Microreader Evaluation Kit

User's Guide

Literature Number: SCBU050

July 2012

Contents

1 Microreader Overview .......................................................................................................... 4

2 Kit Contents ....................................................................................................................... 5

3 Download the Software ........................................................................................................ 6

4 Installation ......................................................................................................................... 6

4.1 Driver Installation ........................................................................................................ 6

4.2 RI-STU-MRD2 Demo Software (GUI) Installation ................................................................... 9

5 RI-STU-MRD2 Demo Software (GUI) Introduction .................................................................... 9

6 Demo Examples ................................................................................................................ 10

6.1 Demo 1: Read or Write LF Transponder (Read Only/ Read Write) – Tab 1 ................................... 10

6.2 Demo 2: Read or Write LF Transponder (MPT 16/17) – Tab 1 .................................................. 11

6.3 Demo 3: HDX+ Transponder (Read or Write Memory) – Tab 1 ................................................. 12

6.4 Demo 4: OTP Transponder (Read or Write ID) – Tab 2 .......................................................... 13

6.5 Demo 5: HDX+ Transponder (Read or Write ID) – Tab 2 ........................................................ 14

6.6 Demo 6: HDX+ Transponder (Trim Frequency) – Tab 2 ......................................................... 15

6.7 Demo 7: HDX+ Transponders (Inventory Command) – Tab 3 ................................................... 16

6.8 Demo 8: PaLFI (Read, Write, Battery Charge and Check, and Flash LED) – Tab 4 ......................... 17

7 Schematics ....................................................................................................................... 18

7.1 RI-STU-MRD2 EVM Board ........................................................................................... 18

Table of Contents SCBU050–July 2012

Submit Documentation Feedback

www.ti.com

1 RI-STU-MRD2 EVM Board ................................................................................................ 4

2 MRD2EVM Carton Box With Contents................................................................................... 5

3 Windows Security........................................................................................................... 6

4 Driver Installed Successfully............................................................................................... 6

5 New Hardware Wizard, Step 1............................................................................................ 7

6 New Hardware Wizard, Step 2............................................................................................ 7

7 New Hardware Wizard, Step 3............................................................................................ 8

8 New Hardware Wizard, Step 4............................................................................................ 8

9 RI-STU-MRD2 Demo Software (GUI): Startup Screen ................................................................ 9

10 Read or Write LF Transponder (Type: Read-Only or Read/Write).................................................. 10

11 Read or Write LF Transponder (Type: MPT 16/17)................................................................... 11

12 Read or Write Memory Content of HDX+ Transponder.............................................................. 12

13 Read or Write ID of OTP Transponder ................................................................................. 13

14 Read or Write ID of HDX+ Transponder ............................................................................... 14

15 Trim Resonance Frequency of HDX+ Transponder .................................................................. 15

16 Read Inventory of HDX+ Transponder ................................................................................. 16

17 Read, Write, Battery Charge, Battery Check, and Flash LED of PaLFI............................................ 17

18 RI-STU-MRD2 EVM Board Schematic ................................................................................. 18

List of Figures

List of Tables

1 Kit Contents.................................................................................................................. 5

2 GUI Tabs..................................................................................................................... 9

SCBU050–July 2012 List of Figures

Submit Documentation Feedback

User's Guide

SCBU050–July 2012

MRD2EVM Microreader Evaluation Kit

WARNING

The terminals across the antenna connectors SJ1 and SJ2, the through-hole contact below mark R6-->R7, and the through-hole contacts 16 and 19 of CON3 operate at potentially hazardous voltages. Effective safety application procedures and knowledge are required to minimize risk of electrical shock hazard when using this EVM. The user should be technically qualified to operate this EVM, including having full knowledge of risks associated in working with electrically live and hazardous voltages commonly found in development platforms. Careful review of General Texas

Instruments High Voltage Evaluation Module (TI HV EVM) User Safety Guidelines at the end of this document is required prior to using

this EVM.

1 Microreader Overview

The microreader evaluation board (RI-STU-MRD2) is a complete USB-based reader module providing the hardware and software to communicate with TI's low-frequency (LF), half-duplex (HDX), and advanced transponders for programming and tuning after the production phase.

The USB reader-writer stick contains the RI-STU-MRD2 DIL module, which is mounted on an antenna base board with a USB connector. The RI-STU-MRD2 is backward compatible with the RS232 based RISTU-MRD1 reader module.

Figure 1. RI-STU-MRD2 EVM Board

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Submit Documentation Feedback

www.ti.com

The main features of the RI-STU-MRD2 are:

• RS232 and USB interfaces

• Multi-purpose I/Os

• Low-power operation (2.7 V to 5.5 V)

• Supports programming and tuning of advanced transponders

• Easy to design in and use

2 Kit Contents

Kit Contents

Figure 2. MRD2EVM Carton Box With Contents

Pos Ref Des Part Type

1 Box Carton Box MSP430 2 Foam Foam Protection

3 Samples Samples

4 Carrier Board PCB MRD2EVM V2.0 5 Microreader RI-STU-MRD2 6 Manual 11-06-21-073 7 Label

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

Table 1. Kit Contents

Order or Specification

Number

RI-TRP-DR2B-30 RI-TRP-RR2B-30

RI-TRP-WR2B-30

RI-TRP-RR3P-30

RI-TRP-WR3P-30

TRPGR30TGC

RI-TRP-R9QL-30

RI-TRP-W9QL-30

Download the Software

3 Download the Software

Download the latest version of the following files:

1. RI-STU-MRD2 reference manual: SCBU049

2. RI-STU-MRD2 demo software (GUI): xxxxxx

3. USB device driver: xxxxx

4. Additional documents, such as application reports and white papers: http://www.ti.com/rfid

5. RI-STU-MRD2 product folder: http://www.ti.com/tool/RI-STU-MRD2

4 Installation

4.1 Driver Installation

1. Download the driver from the link specified in 3.Download the software.

2. Proceed according to the type of Operating system.

4.1.1 Windows 7 or Later

1. Remove the RI-STU-MRD2 EVM board if it is already connected to USB Port.

2. Right click on the driver file and click INSTALL.

3. Click YES if Windows prompts for authentication from User Account Control.

4. Click "Install this driver software anyway", if Windows prompts for authentication.

www.ti.com

5. Connect the reader. After installation is complete, the message shown in Figure 4 is displayed.

6. The USB driver is now installed on the PC, and the system is ready for use.

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Figure 3. Windows Security

Figure 4. Driver Installed Successfully

Submit Documentation Feedback

www.ti.com

4.1.2 Windows XP

1. Connect the RI-STU-MRD2 EVM to USB port. When the window shown in Figure 5 is displayed, click "Yes, this time only" and then click Next.

Installation

Figure 5. New Hardware Wizard, Step 1

2. When the window shown in Figure 6 is displayed, click "Install from a list or Specific location" and then click Next.

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

Figure 6. New Hardware Wizard, Step 2

Installation

3. When the window shown in Figure 7 is displayed, click Browse, select the location of the downloaded

www.ti.com

driver file on the PC, and then click Next.

Figure 7. New Hardware Wizard, Step 3

4. If Windows prompts for authentication, continue with the installation. After successful installation, the window shown in Figure 8 is displayed. Click Finish.

5. The USB driver is now installed on the PC, and the system is ready to use.

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Figure 8. New Hardware Wizard, Step 4

Submit Documentation Feedback

Tab 1 Tab 2 Tab 3

COM Port data with version

Tab 4 Tab 5

www.ti.com

4.2 RI-STU-MRD2 Demo Software (GUI) Installation

Download the driver from the link specified in 3.Download the software

1. Unpack RI-STU-MRD2 Demo Software.zip.

2. Double click the RI-STU-MRD2 Demo Reader Software.exe.

5 RI-STU-MRD2 Demo Software (GUI) Introduction

The RI-STU-MRD2 demo Software supports simple reading/programming of LF HDX, HDX+, Advanced HDX+ and PaLFI Transponders. When the reader connects to the USB port, the software automatically detects the reader and the COM port data is displayed on the top as shown in below in Figure 9. The five tabs described in Table 2 define use mode depending on type of transponders.

Table 2. GUI Tabs

Tab Name Contents and Functions

1 LF / HDX+ Read or write LF tags (R/O, R/W, or MPT 16 /17); read or write memory of HDX+ tags 2 Read or write ID; HDX+ tag read or write ID and tune resonance frequency 3 HDX+ Inventory Inventory process (read aids of group of HDX+ transponders)

4 PaLFI Transponder Read, write, battery check, battery charge, MSP access 5 About Software and hardware version of the RI-STU-MRD2 reader

The initial screen view with the tabs and COM port data is shown in Figure 9.

OTP/HDX+

Programming/Tuning

RI-STU-MRD2 Demo Software (GUI) Introduction

Figure 9. RI-STU-MRD2 Demo Software (GUI): Startup Screen

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

Demo Examples

6 Demo Examples

6.1 Demo 1: Read or Write LF Transponder (Read Only/ Read Write) – Tab 1

www.ti.com

Figure 10. Read or Write LF Transponder (Type: Read-Only or Read/Write)

1 Check Tag Type button: Shows the tag type at position 4 (Transponder Type). 2 Read Tag button: Reads transponder data, depending on the transponder type.

For read only and read/write transponder types, shows LF-8 byte data with 2-byte CRC and data at position 6 of Figure 10. For MPT 16/17 types, shows 16/17 pages with each page of 8-byte data and 2-byte CRC at position 10 of Figure 11. For HDX+ types, shows 16 pages of 4-byte data at position 12 of Figure 12.

3 Write Tag button: Programs the transponder, depending on the transponder type.

For LF-R/W type transponders, writes 8-byte data with 2-byte CRC (or) 10-byte data. Data can be edited at position 6 of Figure 10 as described in position 6, below. For MPT 16/17 type transponders, writes 16/17 pages with each page of 8-byte date and 2-byte CRC. Data can be edited at position 10 of Figure 11 as described in Section 6.2. For HDX+ type transponders, writes 16 pages of 4-byte data. Data can be edited at position 12 of

Figure 12 as described in Section 6.3.

4 Shows the type of the transponder. If no transponder is found, "no transponder detected" is shown. 5 Shows the status (success or error) of the most recent activity. 6 Shows the 10-byte data field (8-byte ID and 2-byte CRC) of the LF Transponder (R/O or R/W) in

the first row of the table. Data appears after the successful read of transponder.

The Lock column on the right side of table shows the lock status of every single memory row. To

lock the transponder check the Lock box and click Write Tag.

Check the Calc CRC box to write 8-byte data (the CRC is calculated by the reader).

Uncheck the Calc CRC box to write 10-byte data (the CRC is not calculated by the reader). 7 Shows the last 20 commands transmitted to reader. 8 Shows the last 20 commands received from reader. 9 Continuous mode operation check box.

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Submit Documentation Feedback

www.ti.com

6.2 Demo 2: Read or Write LF Transponder (MPT 16/17) – Tab 1

Demo Examples

NOTE: See descriptions of positions 1, 2, 3, 4, 5, 7, 8, and 9 in Figure 10 for additional details.

Figure 11. Read or Write LF Transponder (Type: MPT 16/17)

10 This is the 16/17-page 10-byte data (8-byte data with 2-byte CRC) of the LF Transponder MPT

16/17. Data appears after a successful transponder read.

The Lock column on the right side of the transponder data shows the lock status of every memory

block. To lock the transponder pages, check the Lock box of any page and click Write Tag (see the

description of position 11 for important details of writing to the tag).

Check the Calc CRC box to write 8-byte data (the CRC is calculated by the reader).

Uncheck the Calc CRC box to write 10-byte data (the CRC is not calculated by the reader). 11 Check this box and click Write Tag to write all pages of the MPT 16/17 transponder at one time.

Uncheck this box and click Write Tag to write only the edited page data. If the data has not been

edited, then reader writes the default page 1 data as shown in Figure 10.

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

Demo Examples

6.3 Demo 3: HDX+ Transponder (Read or Write Memory) – Tab 1

www.ti.com

NOTE: See descriptions of positions 1, 2, 3, 4, 5, 7, 8, and 9 in Figure 10 for additional details.

Figure 12. Read or Write Memory Content of HDX+ Transponder

12 This is the 16 page (64 byte) memory data of the HDX+-Transponder shown in grid view table

format. The description of each page is described in column 2 and the corresponding 4 byte data is

displayed in column 3, 4, 5 & 6 of the table as shown in table at position 12. 13 This is the last column of the grid view table that shows the memory status of each page. The

locked pages with orange background are not re-writable. The writable pages with green

background are re-writable.

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Submit Documentation Feedback

www.ti.com

6.4 Demo 4: OTP Transponder (Read or Write ID) – Tab 2

Demo Examples

Figure 13. Read or Write ID of OTP Transponder

1 Click on Read ID (or) Write ID buttons to read (or) write the 64 byte ID with 16 byte CRC to an OTP

transponder. 2 This is the 10 byte data (8 byte ID and 2 byte CRC) of the OTP Transponder shown in grid view

table first row. The Lock column on the right side of the transponder data shows the lock stats of

the ID. To lock the transponder check the Lock box and click Write ID. 3 Decimal field for ISO 11785 animal or industrial code. This automatically converts to 8 byte hex

data in field 2. If hex data is entered in field 2, data automatically converts to decimal data in field 3. 4 Auto increment the ID after successful programming of a transponder. 5 Loads a list of IDs from an Excel® spreadsheet to write a batch of transponders. The Auto Inc ID

checkbox at position 4 needs to be checked to load the subsequent ID from the Excel spreadsheet

after each successful write to the transponder. Click Unload XLS to remove the loaded data.

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

Demo Examples

6.5 Demo 5: HDX+ Transponder (Read or Write ID) – Tab 2

www.ti.com

Figure 14. Read or Write ID of HDX+ Transponder

1 Read ID (or) Write ID button initiates a read (or) write of the 64 byte ID with 16 byte CRC of an

HDX+ transponder. 2 This is the 10 byte data (8 byte ID and 2 byte CRC) of the OTP HDX+ Transponder shown in the

grid view table first row. The Lock column on the right hand side of the transponder data shows the

lock stats of the ID. To lock the transponder check on the Lock checkbox and click on write ID

button. 3 Decimal field for ISO 11785 animal or industrial code. This automatically converts to 8 byte hex

data in field 2. If HEX data is entered in field 2, data automatically converts to decimal data in field

4 Q-value of the transponder. Select the correct Q-value of the transponder and click Write ID to write

to the transponder. 5 Auto increment the ID after successful programming of a transponder. 6 Read or write the resonance frequency of a transponder. The frequency of a transponder is shown

in this field. To set the frequency at the same time of write ID phase, check the Set Frequency box

and type the target frequency in the field. 7 Loads a list of IDs from an Excel® spreadsheet to write a batch of transponders. The Auto Inc ID

checkbox at position 5 needs to be checked to load the subsequent ID from the Excel®

spreadsheet after each successful write to the transponder. Click Unload XLS to remove the loaded

data.

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Submit Documentation Feedback

www.ti.com

6.6 Demo 6: HDX+ Transponder (Trim Frequency) – Tab 2

Demo Examples

Figure 15. Trim Resonance Frequency of HDX+ Transponder

1 Tune or read the frequency of transponder: Click Read Frequency to display the measured

frequency value at position 3 (the default target frequency value is displayed at position 2). 2 Target frequency field in Hz 3 Measured frequency value after each read/write. 4 A valid frequency (128000Hz to 140000Hz) needs to be entered in field 2, the frequency is then

programmed with the Write frequency button.

NOTE: Depending on transponder form factor, the tag needs to be separated from the

antenna by 20 mm to 40 mm to measure and program the correct frequency. The resulting frequency might vary ±500 Hz due to the limited resolution of the internal tuning circuit.

5 Status message field.

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

Demo Examples

6.7 Demo 7: HDX+ Transponders (Inventory Command) – Tab 3

www.ti.com

Figure 16. Read Inventory of HDX+ Transponder

1 Start inventory button: Reads AIDs of a group of advanced HDX+ transponders in the vicinity

region. The list of AIDs of transponders is shown at position 2 of Figure 10. 2 This is the 8 byte ID (8 byte AID) of the HDX+-Transponders detected and shown in each row of

grid view table. The Lock column on the right hand side of the transponder data shows the lock

status of the IDs. 3 A double click on any of ID data in the table initiates a read of the memory content of the selected

transponder.

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Submit Documentation Feedback

www.ti.com

Demo Examples

6.8 Demo 8: PaLFI (Read, Write, Battery Charge and Check, and Flash LED) – Tab 4

Figure 17. Read, Write, Battery Charge, Battery Check, and Flash LED of PaLFI

1 Selection of page number and click on read/write page reads/writes the memory content of the

selected page. 2 The grid view table shows the 5 byte memory content of the selected page. The Lock field on the

right hand side of the memory data shows the lock status of the IDs. 3 Battery Check button: Battery voltage level check of PaLFI. 4 Battery charge status is indicated with 3 different colors orange (low voltage), yellow (medium

voltage) and green (high voltage). 5 Battery charge button: Charge PaLFI module. 6 Flash LED: Selection of the LED color in the field. A click on the flash LED button initiates the

corresponding LED to blink on PaLFI tag which is providing an example for an MSP access

command to the PaLFI tag.

SCBU050–July 2012 MRD2EVM Microreader Evaluation Kit

Submit Documentation Feedback

GND GND

10p 10p

GND

LL103A

100n

33k

27R

GND

RED

GREEN

YELLOW

GND

330R

SWS003

10k

GND

47uH

default:closed

CTB0308

TPD2E001DRLR

GND

default:closed

VBUS

GND

D-

CON1

D+

SHIELD

SHIELD1

C1 C2

SYNC

RDEN-

TEST/SBWTCK

RESET-

RXD

TXD

USB_D-

USB_D+

3_3V_OUT

LF_RX

SIG_OUT_0

SIG_OUT_1

SIG_IN_0

SIG_IN_1

GND

ANT1

ANTCAP

ANT2

GNDP

VSP

USB_PUR

VSL

GND

CRD

WLS

USB_VBUS

OKT

STAT

LED2

LED1

LED3

4 5 61

L1_PRINTED_INDUCTOR

CON2

CON3

SJ1

SJ2

CTB0308-1

CTB0308-2

VCC

IO1

IO2

GND

IC1

SJ3

USB_DP

USB_DM

VBUS

1 2 3

IC2 MRDII DIL MODUL

Schematics

7 Schematics

7.1 RI-STU-MRD2 EVM Board

www.ti.com

MRD2EVM Microreader Evaluation Kit SCBU050–July 2012

Figure 18. RI-STU-MRD2 EVM Board Schematic

Submit Documentation Feedback

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions: The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims

arising from the handling or use of the goods. Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from

the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein.

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada. Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

【【Important Notice for Users of this Product in Japan】】

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:

1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan,

2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this product, or

3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

Texas Instruments Japan Limited

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

http://www.tij.co.jp

【ご使用にあたっての注】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社東京都新宿区西新宿６丁目２４番１号西新宿三井ビル

http://www.tij.co.jp

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished

electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees, affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates, contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard.

3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development environments should use these EVMs.

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate Assurance and Indemnity Agreement.

General Texas Instruments High Voltage Evaluation Module (TI HV EVM) User Safety Guidelines

WARNING

Always follow TI's set-up and application instructions, including use of all interface components within their recommended electrical rated voltage and power limits. Always use electrical safety precautions to help ensure your personal safety and the safety of those working around you. Contact TI's Product Information Center http://support.ti.com for further information.

Save all warnings and instructions for future reference. Failure to follow warnings and instructions may result in personal injury, property damage, or death due to electrical shock and burn hazards.

The term TI HV EVM refers to an electronic device typically provided as an open framed, unenclosed printed circuit board assembly. It is

intended strictly for use in development laboratory environments, solely for qualified professional users having training, expertise and knowledge of electrical safety risks in development and application of high voltage electrical circuits. Any other use and/or application are strictly prohibited by Texas Instruments. If you are not suitable qualified, you should immediately stop further use of the TI HV EVM.

1. Work Area Safety:

(a) Keep work area clean and orderly. (b) Qualified observer(s) must be present any time circuits are energized. (c) Effective barriers and signage must be present in the area where the TI HV EVM and its interface electronics are energized,

indicating operation of accessible high voltages may be present, for the purpose of protecting inadvertent access.

(d) All interface circuits, power supplies, evaluation modules, instruments, meters, scopes, and other related apparatus used in a

development environment exceeding 50Vrms/75VDC must be electrically located within a protected Emergency Power Off

(EPO) protected power strip. (e) Use a stable and nonconductive work surface. (f) Use adequately insulated clamps and wires to attach measurement probes and instruments. No freehand testing whenever

possible.

2. Electrical Safety: As a precautionary measure, it is always a good engineering practice to assume that the entire EVM may have fully accessible and

active high voltages. (a) De-energize the TI HV EVM and all its inputs, outputs, and electrical loads before performing any electrical or other diagnostic

measurements. Revalidate that TI HV EVM power has been safely de-energized.

(b) With the EVM confirmed de-energized, proceed with required electrical circuit configurations, wiring, measurement equipment

hook-ups, and other application needs, while still assuming the EVM circuit and measuring instruments are electrically live.

While the EVM is energized, never touch the EVM or its electrical circuits as they could be at high voltages capable of causing electrical shock hazard.

3. Personal Safety: (a) Wear personal protective equipment; for example, latex gloves or safety glasses with side shields or protect EVM in an

adequate lucent plastic box with interlocks from accidental touch.

Limitation for safe use: EVMs are not to be used as all or part of a production unit.

WARNING

Texas Instruments MRD2EVM User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual